GE DPSB613, DPSB619 User Manual

Safety Instructions . . . . . . . . 2–5

Operating Instructions

Automatic Settings . . . . . . . . . 7, 8
Control Panels . . . . . . . . . . . . . . 6
Control Features . . . . . . . . . . . .10
Cycle Options . . . . . . . . . . . . . .11
Cycle Status . . . . . . . . . . . . . . . .12
Dryer Features . . . . . . . . . . . . . .13
Drying Cycles . . . . . . . . . . . . . . . .8
Dryness Levels . . . . . . . . . . . . . . .9
Loading and Using the Dryer . . .15 O
NE TOUCH Cycles . . . . . . . . . . . .6
O
NE TOUCH Selections . . . . . . . . .7
Reversing the Door . . . . . . . . . .14
Special Dry Cycles . . . . . . . . . . . .8
Timed Dry Cycles . . . . . . . . . . . .9
Venting the Dryer . . . . . . . . . . .16
Troubleshooting Tips . . . . .17–19

Consumer Support

Consumer Support . . . Back Cover
Warranty . . . . . . . . . . . . . . . . . . 23
GEAppliances.com
Dryers
500A277P047 175D1807P424 49-90160 06-03 JR
DPSB613 DPSB619
Owner’s Manual
Profile
Write the model and serial numbers here:
Model # ________________
Serial # ________________
They are on the label on the front of the dryer behind the door.
2

Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.
California Safe Drinking Water and Toxic Enforcement Act
This act requires the governor of California to publish a list of substances known to the state to cause cancer, birth defects or other reproductive harm and requires businesses to warn customers of potential exposure to such substances.
Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.
Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or death.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light a match, or cigarette, or
turn on any gas or electrical appliance.
Do not touch any electrical switch; do not
use any phone in your building.
Clear the room, building or area of all
occupants.
Immediately call your gas supplier
from a neighbor’s phone. Follow the gas supplier’s instructions carefully.
If you cannot reach your gas supplier,
call the fire department.
5
4
3
2
1
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of this or any other appliance.
Installation and service must be performed
by a qualified installer, service agency or the gas supplier.
Properly ground dryer to conform with all governing codes and ordinances. Follow details in Installation Instructions.
Install or store where it will not be exposed to
temperatures below freezing or exposed to the weather.
Connect to a properly rated, protected and sized
power supply circuit to avoid electrical overload.
Remove the colored protective film from the
control panel.
Remove all sharp packing items and dispose of
all shipping materials properly.
Exhaust/Ducting:
Gas dryers MUST be exhausted to the outside.
Use only rigid metal 4diameter ductwork inside the dryer cabinet. Use only rigid metal or flexible metal 4diameter ductwork for exhausting to the outside. USE OF PLASTIC OR
OTHER COMBUSTIBLE DUCTWORK CAN CAUSE A FIRE. PUNCTURED DUCTWORK CAN CAUSE A FIRE IF IT COLLAPSES OR BECOMES OTHERWISE RESTRICTED IN USE OR DURING INSTALLATION.
For complete details, follow the Installation Instructions.
2
1
3
PROPER INSTALLATION
This dryer must be properly installed and located in accordance with the Installation Instructions before it is used. If you did not receive an Installation Instructions sheet, you can receive one by visiting GEAppliances.com, or by calling 800.GE.CARES (800.432.2737).
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
GEAppliances.com
4
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
YOUR LAUNDRY AREA
Keep the area underneath and around your appliances free of combustible materials (lint, paper, rags, etc.), gasoline, chemicals, and other flammable vapors and liquids.
Keep the floor around your appliances clean and dry to reduce the possibility of slipping.
Close supervision is necessary if this appliance is used by or near children. Do not allow children to
play on, with, or inside this or any other
appliance.
Keep all laundry aids (such as detergents, bleaches, etc.) out of the reach of children, preferably in a locked cabinet. Observe all warnings on container labels to avoid injury.
Never climb on or stand on the dryer top.
