GIGABYTE GA-6PXSV2 Owner's Manual

GA-6PXSV2
GA-6PXSV3

LGA 2011 socket motherboard for Intel® E5-1600/E5-2600 series
processors

User's Manual

Rev. 1001

Copyright

© 2012 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specifications and features in this manual may be made by GIGABYTE

without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of documentations:

 For quick set-up of the product, read the Quick Installation Guide included with the product.
 For detailed product information, carefully read the User's Manual.

For product-related information, check on our website at:

http://www.gigabyte.com

Table of Contents

Box Contents ...................................................................................................................5

GA-6PXSV2/GA-6PXSV3 Motherboard Layout ..............................................................6

Chapter 1 Hardware Installation .....................................................................................9

1-1 Installation Precautions .................................................................................... 9

1-2 ProductSpecications .................................................................................... 10

1-3 Installing the CPU and CPU Cooler ............................................................... 12

1-3-1 Installing the CPU ...................................................................................................12

1-4 Installing the Memory ..................................................................................... 14

1-4-1 FourChannelMemoryConguration .....................................................................14

1-4-2 Installing a Memory ...............................................................................................15

1-4-3 DIMM Population Table .........................................................................................15

1-5 Back Panel Connectors .................................................................................. 16

1-6 Internal Connectors ........................................................................................ 18

Chapter 2 BIOS Setup ..................................................................................................33

2-1 The Main Menu .............................................................................................. 35

2-2 Advanced Menu ............................................................................................. 37

2-2-1 PCIConguration ...................................................................................................38

2-2-2 Trusted Computing .................................................................................................39

2-2-3 CPUConguration ..................................................................................................40

2-2-4 Runtime Error Logging ...........................................................................................44

2-2-5 SATAConguration.................................................................................................45

2-2-6 SuperIOConguration ...........................................................................................46

2-2-7 Serial Port Console Redirection .............................................................................48

2-3 Chipset Menu ................................................................................................. 51

2-3-1 NorthBridgeConguration .....................................................................................52

2-3-1-1 IOHConguration ...................................................................................................54

2-3-1-2 DIMM Information ...................................................................................................56

2-3-2 SouthBridgeConguration ....................................................................................57

2-3-3 ME Subsystem .......................................................................................................59

2-4 Security Menu ................................................................................................ 60

2-5 Server Management Menu ............................................................................. 61

2-5-1 System Information .................................................................................................62

2-5-2 BMCLANConguration .........................................................................................63

2-6 Boot Option Menu .......................................................................................... 64

2-7 Boot Manager ................................................................................................. 66

2-8 Exit Menu ....................................................................................................... 67

- 3 -

Chapter 3 Appendix ......................................................................................................69

3-1 Regulatory Statements ................................................................................... 69

- 4 -

Box Contents

GA-6PXSV2/GA-6PXSV3 motherboard

Driver CD

Two SATA cables

I/O Shield

• The box contents above are for reference only and the actual items shall depend on the product package you obtain.

The box contents are subject to change without notice.

• The motherboard image is for reference only.

- 5 -

GA-6PXSV2/GA-6PXSV3 Motherboard Layout

36

35

34

33

32

31

30

29
28

27

3837 40

39

25

26

24

41 42

23

22

43

44

20

45

1921

1

18

3 4 5 6

2

13
14
15
16

7
8
9

10

11

12

17

- 6 -

Item Code Description

1 AUDIO1 Audio jacks
2 MLAN1 BMC Management LAN port

(GA-6PXSV3)

USB_MLAN BMC Management LAN port and USB

connectors (GA-6PXSV2)
3 USB_LAN2 LAN connector and USB connectors
4 USB_LAN1 LAN connector and USB connectors
5 R_USB1 USB connectors (GA-6PXSV3 Only)
6 COM1_VGA1 Serial port and VGA port
7 DDR3_P0_A0 DIMM slot (channel A-0)
8 DDR3_P0_A1 DIMM slot (channel A-1)
9 DDR3_P0_B0 DIMM slot (channel B-0 )

