Page 1
S H R E D D E R S
Instruction Manual
www.accobrandsasia.com
A U T O + 1 0 0 X & 1 0 0 M
™
Page 2
2min
MAX
1
Page 3
3
100X
5
6
2
4
Page 4
Page 5
Sheet capacity:
Manual feed slot
6 sheets (80gsm)
Sheet capacity:
Autofeed chamber
100 sheets (80gsm)
Duty Cycle 5 min ON / 30 min OFF
Run time from cold 10 minutes
Volts / Hz UK Version: 230V / 50Hz
EK Version: 220V / 60Hz
Amperage UK Version: 1.2 Amps
EK Version: 1.2 Amps
Motor Watts UK Version: 200 Watts
EK Version: 300 Watts
Sheet capacity:
Manual feed slot
6 sheets (80gsm)
Sheet capacity:
Autofeed chamber
100 sheets (80gsm)
Duty Cycle 5 min ON / 30 min OFF
Run time from cold 10 minutes
Volts / Hz UK Version: 230V / 50Hz
EK Version: 220V / 60Hz
Amperage UK Version: 1.5 Amps
EK Version: 1.5 Amps
Motor Watts UK Version: 350 Watts
EK Version: 350 Watts
technical specifications
GBC Auto+ 100X GBC Auto+ 100M
A U T O + 1 0 0 X & 1 0 0 M™ S H R E D D E R S
including the “probe accessibility tests”, do not operate the shredder near children or pets.
There is a ‘cross shaped’ integral safety device, located on the left of the internal loading bay, which
is designed to prevent the shredder from operating when the loading door is open. You must NOT
under any circumstances tamper with with this switch, add any object into the cross-shaped interlock
switch other than the interlock actuator, as to do so would activate the cutting blades.
To guard against injury, the following basic safety precautions must be observed in the set-up of this
product.
• Ensure the machine is plugged into an easily accessible power outlet, and ensure the cable is not
likely to trip up a passer by.
•
supplier.
• Unplug your shredder before moving it or when it is not in use for an extended period of time.
• Do NOT operate with a damaged power supply cord or plug, after it malfunctions, or after it has
been damaged in any manner.
•
• The socket-outlet should be near the equipment and should be easily accessible.
•
• Do NOT use near water.
• Do NOT use aerosol dusters or cleaners.
• Do NOT spray anything into the shredder.
• Do NOT load the auto-feed chamber with unopened junk mail, magazines, bound documents etc.
Although this shredder has been designed to comply with UL 60950-1 EN 60950-1 safety standards
points to note
5
GB
Page 6
control panel and indicators
Continuous Jam BoostReverse
Auto
warning symbols
This means no aerosols.
This means keep children away
from shredder.
This means you should be careful
because long hair can become
entangled in the cutting head.
This means don’t reach into the
feed opening of the cutting head.
This means be careful of loose
jewellery which could become
entangeld in the cutting head.
This means no oil lubrication,
use Rexel oil sheets only.
This means be careful of ties and
other loose clothing which could
become entangled in the cutting
head.
This means the shredder can accept
small paperclips. 100M Autofeed ONLY
This means the shredder can accept
small staples. 100M Autofeed ONLY
Safety First
Sheet capacity of manual feed
entry slot.
6
Paper Loading Door/Bin Door
Open or Bin Full indicator –
This means either:
• Loading door is open
• Bin is open
• Bin is full
Paper jam indicator – This means
there is a paper jam in the auto feed
chamber.
shredder is attempting to clear a
paper jam automatically.
If this symbol is permanently
illuminated red please follow the
instructions under ‘Rare Occasions
of Jamming’.
Cool Down indicator – This means
the machine is cooling down.
6
GB
Page 7
Auto+ 100X/100M shredding capability
Auto+ 100X/100M CAN shred the following:
• 100 sheets
•
Stapled paper, 25mm within the corner. 100M Autofeed ONLY
• 26/6 and 24/6 or smaller staples
• Small sized paper loaded centrally
• 100 sheets
• Paper clip paper, 25mm within the corner. 100M Autofeed ONLY
• Capable of shredding small/medium paper clips (max. wire thickness = 0.9 mm)
• >80/100gsm paper (through manual feed slot ONLY)
• A3 folded in half max. 2 sheets
• 100 sheets
• 80 gsm paper
- A4 - 210mm x 297mm
- A5 - 148mm x 210mm
- A3 single sheet folded in half to make A4
Auto+ 100X/100M CAN shred (through the manual feed slot):
Thick paper or
card.
