How it Works
GE
Loading...
PT7550S

GE JT3000DF1CC, JT5000SF1SS, JT5000DF1WW, JT5000DF1BB, JT3000DF1WW Installation Instructions Manual

...
Installation Instructions
27" & 30" Electric Built-in Wall Ovens
Questions? Calt 1.800.GE.CARES(1.800.432.2737) or visit www.GEAppiiances.com
In Canada, calt 1.800.561.3344 or visit www.GEAppliances.ca
BEFORE YOU BEGIN
Reed these instructions completelg end cerefullg.
" IM PORTANT -- Save these instructions
" IMPORTANT -- Observe allgoverning
codes and ordinances.
, Note to Installer- Be sure to leave these
instructions with Consumer.
, Note to Consumer- Keep these instructions
for future reference.
, Skill level- Installation of this appliance
requires a qualified installer or electrician.
. Proper installation is the responsibility
of the installer.
, Product failure due to improper installation
isnot covered under Warranty.
, Product is for indoor use onlg.
ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired)into an
approved junction box. A plug and receptacle is NOT permitted on these products.
FOR YOUR SAFETY:
WAR NING:Beforebeginning the installation, switch power off at the service panel and
lock the service disconnecting means to prevent power from being switched on accidentallg. When the service disconnecting means cannot be locked, securelg fasten a prominent warning device, such asa tag,
to the service panel. Besure the oven is securelg installed ina cabinet that is firmlg attached to the house structure.
Weight on the oven door could cause the oven to tip and result in injurg. Never allow angone to climb, sit, stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to 200°F [93.3°C])generated bg the oven.
MATERIALS YOU MAY NEED
JunctionBox
Wire Nuts Strain Relief Clamp for 1/2" Conduit
TOOLS YOU MAY NEED
1/8" Drill Bit and Electric or Hand Drill PhillipsScrewdriver
Wire Strippers
DESIGN INFORMATION
SINGLEOVEN INSTALLATIONS The singleoven mag be installed in a cabinet alone or above a warming drawer. Thesingle oven meg also
be installed below a countertop or below specified cooktops. Seethe label ontop of the oven for approved models.
DOUBLEOVENINSTALLATIONS Adouble oven mag beinstalled in a cabinet alone or above a warming drawer. Seethe label on top of the
oven for approved models.
IMPORTANT:Alwagsreferto individualinstallationinstructionspackedwith eachproductforspecific requirements.
I_] PREPARE THE OPENING
NOTE: If the cabinet does not have a solid bottom, two braces or runners must be installed to support the weight of the oven. For single ovens, the runners and braces must support 200 Ibs 191kg). For double ovens, the runners and braces must support 375 Ibs. 1170 kg).
NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it mag be necessarg to add wood shims under the runners and front trim until the marks or opening are covered.
NOTE: If the cabinet does not have a front frame and the sides are less than sA"11.9cm) thick, shim both sides equallg to establish the cutout width.
2" x 4"(5 cm x 10 cm)
or Equivalent Runners Level
with Bottom of Cutout
and Flush with Sides of Cutout
Suitable Bracing
to Support.
m
Ill REMOVE PACKAGING MATERIALS
Failure to remove packaging materials could result in damage to the appliance. Remove all packing parts from oven, racks and heating elements. Remove protective film and labels on the outer door and control panel. Also, remove plastic on trims and panel, all tape around the oven and ang shipping
screws securing the oven to the base pad. Open oven door and remove literature pack and oven
racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separatelg and taped to the top of the unit. Remove pedestal rails from
separate box and set aside (30" Double Wall Ovens Onlg).
r_==_ CUTOUT FOR SINGLE OVENS IN WALL CABINET
NOTE: If the cabinet does not have a front frame and the sides are less than sA" (1.9 cm) thick, shim both sides equally to establish the cutout width.
These ovens
are not approved for
stackable installations.
Opening Between Inside Wails Must be at Least 28-1/2" (724 cm) Wide
H
Sideby-SideInstallations
Installtwo ovensin separatecutouts
CenterLine CenterLine
] so.s"177scrnl ] I 30"models I
] 2T' (68.58crn) ] I 27"modes !
I !
--I
Cutout- Cutout -
observeall observeall dimensionsand dimensionsand requirements requirements
"---_1 I_== 2"Is1cm/r_in
Junction Box Location (junction box may
Jbe located
in adjacent cabinetl
: --T
22" (559 __-=_lm
cm} Hin. to
_ Bottomof
J Junction J BOX
J
..... ~%:;, ....
-" " Cutou/Depth
(59.7cm} Nlin.
Note: Allow
1/4" (0.64 cm) clearances from side edges of oven door.
_____B___-_
t
F
G
............................... L ......
t
C
m
4_
Recommended
Cutout Location
from Floor
32 1/2" (826cm)
A---d
Dimension Dimension Description 27" Single Oven 30" Single Oven
A Cabinet Width 27" (68.6 cm) 30" (76.2 cm) B Cutout Width 25" (63.5 cm) min. 28½" (72.4 cm) min.
