GE Logix 740C-ET, Logix 760C-ET Quick Start Manual
Autotrol
Series 255 Valve
Series 263 Valve
Series 268 Valve
740C-ET & 760C-ET
Controllers
Quick Start Manual
LOGIX™ SERIES INSTALLER QUICK-START SHEET
LOGIX SERIES CONTROLLERS
740 Controller - Electronic time clock control capable of doing 7-day (day of
week) regeneration, or up to a 99 interval day regeneration. This control will
operate both in a conditioner (softener) or 3-cycle filter mode with the same
controller.
760 Controller - Electronic metered-demand (volumetric) controller which
regenerates based on the water usag e of the installation site. A calendar
override is a standard feature on this controller.
The Logix Series will operate on both the 255 and Performa valve body series.
LCD Display
SU MO TU WE TH FR SA DAYS
Time & Day
Regen Time & Day
Salt
x2
Capacity
P
Hardness
H
C
DOWN Button
SET Button
INITIAL POWER-UP
Initial Power Up - (CAMSHAFT proceeds to HOME position)
• At initial power-up, the camshaft will need to rotate to the HOME
(in service) position.
• Camshaft may take 1-2 minutes to return to home position.
• Err 3 will be displayed until the camshaft returns to home.
• If more than 2 minutes elapses, verify that the motor is turning the
camshaft. If it is not turning, see the troubleshooting section in Dealer
Installation and Service Manual.
Time & Day
Regen Time & Day
Capacity
Hardness
SU MO TU WE TH FR SA DAYS
Salt
INITIAL START-UP STEP-BY-STEP INSTRUCTIONS
PM
MIN
LBS
KG
x100
UP Button
Manual Regeneration
Time & Day
Regen Time & Day
Salt
Capacity
Hardness
Time & Day
Regen Time & Day
Capacity
Hardness
SU MO TU WE TH FR SA DAYS
SU MO TU WE TH FR SA DAYS
Salt
Step 1: Program System Size
This step may have been performed by your system’s OEM manufacturer. In
this case, proceed to step 2
• Input tank diameter size in inch (7-8-9-10-11-12-13-14-16).
• Use UP and DOWN buttons to scroll diameter choices.
• "11" value corresponds to 10x44 and 10x54 tank sizes.
• To choose a 3-cycle filter operation - press DOWN until an "F" is displayed.
• Press SET to accept the system size you’ve selected.
• If incorrect setting is programmed, see "Resetting the Control" section
below.
.
1
SU MO TU WE TH FR SA DAYS
Time & Day
Capacity
Hardness
Step 2: Program Time of Day
• While "12:00" is blinking, set the correct time of day.
• Use the UP and DOWN buttons to scroll to the correct time of day.
• "PM" is indicated, "AM" is not indicated.
• Press SET to accept the correct time of day and advance to the next parameter.
Step 3: Set Day of Week
Time & Day
Regen Time & Day
Capacity
Hardness
Time & Day
Regen Time & Day
Salt
Capacity
Hardness
Time & Day
Regen Time & Day
Salt
Capacity
Hardness
SU MO TU WE THFRSA DAYS
Salt
SU MO TU WE TH FR SA DAYS
SU MO TU WE TH FR SA DAYS
• Press SET to make the arrow under SU flash.
• Use the UP and DOWN butt ons to advance th e arrow until it is under the co rrect da y of
week.
• Press SET to accept and advance to the next parameter.
After steps 1-3, the controll er will operate most syste ms. Proce ed to step 4 if further
adjustments to your system’s programming is needed.
To exit the programming state, wait 30 seconds and the controller will automatically put
you into the normal operating mode.
Step 4: Set Regen Time
• 2:00 (AM) is the default time of regeneration. To accept this time, press the DOWN
button to move to step 5.
• To change the regen time, press SET - causing 2: 00 to flash.
• Use the UP and DOWN buttons to advance to the desired regen time.
• Press SET to accept the time and advance to the next parameter.
Step 5: Set Days to Regenerate (740 Time-clock Control Only)
• If using 760 control - proceed to step 5b
• Set number of da ys between time-clock regeneration (regen fr equency).
• Default time is 3 days.
• Days can be adjusted from 1/2 (.5) to 99 days.
• To change, press SET to make the "3" flash.
• Use the UP and DOWN but tons to change to the number of days desired.
• Press SET to accept the regen frequency, and advance to the next cycle.
To use the 7-day timer option - see full Dealer Installation Manual.
Time & Day
Regen Time & Day
Salt
Capacity
Hardness
2
SU MO TU WE TH FR SA DAYS
Step 5a: Regeneration in a specific day of week (7 days timer)
• To set the regeneration in specific days, set "0" in calendar override.
• Done this, the arrow in the left side of the display indicates hour/ regeneration day.
• Press SET button and a flashing cursor will be displayed at the top under Sunday.
• The day of the week can be adjusted when the cursor at desired position.
• To select or delete the day of week, the triangular cursor has to be under this day.
• If the cursor is in position but fixed, press SET button to make it flashing.
• To move the cursor when is fixed use UP and DOWN buttons, press SET if is flashing.
Loading...