10 DDR3_P0_B1 DIMM slot (channel B-1 )
11 P2_CPU 8 pin power connector
12 CPU0 Intel LGA 2011 socket
13 DDR3_P0_D1 DIMM slot (channel D-1 )
14 DDR3_P0_D0 DIMM slot (channel D-0 )
15 DDR3_P0_C1 DIMM slot (channel C-1 )
16 DDR3_P0_C0 DIMM slot (channel C-0 )
17 PWR_DET1 PMBus connector
18 P1 24 pin power connector
19 SYS_FAN2 System fan cable connectors
20 SATA_SGPIO SATA SGPIO connector
21 SATA01 SATA 6Gb/s connectors
22 SATA2345 SATA 3Gb/s connectors
23 BAT1 Battery socket
24 PASSWORD1 Clear password jumper
25 CLR_CMOS1 Clear CMOS jumper
26 F_PANEL1 Front panel connector
27 SYS_FAN3 System fan cable connectors
28 SAS0_3 Mini SAS connector
29 BMC_FRB1 Force to Stop FRB3 Timer jumper
30 F_USB3_2 Front USB 3.0 connector
31 BIOS_RCVR BIOS recovery jumper
32 F_USB3_1 Front USB 3.0 connector
33 BIOS_WP BIOS write protect jumper
34 TPM TPM module
35 F_USB1 Front USB connector

(GA-6PXSV2 Only)

36 COM2 Serial cable connector

- 7 -

37 PCIE4 PCI-E slot 4 (x4 slot/Gen2/running x1/

GA-6PXSV2)
PCI-E slot 4 (x4 slot/Gen2/running x2/

GA-6PXSV3)

38 BMC_LED1 BMC Firmware Readiness LED
39 PCIE3 PCI-E slot 3

(x8 slot/Gen3/Shared bandwidth with

PCI-E slot 2/GA-6PXSV2 Only)

40 PCIE2 PCI-E slot 2

(x16 slot/Gen3/Shared bandwidth with

PCI-E slot 3/GA-6PXSV2)
PCI-E slot 2

(x16 slot/Gen3/GA-6PXSV3)

41 SSB_ME1 ME recovery jumper
42 SPDIF_IN S/PDIF header
43 SYS_FAN1 System fan cable connector
44 PCIE1 PCI-E slot 1 (x16 slot/Gen3)
45 CPU_FAN1 CPU fan cable connector

- 8 -

Hardware Installation

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can

become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read

the user's manual and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic com-

ponents such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,

keep your hands dry and rst touch a metal object to eliminate static electricity.

• Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power sup-

ply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your hard-

ware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to sys-

tem components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

.

- 9 -

Hardware Installation

1-2 ProductSpecications

CPU  Support for Intel® Xeon® E5 series processors in the LGA2011 package

 L3 cache varies with CPU

Chipset  Intel® BD82C604 (X79) PCH

Memory  8 x 1.5V DDR3 DIMM sockets supporting up to 64GB (UDIMM) and

256GB (RDIMM) of system memory

* Due to Windows 32-bit operating system limitation, when more than 4 GB of physical

LAN  2 x Intel® 82574 supports 10/100/10 00 Mbps

Expansion Slots  1 x PCI Express x16 slot, running at x16 (Gen3/PCIE1)

Onboard Audio  REALTEK® ACL892 HD

Storage Interface  2 x SATA 6Gb/s connectors (SATA0/1)

USB
(onboard
header)

Internal
Connectors

memory is installed, the actual memory size displayed will be less than 4 GB.

 Four channel memory architecture
 Support for 1600/1033/1066 memory modules
 Support for ECC memory modules

 1 x PCI Express x16 slot, running at x16 (Gen3/PCIE2/GA-6PXSV3)
 1 x PCI Express x16 slot, running at x16 (Gen3/Shared bandwidth with

PCI-E slot 3/GA-6PXSV2)

 1 x PCI Express x8 slot, running at x8 (Gen3/Shared bandwidth with

PCI-E slot 2/GA-6PXSV2)
 1 x PCI Express x4 slot, running at x1 (Gen2/PCIE4/GA-6PXSV2)
 1 x PCI Express x4 slot, running at x2 (Gen2/PCIE4/GA-6PXSV3)

 4 x SATA 3Gb/s connectors (SATA2/3/4/5)
 1 x SAS 3Gb/s connector (SAS0_3)
 Support for Intel RSTe SATA RAID 0, RAID 1, RAID 10, RAID 5
 2 x USB 2.0/1.1 ports (GA-6PXSV2 Only)
 Up to 4 USB 3.0 ports (4 via the USB brackets connected to the internal USB

headers)

 1 x 24-pin ATX main power connector
 1 x 8-pin ATX 12V power connector
 4 x SATA 3Gb/s connectors
 2 x SATA 6Gb/s connectors
 1 x SAS 3Gb/s connector
 1 x CPU fan header
 3 x System fan header
 1 x front panel header
 2 x USB3.0 headers
 1 x USB2.0 header (GA-6PXSV2 Only)
 1 x TPM header
 1 x serial port header
 1 x PMBus header