25½" (64.1 cm) max. 28sA " (72.7 cm) max.
C Cutout Height 27%" (70.2 cm) min. 27½" (69.2 cm) min.
28½" (71.4 cm) max. 27s4d ' (69.4 cm) max.
D Overlap of Oven Over 1" (2.5 cm) _¼_d'(1.75 cm)
Side Edges of Cutout
E Clearance to 23" 150.8 cm) min. 23" 153.3 cm) min.
Adjacent Corners,
Drawers, Walls, etc.,
When Door Is Open
F Overlap of Oven 1" 12.5 cm) min. 1" 12.5 cm) min.
Top of Cutout (11/4'' 13.2 cm) for PT9050)
G Overlap of Oven 1" (2.5 cm) min. 1½" (3.2 cm)
Bottom of Cutout
H Junction Box Location 8¾" (22.2 cm) max. 9½" (24.1 cm) max.
right side only right side only
CUTOUT FOR SINGLE OVENS - UNDER COUNTER
NOTE: These ovens are only approved to be installed under the specific models as labeled on the unit.
Gas or Electric Cooktops May Be Installed Over This Oven. See Cooktop Installation instructions for Cutout Size, 240V/208V
See Label on Top of Oven for Approved Models. Junction Box
Location (junction
box may be
in adjacent cabinet)
25" (63.5 cm)
Gas and Electrical Connections for Gas Cooktop Must be Located in an Adjacent Accessible Location to the Right
MUST SUPPORT 200 Ibs. (60 kg) FOR SINGLE OVENS MUST SUPPORT 375 Ibs. (170 kg) FOR DOUBLE OVENS
Side-by-Side Installations
Install two ovens in separate cutouts.
center Line CenterLine
I 30.5" (775cm) 30" models
36" (91.4 cm) Countertop
Height
Cutout - observe all dimensions and
requirements.
__q
JL
Cutout = observe
all dimensions and
requirements.
_=2" (5.l cm)Nlin.
NOTE:One cooktop may be centered over either oven in
the side-by-side installation.
Dimension Dimension Description 27" Single Oven 30" Single Oven
A Cabinet Width 25" (63.5 cm) min. 28½" (72.4 cm) min.
25¼" (64.1 cm) max. 28%" (72.7 cm) max.
B Cutout Height 27%" (70.2 cm) min. 27½" (69.2 cm) min.
28½" (71.4 cm) max. 27%d' (69.4 cm) max.
C Unit Overlap Top 1" (2.5 cm) 1" (2.5 cm)
(1VJ' (5.2 cm) for PT9050)
D Unit Overlap Bottom 1" (2.5 cm) l_/J ' (5.2 cm)
E Unit Overlap Side Edges 1" (2.5 cm) _¼_d'(1.75 cm) F Junction Box Location 8sA" (22.2 cm) max. 9½" (24.1 cm) max.
right side only right side only
Continue to Section 4.
CUTOUT FOR DOUBLE OVENS (2THERMAL OVENS)
NOTE: If the cabinet does not have a front frame and the sides are less than sA"(1.9 cm)
both sides equall_h.i
Junction
BO×
Location
(junction
/ boxmay
/be located
in adjacent
cabinet)
l
J
O _
t
F
G
t
hick, shim
i
r
%
r
i
Dim. Description 27" Double Oven 30" Double Oven with 30" Double Oven
Pedestal without Pedestal
A Cabinet Width 27" (68.6 am) 30" (76.2 am) 30" (76.2 am)
B Cutout Width 25" (63.5 cm) min. 28½" (72.4 cm) min. 28½" (72.4 cm) min.
25¼" (64.1cm) max. 28%" (72.7 cm) max. 28%" (72.7 cm) max.
C Cutout Height 4%_d' (126.2cm) min. 5113/S' (131.6 cm) min. 50 ¼" (127.64cm)
50½" (127.5 am) max. 51_/_d' (151.9 am) max.
D Overlap of Oven 1" (2.5 am) _½d' (1.75 am) _4d' (1.75 am)
Over Side Edges
of Cutout
E Clearanceto 23" (50.8 cm) min. 23" (53.3 cm) min. 23" (53.3 cm) min.
Adjacent Corners,
Drawers, Walls, etc., When Door/sOpen _ ,
F Overlap of Oven 1" (2.5 am) rain. 1" (2.5 cm) min. 1" (2.5 cm) min.
Top of Cutout (1¼"(5.2cm) for PT9550) (1¼"(5.2 cm) for PT9550)
G Overlap of Oven 1" (2.5 cm) min. 11/4"(5.2 cm) 11/4"(5.2 cm)
Bottom of Cutout
H Junction Box 8sA" (22.2 cm) max. 9½" (24.1 cm) max. 9½" (24.1 cm) max.
