GoDEX ZX1200i User Manual [nl]

Page 1
ZX1200i/ZX1300i/ZX1600i BARCODE PRINTER
USER MANUAL
User Manual Version Issue Date P/N
: ZX1200i series : Rev. 1.0 : 2013.12.12 : 920-015111-00
Page 2
ZX1200i/ZX1300i/ZX1600
2
Printer Setup
004
3
Printer Setting and Control
017
Appendix
USER MANUAL
CONTENTS
1 Barcode Printer 001
i
1.1
1.2
2.1
2.2
2.3
2.4
3.1
3.2
3.3
3.4
3.5
3.6
Box Content
Getting to Know Your Printer
Loading the label roll
Loading & Removing the Ribbon
Connecting the Printer to the Host Computer
Installing Printer Driver and GoLabel with Super
Wizard CD
Operation Panel
LCD Interface Introduction
LCD Interface Function
Label Calibration and Self-Test
Error Alerts
USB Host
001
002
004
008
011
012
017
018
023
028
030
031
4 NetSetting for Ethernet 034
4.1
4.2
5 Accessories 042
5.1
5.2
6 Maintenance and Adjustment 046
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
Installing the NetSetting Software
The Interface of NetSetting
Preparation Steps
Installing the Cutter
Insta
lling / removing the print head module
Adjusting the print line
Adjusting ribbon tension
Cleaning the thermal print head
Adjusting the balance and print head tension
Ribbon shield settings
Cutter settings
Troubleshooting
034
035
042
039
046
047
48
49
50
51
52
53
Contents
Page 3
ZX1200i/ZX1300i/ZX1600
i
USER MANUAL
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS
This equipment has been tested and found to comply with the limits for a CLASS A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at own expense.
ZX1200i SERIES TO WHICH THIS DECLARATION RELATES IS IN CONFORMITY WITH THE FOLLOWING STANDARDS
European Standard EN 55022:2010/AC:2011 Class A,EN 61000-3-2:2006/A1:2009 and /a2:2009, EN 61000-3-3:2008 and
EN55024:2010(IEC 61000-4-2:2008, IEC 61000-4-3:2006/A1:2007/A2:2010, IEC 61000-4-4:2004/A1:2010, IEC 61000-4-5:2005,
IEC 61000-4-6:2008, IEC 61000-4-8:2009, IEC 61000-4-11:2004). CFR 47, Part 15
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
此为Class A产品,在生活环境中,该产品可能造成无线电干扰,在这种情况下,可能需要用户对其干扰采取切实可行 的措施。
Declaration
Declaration
Page 4
ZX1200i/ZX1300i/ZX1600
i
USER MANUAL
SAFETY INSTRUCTIONS
Please read the following instructions carefully.
1. Keep the equipment away from humidity.
2. Before you connect the equipment to the power outlet, please
check the voltage of the power source.
3. Make sure the printer is off before plugging the power connector
into the power jack.
4. It is recommended that you connect the printer to a surge
protector to prevent possible transient overvoltage damage.
5. Be careful not to get liquid on the equipment to avoid electrical
shock.
6. For safety and warranty reasons, ONLY qualified service personnel
should open the equipment.
7. Do not repair or adjust energized equipment under any
circumstances.
Caution
**** Danger of explosion if battery is incorrectly replaced. Replace only with the equivalent type recommended by
the manufacturer.
**** Dispose of used batteries according to the manufacturer’s instructions.
**** Only use with designated power supply adapter model.
**** Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Specifications are subject to change without notice.
Safety instructions
Page 5
1 Barcode Printer
1.1 Box Content
Please check that all of the following items are included with your printer.
ZX1200i / ZX1300i / ZX1600i Barcode Printer
Label Stock
Ribbon
USB Cable
Power Adapter
Power Cord
ZX1200i / ZX1300i / ZX1600i Series
Quick Guide
ZX1200i / ZX1300i / ZX1600i
CD
Including GoLabel software
and user’s manual.
Series
Page 6
1 Barcode Printer
1.2 Getting to Know Your Printer
Device Overview
Front View
Stylus Pen
TOUCH PANEL
POWER BUTTON
FEED BUTTON
PRINTER COVER
VIEWING WINDOW
LOWER COVER PLATE
USB HOST
Rear View
Feed slot for continuous labels
Calibration button Ethernet port
Serial port (DB-9)
Applicator Interface(OPTION)
USB port USB Host
Parallel port(OPTION)
Power jack
On/Off switch
2
Page 7
1 Barcode Printer
The Internal View of Printer
Ribbon rewind hub
Ribbon supply hub
RFID module
RFID module
Print mechanism
Platen roller
Release lever for print head
Paper guide
Label tension guide
Label supply hub
Label roll guide
Adjustable Sensor
Paper guide
3
Page 8
2 Printer Setup
2.1 Loading the label roll
This printer supports the following printing methods: Thermal transfer printing (TTP)Requires a ribbon for transferring a printed image to a medium. Direct thermal printing (DTP)Does not require a ribbon, only thermal paper.
Please check which printing method you are using and alter the settings accordingly in the printer driver,
printer menu, and/or software.