- 10 -

Hardware Installation

Back Panel
Connectors

 6 x USB 2.0/1.1 ports (GA-6PXSV3)
 4 x USB 3.0 ports (GA-6PXSV2)
 2 x USB 2.0/1.1 ports (GA-6PXSV2)
 2 x RJ-45 LAN ports
 1 x 10/100 Management LAN port
 6 x Audio ports (4 x Line-out/1 x Line-in/1 x MIC)
 1 x COM port
 1 x VGA port

I/O Controller  iTE IT8728 chip

Hardware
Monitor

 System voltage detection
 CPU/System temperature detection
 CPU/System/Power fan speed detection
 CPU overheating warning
 CPU/System/Power fan fail warning
 CPU/System fan speed control

* Whether the CPU/system fan speed control function is supported will depend on

the CPU/system cooler you install.

BIOS  1 x 64 Mbit ash

 AMI BIOS

Form Factor  ATX Form Factor; 12 inch x 9.6 inch

* GIGABYTE reserves the right to make any changes to the product specications and product-related information

without prior notice.

- 11 -

Hardware Installation

1-3 Installing the CPU and CPU Cooler

Read the following guidelines before you begin to install the CPU:

• Make sure that the motherboard supports the CPU.
(Go to GIGABYTE's website for the latest CPU support list.)

• Always turn off the computer and unplug the power cord from the power outlet before installing
the CPU to prevent hardware damage.

• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

• Apply an even and thin layer of thermal grease on the surface of the CPU.

• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and dam-

age of the CPU may occur.

• Set the CPU host frequency in accordance with the CPU specications. It is not recommended
that the system bus frequency be set beyond hardware specications since it does not meet the

standard requirements for the peripherals. If you wish to set the frequency beyond the standard
specications, please do so according to your hardware specications including the CPU, graph­ics card, memory, hard drive, etc.

1-3-1 Installing the CPU

A. Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

Pin One Corner of the CPU

Socket

- 12 -

Alignment Key

LGA2011 CPU

Notch

Notch

Alignment Key

Notch

Notch

Triangle Pin One Marking on

the CPU

Hardware Installation

B. Follow the steps below to correctly install the CPU into the motherboard CPU socket.

• Before installing the CPU, make sure to turn off the computer and unplug the power cord
from the power outlet to prevent damage to the CPU.

• To protect the socket contacts, do not remove the protective plastic cover unless the CPU is
inserted into the CPU socket. Save the cover properly and replace it if the CPU is removed.

Lever A

Lever B

Step 1:
Push the lever closest to the "unlock" marking "

"

(below referred as lever A) down and away from
the socket to release it.

Step 3:
Gently press lever A to allow the load plate
to rise. Open the load plate. (Note: DO NOT
touch the socket contacts after the load plate is
opened.)

Step 5:
Once the CPU is properly inserted, carefully replace
the load plate. Then secure lever B under its reten­tion tab. The protective plastic cover may pop off
from the load plate during the process of engaging
the lever. Remove the cover. Save the cover properly
and always replace it when the CPU is not installed.

Step 2:
Push the lever closest to the "lock" marking "

(below referred as lever B) down and away from
the socket. Then lift the lever.

Step 4:
Hold the CPU with your thumb and index fingers.
Align the CPU pin one marking (triangle) with the
pin one corner of the CPU socket (or align the CPU
notches with the socket alignment keys) and care­fully insert the CPU into the socket vertically.

Step 6:
Finally, secure lever A under its retention tab to
complete the installation of the CPU.

- 13 -

"

Hardware Installation

1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

• Make sure that the motherboard supports the memory. It is recommended that memory of the
same capacity, brand, speed, and chips be used.

(

Go to GIGABYTE's website for the latest supported memory speeds and memory modules.

• Always turn off the computer and unplug the power cord from the power outlet before installing
the memory to prevent hardware damage.

• Memory modules have a foolproof design. A memory module can be installed in only one direc­tion. If you are unable to insert the memory, switch the direction.

1-4-1 FourChannelMemoryConguration

This motherboard provides four DDR3 memory sockets and supports Four Channel Technology. After the
memory is installed, the BIOS will automatically detect the specications and capacity of the memory. En­abling Four Channel memory mode will double the original memory bandwidth.
The eight DDR3 memory sockets are divided into four channels and each channel has two memory sockets
as following:
Channel A: DDR3_P0_A0, DDR3_P0_A1
Channel B: DDR3_P0_B0, DDR3_P0_B1
Channel C: DDR3_P0_C0, DDR3_P0_C1
Channel D: DDR3_P0_D0, DDR3_P0_D1

DDR3_P0_A0

DDR3_P0_A1

DDR3_P0_B0

DDR3_P0_B1

DDR3_P0_D1

DDR3_P0_D0

DDR3_P0_C1

DDR3_P0_C0

)

Due to CPU limitations, read the following guidelines before installing the memory in Four Channel mode.