WHEN USING YOUR DRYER
Never reach into the dryer while the drum is moving. Before loading, unloading or adding clothes, wait until the drum has completely stopped.
Clean the lint filter before each load to prevent lint accumulation inside the dryer or in the room. DO NOT OPERATE THE DRYER WITHOUT
THE LINT FILTER IN PLACE.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.) which may ignite or explode. Do not add these substances to the wash water. Do not use or place these substances around your washer or dryer during operation.
Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a clothes load to catch fire
.
Any article on which you have used a cleaning solvent or that contains flammable materials (such as cleaning cloths, mops, towels used in beauty salons, restaurants or barber shops, etc.) must not be placed in or near the dryer until solvents or flammable materials have been removed. There are many highly flammable items used in homes such as acetone, denatured alcohol, gasoline, kerosene, some household cleaners, some spot removers, turpentines, waxes, wax removers and products containing petroleum distillates.
The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer’s care instructions.
Do not dry articles containing rubber, plastic, foam or similar materials such as padded bras, tennis shoes, galoshes, bath mats, rugs, bibs, baby pants, plastic bags, pillows, etc., that may melt or burn. Some rubber materials, when heated, can under certain circumstances produce fire by spontaneous combustion.
Do not store plastic, paper or clothing that may burn or melt on top of the dryer during operation.
Garments labeled Dry Away from Heat or Do Not Tumble Dry (such as life jackets containing kapok)
must not be put in your dryer.
Do not dry fiberglass articles in your dryer. Skin irritation could result from the remaining particles that may be picked up by clothing during subsequent dryer uses.
To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the dryer at the building’s distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning (except the removal and cleaning of the lint filter). NOTE: Pressing STOP does NOT disconnect the appliance from the power supply.
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
WHEN NOT USING YOUR DRYER
Grasp the plug firmly when disconnecting this appliance to avoid damage to the cord while pulling. Place the cord away from traffic areas so it will not be stepped on, tripped over or subjected to damage.
Do not attempt to repair or replace any part of this appliance or attempt any servicing unless specifically recommended in this Owner’s Manual or in published user-repair instructions that you understand and have the skills to carry out.
Before discarding a dryer, or removing it from service, remove the dryer door to prevent children from hiding inside.
Do not tamper with controls.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
5
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
GEAppliances.com
WHEN USING YOUR DRYER (cont.)
Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.
The interior of the machine and the exhaust duct connection inside the dryer should be cleaned at least once a year by a qualified technician. See the Loading and Using the Dryer section.
If yours is a gas dryer, it is equipped with an automatic electric ignition and does not have a pilot light. DO NOT ATTEMPT TO LIGHT WITH A MATCH. Burns may result from having your hand in the vicinity of the burner when the automatic ignition turns on.
You may wish to soften your laundered fabrics or reduce the static electricity in them by using a dryer-applied fabric softener or an anti-static conditioner. We recommend you use either a fabric softener in the wash cycle, according to the manufacturer’s instructions for those products, or try a dryer-added product for which the manufacturer gives written assurance on the package that their product can be safely used in your dryer. Service or performance problems caused by use of these products are the responsibility of the manufacturers of those products and are not covered under the warranty to this appliance.
Model DPSB613
Model DPSB619
ONE TOUCH
Quick Start Guide
• Clean lint filter
• Add clothes
• Select dry cycle
• Check dryness level
• Check heat setting
• Close door
• Push START
Your new dryer offers the convenience of starting your dryer loads with our easy ONE TOUCH cycles. Make one simple selection, and your DRYNESS LEVEL and HEAT SETTING are automatically set. Then all you have to do is press START.
Easy ONE TOUCH cycles.
You can locate your model number on the label on the front of the dryer, behind the door.
NOTE: Any time you make a selection that is incompatible with the chosen dry cycle, the dryer will beep twice.
Dryer control panel.
6
7
PRESS... AUTOMATICALLY SELECTS... THEN PRESS...
For cottons and most linens.