Place the printer on a flat surface and open the printer cove
Turn it anticlockwise to a top right position as shown in the illustration
4
Page 9
2 Printer Setup
Now slide the label roll guide forward and fold it down
Place the label roll on the label supply hub , pushing it right up to the printer housing.
(Do not apply too much pressure to avoid damaging the label stock.)
Note
* When moving the label roll guide, hold it only by the end that is attached to the bracket, not by its top.
5
Page 10
2 Printer Setup
Load the label roll into the printer as shown in the illustration. Pass it through the printer as indicated by the red arrows.
Pass the label stock through the Adjustable Sensor and up to the tear-off plate.
Note
* Remember to set the movable sensor to gap, black mark, or tag hole by changing the position of the sensor with the
adjustment wheel.
6
Page 11
2 Printer Setup
1
2
2. Return the print head release lever to its original position.
1
1. The labels pass between the wall of the printer housing and the adjustable paper guide.
Then close the printer cover.
7
Page 12
2 Printer Setup
2.2 Loading & Removing the Ribbon
Loading Ribbon
Place the printer on a flat surface and open the printer cover
Place a new ribbon on the ribbon supply hub.
The two illustrations as below show you how to install the ribbon depending on the ribbon type (ink side in or out).
Ink side out Ink side in
8
Page 13
2 Printer Setup
Pass the ribbon under the print head and back up on the other side. Attach it to the empty ribbon core.
Note
* Do not pass the ribbon under the sensor.
9
Page 14
2 Printer Setup
2.3 Connecting the Printer to the Host Computer
1. Please make sure that the printer is switched off.
2. Connect the power cord to the AC adapter and connect the adapter to the printer.
3. Connect the USB cable to the printer and host computer.
4. Switch on the printer. The operator panel should now light up.
ZX1200i / ZX1300i / ZX1600i
BARCODE PRINTER
10
Page 15
2 Printer Setup
2.4
1. Insert the Super Wizard CD in the CD/DVD drive of the host computer and the program should pop up
automatically.
You will see the Welcome screen first. On the Welcome screen, choose “Standard Installation”.
2. The wizard will then ask you to make sure your USB and power cables are connected and that the power is
turned on. Make sure that is done and then click “Next”.
Installing Printer Driver and GoLabel with Super Wizard CD
3. The next screen you will see to choose ‘’Download the latest version from GoDEX server’’ or ‘’Install from this
product disc.
11
Page 16
2 Printer Setup
4. As the printer driver and GoLabel are installing, a screen will display a progress bar.
5. Once the installation is complete, you can start to make and print labels with GoLabel or through the printer driver.
6. As the optional steps, you can also print a test label or register your printer during the “Standard Installation”
procedure.
Note
* If you need more resources, tools or reference documents, you can also find them on Super Wizard CD.
Just click “Other Choices” on Welcome Screen to access the files.
12
Page 17
2 Printer Setup
Installing Printer Driver Directly from CD Folder
1. Insert the product CD in the CD/DVD drive of the host computer and open the "Seagull Drivers" folder on the CD.
Select the icon for the driver file and click it to start the installation.
2. Follow the instructions on the screen. The Driver Wizard guides you through the installation procedure.
Select "Install printer drivers".
3. Specify your printer model.
Godex ZX1200i
13
Page 18
2 Printer Setup
4. Specify the port used to connect the printer to the host computer.
5. Enter a printer name and assign the appropriate rights.
Godex ZX1200i
Godex ZX1200i
6. Once the installation is complete, a summary of the printer settings is displayed.
Check whether the printer settings are correct and click "Finish" to start copying the driver files.
Wait until copying is complete, then finish the installation.
Godex ZX1200i
Godex ZX1200i
14
Page 19
2 Printer Setup
7. Once the driver installation is complete, the new printer should appear in the "Printers and Faxes" folder.
Godex ZX1200i
Godex ZX1200i
15
Page 20
3 Printer Setting and Control
3.1 Operation Panel
OPERATION TOUCH PANEL
POWER Button
Press the POWER button to turn on the printer, and the START UP SCREEN appears. The printer is on “ready to print”
status, the LCD screen should display the message “READY“ on the screen.
When printer is turned on, hold and press down the POWER button for 3 second will turn the printer off.
FEED Button
Turn on the printer and press the FEED button.
When you press the FEED button, the printer will advance media until the FEED button is released.
If you are using continuous labels, pressing the FEED button will advance a length of media until the button is released.
If you are using media with gaps, pressing the FEED button once will advance only one label.
If the label does not stop at the correct position, you need to run the auto-detection function for your media,
please see Section 3.4 Label Calibration and Self-Test.
TOUCH PANEL
FEED BUTTON
POWER BUTTON
PAUSE PRINTING_FEED Button
Pressing the FEED button while the printer is in standby mode will set the printer to pause mode. In this mode,
the printer can receive commands, but it will only process them when it is reset to standby mode. Pressing the
FEED button again will reset the printer to standby mode.
Pressing the FEED button during printing will interrupt printing. When the FEED button is pressed again, the printer
resumes printing. Example: While a 10-label print job is running, you press the FEED button to pause the printer.
