Haier HSU-09HEA03-BP, 10518526, HSU-12HEA03-BP User Manual

Page 1
SPLIT TYPE ROOM AIR CONDITIONER
OPER
ATION MANUAL
HSU-09HEA03/(BP) HSU-12HEA03/(BP)
Please read this operation manual before using the air conditioner.
0010518526
Page 2
Cautions
Disposal of the old air conditioner
Before disposing an old air conditioner that goes out of use, please make sure it's inop­erative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment.
It must be noticed that air conditioner system contains refrigerants, which require speciali­zed waste disposal. The valuable materials contained in an air conditioner can be recycled .Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of your air conditioner does not get damagedprior to being picked up by the relevant waste disposal center, and contribute to environmental awareness by insisting on an appropriate, anti-pollution method of disposal.
Disposal of the packaging of your new air conditioner
All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment.
The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service. The wrapping bag made of polyethylene and the polyethylene foam pads
contain no fluorochloric hydrocarbon.
All these valuable materials may be taken to a waste collecting center and used again after adequate recycling.
Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house.
Safety Instructions and Warnings
Before starting the air conditioner, read the information given in the User's Guide caref­ully. The User's Guide contains very impor­tant observations relating to the assembly, operation and maintenance of the air conditioner.
The manufacturer does not accept respon­sibility for any damages that may arise due to non-observation of the following instruction.
Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier.
Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.
Installation shall be done by professional people, don't install unit by yourself.
For the purpose of the safety,the air con­ditioner must be properly grounded in acco­rdance with specifications.
Always remember to unplug the air conditioner before openning inlet grill. Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.
All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major source of danger for the user of the air conditioner.
Do not damage any parts of the air conditioner that carry refrigerant by piercing or performating the air conditioner's tubes with sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts out and gets into eyes, it may result in serious eye injuries.
1
Page 3
Cautions
Do not obstruct or cover the ventilation grille of the air conditoner.Do not put fingers or any other things into the inlet/outlet and swing louver.
Do not allow children to play with the air conditioner.In no case should children be allowed to sit on the outdoor unit.
Specifications
The refrigerating circuit is leak-proof.
The machine is adaptive in following situation
1.Applicable ambient temperature range:
Cooling
Heating
Indoor
Outdoor
Indoor
Outdoor
Maximum:D.B/W.B Minimum:D.B/W.B
Maximum:D.B/W.B Minimum:D.B
Maximum:D.B Minimum:D.B
Maximum:D.B/W.B Minimum:D.B/W.B
32oC/23oC
o
18
C/14oC
o
43
C/26oC
o
18
C
o
C
27
o
15
C
o
24
C/18oC
o
C/-8oC
-7
7. The appliance is not intended for use by young children or infirm persons
without supe
rvision.
8. Young children should be supervised to ensure that th the applienc
9.Please empl which fit into the p
ey do not play with
e.
oy the proper power plug,
ower supply cord.
10 .The power plug and connecting cable
must have acquired the local attestation.
11.In order to protect the units,please turn
off the A/C first, and at least 30 seconds later, cutting off the power.
2. If the power supply cord is damaged, it must be replaced by the manufacturer
or its service agent or a similar qualified person.
3. If the fuse of indoor unit on PC board is broken,please change it with the type of
T. 3.15A/ 250V.
4. The wiring method should be in line with the local wiring standard.
5. After installation, the power plug should be easily reached.
6. The waste battery should be disposed properly.
2
Page 4
Parts and Functions
Indoor Unit
Display board
Inlet
Air Purifying Filter
(inside)
Inlet grille
Horizontal flap (adjust up and down air flow. Don't adjust it manually)
Outlet
Air filter(inside)
Power plug
Anion generator
(inside)
Vertical blade
(adjust left and right air flow)
Actual inlet grille may vary from the one shown in the manual according to the product purchased
Outdoor Unit
OUTLET
INLET
HSU-09HEA03/(BP) HSU-12HEA03/(BP)
CONNECTING PIPING DRAIN HOSE
3
AND ELECTRICAL WIRING
Page 5
Parts and Functions
Remote controller
1
2 3 4
12
13
14 15
16
18
1. Operation mode display
Operation mode
Remote controller
Display board
2. SWING display
3. FAN SPEED display
4. HEALTH display
5. POWER/SOFT display
6. LOCK display
A U
o
T O
ON/OFF
MODE SET
FAN
SWING
LOCK RESET
TEMP
HEALTH
COOL DRY
ON OFF
AM PM
C
TIMER
CLOCK
POWER/SOFT
AUTO
HEAT
HI
17
10
19
20
21
22
24
23
6
11
5
Display board
7 8
9
25
7. SIGNAL SENDING display
8. TIMER OFF display
9. TIMER ON display
10. CLOCK display
1
26
11. TEMP display
12. POWER ON/OFF
Used for unit start and stop.
