All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written
consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of
this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin
.com for current updates and supplemental information concerning the use of this product.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its
products and to make changes in the content without obligation to notify any person or organization of such changes
or improvements. Go to the Garmin Web site (www.garmin.com) for current updates and supplemental information
concerning the use and operation of this and other Garmin products.
Table of Contents
Getting Started ����������������������������������������� 1
Connecting the Device to Vehicle Power ........... 1
About myDashboard .......................................... 2
About Sleep Mode ............................................. 4
Adjusting the Screen Brightness .......................4
Adjusting the Volume ......................................... 4
Status Bar Icons ................................................ 5
Index ������������������������������������������������������� 57
nüvi 140/150 Series Owner’s Manual iii
Getting Started
See the Important Safety and Product
Information guide in the product box for product
warnings and other important information.
Connect the device to vehicle power
1
(page 1).
Mount the device (page 1).
2
Register the device (page 3).
3
Check for updates.
4
• Software updates (page 3).
• Free map update (page 3).
nüvi 140/150 Series Owner’s Manual 1
WARNING
Connecting the Device to Vehicle
Power
This product contains a lithium-ion battery.
To prevent the possibility of personal injury or
product damage caused by battery exposure
to extreme heat, remove the device from the
vehicle when exiting or store it out of direct
sunlight.
Before you use your device on battery power,
you should charge it.
Plug the vehicle power cable ➊ into the
1
USB port on the device
Snap the mount ➌ onto the suction cup ➍.
2
Press the suction cup to the windshield, and
3
ip the lever
Fit the bottom of your device into the mount.
4
Tilt your device back until it snaps into place.
5
WARNING
➋.
➎ back toward the windshield.
➌
➍
➊
➎
Plug the other end of the vehicle power
6
cable into a power outlet in your vehicle.
➋
About myDashboard
Use myDashboard to registeryour device, check
for software and map updates, access product
manuals and support, and more.
Setting Up myDashboard
Connect the USB cable➊to the USB port
1
➋on the device.
➊
Connect the USB cable to the USB port on
2
your computer.
Go to www.garmin.com/dashboard.
3
Follow the on-screen instructions.
4
2 nüvi 140/150 Series Owner’s Manual
➋
Registering the Device
Open myDashboard (page 2).
1
Follow the on-screen instructions.
2
Updating the Software
Open myDashboard (page 2).
1
Under Software Updates, click Update Now.
2
Follow the on-screen instructions.
3
nüMaps Guarantee
If you register through myDashboard, your
device could be eligible for one free map update
within 90 days of rst acquiring satellites while
you drive. Go to www.garmin.com/numaps for
details and terms and conditions.
nüvi 140/150 Series Owner’s Manual 3
™
Updating Maps
Open myDashboard (page 2).
1
Register the device (page 3).
2
Under Map Updates, click Update Now.
3
If a free map update is no longer available,
click Buy Now.
Follow the on-screen instructions.
4
Turning Off the Device
You can turn off the device completely.
Hold the Power key ➊ for 3 seconds.
1
➊
NOTE: If you hold the Power key for less
than 3 seconds, the device enters sleep
mode (page 4).
Select Off.
2
Resetting the Device
You can reset your device if it stops functioning.
Hold the Power key for 10 seconds.
About Sleep Mode
Use sleep mode to conserve battery power
when your device is not in use. Sleep mode
uses very little power, and a battery charge lasts
for weeks when your device is in sleep mode.
Adjusting the Screen Brightness
Select Settings > Display > Brightness.
1
Use the slider bar to adjust the brightness.
2
Adjusting the Volume
Select Volume.
1
Select an option:
2
• Use the slider bar to adjust the volume.
• Select
• Select
slider bars to adjust the volume for
navigation prompts, phone, and media.
to mute the device.
> Audio Mixer and use the
Entering Sleep Mode
Press the Power key.
Exiting Sleep Mode
While the device is in sleep mode, Press the
Power key.
4 nüvi 140/150 Series Owner’s Manual
Status Bar Icons
The status bar is located at the top of the main
menu. The status bar icons display information
about features on the device. You can select
some icons to change settings or view additional
information.