Two of the labels have been printed. To resume printing and print the remaining eight labels, you will need to press
the FEED button again.
CANCEL PRINTING_FEED Button
Press and hold the FEED button for 3 seconds during printing cancels a print job. The current print job is cancelled.
Example: While a 10-label print job is running, you press the FEED button. Two of the labels have been printed.
The print job is cancelled and the remaining eight labels will not be printed.
16
Page 21
3 Printer Setting and Control
3.2 LCD Interface Introduction
Getting Started
Press the POWER button to turn on the printer, and the START UP SCREEN appears.
Power on
If the printer is on “ready to print” status, the LCD screen should display the message “Ready“ on the screen.
Use touch gestures to get around the Home screen and other screen for setting.
Tap the screen with your finger or the stylus pen when you want to select
on screen items such as settings icons.
ZX1200 V2.0000
Main
Wizard
Test
17
Page 22
3 Printer Setting and Control
On the Ready Page, three function mode for setting. You can make various setting functions in FUNCTIONAL MODE.
Main
ZX1200 V2.0000
Main
Wizard
ZX1200 V2.0000
Test
Printer
Setting
Label
Setting
Recall
Label
Darkness
Speed
Media
Type
X-Offset
LCD
Language
Device
Dump Mode
Wizard
Continuous
Codepage
10
6
0
Printer
Control
Tap‘’Main ‘’--
Screen could show more detail of‘’ Main‘’
Tap‘’Wizard ‘’--
Set up printer of ‘’Darkness’’ ‘’Speed ‘’...
Main
Main
Wizard
ZX1200 V2.0000
Wizard
Test
Test
Y-Offset
0
Test
Self-Test page
Out of Dump Mode
18
Tap‘’Test ‘’--
self-Test page and Out of Dump Mode for setting.
Page 23
3 Printer Setting and Control
Darkness
Speed
Sensor
Select
Media
Type
Darkness
Printer Settings
10
6
Auto Select
Continuous
Printer Settings
10
finish setting tap
back to main page if
do not save, tap
system would not save
any changes.
UNLOCK
LOCK
Printer
Setting
Label
Setting
Recall
Label
Main
LCD
Language
Device
Dump Mode
Codepage
Printer
Control
Speed
Sensor
Select
Media
Type
6
Auto Select
Continuous
If printer functions locked, printer can not receive any commands
from GoLabel or any devices.
19
Page 24
3 Printer Setting and Control
Keyboard Mode
When plug-in an USB keyboard to the printer, LCD touch panel will display “Enter Standalone”, press the “Y” key
on keyboard to entering to the dialog for “Keyboard Mode” operation.
Keyboard Mode
ZX1200 V2.0000
Enter Standalone
(Y/N)
Recall
Label
Clock
Setting
Country
Code
Database
Setting
Codepage
Label
Edit
Preview Label function
User can choose any labels which have done in the printer and preview it. (See Instuctions)
ZX1200 V2.0000
Printer
From the Home screen, tap
to Main Page.
Main
From the Main Page tap Recall Label
to Recall Label Page.
Setting
Label
Setting
Main
LCD
Language
Device
Codepage
Printer
Control
Main
Wizard
20
Test
Recall
Label
Dump Mode
Page 25
3 Printer Setting and Control
Recall Label
001/002 FORM NAME
LABEL-1
LABEL-2
Preview
Label
Recall Label
From the Recall Label Page
5
5
0
ZX1230i
5
5
0
the touch panel shown on all labels,
Tap up to choose labels.
FW:V2.000
15
0
15
0
Preview
Label
Tap down to choose labels.
Tap Preview Label can see printing label.
Preview
Label
Recall Label
Recall Label
Keeping tap to next page
ZX1200i
FW:V2.000
Prompt
001
Print Quantity
1
Print out selected label.
5
****Using recall label function send commands, printer display must be back to Ready Page.
21
ZX1200 V2.0000
Main
Test
Wizard
Page 26
3 Printer Setting and Control
3.3 LCD Interface Function
Main Page
Main
Printer
Setting
Label
Setting
Recall
Label
LCD
Language
Device
Dump Mode
Setting items for printer, ex. Printing speed, darkness.Also includes a Printing Wizard for your ease of printing.
More than 10 languages for printer sett ing
It consists of a table of values that describes the character set for a particular language
Setting items for printing label, ex. Rotat ion, Printing position offset.
Codepage
Printer
Control
Option modules and connection port settings.
Self-Diagnose functions for printer,
Recall Label
Dump Mode
ex. TPH testing, self-test page printing.
22
Page 27
3 Printer Setting and Control
Device Page
Device
Device
Buzzer
Serial Port
Setting
Clock
Setting
Option Setting
LAN
Setting
Setting off or on for buzzer
Setting items for options, ex. Cutt er, Label Dispenser, Applicat or
Choose ON. Printing labels would be back to start position.
Setting items for Serial Port, ex. Baud Rate, Parity, Data Bits, Stop Bits.
Smart
Backfeed
LCD
Setting
Setting items for LAN, ex. Port NO., DHCP, Dynamic IP, Default Gat eway, Subnet Mask.