13. MODE
Used to select
14. FAN
Used to select fan speed AUTO, HI, MED, LO
15. HOUR
Used to set clock and timer setting.
DRY,HEAT operation
COOL,
16. SWING
Used to set auto fan direction.
17. POWER/SOFT button
18. LOCK
Used to lock buttons and LCD
19. TEMP.
Used to select your desired temp.
20. SET
Used to confirm timer and clock settings.
21. TIMER
Used to select TIMER ON, TIMER OFF,
22. CLOCK
Used to set correct time
23. RESET
Used to reset the controller back to normal condition.
24. HEALTH
LOMED
Used to operate the healthy function
25.
Singal receiver hole
26. Ambient temp.display
When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed and this room temperature is only for reference.
displa
4
y.
9
8
1
5
Clock set
When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Press or to set correct time. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. After time setting is confirmed, press SET
, "AM "and "PM" stop flashing, while clock
NOTE: Cooling only unit do not have displays and functions related with heating
The unit do not have functions related with healthing.
Hints
After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal.
4
starts working.
Page 6
Operation
Remote controller's operation
When in use, put the signal transmission head directly to the receiver hole on the indoor unit.
The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.
Don't throw the controller, prevent it from being damaged. When electronic-started type fluorescent lamp or change-over
type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter.
Loading of the battery
Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder)
Remove the battery cover:
Slightly press " " and push down the cover.
Ú
½ ½ Á
Æ Å
·
Æ
ª
Î
»
, ±
Ò
Ê
¬
¡
Í
Ã
È
Ã
Ó
Ø
Ó
»
³
¡
²
ë
ç
Ñ
ä
Ç
µ
,
ë
«
¼
£
Ç
³
±
½
ì
Ù
Ê
ë
Ò
¤
Ô
#
Ç
³
ö
ó
,
¹
7
º
Ó
Ø
Ò
ç
Ó
³
©
ç
È
Ö
µ
Â
Ð
¹
Ö
·
Ö
Ö
6
,
Ã
À
· ö
Ó
³
¹
¡
£
£
¡
¡
Ê
È
ö
Ø
³
Ú
Ø
³
³
ç
û
Ô
ç
µ
µ
¾
£
Â
«
Ë º º
«
Ð
½
¹
µ
ë
à
Ü
È °
×
Ç
×
Þ
Å
Ï
Í ¯
Ð
¼
Ó
û
÷
Æ £ º
÷
µ Õ ¿
Load the battery:
Be sure that the loading is in line with the" + "/"-" pole request as illustrated.
Put on the cover again Confirmation indicator:
In disorderation, reload the batteries or load the new batteries after 6mins.
Note:
Use two new same-typed batteries when loading. If the remote controller can't run normally or doesn't work at all, use a sharp pointed item to press the reset key.
Hint:
Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out just need to press reset key.
ÇëÑ¡ÓÃÍ¬Ò»Æ·ÅÆÁ½½Ú ÇëÑ¡ÓÃÍ¬Ò»Æ·ÅÆÁ½½Ú 7# µç³Ø,³¤Ê±¼ä²»ÓÃʱ,Ϊ
·АЦ¹В©Т¹Зл½«µз³ШИ¡ ³ц¡£ ФЪК¹УГЦРИзУцТм³£,Зл ½«µз³ШИ¡³ц,6·ЦЦУºуФЩ Ч°ИлРВµз³Ш¡£
º£¶ы¼¯НЕЗаµºº£¶ы ¿ХµчЖчУРПЮЧЬ¹«Л¾
7#
µç³Ø,³¤Ê±¼ä²»ÓÃʱ,Ϊ
·Àֹ©ҹÇ뽫µç³ØÈ¡
³ö¡£
ФЪК¹УГЦРИзУцТм³£,Зл
½«µç³ØÈ¡³ö,6·ÖÖÓºóÔÙ
×°ÈëÐÂµç³Ø¡£
º£¶û¼¯ÍÅÇൺº£¶û
¿ХµчЖчУРПЮЧЬ¹«Л¾
5
Page 7
Operation
Cool Operation
(1) Unit start
Press ON/OFF button, unit starts. Previous operation status appears on display.(Not Timer setting)
(2) Select operation mode
Press MODE button. For each press, operation mode changes as follows:
ON/OFF TEMP
COOL DRY HEAT
Unit will run in operation mode displayed on LCD. Stop display at your desired mode.