1. Four Channel mode cannot be enabled if only one DDR3 memory module is installed.

2. When enabling Four Channel mode with two or four memory modules, it is recommended that
memory of the same capacity, brand, speed, and chips be used for optimum performance.

- 14 -

Hardware Installation

1-4-2 Installing a Memory

Before installing a memory module, make sure to turn off the computer and unplug the power
cord from the power outlet to prevent damage to the memory module.
Be sure to install DDR3 DIMMs on this motherboard.

Installation Step:

Step 1. Insert the DIMM memory module vertically into the DIMM slot, and push it down.
Step 2. Close the plastic clip at both edges of the DIMM slots to lock the DIMM module.
Note: For dual-channel and four-channel operation, DIMMs must be installed in matched pairs.
Step 3. Reverse the installation steps when you wish to remove the DIMM module.

2

1-4-3 DIMM Population Table

1N or 2N

R-DIMM

1N

1N

1N

1N

1N

1N

1N

1N

1N

DIMM1 DIMM0

Empty

Empty

Empty

Single-Rank

Single-Rank

Dual-Rank

Single-Rank

Dual-Rank

Quad-Rank

Single-Rank

Dual-Rank

Quad-Rank

Single-Rank

Dual-Rank

Dual-Rank

Quad-Rank

Quad-Rank

Quad-Rank

1

2

1N

1N

2N

Single-Rank

2N

2N

DIMM1 DIMM0

Empty

Single-Rank

Empty

Dual-Rank

Single-Rank Single-Rank

Dual-Rank

Dual-Rank

Dual-Rank

1N or 2N

U-DIMM

- 15 -

Hardware Installation

1-5 Back Panel Connectors

GA-6PXSV2

GA-6PXSV3

Serial Port

Connects to serial-based mouse or data processing devices.

Video Port

The video in port allows connect to video in, which can also apply to video loop thru function.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.

KVM Server Management 10/100 LAN Port

The LAN port provides Internet connection with data transfer speeds of 10/100Mbps.

USB 3.0 Port

The USB port supports the USB 3.0 specication. Use this port for USB devices such as a USB key­board/mouse, USB printer, USB ash drive and etc.

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices such as a USB key­board/mouse, USB printer, USB ash drive and etc.

Line In (Blue)

The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out (Front Speaker Out/Green)

The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surroundspeakers
can be connected to Line Out (Front Speaker Out) jack.

MIC In (Pink)

The default MIC In jack. Microphone must be connected to MIC In jack.

Surround Speaker Out (Rear Speaker Out/Black)

The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can beconnected

to Surround Speaker Out (Rear Speaker Out) jack.

- 16 -

Hardware Installation

Center/Subwoofer Speaker Out (Orange)

The default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connectedto Cen-

ter/Subwoofer Speaker Out jack.

Side Speaker Out (Grey)

The default Side Speaker Out jack. Surround side speakers can be connected to Side SpeakerOut jack.

Speed LED

10/100 LAN Port

Speed LED

10/100/1000 LAN Port

Link

Activity LED

Link

Activity LED

MLAN Speed LED:

State Description

Green On 10 0 Mbps data rate

Green Blink 10 Mbp s or 100 Mbp s

data rate

Off 10 Mbps dat a rate

82574 Speed LED:

State Description

Yel low O n 1 Gbps da ta rate

Yellow Blink Identify 1 Gbps data

rate

Green On 10 0 Mbps data rate

Green Blink Ide ntify 10 0 Mbps data

rate

Off 10 Mbps dat a rate

Link/Activity LED:

State Description

On Li nk b e twe en s y st em a n d ne t wo r k or n o

access

Blinking Data transmission or receiving is occurring

Off No data tran smission or rec eiving is occ urring

Link/Activity LED:

State Description

On Li nk b e twe en s y st em a n d ne t wo r k or n o

access

Blinking Data transmission or receiving is occurring

Off No data tran smission or rec eiving is occ urring

• When removing the cable connected to a back panel connector, rst remove the cable from your

device and then remove it from the motherboard.

• When removing the cable, pull it straight out from the connector. Do not rock it side to side to

prevent an electrical short inside the cable connector.