Setting items for LCD, ex. Brightness, Contrast, Power Saving, Password
Setting items for Clo
ck, ex. Year, Month, Day, Hour, Minute
23
Page 28
3 Printer Setting and Control
Darkness
0-19
Speed
2-5
Auto Select
See-Through
Reflective
Label with Gaps
Label with Marks
Continuous
Direct Thermal
Thermat Transfer
Tear-off Position
0-40
Apply
Cancel
English
Deutsch
繁體中文
Français
Español
日本語
Italiano
Pусский
Türkçe
850
852
437
860
863
865
857
861
862
855
866
737
851
869
Win 1252
Win 1250
Win 1251
Win 1253
Win 1254
Win 1255
Win 1257
Rotation
X-offset
Y-offset
Start Offset
Setting Items in Setting Mode
Media Detection
Sensor Select
Printer Setting
LCD Language
Media Type
Printing Mode
Top of Form
簡體中文
Codepage
Label Setting
24
Page 29
3 Printer Setting and Control
OFF
ON
None
Cutter
Label Dispenser
Applicator
Off
On
4800 bps
9600 bps
19200 bps
38400 bps
57600 bps
115200 bps
Non
Odd
Even
7 bits
8 bits
1 bits
2 bits
DHCP
On
IP Address
0.0.0.0
Subnet Mask
255.255.255.0
Gatway
192.168.0.254
Brightness
5
Contrast
5
Power Saving
15
Password
OFF
Year
Month
day
Hour
Minute
Test
Sample Pattern
Select Memory
Clear Memory
Calibration
Reset to Default
Darkness
2-5 or 7
Speed
0-19
Label with Gaps
Label with Marks
Continuous
X-Offset
Y-Offset
Enable
Disable
Enable
Disable
Enable
Disable
PIN Code
0000
Search Devices
Self-Test page
Out of Dump Mode
Device
Buzzer
Optional Setting
Smart Backfeed
Baud Rate
Serial Port Setting
Parity
Data bits
Stop bits
Printer Control
Wizard
LAN Setting
LCD Setting
Clock Setting
Media Type
Clear Bind
Make Device Visible
Bluetooth
SSP
Test
25
Page 30
3 Printer Setting and Control
Appears on the NAVIGATION ICON of Setting
touching display upper right icon.
Appears on the NAVIGATION ICON of Setting
On Setting Value pages, touch display icons to
change.
Status of LCD Interface
When printer is on standby status (ready to print), the LCD interface will display “Ready” on screen.
You can only print when you see the “Ready“ status.
ZX1200 V2.0000
Main
If there is any printers error, the LCD screen will display the error screen to show the type of error.
You can fix the error according the notice.
WARNING ICON
Icon Definition
Wizard
To upper level
Test
ERROR ICON
ERROR DESCRIPTION
Pages. It guides you back to upper level by
To main page
Lock
Unlock
Value Pages. It guides you back to main page by touching display upper left icon.
lock the value for preventing unexpected
Touch display icons again to unlock the value.
26
Page 31
3 Printer Setting and Control
3.4 Label Calibration and Self Test
Label Calibration
The printer can automatically detect and store label height.
That means the host computer does not need to transmit the label height to the printer.
Self Test
Self-test function lets you check whether the printer is functioning normally.
Here is how you run the label size calibration and self test.
1. Check that the label stock is loaded correctly.
2. Turn off the printer.
3. Turn the printer on again, keeping the FEED button pressed. When the LED starts to flash red, release the FEED
button. The printer will now measure the label stock and store the label height.
4. Once the printer has successfully measured the label stock, it will print a self-test label.
The contents of a self-test printout are listed below.
Model & Version
USB ID setting
Serial port setting
MAC address of Ethernet port
IP protocol setting
IP address of Ethernet port
Gateway setting
Netmask setting
Number of DRAM installed
Image buffer size
Number of forms
Number of graphics
Number of fonts
Number of Asian fonts
Number of Databases
Number of Scalable fonts
Free memory size
Speed, Density, Ref. Point, Print direction
Label width, Form length, Stop position
Cutter, Label Dispenser, Mode
Sensor Setting
Code Page
ZX1200i:GX.XXX
USB S/N:12345678
Serial port:96,N,8,1
MAC Addr:xx-xx-xx-xx-xx-xx
DHCP Enable
IP xxx.xxx.xxx.xxx
Gateway xxx.xxx.xxx.xxx
Sub-Mask xxx.xxx.xxx.xxx
##################################
1 DRAM installed
Image buffer size:1500 KB
0000 FORM(S) IN MEMORY
0000 GRAPHIC(S) IN MEMORY
000 FONT(S) IN MEMORY
000 ASIAN FONT(S) IN MEMORY
000 DATABASE(S) IN MEMORY
000 TTF(S) IN MEMORY
4073 KB FREE MEMORY
^S4 ^H8 ^R000 ~R200
^W102 ^Q100,3 ^E18
Option:^D0 ^O0 ^AD
Reflective AD:1.96 2.84 2.49[0.88_23]
Code Page:850
27
Page 32
3 Printer Setting and Control
Label Calibration Button
A hardware button to make a Label Calibration while printer encountering ‘’Media Error’’ during the cases when first-time
printer start up or change label or ribbon to another type, such as change using gap label to continuous or black mark
labels.