GPS signal status.
Transportation mode indicator.
Current time.
Battery status.
nüvi 140/150 Series Owner’s Manual 5
Satellite Signals
After the device is turned on, it begins acquiring
satellite signals. The device may need a clear
view of the sky to acquire satellite signals. When
at least one of the
device has acquired satellite signals.
For more information about GPS, go to
www.garmin.com/aboutGPS.
Viewing GPS Signal Status
Hold for three seconds.
bars is green, your
Transportation Modes
Automobile mode
Pedestrian mode
Routing and navigation are calculated differently
based on your transportation mode.
For example, in Automobile mode, the estimated
time of arrival is calculated using the speed
limit of the roads on the route. Pedestrian mode
calculates time of arrival based on walking
speed.
Choosing a Transportation Mode
Select
6 nüvi 140/150 Series Owner’s Manual
or .
Battery Information
After the device is connected to power, it begins
to charge.
in the status bar indicates the status of the
internal battery. To increase the accuracy of the
battery gauge, you should fully discharge the
battery and then fully charge it. Do not unplug
the device until it is fully charged.
Using the On-screen Buttons
• Select to return to the previous screen.
• Hold
• Select
• Hold
• Select
to quickly return to the main menu.
or to see more choices.
or to scroll faster.
to see a menu of options for the
current screen.
Using the On-screen Keyboard
See “Language and Keyboard Settings” to
change the keyboard layout (page 47).
• Select a character on the keyboard to enter
a letter or number.
• Select
• Select
• Select
• Select
mode.
• Select
such as punctuation marks.
• Select
capitalization.
nüvi 140/150 Series Owner’s Manual 7
to add a space.
to delete an entry.
to delete a character.
to select the keyboard language
to enter special characters,
to change character
About Shortcuts
You can add shortcuts to the Where To? menu.
A shortcut can point to a location, a category, or
a search tool.
Adding a Shortcut Icon
The Where To? menu can contain up to 36
shortcut icons.
Select Where To? > Add Shortcut.
1
Select an item.
2
Removing a Shortcut
Select Where To > > Remove
1
Shortcut(s).
Select the shortcut to remove.
2
Select the shortcut again to conrm.
3
Finding Locations
The device offers many methods for nding
locations.
• By category (page 8)
• Near another location (page 10)
• By spelling the name (page 11)
• By address (page 11)
• Using the map (page 12)
• Using recently found locations (page 13)
• Using coordinates (page 12)
• Using the map (page 12)
• Using saved locations (page 14)
8 nüvi 140/150 Series Owner’s Manual
About Locations
The detailed maps loaded in your device contain
locations, such as restaurants, hotels, and auto
services. You can use the Categories function to
browse for nearby businesses and attractions.
Finding a Location by Category
Select Where To?.
1
Select a category, or select Categories.
2
If necessary, select a subcategory.
3
Select a location.
4
Searching Within a Category
To narrow your search results, you can search
within some categories.
Select Where To?.
1
Select a category, or select Categories.
2
If necessary, select a subcategory.
3
Select the search bar ➊.
4
➊
Enter all or part of the name.
5
Select .
6
Finding a Location Using the Search Bar
You can use the search bar to search for
locations by entering a category, brand name,
address, or city name.
Select Where To?.
1
Select the search bar.
2
Enter a search term.
3
Suggested search terms appear below the
search bar as you type.
Select an option:
4
• To search for a type of business, enter a
category name, such as “movie theaters” or
“coffee shops.”
nüvi 140/150 Series Owner’s Manual 9
• To search for a business by name, enter
all or part of the name.
• To search for an address near you, enter
the street number and street name.
• To search for an address in another city,
enter the street number, street name,
city, and state.
• To search for a city, enter the city and
state.
• To search for coordinates, enter latitude
and longitude coordinates.
Select an option:
5
• To search using a suggested search
term, select the term.
• To search using the text you entered,
select
If necessary, select a location.
6
.
