COOKER/MIXER models DL-40 TA/3, DL-60 TA/3 & DL-80 TA/3
Description
Cooker Mixer Kettle shall be a Groen Model DL-40, 60, 80, TA/3 (Specify 40-, 60or 80gallon) stainless steel 2/3 steam jacketed unit operating from a direct steam source and complete with console-mounted tilt-out twin shaft scraper mixer.
Construction
Kettle interior shall be 316 stainless steel, solid one-piece welded construction. Kettle jacket shall be 304 stainless steel solid one piece construction. Unit shall be provided with a heavy-duty reinforced rim with a heavy-duty but- terfly-shaped pouring lip for maximum sanitation and durability. Unit includes 10-gallon etch markings, double pantry faucet and steam regulating system.
Kettle to be tilting type with a positive locking worm and gear tilt mechanism enclosed in a polished, drip-proof stainless steel housing. Kettle mounted on a polished, stainless steel tri-leg stand with stainless steel floor flanges.
Agitator Assembly
Enclosed power transfer case to be cast aluminum with a 3-to-1 gear ratio. Gear motor to be completely enclosed type, cast iron housing, right angle shaft down, helical bevel gearing, variable speed motor driven through a variable electronic speed control. See table on back for minimum and maximum agitator speeds.
Main agitator to be anchor-type, shaped to the contour of the kettle and provided with removable nylon finger scrapers. The secondary counter rotating agitator to be centrally located between the center shaft and the outside arms of the main agitator. Both agitators are attached with bayonet connections for easy, quick removal for cleaning or when kettle is to be used as a without the mixing mechanism. Both agitators are 304 stainless steel and either can be used alone. Agitator assembly and motor drive can be manually tilted out to the back of the kettle.
Finish
Kettle interior shall be polished to a 180 emery grit finish. Kettle exterior shall be finished to a bright semi-deluxe buff finish to ensure maximum ease in cleaning and maintaining brilliant appearance.
ASME Code
Unit shall be ASME shop-inspected, stamped and registered with the National Board for operation up to a maximum working pressure of 50 PSIG.
Sanitation
Unit shall be designed and constructed to be NSF listed, meeting NSF requirements.
Drawoff
Bottom outlet to be 2” flush mounted, sanitary, quick opening ball valve.
Steam Pressure
Kettle shall operate dependably at steam pressure of 50 PSIG or below (to a minimum of 5 PSIG). Higher working pressure available. The steam supply shall be injected directly into the jacket through the trunnion and the condensate shall be removed through a tube contained in the jacket and connected to the opposite trunnion. No exposed steam piping or obstructions shall be on the kettle body.
Controls
Agitator to be electronic, variable speed-control type, capable of operating at any RPM between maximum and minimum settings.
Installation Requirements
3/4” NPT steam inlet and condensate connection are provided. A remote steam source is required. A steam trap assembly with check valve and globe valve is provided as standard .
Unit requires agitator power connection, specify 208 Volt (1 or 3-phase is standard). Other voltages are available.
Options/Accessories
240, 480 Volt Power Supply (For agitator motor)
Kettle Brush Kit
Pan Carrier
Wall Mount With In Wall Carrier
Gallon Master
Basket Insert
Cold Water Cooling
Working Pressure (higher or lower than 50 PSIG)
Lip strainers
Contour measuring strips
Origin of Manufacture
Cooker/Mixer shall be designed and manufactured in the United States.
Stainless Steel
2/3 Steam Jacketed
Cooker/Mixer
Floor-Mounted, Tilting,
Direct Steam 40, 60 or 80Gallon Capacity
with Twin Shaft Agitator
Short Form
GROEN Model DL-40, 60, 80 TA/3 (Specify gallons) stainless steel, tilting, steam jacketed, cooker/mixer with tilt-out twin shaft agitator. Kettle tilt mechanism to be positive locking worm and gear enclosed in drip-proof stainless steel housing. Twin shaft agitator assembly standard with multi scraping fingers and the second agitator is counter rotating mixer; with mechanically assisted tilt-out mechanism and positive, quick-action rim lock and latch. 316 stainless steel kettle body solid, onepiece, welded construction with heavy-duty reinforced rim and butterfly-shaped pouring lip. Unit standard with 2” flushmounted ball valve and etch marks. Kettle mounted on stainless steel tri-leg stand. ASME code-constructed and National Board registered for operation up to 50 PSI and NSF listed. Specify 208 Volt (3 or 1-phase) for agitator assembly electric connection. Made in USA.
Applications
Wet roasting meats
Soups
Stews
Stocks
Poultry
Sauces
Pie Fillings
Vegetables
Pasta
Rice
Gravies
1055 Mendell Davis Drive, Jackson, MS 39272
888-994-7636, unifiedbrands.net
Please reference our website for the most updated product information and specifications.
Groen Cooker/Mixer, Page 7
141050C
Revised 08/09
Loading...