Press
CALIBRATION BUTTON
Press C-button for 2 seconds, it will make an auto-sensing to calibrate the label and ribbon’s parameters.
Press
****Press C-button is equivalent to the auto-sensing command ‘’~S,SENSOR’’ that will cancel on-printing-job and make the
Label Calibration immediately.
28
Page 33
3 Printer Setting and Control
Operation Panel
Status
3.5 Error Alerts
In the event of a problem that prevents normal functioning of the printer, you will see an error message on LCD
screen and hear some beep signals. Please refer to below table for the error alerts.
OPERATION TOUCH PANEL
Type Beeps Description Solution
Print Head Error 2 x 4 beeps
The printing
mechanism is not
correctly closed.
Open the print
mechanism and
close it again.
LCD TOUCH PANEL
FEED BUTTON
POWER BUTTON
Check ribbon
Print Head Error None
Media Error 2 x 3 beeps
29
High temperature
at the print head.
No ribbon is
installed and the
printer displays an
error.
The ribbon is
fini
shed or the
label supply hub is
not mov ing.
Once the print
head has cooled
down, the printer
switches to
standby mode.
Make sure that
the printer is set to
direct thermal
printing mode.
Replace the
ribbon roll.
Page 34
3 Printer Setting and Control
Operation Panel
Status
Possible reasons:
Use the "~X4"
correct.
Satus Beeps Description Solution
Media Error 2 x 2 beeps
No paper is
detected.
Paper is finished.
Printer feed
problem.
Make sure that
the label sensor is
positioned
correctly. If the
sensor still does not
detect the paper,
run the auto-
detection
function again.
Replace the label
roll.
the print medium
has become
trapped around
the rubber roll; the
sensor cannot
detect a gap or
black mark
betw een the
labels; there is no
paper. Please
reset the sensor.
File Error 2 x 2 beeps
The memory is full.
The printer prints
the message "File
System full ".
Unable to find file.
The printer prints
the message "File
Name not found"
A file of the same
name already
exists. The printer
prints the message
"Duplicate Name".
Delete
unnecessary data
or install
additional
memory.
command to print
all files. Then
check whether
the files exist and
whether the
names are
Change the
name of the file
and try storing it
again.
30
Page 35
3 Printer Setting and Control
3.6 USB Host
Definition : USB Host port supports either deviceUSB memory stick, keyboard or scanner.
Purpose
USB memory stick : It extends the user memory space up to 32GB for Graphic, Font, Label Format, DBF and Command
files downloading. The printer’s Firmware also can be updating if copy new version of Firmware into USB memory stick.
Connecting an USB keyboard to printer for ‘’Keyboard Mode’’ mode operation.
Plug-in an USB scanner to operate the printer in ‘’Keyboard Mode’’ .
Usage of Extended Memory
USB memory stick : It supports hot-plugging function; printer will create a Folder ‘’\LABELDIR’’ and switch ‘’User Flash’’
to ‘’ Extended Memory‘’ automatically while user plugs an USB memory stick into a GoDEX printer.
Connect the USB Stick plugged -in printer to PC via USB Device or Ethernet port and run ‘’GoLabel’’ software to
download Graphic, Font, Label Format, DBF and Command files to the printer.
Detail download procedures, please refer to ‘’GoLabel On-line Help’’.
Usage of Firmware Update
Remove USB memory stick from printer and plug-in it to a PC’s USB port; delete Firmware ‘’*.bin’’ file from
‘’\LABELDIR\FW’’ of USB memory stick if it existing; or create a Folder ‘’\LABELDIR\FW’’ to USB memory stick if it doesn’t
existing.
Copy a new version of Firmware ‘’xxxx.bin’’ to the Folder ‘’\LABELDIR\FW’’; and then remove USB and plug-in
back to the printer that going to update Firmware.
The printer will update the Firmware automatically when plug-it-into the printer and printer find-out the Firmware
in ‘’\LABELDIR\FW’’ is newer version.
Don’t remove the USB memory stick out while it’s under updating with ‘’Flash Writing...’’message that displays on
LCD panel.
31
Page 36
3 Printer Setting and Control
USB Keyboard
When plug-in an USB keyboard to the printer, LCD touch panel will display “Enter Standalone”, press the
“Y” key on keyboard to entering to the dialog for “Keyboard Mode” operation.
Here have six sub-dialogs “Recall Label” “Country Code” “Code Page” “Clock Setting” “Database Setting”
“Label Edit” is able operating by keyboard as follow definition:
1. Press “ESC” key to exist from “
2. Press “F1”, it will let the printer from “Home Page” mode entering into “Keyboard Mode”
3. Press “Enter”, “Arrow” and “Alphabetic” keys as the usual in PC that will perform the key-in function of
“Keyboard Mode”.
Scanner
When plug-in an USB scanner to the printer, LCD touch panel will display “Enter Standalone”, tap the “Y” to
entering the dialog of “Keyboard Mode” operation.