NOTE: During SPEED DRY
you will see:
ONE TOUCH cycles use the Sensor Dry Plus feature, which continuously monitors the amount of moisture in the load and stops the dryer when the clothes are dry. Throughout this manual, features and appearance may vary from your model.
ONE TOUCH selections. GEAppliances.com
For loads consisting of cottons and poly-blends.
For wrinkle-free and permanent press items.
For knits and sweaters with fabric care labels that say “Machine Dry”.
For lingerie and special-care fabrics.
(on some models) For small loads that are needed in a hurry,
such as sport or school uniforms. Can also be used if the previous cycle left some items damp, such as collars or waistbands.
You can change any of the automatic settings by simply pressing the desired pads.
Changing the automatic settings.
8
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
DRYEL
(on some models)
This feature is designed for use with the DRYEL™“dry-clean only” fabric care system. See product package for directions.
For questions or issues related to the use and performance of DRYEL™, call 1-800-214-8913, or visit the DRYEL™Website at www.dryel.com.
Automatic DRYEL™settings:
DEWRINKLE
Use this feature to remove wrinkles from items that are dry or slightly damp.
Automatic DEWRINKLE settings:
AIR DRY
Use this feature to tumble items without heat.
CUSTOM Cycle (on some models)
Set up your favorite combination of settings and save them here for one-touch recall.
These custom settings can be set while a cycle is in progress.
Some models have two CUSTOM pads to store two different custom combinations.
To store a custom combination of settings:
1. Select a ONE TOUCH setting.
2. Change DRYNESS LEVEL and HEAT SETTING to fit your needs.
3. Select any drying OPTIONS you want.
4. Press and hold the CUSTOM Cycle pad for three seconds to store your selection. A beep will sound and the pad will light up.
To recall your stored combination:
Press the CUSTOM Cycle pad, then press START.
To reprogram the CUSTOM settings:
Repeat steps 1-4 above.
Automatic AIR DRY settings:
Throughout this manual, features and appearance may vary from your model.
About drying cycles.
9
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
MORE DRY
Use for heavy-duty fabrics.
DRY
Use for a normal dryness level suitable for most loads. This is the preferred cycle for energy saving.
LESS DRY
Use for lighter fabrics.
DAMP
For leaving items partially damp.
OR
About dryness levels. GEAppliances.com
To use TIMED DRY:
1. Select the drying time.
2. Select the HEAT SETTING.
3. Select any OPTIONS. (NOTE: The ANTI-BACTERIAL option is not available with TIMED DRY cycles.)
4. Close door.
5. Push START.
About timed dry cycles.
HIGH
For regular to heavy cottons.
MEDIUM
For synthetics, blends and items labeled permanent press.
LOW
For delicates, synthetics and items labeled Tumble Dry Low.
EXTRA LOW
For lingerie and special-care fabrics.
About heat settings.
10
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
START/PAUSE
Press twice to select the last cycle you used and start the dryer.
If you have selected a new cycle, press once to start the cycle.
If the dryer is running, press once to interrupt the cycle; press again to continue
the cycle.
Throughout this manual, features and appearance may vary from your model.
About control features.
STOP
This pad should not be used to interrupt or pause a cycle.
Pressing this pad will cancel the current settings.
Estimated Time Remaining
Each time the dryer is used, it “learns” what types of loads you dry most often. It takes this data and determines the approximate time it will take the load to dry.
As the cycle begins, you will see the approximate total cycle time in the display. Then lights will flash in the display, and the SENSING light will flash. This means the dryer is continuously monitoring the amount of moisture in the load. The lights will continue until the dryer senses a low level of moisture in the load. At that point, the dryer will calculate and display the approximate time remaining.
11
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
About cycle options.
NOTE: Not all features are available on all dryer models. GEAppliances.com
(Appearance and
features may vary)
SIGNAL
Alerts you that the cycle is complete. The beeper will continue to sound every two minutes for the next 6 minutes, until the clothes are removed. The clothes should be removed when the beeper goes off so wrinkles won’t set in.
On some models, press SIGNAL to turn the beeper on or off.