- 17 -

Hardware Installation

1-6 Internal Connectors

1819 25

16

15

3

4

14

24

13

23

12

26

11

21

6

22

10

1) P1

2) P2_CPU

3) CPU_FAN1 (CPU Fan)

4) SYS_FAN1 (System Fan)

5) SYS_FAN2 (System Fan)

6) SYS_FAN3 (System Fan)

7) PWR_DET1

8) SATA23/SATA45

9) SATA01

10) F_PANEL1

11) SAS0_3

12) F_USB3_2

13) F_USB3_1

20

2

17

7

5

9

8

1

14) TPM

15) F_USB1 (GA-6PXSV2 Only)

16) COM2

17) SATA_SGPIO

18) SPDIF_IN

19) BMC_LED1

20) BAT1

21) CLR_CMOS1

22) PASSWORD1

23) BIOS_RCVR

24) BIOS_WP

25) SSB_ME1

26) BMC_FRB1

Read the following guidelines before connecting external devices:

• First make sure your devices are compliant with the connectors you wish to connect.

• Before installing the devices, be sure to turn off the devices and your computer. Unplug the

• After installing the device and before turning on the computer, make sure the device cable has

power cord from the power outlet to prevent damage to the devices.

been securely attached to the connector on the motherboard.

- 18 -

Hardware Installation

1/2) P1/P2_CPU (2x12 Main Power Connector and 2x4 12V Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the com-

ponents on the motherboard. Before connecting the power connector, rst make sure the power supply

is turned off and all devices are properly installed. The power connector possesses a foolproof design.
Connect the power supply cable to the power connector in the correct orientation. The 12V power con­nector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will
not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high
power consumption be used (500W or greater). If a power supply is used that does not provide
the required power, the result can lead to an unstable or unbootable system.

P2_CPU

58

14

P2_CPU:

Pin No. Denition

1 GND

2 GND

3 GND

4 GND

5 +12V

6 +12V

7 +12V

8 +12V

P1

24

12

1

P1:

Pin No. Denition

1 3.3V

2 3.3V

3 GND

4 +5V

5 GND

6 +5V

7 GND

8 Power Good

9 5VSB (stand by +5V)

10 +12V

13

11 +12V

12 3.3V

Pin No. Denition

13 3.3V

14 -12V

15 GND

16 PS_ON

17 GND

18 GND

19 GND

20 -5V

21 +5V

22 +5V

23 +5V

24 GND

- 19 -

Hardware Installation

3/4/5/6) CPU_FAN1/SYS_FAN1/SYS_FAN2/SYS_FAN3 (CPU Fan/System Fan Headers)

DEBUG
PORT

DEBUG
PORT

The motherboard has a 4-pin CPU fan header (CPU_FAN1), three 4-pin (SYS_FAN1/SYS_FAN2/SYS_

FAN3) system fan headers. Most fan headers possess a foolproof insertion design. When connecting a
fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire).
The motherboard supports CPU fan speed control, which requires the use of a CPU fan with fan speed
control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the
chassis.

1

SYS_FAN1

Pin No. Denition

1 GND

2 +12V

3 Sense

4 Speed Control

SYS_FAN1

CPU_FAN1

1

CPU_FAN1

SYS_FAN2
SYS_FAN3

SYS_FAN2

SYS_FAN3

• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheat­ing. Overheating may result in damage to the CPU or the system may hang.

• These fan headers are not conguration jumper blocks. Do not place a jumper cap on the headers.

7) PWR_DET1 (Power management connector)

Pin No. Denition

1

5

1 SMB CLK

2 SMB DATA

3 SMB Alert

4 GND

5 3.3V Sense

- 20 -

Hardware Installation

8) SATA2345 (SATA 3Gb/s Connectors)

DEBUG
PORT

G.QBOFM

DEBUG
PORT

G.QBOFM

DEBUG
PORT

G.QBOFM

DEBUG
PORT

G.QBOFM

DEBUG
PORT

G.QBOFM

DEBUG
PORT

G.QBOFM

The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.

Each SATA connector supports a single SATA device.

7

7

SATA45

1

7

1

7

1

1

SATA23

Pin No. Denition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

• A RAID 0 or RAID 1 conguration requires at least two hard drives. If more than two hard
drives are congured, the total number of hard drives must be an even number.

• A RAID 10 conguration requires four hard drives.

(Note) When a RAID conguration is built across the SATA 6Gb/s channels, the system performance of
the RAID conguration may vary depends on the devices are connected.

9) SATA01 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and

1.5Gb/s standard. Each SATA connector supports a single SATA device.

Pin No. Denition

1 GND

1

1

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

7

7

SATA01

- 21 -