Scanner is using in “Keyboard Mode” to scanning the “Serial Number, Variable” and Print Quantity while the printer
prompts a message on LCD touch panel and wait for data input.
Keyboard Mode
” or back to previous dialog
** The USB Host port on GoDEX printer is without ‘’HUB’’ function.
** The USB Memory Stick supports with ‘’FAT32’’Disk Format and up to 32GB only. The certified venders are Transcend,
Apacer, Patriot, Consair and Kingston.
* The download function for Graphic, Font, Label Format, DBF and Command files is operated by GoLabel of PC and
must go through the a ‘’i’’ ‘’x’’ model printer itself.
* On a PC, user may copy entire folder’’\LABELDIR’’ from USB memory stick to PC or vice-versa. Copy a sub-folder or
individual file in ‘’\LABELDIR’’ to PC or vice-versa is not supported.
32
Page 37
4 NetSetting for Ethernet
4.1 Installing the NetSetting software
The NetSetting software is used to manage the network configurations when connecting the printer via Ethernet port.
It is available on product CD or can be downloaded from official website. To install the NetSetting, please follow
below steps.
1. Insert the product CD in the CD/DVD drive of the host computer and open the "Ethernet" folder on the CD.
2. Select the icon for the NetSetting installation file and click it to start the installation.
3. Follow the instructions on the screen. The Setup Wizard guides you through the installation procedure.
4. Specify the “Installation Folder".
5. Click ”Next” to start the installation.
6. Once the installation is completed; you will see the NetSetting icon on your desktop.
33
Page 38
4 NetSetting for Ethernet
4.2 The Interface of NetSetting
Click the NetSetting icon to start the program; you will see the start page as below. The start page will display the
basic information of connected printer and your PC.
ZX1200
Click the magnifier icon to search the Godex printers which are connected via Ethernet port in you network
environment. Once a connected Godex printer is detected, it will be listed on the start page.
There are six tabs on the top of interface which can configure different types of network settings. But for the data
security reason, you need correct password to enter the configuration pages.
**** The default password is “1111”, you can change the password later from the “IP Setting” tab.
34
Page 39
4 NetSetting for Ethernet
IP Setting
The IP Setting tab can change the printer name, Port number, Gateway setting and the password for configuring the
printer. You can also set the printer’s IP address ether by DHCP or by Static IP.
You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.
**** To fully benefit from the NetSetting software, you should be familiar with basic networking principles. Please
contact your network administrator for related network setting information.
35
Page 40
4 NetSetting for Ethernet
Alert Path Setting
NetSetting will send the alert messages to designated mail account when the error happened on printer. The alert
messages are sent by SMTP (Simple Mail Transfer Protocol) or SNMP (Simple Network Management Protocol).
You can set or change the configurations of SMTP and SNMP on this “Alert Path Setting” tab.
You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.
36
Page 41
4 NetSetting for Ethernet
Alert Message Setting
For the alert message notification function, you can decide which error cases need to be sent out to the operator.
Moreover, the alert messages can be set to be sent by SMTP, SNMP or both.
You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.
37
Page 42
4 NetSetting for Ethernet
Printer Configuration
Set or change the configurations of connected printer. Most of key settings for the printer operation can be done
by this setting page.
ZX1200i
You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.
38
Page 43
4 NetSetting for Ethernet
User Command
The “User Command” tab provides a communication interface for operator to control the printer. Input printer
commands in "Input Command" window and press “Send Command” button, the commands will be sent to the
printer.
For some commands that will return response message, the message will be displayed in "Output Message" window.
You can press “Send Command” button to send printer commands via Ethernet port and control the printer
remotely.
39
Page 44
4 NetSetting for Ethernet
Firmware Download
On “Firmware Download” tab, the current version of printer firmware will be showed on the screen. If you need to
update the printer firmware, just specify the file location of firmware file and press “Start Download Firmware” button.
The printer firmware then can be updated remotely.
BOOT : 1.000a1 F/W : ZX1200i 1.000a
In addition to the firmware update, you can press “Recover To Factory Settings” button to restore the printer
configurations back to factory default.
40
Page 45
5 Accessories5 Accessories
5.1 Preparation Steps
Before installing the optional modules, please make some preparations as follows.
1. Turn off the printer :
Remember to switch off the printer before installing any module.
2. Open the printer cover
Place the printer on a flat surface and open the printer cove
**** Remember to switch off the printer before installing the cutter.
**** Do not use to cut adhesive labels! Glue residue will be left on the cutter blade and impair its functioning.
**** Under the ordinary paper application condition, the cutter performs 300000 cuts of a heavy paper with up
to 250 μm thick or 100000 cuts of a plastic sheet with up to 300 μm thick.
41
Page 46
5 Accessories
5.2 Installing the Cutter
The Overview of the Cutter
1.Cutter module
2. Screw
Unscrew the screw marked in the illustration on the front of the printer, which secures the lower cover plate.
Remove lower cover plate to the a little bit right then can get out.
1
2
42
Page 47
5 Accessories
Connect the cutter cable connector to the cutter jack on the printer.