On some models, press SIGNAL to select low or high volume, or to turn the beeper off.
EXTEND TUMBLE
Minimizes wrinkles by adding approximately 20 minutes of no-heat tumbling after clothes are dry. The beeper will sound every 90 seconds to remind you to remove the clothes. The EST. TIME REMAINING display will show 00.
ADD TIME (on some models)
This option can be used to extend drying time at the end of any cycle. Each time the pad is pressed, 10 minutes is added.
ANTI-BACTERIAL (on some models)
This option can only be used with the COTTONS or MIXED LOADS cycles. This option reduces certain types of bacteria by 99.9%, including: Staphylococcus aureus, Pseudomonas aeruginosa, and Klebsiella pneumoniae*. The anti-bacterial process occurs when high heat is used during a portion of the drying cycle.
NOTE: Do not use this cycle on delicate fabrics.
* The Anti-Bacterial Cycle is Certified by NSF International (formerly National Sanitation
Foundation) to NSF Protocol P154 Sanitization Performance of Residential Clothes Dryers.
NSF Protocol P154
Sanitization Performance of
Residential Clothes Dryers
DELAY 1–8 HOURS (on some models)
Use to delay the start of your dryer for 1 to 8 hours. First choose your dry cycle and any options. Then press this pad for the number of hours you want to delay the cycle.
Press the START pad to start the countdown.
The countdown time will be shown in the EST. TIME REMAINING display.
NOTE: If the door is opened while the dryer is in DELAY, the dryer will beep once a minute to remind you to restart the countdown. The countdown time will not restart unless the door is closed and START has been pressed again.
DAMP SIGNAL (on some models)
This option causes the dryer to beep when clothes have reached a damp dryness. Remove items that you wish to hang dry. The DAMP SIGNAL will only beep when the dryer SIGNAL is turned on.
WARM UP (on some models)
This option provides 10 minutes of warming time to warm up clothes. Perfect for use on a cold day, or to warm towels or robes.
E
N
D
T
I
I
S
E
R
A
L
12
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
These cycle status indicator lights display what part of the cycle the dryer is in and remind you to clean the lint filter.
About cycle status.
SensorDry Plus
This light comes on when a ONE TOUCH Sensor Dry Cycle is selected.
TIMED DRY
This light comes on when AIR DRY, DEWRINKLE, DRYEL™(on some models) or TIMED DRY is selected.
EXTENDED TUMBLE
This light comes on when the EXTEND TUMBLE option is selected.
CLEAN LINT FILTER
This light is a reminder to clean the lint filter. It comes on at the end of a cycle and goes off when the door is opened.
SENSING
Sensor Dry Cycles provide greater drying accuracy than standard machines, resulting in shorter dry times and better clothes care. The SENSING light will flash and lights will flash in the display while the dryer is monitoring the amount of moisture remaining in the clothes. When the SENSING light goes out, the dryer will calculate and display the approximate time remaining.
13
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Drum Lamp
Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect the dryer at the household distribution panel by removing the fuse or switching off the circuit breaker. Reach above dryer
opening from
inside the drum. Remove the
bulb and replace with the same size bulb.
About dryer features. GEAppliances.com
Drying Rack (on some models)
A handy drying rack may be used for drying delicate items such as washable sweaters.
Hook the rack over the lint filter so the rack extends into the dryer drum.
NOTE:
The drying rack must be used with the TIMED DRY cycles.
Do not use this drying rack when there are other clothes in the dryer.
14
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
15
Fabric Care Labels
Machine wash cycle
Normal
Permanent Press/
wrinkle resistant
Gentle/ delicate
Hand wash
Do not wash Do not wring
Water temperature
Hot
(50°C/120°F)
Warm
(40°C/105°F)
Cold/cool
(30°C/85°F)
Tumble dry
Dry
Normal
Permanent Press/
wrinkle resistant
Gentle/
delicate
Do not tumble dry
Do not dry (used with
do not wash)
Heat setting
High
Medium
Low
No heat/air
Special instructions
Line dry/
hang to dry
Drip dry
Dry flat
In the shade
Below are fabric care label “symbols” that affect the clothing you will be laundering.