Multiple folded
sheets (e.g. A3
sheets folded in
half).
Unopened mail
(e.g. junk mail).
Glossy paper or
a sheet covered
with print on both
sides.
Auto+ 100X/100M CANNOT shred the following:
Large clips.
Check the length
of the paperclip
is not longer than
32mm.
Heavy duty
staples. Check
the staple leg
length is not
greater than
6mm.
Bound
documents
Bulldog clips
Magazines or
other documents
bound by multiple
staples or clips.
Adhesive labels.
Plastic sheets,
laminated
documents,
plastic folders.
A U T O + 1 0 0 X & 1 0 0 M™ S H R E D D E R S
7
GB
Page 8
1. operation
1 Unpack the product.
2 Connect the shredder to mains supply.
3 Ensure the ON/OFF button on the back of the machine is in the ON position.
4 To commence shredding, press the central Auto button (
). This will illuminate the blue standby
symbol on the auto button, which sets the shredder into auto mode. You are now ready to shred.
5 Press the loading door button to open the loading door. You can open the door further to
90 degrees for easier access if required. Load up to 100 sheets at a time into the feed chamber.
Do not fill above 100 MAX level, this could damage the shredder.
6 Close the loading door without pressing the loading door button. The shredder will now start
automatically. If there is still paper in the Autofeed chamber after first attempt, open and reclose
the paper loading door a second time.
7 If you only have up to 6 sheets to shred, you can use the manual feed slot, provided the auto
feed chamber is empty.
8 Insert paper to be shredded into the feed area. The shredder will detect the paper and start
automatically.
9 If the shredder is left in auto mode for more than 2 minutes without being used, the shredder
will automatically turn back to standby mode in order to save power.
10 The shredder will automatically ‘wake up’ from sleep mode when paper is inserted into the
shred mouth or you open the loading door. There is no need to press the Auto button (
).
autofeed technology
The Auto+ 100X/100M has been designed to automatically shred up to 100 sheets from the autofeed chamber and up to 6 sheets through the manual feed slot. The auto-feed mechanism has
been designed to handle paper fastened with staples and paper clips and to only pull a few sheets
of paper into the cutting mechanism to minimise the risk of paper jams
8
GB
bin or loading door open safety function
As a safety precaution, if the bin or loading door is opened during shredding, the shredder will
stop and the bin full indicator will illuminate (
).
Reverse the paper out then turn the machine off using the ON/OFF switch at the rear of the
) has been fitted for
2. reverse function
1 Should you wish to reverse paper out whilst shredding, a reverse button (
your convenience.
2
shredder. Remove the paper from the manual feed slot (if being used) or open the loading door,
remove the remaining stack of paper, then pull the jammed paper free of the cutting mechanism.
3 To resume shredding, turn the shredder on using the ON/OFF switch at the rear of the shredder.
Return the switch to the auto position (
).
Page 9
the cool down indicator will flash red (
over heating
If the Auto+ 100X/100M is used continuously for over 10 minutes the shredder may overheat and
). Please allow the shredder to cool down. When the
shredder is ready to be used the thermometer symbol will no longer illuminate. If the shredder
needs to cool down while shredding, no action is needed. The shredder will automatically restart
shredding paper once it has cooled down after periods of continuous use. All you need to do is
ensure paper is loaded into the chamber and the bin is empty when the machine is cooling down.
A U T O + 1 0 0 X & 1 0 0 M™ S H R E D D E R S
9
GB
4. self-cleaning cutters
After emptying and replacing a full bin, the shredder will run in forward for 4 seconds, stop for
2 seconds and then reverse for 4 seconds to clear away any remaining paper from the cutter
mechanism. This unique ‘self-cleaning’ mechanism is additional jam prevention technology
from GBC.
5. bin full
The shredder will not function when the bin is full and the bin full symbol ( ) is illuminated.
You should empty the bin.
• Pull open the bin slowly to empty.
• Push the empty bin back into place and press the auto button to resume shredding.
The Auto+ 100X ONLY can shred credit cards, not CDs or DVDs. Switch the shredder to auto mode
and insert the credit card between the markings in the manual feed slot. Only shred one credit card
at a time.
GBC encourages customers to recycle shredded paper.
Please note that shredded paper cannot be recycled if mixed with credit card shards.
If recycling, please separate shredded paper and credit cards.
