Groen DL-20 User Manual

DIRECT STEAM KETTLE

PROJECT NAME:

LOCATION:

ITEM NO:

MODEL DL

Kettle shall be a Groen Model DL (Specify 20, 40, 60 or 80-gallon) stainless steel,
2/3 steam jacketed unit operating from direct steam.

CONSTRUCTION: Kettle interior shall be of

type 316 stainless steel with solid one-piece welded
construction. Kettle jacket shall be 304 stainless steel,
solid one piece construction. Unit shall be furnished with
a heavy reinforced bar rim with a heavy-duty, butterfly­shaped pouring lip welded to the top rim of kettle to
ensure proper pouring control at all times and to allow
the kettle to be used to its full working capacity and for
maximum sanitation and durability.

Kettle body shall be supported by a stainless steel yoke
stand with tubular leg supports. Self-locking worm gear
tilt mechanism and rotary steam joint are completely
enclosed in stainless steel housing, mounted on the
right kettle support arm. Large hand crank provides
easy operator tilting and precise pouring control. Faucet
mounting bracket is standard.

STEAM PRESSURE: Kettle shall operate

dependably at any steam pressure between 5 and 25
PSI. Higher working pressures available.

MOUNTING: Kettle shall be trunnion-mounted

to a sturdy stainless steel tubular leg stand with
adjustable floor flanges.

INSTALLATION: Remote steam source required.

Steam trap assembly is required and not provided
unless ordered as an option. (See below) See
dimension H on other side for steam inlet size and
number.

ORIGIN OF MANUFACTURE: Designed and

manufactured in the United States.

QTY:

MODEL NO:

AIA NO:

SIS NO:

SHORT FORM: Stainless steel

2/3 Steam Jacketed Kettle, Floor
Mounted, Tilting, Direct Steam.
20-80 gallon capacities.
(model DL shown)

FINISH: Kettle interior shall be polished to a 180

emery grit finish. Exterior of kettle shall be finished to
a semi-deluxe buff finish, ensuring maximum ease in
cleaning and maintaining brilliant appearance.

ASME CODE: Unit shall be ASME shop-inspected,

stamped and registered with the National Board for
operation up to a maximum working pressure of 25 PSI.

SANITATION: Unit shall be designed and

constructed to be NSF-listed, meeting NSF and all known
health department and sanitation codes.

COVER: A cover is optional. No. 31 lift-off cover

available for 20 to 80-gallon models. No. 51 counter­balanced cover available on 40 to 80-gallon models.

OPTIONS/ACCESSORIES:

Basket Inserts (TRI-BC)
Water fill faucets (single or

double pantry)
Lift off cover
Counterbalanced hinged cover kit
2” or 3” tangent draw-off valve
Cold water cooling
Steam trap assemblies
Kettle brush kit
1/8” perforated disc strainer
1/4” perforated disk strainer
Solid disc strainer
Lip strainers
Pan carrier (40 and 60-gallon)
Contour measuring strip
Gallon etch marks
Contour measuring strip
Gallon etch marks

Braising Pans

144357H Revised 04/12

Stainless steel 2/3 Steam Jacketed Kettle, Floor
Mounted, Tilting, Direct Steam. 20-80 gallon capacities.

P/N 146528 REV E

MODEL DL

V

-I.P.S

J

STEAM OUTLET

D

B

C

G

U

F

E

FAUCET MOUNTING BRACKET
WITH 1-3/8 DIA HOLE IS
STANDARD AND FURNISHED

-I.P.S. STEAM INLET

H

A

SELF LOCKING WORM &
GEAR TILTING MECHANISM

POUR PATH

OPEN

CONDENSATE
DRAIN TUBE

M M

6

7-1/2

JACKET DRAIN
PETCOCK

*

ADJUSTABLE LEG FLANGES

(5/8")

L

MAX. POUR PATH
APPROXIMATE

*OPTIONAL

P

*

S

4

*

5-1/2

T

R

NOTES:

1. APPROX. 5 P.S.I. REQD. TO PUSH CONDENSATION UP DRAIN TUBE.

2. LEG FLANGES MUST BE SECURELY ANCHORED TO THE FLOOR.

3. DIMENSIONS R & T REFER TO KETTLES WITH 2" DRAWOFF VALUE.

2" OR 3" COMPRESSION DISK.

TYPE SANITARY DRAWOFF VALVE

FURNISHED WHEN SPECIFIED AT EXTRA

COST (SEE NOTE 3)

5

(TYPICAL FLOOR FLANGE)

K

W

3-3/4 B.C.

7/16 DIA. (3 HOLES)

A.S.M.E. APPROVED SAFETY VALVE

N

A

B

C

D

E

F

G

H

J

K

L

M

N

P

R

S

T

U

V

W

P/N 5662001 REV D

21 7/16

TABLE OF DIMENSIONS

CAPACITY (GALLONS/LITRES)

MM

508

470

914 36

33013

511 23

600123

---

---

270326

533

3131515

340

241

317

381 11

921

733

314

40/152

MM

INCHES

660

26

22

559

914

17

432

3

603

4

1

489410

4

597

2

3

---

4

3

---

4

1

165 10

2

813

5

389

16

381

1

12

317

2

1

13

343

2

1

292

2

1

11375

4

43

1092 1194

1

34 38

876

2

1

12 14

318

2

20/76

INCHES

20

1

18

2

36

1

20

8

1
8

5

23

8

3
4

3
4

5

10

8

21

5

12

16

13

9

1

12

2

15

3

14

4

1

36

4

7

28

8

3

12

8

3
8

1
2

R13

30-5/8

LEG LOCATION

60/228

MM

INCHES

762

30

635

25

1118

44

483

19

3

654

25

4

1

540

211916

4

1

29

743

4

3

---

4

3

---

4

1

260

4

787

31

5

17

440

16

3

16

426

4

12

305

1

14

368

2

1

16

419

2

1

41316286

4

47

1

972 997

4

3

375 426

4

80/304

INCHES

MM

813

2932737

48

1219

50820

3

680

26

4

1

22

565

4

1

794

31

4

3

---

4

3

---

4

1

286

11

4

787

31

3

18

476

4

3

426

16

4

13

330

3

13 349

4

1

16

419

2

1

16 413

4

49

1245

1

39

4

3

16

4

15

1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net

© 2011 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.