WASH LABELS
DRY LABELS
Always follow the fabric manufacturer’s care label when laundering.
Loading and using the dryer. GEAppliances.com
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
Bleach symbols
Any bleach
(when needed)
Only non-chlorine bleach
(when needed)
Do not bleach
BLEACH LABELS
Sorting and Loading Hints
As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to sort items according to size. For example, do not dry a sheet with socks or other small items.
Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce®Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions.
Do not overload. This wastes energy and causes wrinkling. Do not dry the following items: fiberglass items, woolens,
rubber-coated items, plastics, items with plastic trim and foam-filled items.
Care and Cleaning of the Dryer
The Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your warranty.
The Lint Filter: Clean the lint filter before each use. Moisten your fingers and reach into the filter opening. Run your fingers across the filter. Have a qualified
technician vacuum the lint from the dryer once a year.
Stainless Steel: To clean stainless steel surfaces, use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel surfaces. Remove the cleaner residue, and then dry with a clean cloth.
The Exhaust Duct: Inspect and clean the exhaust ducting at least once a year to prevent clogging. A partially clogged exhaust can lengthen the drying time.
Follow these steps:
Turn off electrical supply by disconnecting the plug from the wall socket.
Disconnect the duct from the dryer.
Vacuum the duct with the hose attachment and reconnect the duct.
The Exhaust Hood: Check from the outside that the flaps of the hood move freely when operating. Make sure that there is no wildlife (birds, insects, etc.) nesting inside the duct or hood.
3
2
1
16
17

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Troubleshooting Tips Save time and money! Review the charts on the following pages, or visit GEAppliances.com. You may not need to call for service.
OPERATION Possible Causes What To Do
Control pads not Controls accidentally put in Press STOP. responding service mode
Dryer doesn’t start Control panel is “asleep” This is normal. Press START twice to choose the last cycle
you used and to start the dryer.
Dryer is unplugged Make sure the dryer plug is pushed completely into
the outlet.
Fuse is blown/circuit breaker Check the building’s fuse/circuit breaker box and is tripped replace fuse or reset breaker. NOTE: Electric dryers
use two fuses or breakers.
Dryer doesn’t heat Fuse is blown/circuit breaker Check the building’s fuse/circuit breaker box and
is tripped; the dryer may tumble replace both fuses or reset both breakers. Your dryer but not heat may tumble if only one fuse is blown or one breaker
tripped.
Gas service is off Make sure gas shutoff at dryer and main shutoff are
fully open.
LP gas supply tank is empty Refill or replace tank. Dryer should heat when utility or there has been a utility service is restored. interruption of natural gas (gas models)
Dryer shakes or Some shaking/noise is normal. Move dryer to an even floor space, or adjust leveling legs makes noise Dryer may be sitting unevenly as necessary until even.
Inconsistent drying times Type of heat Drying time will vary according to the type of heat used.
If you recently changed from an electric to a gas (natural or LP) dryer, or vice versa, the drying time could be different.
Type of load and The load size, types of fabric, wetness of clothes and the drying conditions length and condition of the exhaust system will affect
drying times.
No numbers displayed Dryer is continuously This is normal. When the dryer senses a low level of during cycle, only lights monitoring the amount of moisture in the load, the dryer will display the dry time
moisture in the clothes remaining.
Est. Time Remaining The estimated time may change This is normal. jumped to a when a smaller load than usual lower number is drying
Clothes are still wet The door was opened mid-cycle. A dry cycle must be reselected each time a new load and dryer shut off The load was then removed from is put in. after a short time the dryer and a new load put in
without selecting a new cycle
Small load When drying only a few items, choose SPEED DRY or
TIMED DRY.
Load was already dry except Choose SPEED DRY or TIMED DRY to dry damp collars for collars and waistbands and waistbands. In the future, when drying a load with
collars and waistbands, choose MORE DRY.