43
Be sure the cutter module insert to printer properly. (see red arrow)
Page 48
5 Accessories
Secure the cutter module on the printer housing using the screws.
Finish the cutter module installed.
Now load the label roll into the printer and close the printer cover.
**** Check whether the cutter function is enabled in the printer.
**** Labels or paper should be at least 30 mm high.
**** After installation of the cutter module, set the stop position (^E) to 30.
44
Page 49
5 Accessories
5.2 Option Rewind Ribbon Hub Removing Ribbon
Use tool to cut off the ribbon.
45
Page 50
5 Accessories
Pull open the knob, ribbon could be easy to remove.
46
Page 51
6 Maintenance and Adjustment
6.1 Installing / removing the print head module
Open the printer cover.
using a screwdriver or a coin, loosen the screw to take out the TPH module.
$
Turn the print head counterclockwise to a top right position
Hold the print head module , pull out the TPH cable smoothly. To install TPH module, follow the reverse order.
Note
* Remember to switch off the printer before removing the print head module.
47
Page 52
6 Maintenance and Adjustment
6.2 Adjusting the print line
Open the printer cover.
using a screwdriver or a coin to loosen the screw
$
indicator board
Turn the print head counterclockwise to a top right position
If no improvement is visible, turn the
screws(A) clockwise or counterclockwise
as far as possible and be sure to align with
the indicator board and indicator line.
Repeat the adjustment process until printing
quality has improved.
indicator line
A A
48
Page 53
6 Maintenance and Adjustment
1
1
2
3
4
2
2
3
3
4
4
1
1
1
6.3 Adjusting ribbon tension
You can adjust the ribbon tension by turning the ribbon shaft knob (see illustration) clockwise or counterclockwise.
There are 4 possible settings, which is marked on the ribbon supply hub.
# 1 : Tension is the highest
# 4 : Tension is the lowest
If the tension is so low that the ribbon does not move forward, you need to reduce the tension of the ribbon supply hub.
To set the tension, press in the knob and turn it clockwise or counterclockwise as required.
Increasing the tension of the ribbon rewind hub will remove any wrinkling of the ribbon during printing,
which results from the use of different ribbon materials. (For details about the wrinkling/creasing of ribbons,
see Section 6-6.)
If you are using a very narrow ribbon, the printer may not move the label stock forward (particularly with
a ribbon that is less than 2" wide). In that case, reduce the tension by turning the knob of the ribbon supply hub
counterclockwise.
49
Page 54
6 Maintenance and Adjustment
6.4 Cleaning the thermal print head
Dirt on the print head or ribbon may result in inadequate print quality (there are only partial images on the label). The printer cover should therefore be kept closed when possible. Keeping dirt and dust away from the paper or labels ensures a good print quality and a longer lifespan of the print head. Here is how you clean the print head:
1. Switch off the printer.
2. Open the printer cover.
3. Remove the ribbon.
4. Release the print head by turning the print head release lever.
5. To remove any label residue or other dirt from the print head (see Red arrow), please use a soft lint-free cloth dipped in alcohol to wipe.
Note
* The print head should be cleaned once a week.
**Please make sure that there are no metal fragments or other hard particles on the soft cloth used to clean
the print head.
50
Page 55
6 Maintenance and Adjustment
6.5 Adjusting the balance and print head tension
Open the printer cover.
using a screwdriver or a coin to loosen the screw
$
When using a variety of label stock
and ribbons, the ink may not be evenly distributed.
If there is no printed image on one side of the paper
, or the ribbon wrinkles, the print head pressure
must be readjusted using the TPH spring boxes.
Move the TPH spring boxes as shown in the illustration
to change the print head pressure.
The wider the label you are using, the further apart
the TPH spring boxes must be moved away from
each other. If there is no quality improvement,
you need to change the pressure on the TPH spring boxes.
Reset Mark (A) Mark (B)
Turning the screw left increases the pressure,
while turning it right reduces the pressure.
Be sure not to turn the screw so that it goes below Mark(B).
51
Page 56
6 Maintenance and Adjustment
6.6 Ribbon shield settings
The use of different ribbon materials may cause wrinkling of the ribbon, which in turn affects the print result
as illustrated by the examples in (a) and (b). To change the print quality, you can adjust the ribbon shield screws.
If your print result looks like the example in (a), you need to turn ribbon shield screw clockwise.
If your print result looks like the example in (b), you need to turn ribbon shield screw counterclockwise.
(a) (b)
To keep track of the change in print quality, you should adjust the screws by half a turn at a time.
Print a test page. If there is no improvement in the print result, turn the screw by another half turn.
o
Do not turn the adjustment screw more than two full turns(360
Reset Mark
).
Note
* If you adjust the screw by more than two full turns, the paper feed may no longer function correctly. In that case, unscrew the ribbon shield screws to align the reset mark and restart the adjustment process.
52
Page 57
6 Maintenance and Adjustment
6.7 Cutter settings
Switch off the printer before removing
the CUTTER.
(remove or install cutter refer to ‘’accessories’’ in Section 5)
Unscrew the screw at the bottom of cutter .
Remove the cutter cover. Clean and remove jammed paper. Reinstall CUTTER back onto printer.