3. credit card shredding
rare occasions of jamming
If after this auto jam clearance cycle the shredder still has a paper jam, it will stop and the jam
indicator illuminate (
). Try clearing the jam using the reverse (
) and continuous jam boost
( ) buttons. If this is unsuccessful follow the reverse fuction instructions to clear any jammed
material.
automatic jam clearance
In the unlikely event of the shredder jamming, the Auto+ 100X and 100M will automatically reverse
and forward the engine three times to clear a jam. During this operation the Paper Jam indicator will
).
Page 10
lubrication of the shredder
Only use Rexel Oil Sheets (2101948) to lubricate. ACCO Brands accepts no liability for
product performance or safety when other types or brands of lubricants are used on any part(s) of
this machine. GBC recommend using an oil sheet after the bin has been emptied three times (and
for ongoing three bin cycle thereafter). Insert the oil sheet into the manual feed slot and NOT in the
auto-feed chamber. Using an oil sheet in the auto-feed chamber will contaminate the feed rollers
preventing the auto-feed mechanism shredding. Follow the maintenance instructions if the rollers
become contaminated.
10
GB
Only use Rexel Oil Sheets* (2101948) to
lubricate.
Oil Sheets
shredder accessories
Accessory Part Number Quantity
2101948 12 sheets/pack
ACCO Brands (ACCO) warrants its products and their parts against defects in materials and workmanship under normal
use for a period of 12 months from the original date of purchase. During this period, ACCO will, at its discretion, in
accordance with law, either repair the shredder using new or refurbished parts, or replace the shredder with a new or
refurbished shredder that is equivalent to the shredder being replaced. The warranty applies only to defects in materials
and workmanship under normal use and does not extend to damage to the product or parts which result from:-
- alteration, repair, modification or service carried out by anyone other than an authorised ACCO service centre.
- accident, neglect, abuse or misuse owing to failure to comply with the normal operating procedures of the product.
Please note that the cutter blades will be progressively worn down by shredding fastened sheets (staples and paperclips)
- this is not covered in the warranty. The Auto+ 100X has been design to shred up to 25 credit cards in the standard 1 year
warranty period. Any excessive credit card shredding will invalidate the cutter warranty. Auto+ 100X has NOT been
designed to shred CDs or DVDs, any attempt to do so will invalidate this warranty.
guarantee
* ACCO Brands accepts no liability for product performance or safety when other types or brands of lubricants are used on
any part(s) of this machine.
The rollers on the auto-feed mechanism may become dirty over time, please wipe clean with a
dry cloth to maintain maximum product performance.
The auto-start infra-red sensor, located in the paper feed entry-slot, can occasionally become
covered in paper-dust causing the shredder to run despite no paper being fed into the
machine. Switch the shredder off at the rear of the machine and carefully clean the sensor
using a cottonswab.
6. maintenance
1
2
Page 11
Page 12
ACCO BRANDS ASIA PTE LTD
5A Toh Guan Road East
#06-03 Singapore 608830
Tel: +65 6776 0195
Fax: +65 6779 1041
Singapore.webmaster@acco.com
Ref:AUTO+100X-100M/SG/V2/200314
Certificate of Warranty
(For use in Singapore only)
Model :
Serial No. :
Validity : 1 year from date of purchase
IMPORTANT: Certificate of Warranty must be produced together with proof of
purchase (e.g. sales invoice, receipts, etc) when your equipment requires our
service. All services provided after warranty period will be chargeable.
Terms and conditions
ACCO Brands Asia hereby certify that all machines of whatever designs are free
from any defects in materials and in workmanship under normal use and service for
twelve (12) months from date of purchase. Should any defects occur within the
aforesaid period, ACCO Brands Asia shall at their absolute discretion, effect repairs
or replacement of any part of the said machine free of costs.
1. This warranty shall not be transferable, negotiable or assignable to any third
party.
2. This warranty shall be considered VOID under the following circumstances:
a. The serial number of the machine has been altered or removed.
b. The machine has been subjected to misuse, accident, and negligence.
c. The machine has not been installed, maintained or operated in
accordance with the instructions given in the instruction manual.
d. The machine has undergone repairs, adjustments or corrections made to
it by unauthorised person.
e. The machine has been dismantled by unauthorised person.
3. This warranty is applicable only in Singapore.
4. This warranty shall exclude all faults/defects caused by natural wear and tear.
5. This warranty shall exclude all other warranties & guarantees, expressed or
implied other than mentioned above.
6. No notices will be given on expiry of this warranty. ACCO Brands Asia reserves
the rights to amend or modify the terms and conditions of this warranty without
giving any prior notice.
CARRY-IN
WARRANTY
No. 200314
Loading...