Dryer is not level Move dryer to an even floor space or adjust leveling legs
as necessary until even.
Before you call for service… GEAppliances.com
18
OPERATION Possible Causes What To Do
The DRY dryness level Load consists of a mixture When combining heavy and light fabrics in a load, was chosen but load is of heavy and light fabrics choose MORE DRY. still damp
Exhaust system is blocked Inspect and clean exhaust system.
Cannot make a The DRYNESS LEVEL, HEAT This is normal. selection and the SETTING or OPTION that dryer beeps twice you are trying to select is
incompatible with the chosen dry cycle
Dryer is running but The EXTEND TUMBLE This is normal. During extended tumbling, the time 00 is displayed in option was chosen remaining is not displayed. The extended tumbling Est. Time Remaining option lasts approximately 20 minutes.
LAUNDRY PRACTICES Possible Causes What To Do
Clothes are wrinkled Overdrying Select a shorter drying time.
Remove items while they still hold a slight amount of moisture. Select a LESS DRY or DAMP setting.
Overloading Separate large loads into smaller ones.
Letting items sit in dryer after Remove items when cycle ends and fold or hang cycle ends immediately, or use the EXTEND TUMBLE option.
Clothes shrink Some fabrics will naturally shrink To avoid shrinkage, follow garment care labels exactly.
when washed. Others can be safely washed, but will shrink
Some items may be pressed back into shape after drying.
in the dryer
If you are concerned about shrinkage in a particular item, do not machine wash or tumble dry it.
Greasy spots on clothes Improper use of fabric softener Follow directions on fabric softener package.
Drying dirty items Use your dryer to dry only clean items. Dirty items can with clean ones stain clean items and the dryer.
Clothes were not Sometimes stains which cannot be seen when the completely clean clothes are wet appear after drying. Use proper washing
procedures before drying.
Lint on clothes Lint filter is full Clean lint screen before each load.
Improper sorting Sort lint producers (like chenille) from lint collectors
(like corduroy).
Static electricity can attract lint See suggestions in this section under STATIC.
Overloading Separate large loads into smaller ones.
Paper, tissue, etc., left in pockets Empty all pockets before laundering clothes.
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
Before you call for service…
19
LAUNDRY PRACTICES Possible Causes What To Do
Static occurs No fabric softener was used Try a fabric softener.
Bounce®Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions.
Overdrying Try a fabric softener.
Adjust setting to LESS DRY or DAMP.
Synthetics, permanent press Try a fabric softener. and blends can cause static
Collars and waistbands The dryness monitor senses Choose SPEED DRY or TIMED DRY to dry damp collars still wet at end of cycle that the body of the clothes and waistbands. In the future, when drying a load with
is dry collars and waistbands, choose MORE DRY.
Clothes take too long Improper sorting Separate heavy items from lightweight items (generally, to dry a well-sorted washer load is a well-sorted dryer load).
Large loads of heavy fabrics Large, heavy fabrics contain more moisture and take (like beach towels) longer to dry. Separate large, heavy fabrics into smaller
loads to speed drying time.
Controls improperly set Match control settings to the load you are drying.
Lint filter is full Clean lint filter before every load.
Improper or obstructed ducting Check installation instructions for proper
ducting/venting.
Make sure ducting is clean, free of kinks and unobstructed.
Check to see if outside wall damper operates easily.
Check the Installation Instructions to make sure the
dryer venting is correct.
Blown fuses or tripped circuit Replace fuses or reset circuit breakers. Since most breaker dryers use 2 fuses/breakers, make sure both are
operating.
Overloading/combining loads Do not put more than one washer load in the dryer at
a time.
Underloading • If you are drying only one or two items, add a few items
to ensure proper tumbling.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions
GEAppliances.com
20
Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips
Notes.
21
General Electric Company
Warranty Registration Department P.O. Box 32150 Louisville, KY 40232-2150
GE Service Protection Plus
GE, a name recognized worldwide for quality and dependability, offers you Service Protection Plus
—comprehensive protection on all your appliances—
No Matter What Brand!