(3) Select temp. setting
Press TEMP button.
Every time the button is pressed, temp. setting increases 1oC Every time the button is pressed, temp. setting decreases 1oC
Unit will start running to reach the temp. setting on LCD.
(4) Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
AUTO
Air conditioner is running under displayed fan speed.
Air conditioner is running under displayed fan speed.
HI
LOMED
4
MODE
2
FAN
LOCK
1
3
HEALTH
SET
TIMER
CLOCKSWING
POWER/SOFT
RESET
(5) Unit stop
Press ON/OFF button, the unit stops.
Hints
On cooling only unit, heating mode is not available. Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status.
No reelecting is needed.(TIMER ON/OFF、SWING needs reelecting)
6
Page 8
Operation
Heat Operation
(1) Unit start
Press ON/OFF button, unit starts. Previous operation status appears on display.(Not Timer setting)
(2) Select operation mode
Press MODE button. For each press, operation mode changes as follows:
COOL DRY
HEAT
Unit will run in operation mode displayed on LCD. Stop display at your desired mode.
(3) Select temp. setting
Press TEMP button.
Every time the button is pressed, temp. setting increases 1 Every time the button is pressed, temp. setting decreases 1oC
Unit will start running to reach the temp. setting on LCD.
(4) Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
Remote controller:
AUTO
HI
IN HEAT mode, warm air will blow out after a short period
prevention function.
LOMED
ON/OFF TEMP
1
5
MODE
2
o
C
LOCK
3
FAN
4
HEALTH
of the time due to cold-draft
3
SET
TIMER
CLOCKSWING
POWER/SOFT
RESET
(5) Unit stop
Press ON/OFF button, the unit stops.
Hints
Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status.
7
Page 9
Operation
Dry Operation
(1) Unit start
Press ON/OFF button, unit starts.
(2) Select operation mode
Press MODE button. For each press, operation mode changes as follows:
COOL DRY
HEAT
Unit will run in operation mode displayed on LCD. Stop display at your desired mode.
(3) Select temp. setting
Press TEMP button.
Every time the button is pressed, temp. setting increases 1oC Every time the button is pressed, temp. setting decreases 1oC
Unit will start running to reach the temp. setting on LCD.
(4) Fan speed selection
Press FAN button. For each press, fan speed changes as follows:
AUTO
HI
Unit runs at the speed displayed on LCD. In DRY mode, when room temperature becomes
lower than temp.setting+2oC,unit will run intermittently at LOW speed regardless of FAN setting.
LOMED
ON/OFF TEMP
6
MODE
2
5
COOL operation starts when room temp. is higher than temp. setting.
Temp. setting+2oC
Temp. setting
On reaching temp. setting, unit will run in mild DRY mode.
FAN
LOCK
1
4
HEALTH
3
Ultra-low air flow
3
SET
TIMER
CLOCKSWING
POWER/SOFT
RESET
Hints
Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status.
8
Page 10
Operation
(5) Air flow direction adjustment
After operation mode is selected, horizontal flap will open automatically according to the mode. Referring to the Fig.
COOL
About 10
o
Up and down (Use remote controller)
Press SWING button, horizontal flap will move within the range shown in the Fig. Press SWING button stop it at a fixed position.
o
o
COOL
About 10
About 45
Cautions:
It is advisable not to keep horizontal flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur.
(6) Unit stop
Press ON/OFF button. Only time remains on LCD. All indicators on indoor unit go out. Horizontal flap closes automatically.
Left and right air flow adjustment (manual)
Move the vertical blade by a knob on air conditioner to adjust left and right direction referring to Fig.
Cautions:
When humidity is high, condensate water might occur at air outlet if all vertical louvers are adjusted to left or right.
Cautions:
Unit won't restart until 3 minutes have elapsed, due to system protection.
Hints
As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. Be careful not to catch a cold when cold air blows downward. It is harmful to your health in summer to go frequently in and out of places where temp. di
fference is above 7oC. Temp. difference of 3-5oC will remove your fatigue. More than this, unit's load can be reduced and power consumption cut down as well. So, you'd better set a temp. difference of 3-5oC between indoor and outdoor temp. in COOL mode.