Locat!on _ rights!de only _ rights!de only . rights!de only
J Height to Bottom 44" (111.8cm) 47" (i19.4cm) 47" (i19.4cm)
of Junction Box
K Recommended 15¼" (55.7 am) 12" (50.5 am) 12" (50.5 am)
Cutout Location
from Floor
Continue to Section 3.
J31-i0856-iJo -isGE
CUTOUT FOR INSTALLATION OVER A WARMING DRAWER
NOTE: Installtheoven onlywithspecificmodels listedon the labellocatedon topoftheoven. NOTE: Additionalclearancesbetween cutoutsmay be required.Checktobe suretheoven supports
above theWorming Drawer locationdo notobstructtherequiredinteriordepthand height. When installinga Worming Drawer below a singleordoubleoven,a separate120V,60 HZ,properly
grounded receptaclemustbe installed.Referto installationinstructionspocked with theWorming Drawer forspecificinstallationrequirements.
Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement
2" (5.1 cm)
Min.
Per Warming Drawer
Requirement
Continue to Section 3 for DWO with Pedestal. Otherwise, continue to Section 4.
_-I PEDESTAL RAIL INSTALLATION (DOUBLE OVENS ONLY)
A. Place one pedestal rail on each cabinet runner or centered on opposite side of solid cabinet bottom
flush with side of cabinet opening. Locate each rail so that front of rail is behind front cabinet
opening.
B. Drill pilot holes and attach rails to runner or bottom of cabinet with provided hardware.
[_ DOOR REMOVAL {RECOMMENDED)
NOTE: Door removal is not a requirement for installation of the product but is an added convenience.
To remove the door:
A. Open the oven door as far as it will go.
B. Push both hinge locks down toward the door frame
to the unlocked position. This may require a flat-
blade screwdriver. DO NOT LIFTTHE DOOR BYTHE HANDLE!
C. Place hands on both sides of the door and close the
oven door to the removal position (approximately 1"-2" [2.5 cm-5.1 cm] from the closed position).
D. Lift the door up and out until the hinge arms clear
the slots. NOTE: The oven door is very heavy. Be sure you have a firm grip before lifting the oven door off the hinges. Use caution once the door is removed. Do not lay the door on its handle.
This could cause dents or scratches.
Hinge
_1_ Unlocked
Position
Hinge Slot ,
Hinge Arm
Hinge Clears Slot
r_ ELECTRICAL REQUIREMENTS
A WARNING: This appliance rnust be properly grounded
A WAR N I N G: To prevent fire or shock, do not use an extension cord with this appliance.
A WA R N I N G: To prevent shock, remove house fuse or open circuit breaker before
beginning installation.
A WAR N IN G: ,mproperconnectionofa,uminumhousewiring to copper leads can result
in an electrical hazard or fire. Useonly connectors designed for joining copper to aluminum and follow the manufacturer's recommended procedure closely.
We recommend you have the electrical wiring and hookup of your appliance connected by a qualified electrician. After installation, have the electrician show you how to disconnect power from the appliance.
You must use a single-phase, 120/208 VACor 120/240 VAC,60 Hertzelectrical system. If you connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring must be used.
Effective Januarg 1, 1996,the National Electrical Code requires that new construction (not existing) utilize a four-conductor connection to an electric oven. When installing an electric oven in new construction, a mobile home, recreational vehicle or an area where local codes prohibit grounding through the neutral conductor, refer to the section on four-conductor branch circuit connections.
Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven according to governing codes could result in a hazardous condition. If there are no local codes, your oven must be wired and fused to meet the National Electrical Code, NFPA No. 70 i latest edition, available from the National Fire Protection Association.
[_] ELECTRICAL REQUIREMENTS {CONT.)
Thisappliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse. See the rating plate located on the oven frame to determine the rating of the product•
Rating Plata
Location ....................................;
_================_ _
Rating plate is located on the oven side trim.
Use the chart below to determine the minimum recommended dedicated circuit protection:
Recommended
KW Rating KW Rating Circuit Size
240V 208V {Dedicated)
<4.8 KW <4.2 KW 20 Amp
4.9 KW=7.2 KW 4.2 KW=6.2 KW 30 Amp
7.3 KW-9.6 KW 6.3 KW-8.3 KW 40 Amp
9.7 KW-12.0 KW 8.4 KW-10.4 KW 50 Amp
DO NOTshorten the flexible conduit. The conduit strain relief clamp must be securely attached to the
junction box and the flexible conduit must be securely attached to the clamp. If the flexible conduit will not
fit within the clamp, do not install the oven until a clamp of the proper size isobtained• The 3 power leads supplied with this appliance are suitable for connection to heavier gauge household
wiring. The insulation of these 3 leads israted for temperatures much higher than the temperature rating of the household wiring. Thecurrent-carrying capacity of the conductor is governed by the wire gauge and the temperature rating of the insulation around the wire.
Loading...
+ 11 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use