Benefits Include:
Backed by GE
All brands covered
Unlimited service calls
All parts and labor costs included
No out-of-pocket expenses
No hidden deductibles
One 800 number to call
You will be completely satisfied with our service protection or you may request your money back on the remaining value of your contract. No questions asked. It’s that simple.
Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand! Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable household products are protected against expensive repairs.
Place your confidence in GE and call us in the U.S. toll-free at 800.626.2224 for more information.
*All brands covered, up to 20 years old, in the continental U.S.
We’ll Cover Any Appliance. Anywhere. Anytime.*
Please place in envelope and mail to:
Cut here
22
Consumer Product Ownership Registration
I
m
p
o
r
t
a
n
t
M
a
i
l
T
o
d
a
y
!
General Electric Company Louisville, Kentucky www.GEAppliances.com
First
Name
Mr. Ms. Mrs. Miss
Street
Address
City
State
Date Placed
In Use
Month
Day
Year
Zip
Code
Apt. #
Last
Name
Phone
Number
_
_
Consumer Product Ownership Registration
Dear Customer: Thank you for purchasing our product and thank you for placing your confidence in us. We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
Important: If you did not get a registration card with your
product, detach and return the form below to ensure that your product is registered, or register online at www.GEAppliances.com.
1
23
Model Number Serial Number
Cut here
Complete and mail your Consumer Product Ownership Registration today.
Have the peace of mind of knowing we can contact you in the unlikely event of
a
safety modification.
After mailing the registration below, store this document in a safe place. It contains information you will need should you require service. Our service number is
800.GE.CARES (800.432.2737).
Read your Owner’s Manual carefully. It will help you operate your new appliance properly.
Model Number Serial Number
E-mail Address*
* Please provide your e-mail address to receive, via e-mail, discounts, special offers and other important
communications from GE Appliances (GEA).
Check here if you do not want to receive communications from GEA’s carefully selected partners.
FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR WARRANTY RIGHTS.
For information about GEA’s privacy and data usage policy, go to www.GEAppliances.com and click on “Privacy Policy” or call 800.626.2224.
23
Service trips to your home to teach you how to use the
product.
Improper installation, delivery or maintenance.
Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
Replacement of the light bulb.
Replacement of house fuses or resetting of circuit
breakers.
Damage to the product caused by accident, fire, floods or
acts of God.
Incidental or consequential damage caused by possible
defects with this appliance.
Damage caused after delivery.
What Is Not Covered:
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
Operating InstructionsSafety Instructions Consumer SupportTroubleshooting Tips
All warranty service provided by our Factory Service Centers, or an authorized Customer Care
®
technician. To schedule service,
on-line, 24 hours a day, visit us at GEAppliances.com, or call
800.GE.CARES (800.432.2737).
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
For The Period Of: We Will Replace:
One Year Any part of the dryer which fails due to a defect in materials or workmanship. During this
From the date of the full one-year warranty, GE will also provide, free of charge, all labor and related service costs original purchase to replace the defective part.
Second Year Any part of the dryer which fails due to a defect in materials or workmanship. During this
From the date of the additional one-year limited warranty, you will be responsible for any labor or related service costs. original purchase
Third through Fifth Year The extra large or super capacity dryer drum and main electronic control board if any of these
From the date of the parts should fail due to a defect in materials or workmanship. During this additional three-year original purchase limited warranty, you will be responsible for any labor or related service costs.
GE Dryer Warranty. (For customers in the United States)
Printed in Canada
Consumer Support.
GE Appliances Website
GEAppliances.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals, order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™” your questions, and so much more...
Schedule Service GEAppliances.com
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal business hours.
Real Life Design Studio GEAppliances.com
GE supports the Universal Design concept—products, services and environments that can be used by people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Extended Warranties GEAppliances.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours. GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories GEAppliances.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
Contact Us GEAppliances.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park Louisville, KY 40225
Register Your Appliance GEAppliances.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty, should the need arise. You may also mail in the pre-printed registration card included in the packing material.
Loading...