9
Page 11
Operation
TIMER Operation
Set Clock correctly before starting Timer operation
You can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night.
TIMER ON/OFF
(1)After unit start, select your desired operation mode. Operation mode will be displayed on LCD. Power indicator on indoor unit lights up.
(2)TIMER mode selection
Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows:
ON OFF
TIMER ON TIMER OFF
Select your desired TIMER mode (TIMER ON or TIMER OFF) ON or OFF will flash.
blank
(3)Timer setting
Press HOUR / button.
Every time the button is pressed, time increases 1 hour.
If button is kept depressed, time will change quickly.
Every time the button is pressed, time decreases 1 hour. If button is kept depressed, time will change quickl will be shown on LCD. It can be adjusted within 24 hours.
y. Time
(4)Confirming your setting
After setting correct time, press SET button to confirm, "ON" or "OFF" stops flashing Time displayed: Unit starts or stops at x hour . (TIMER ON or
TIMER OFF).
Timer mode indicator on indoor unit lights up.
ON/OFF TEMP
1
MODE
3
HEALTH
3
2
CLOCKSWING
POWER/SOFT
FAN
LOCK
ON
SET
TIMER
RESET
4
To cancel TIMER mode
Just press TIMER button several times until TIMER mode disappears.
Hints
After replacing batteries or a power failure happens, Time setting should be reset. Remote controller possesses memory function, when use press SE
T button after mode selecting if timer setting is the same as previous one.
10
TIMER mode next time, just
Page 12
Operation
POWER/SOFT Operation
POWER Operation
When you need rapid heating or cooling, you can use this funciton.
Selecting of POWER operation
Press POWER/SOFT button. Every time the button is pressed,display
changes as follows:
POWER
SOFT
BLANK
ON/OFF TEMP
MODE
FAN
SET
TIMER
Stop the display at
In POWER operation status:
In COOL mode, fan speed automatically runs in HI mode for 15 min then returns to original status setting.
To cancel POWER operation
LOCK
Press POWER/SOFT button twice ,POWER/SOFT disappears.
SOFT Operation
You can use this function when silence is needed for rest or reading.
Selecting of SOFT operation
Press POWER/SOFT button. Every time the button is pressed,display
changes as follows:
POWER
SOFT
Stop the display at
In SOFT operation mode, fan speed automatically takes"LOW"
To cancel POWER operation
Press POWER/SOFT button twice ,POWER/SOFT disappears.
BLANK
HEALTH
CLOCKSWING
POWER/SOFT
RESET
Hints: During POWER operation, in rapid COOL mode, the roor will show inhomogeneous temperature distribution. Long period SOFT operation will cause effect of not too cool.
11
Page 13
Operation
Emergency operation and test operation
Emergency Operation:
Carry out this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, a" Pi "sound starts once, which means the start of this operation. In this operation, it is not possible to change the settings of temperature and air flow speed, it is also impossible to do an operation by the timer. Follow the requirements below.
Pi
Room temperature
More than 23oC
Less than 23
o
Designated temperature
23
C
26
o
C
o
C
Timer mode
CONTINUOUS
CONTINUOUS
Air flow speed
AUTO
AUTO
Operation mode
COOL
HEAT
If an air conditioner is a model for both cooling and heating.
Cooling when the room temperature at the start of operation is above 23oC. Heating when the room temperature at the start of operation is below 23oC
Test operation:
Use this switch in the test operation when the room temperature is less 16 operation. Continue to press the test operation switch for more than 5 seconds. release your finger from the switch, the cooling operation starts with the air flow speed setting "Hi".
o
C, do not use it in the normal
After you hear the "Pi" sound twice,
Pi Pi
Removal of the restriction of emergency or test operation:
Press once more the emergency operation switch, or manipulate through the remote controlle removed. When the remote controller is manipulated for the removal, then by the remote controlle
r, a "Pi" sound causes the restriction of emergency or test operation to be
the selected operation
r.
12
Page 14
Maintenance
Replacement of Air Purifying Filter
1.Open the lnlet Grille
Prop up the inlet grille by using a small device named
grille-support which located in the right side of the ind-
oor unit.
2.Detach the standard air filter
Slide the knob slightly upward to release the filter, then withdraw it.
3.Attach Air Purifying Filter
Put air purifying filter appliances into the right and left filter frames.
