Garmin Tri-Tronics PRO70, Pro 70 Owner's Manual

Getting Started

WARNING

See the Important Safety and Product
Information guide in the product box for

product warnings and other important
information.

Setting Up the Pro 70 System

Before you can use the Pro 70 system,
you must set up the devices.

1

Attach the dog collar device to the
collar strap (page 3).

2

Charge the handheld device
(page 3).

3

Charge the dog collar device
(page 4).

4

Turn on the devices (page 5).

5

If necessary, pair the dog collar device
with the handheld device (page 5).

Device Overviews

Pro 70 Handheld Device

À

Intensity level and training mode dial

Á

Battery level

Â

Dog collar device toggle switch

Ã

Training keys

2

Pro 70 Dog Device

À

Power key

Á

Status LED

Â

Lights

Ã

Contact points

Ä

Charging clip contacts

Attaching the Dog Collar Device to
the Collar Strap

1

With the buckle

À

facing outward,
insert the end of the collar strap
through the slot Á on the collar
device.

2

Pull most of the collar strap through
the two slots

Â

on the dog device.

3

Insert the end of the collar strap
through the slot

Ã

on the opposite

side of the device.

4

Pull the strap until it is tight across the
front of the device.

Charging the Handheld Device

You should fully charge the battery before
you use the device for the first time or
whenever the battery is low (page 11). It
is normal for the battery to discharge in
approximately 7 to 10 weeks when the
device is not in use. Charging a fully
depleted battery takes about 2 hours.

NOTE: The device will not charge when it
is outside the temperature range of 32° to
104°F (0° to 40°C).

1

Lift the weather cap

À

.

3

2

Plug the small end of the power cable
into the mini-USB port

Á

on the

device.

3

Plug the other end of the power cable
into an appropriate power source.

The status LED is solid red when the
device is charging.

4

After the status LED turns solid green,
unplug the power cable from the
device.

Charging the Collar

NOTICE

To prevent corrosion, thoroughly dry the
contacts on the collar and the surrounding
area before connecting the charging clip.

You should fully charge the battery before
you use the device for the first time or
whenever the battery is low (page 11). It
is normal for the battery to discharge in
approximately 7 to 10 weeks when the
device is not in use. Charging a fully
depleted battery takes about 2 hours.

NOTE: The device will not charge when
outside the temperature range of 32° to
104°F (0° to 40°C).

1

Snap the charging clip

À

onto the

device Á.

4

2

Plug the power cable into a power
source.

The status LED is solid red when the
collar is charging.

3

After the status LED turns solid green,
remove the charging clip from the
collar.

Turning On the Dog Collar Device

• On the dog collar device, hold the
power key until the status LED turns
green and the collar beeps to turn it
on in training mode.

• On the dog collar device, hold the
power key until the status LED turns
blue to turn on the BarkLimiter™
feature (page 9).

• On the dog collar device, hold the
power key until the status LED turns
yellow to enter pairing mode
(page 5).

Turning Off the Device

1

On the dog collar device, hold the
power key until the red LED appears.

2

Release the power key.
The dog collar device beeps to

confirm powering off.
NOTE: If the device is powered off in

BarkLimiter mode, the LED flashes
the number of corrected barks before
powering off (page 10).

Dog Collar Device

You can use up to 6 dog collar devices
with a single handheld device.

Each dog collar device must be paired
with the handheld device before it can be
used. During the pairing process, each
dog collar device is associated with a
different color on the handheld device.

Pairing a Dog Collar Device with the
Handheld Device

NOTE: If your handheld device and dog
collar device were included in the same

5