Note
* Remember to switch off the printer before removing the CUTTER.
**The label medium should be at least 30 mm long to ensure correct functioning of the cutter.
53
Page 58
6 Maintenance and Adjustment
ermal
6.8 Troubleshooting
Problem Solution
The printer is switched on but the LED does not light up.
The LED lights up red and printing is interrupted.
The label stock passes through the printer but no image is printed.
The label stock jams during printing.
There is no printed image on some parts of the label.
There is no printed image on part of the label or the image is blurred.
Check the power supply.
Please see the Section 2.4
Check the software settings (driver settings) or command codes. Look for the error alert in the table in Section 3.3. Error Alerts. Check whether the print mechanism is closed correctly.
Please see the Section 3.3
Please make sure that the label stock is loaded the right side up
and that it is the suitable material.
Choose the correct printer driver. Choose the correct label stock and a suitable printing mode.
Clear the paper jam. Remove any label material left on the
thermal print head and clean the print head using a soft lint-free cloth dipped in alcohol.
Please see the Section 6.1
Check whether there is any label material or ribbon stuck to the th
print head.
Check for errors in the application software. Check whether the starting position has been set correctly. Check the ribbon for wrinkles.
Check the thermal print head for dust or other dirt. Use the internal “~T” command to check whether the thermal print
head will carry out a complete print job.
Check the quality of the print medium.
The printed image is positioned incorrectly.
Skipping labels during printing.
The printed image is blurred.
The cutter does not cut off the labels in a straight line.
The cutter does not cut off the labels completely.
When using the cutter, the labels are not fed through or cut off incorrectly.
The label dispenser is not functioning normally.
Check whether there is paper or dust covering the sensor. Check whether the label stock is suitable. Contact your supplier. Check the paper guide settings.
Check the label height setting. Check whether there is dust covering the sensor. Run the auto-detection function.
Please see the Section 3.2
Check the darkness setting. Check the thermal print head for dust or dirt.
Please see the Section 6.1
Check whether the label stock is positioned straight.
Check whether the label is more than 0.2 mm thick.
Check whether the cutter has been correctly installed. Check whether the paper guides are functioning correctly.
Check whether there is dust on the label dispenser. Check whether the label stock is positioned correctly.
Note
**** If any problems occur that are not described above, please contact your dealer.
54
Page 59
ZX1200i/ZX1300i/ZX1600
variables such as label type, thickness, spacing, liner construction, etc. Godex is pleased to test non
USER MANUAL
APPENDIX
PRODUCT SPECIFICATIONS
i
Notice
Specifications are subject to change without notice. All company and/or product names are trademarks and/or registered
trademarks of their respective owners.
** Minimum print height and maximum print speed specification compliance can be dependent on non
Appendix
Page 60
Default settings:
Baud rate 9600, no parity, 8 data bits, 1 stop bit, XON/XOFF
RS232 Housing(9-pin to 9-pin)
DB9 Socket
DB9 Plug
Handshaking
:
DSTB is sent to the printer, BUSY to the host computer
Interface cable
Pin No.
Function
Transmitter
1
36
/Strobe
/Select-in
Computer / printer
Computer / printer
ZX1200i/ZX1300i/ZX1600
USER MANUAL
APPENDIX
INTERFACE
Parallel port
: Parallel cable compatible with IBM computers
i
Pinout :
2-9 10 11 12 13 14 15 16 17 18 19-30 31 32 33 34-35
Serial Port
See below
Data 0-7 /Acknowledge Busy /Paper empty /Select /Auto-Linefeed N/C Signal Gnd Chassis Gnd +5V, max 500mA Signal Gnd /Initialize /Error Signal Ground N/C
protocol and RTS/CTS
Computer Printer Printer Printer Printer Computer / printer
Computer Computer / printer Printer
-
RXD
TXD DTR
GND
DSR
RTS
CTS
****The total current to the serial port may not exceed 500mA.
RI
Computer
1 2 3 4 5 6 7 8 9
Appendix
+5V, max 500mA
1 2 3 4 5 6 7 8 9
TXD RXD N/C
GND
RTS
CTS
RTS
N/C
Printer
Page 61
Pin NO. 1 2 3 4
Function
VBUS
D-
D+
GND
Pin NO. 1 2 3 4
Function
VBUS
D-
D+
GND
PIN NO.
FUNCTION
2
T-
3
R+
4
N/C
5
N/C 6 R-
7
N/C
8
N/C
PIN NO.
FUNCTION
5
PAUSE
7
+24V,max 1.5A
8
GND
10
SERV_REQ
12
MEDIA_OUT
13
RIBBON_OUT
14
DATA_READY
15
OPT_FAULT
APPENDIX
USB Port
Ethernet (RJ-45)
ZX1200i/ZX1300i/ZX1600
USER MANUAL
INTERFACE
Computer Connector : Type A:
Connector Type : Type B
i
1 T+
Applicator
1 GND
2 +5V,max 500mA
3 START_PNT
4 SLEW_LABEL
6 REPRINT
9 RIBBON_LOW
11 END_PRINT
Appendix
Loading...