Detach old Air Pu
rifying Filter
4.Attach the standard air filter
(Necessary installation)
ATTENTION:
The white side of the photocatalyst air purifying filter face outside, and the black side face the unit. The green side of the bacteria-killing medium air purifying filter face outside, and the white side face the unit.
5.Close the Inlet Grille
Close the Grille surely
NOTE:
The photocatalyst air purifying filter will be solarized in fixed time. In normal family, it will be solarized every 6 months.
The bacteria-killing medium air purifying filter will be used for a long time,no need for replacement. But in the period of using them ,you should remove the dust frequently by using vacuum cleaner or flaping them lightly,otherwise ,its performance will be
affected.
Please keep the bacteria-killing medium air purifying filter in the cool and dry conditions avoid long time directly sunshine when you stop using it,or its ability of sterilization will be reduced.
13
Page 15
Maintenance
For Smart Use of The Air Conditioner
Setting of proper room temperature
Proper temperature
Close doors and windows during operation
During cooling operation prevent the penetration of direct sunlight with curtain or blind
Do not block the air inlet or outlet
Use the timer effectively
If the unit is not to be used for a long time, turn off the power supply main switch.
OFF
Use the louvers effectively
14
Page 16
Cautions
Safety Instruction
Please read the following Safety Instructions carefully prior to use.
The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use.
Installation
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works may cause electric shock, fire, water leakage.
lnstallation in a inadequate place may cause accidents. Do not install in the following place.
CAUTION
Connect the earth cable.
earthing
Do not install in the place where there is any possibility of inflammable gas leakage around the unit.
PROHIBITION PROHIBITION
Do not get the unit exposed to vapor or oil steam.
15
Check proper installation of the drainage securely
STRICT ENFORCEMENT
Page 17
Cautions
When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop.
WARNING
Use an exclusive power source with a circuit breaker
OFF
Connect power supply cord to the outlet completely
STRICT
ENFORCEMENT
Do not use power supply cord in a bundle.
PROHIBITION
Do not start or stop the operation by disconnecting the power supply cord and so on.
PROHIBITION
Do not use for the purpose of storage of food, art work, precise equipment, breeding, or cultivation.
STRICT
ENFORCEMENT
Use the proper voltage
STRICT
ENFORCEMENT
Take care not to damage
the power supply cord.
PROHIBITION
Do not channel the air flow directly at people, especially at infants or the aged.
PROHIBITION
CAUTION
Take fresh air occasionally especially when gas appliance is running at the same time.
Do not use power supply cord
extended or connected in halfway
PROHIBITION
Do not insert objects into the air inlet or outlet.
PROHIBITION
Do not try to repair or reconstruct by yourself.
Do not operate the switch with wet hand.
PROHIBITION
Do not install the unit near a fireplace or other heating apparatus.
PROHIBITION
Do not place animals or plants in the direct path of the air flow
PROHIBITION
STRICT
ENFORCEMENT
Check good condition of the installation stand
PROHIBITION
Do not place any objects on or climb on the unit.
PROHIBITION
16
PROHIBITION
Do not pour water onto the unit for cleaning
PROHIBITION
Do not place flower vase or water containers on the top of the unit.
PROHIBITION
Page 18
Trouble shooting
Before asking for service, check the following first.
Normal Performance inspection
Phenomenon
The system does not restart immediately.
Noise is heard
Smells are generated.
Mist or steam are blown out.
Cause or check points
When unit is stopped, it won't restart immediately until 3 minutes have elapsed to protect the system. When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner.
During unit operation or at stop, a swishing or gurgling noise may be heard. At first 2-3 minutes after unit start, this noise is more noticeable. (This noise is generated by refrigerant flowing in the system.) During unit operation, a cracking noise may be heard. This noise is generated by the casing expanding or shrinking because of temperature changes Should there be a big noise from air flow in unit operation, air filter may be too dirty.
This is because the system circulates smells from the interior air such as the smell of furniture, cigarettes.
During COOL or DRY operation, indoor unit may blow out mist. This is due to the sudden cooling of indoor air.
Does not work at all.
Multiple
check
Poor cooling
Application temp. range of air conditioner -7oC~43oC.
Is power plug inserted? Is there a power failure? Is fuse blown out?
Is the air filter dirty? Normally it should be cleaned every 15 days. Are there any obstacles before inlet and outlet? Is temperature set correctly? Are there some doors or windows left open? Is there any direct sunlight through the window during the cooling operation?(Use curtain) Are there too much heat sources or too many people in the room during cooling operation?
17
Loading...