Changing the Search Area
By default, your device nds locations closest
to your current location. You can nd a location
near another city or location.
Select Where To? > Searching Near.
1
Select an option.
2
If necessary, select a location.
3
Reporting a Closed or Missing Location
If your search results include an outdated or
incorrect location, you can report the error to
Garmin and remove the location from future
searches.
Find a location (page 8).
1
Select a location from the list.
2
Select .
3
Select > Edit.
4
Select Report as Closed or Report as
5
Missing.
10 nüvi 140/150 Series Owner’s Manual
Editing Location Information
You can change the address or phone number
for a location that appears in the search results.
Find a location (page 8).
1
Select a location from the list.
2
Select .
3
Select > Edit.
4
Select Address or Phone Number, and
5
enter the new information.
Rating a Point of Interest
You can assign a star rating to a point of
interest.
Find a location (page 8).
1
Select > .
2
Select the stars to rate the point of interest.
3
The star rating updates on your device.
About Search Tools
Search tools allow you to search for cities,
addresses, intersections, or coordinates. By
default, the address search tool appears in
the Where To? menu. To search for cities,
intersections, and coordinates, you must add
those search tools to the Where To? menu
(page 7).
Finding an Address
NOTE: The order of the steps may change
depending on the map data loaded on your
device.
Select Where To? > Address.
1
Enter information as prompted by the on-
2
screen instructions.
If necessary, select Searching Near, and
3
enter a different city or postal code.
If necessary, select the address.
4
nüvi 140/150 Series Owner’s Manual 11
Finding a City
Before you can nd a city, you must add the city
search tool to the Where To? menu (page 7).
Select Where To? > Categories > Cities.
1
Select Enter Search.
2
Enter a city name, and select .
3
Select a city.
4
Finding an Intersection
Before you can nd an intersection, you must
add a shortcut to the intersection search tool
(page 7).
Select Where To? > Categories >
1
Intersections.
Select a state or province.
2
NOTE: If necessary, select State or Country
to change the country, state, or province.
Enter the rst street name, and select Next.
3
If necessary, select the street.
4
Enter the second street name, and select
5
Next.
If necessary, select the street.
6
If necessary, select the intersection.
7
Finding a Location Using Coordinates
You can nd a location using latitude and
longitude coordinates. This method can be
helpful when geocaching.
Select Where To? > Categories >
1
Coordinates.
If necessary, select > Format, select the
2
correct coordinate format for the type of map
you are using, and select Save.
Select the latitude coordinate.
3
Enter the new coordinate, and select Done.
4
Select the longitude coordinate.
5
Enter the new coordinate, and select Done.
6
Select View on Map.
7
12 nüvi 140/150 Series Owner’s Manual
Finding a Location by Browsing the Map
Before you can nd places included in the map
data, such as restaurants, hospitals, and fuel
stations, you must enable the map layer for
places along the road (page 22).
Select View Map.
1
Select the screen.
2
Drag and zoom the map to display the area
3
to search.
Location markers appear on the map for
places along the road.
If necessary, select , and select a
4
category icon to view only a specic
category of places.
Select an option:
5
• Select a location marker.
• Select a point, such as a street,
intersection, or address location.
If necessary, select the location description
6
to view additional information.
Finding a Location Using Quick Search
After you have performed a search for a point
of interest, certain categories may display a
Quick Search list that displays the last four
destinations you selected.
Select Where To?.
1
Select a category, or select Categories.
2
If applicable, select a destination from the
3
Quick Search list.
If necessary, select the appropriate
4
destination.
Select Enter My Address, Use My Current
2
Location, or Recently Found.
The location is saved as “Home” in the Saved
folder (page 14).
Going Home
Select Where To? > Go Home.
Editing Your Home Location Information
Select Where To? > Saved > Home.
1
Select > Edit.
2
Enter your changes.
3
Select Done.
4
Finding Recently Found Places
Saving a Home Location
You can set your home location for the location
you return to most often.
Select Where To? > > Set Home
1
Location.
nüvi 140/150 Series Owner’s Manual 13
Your device stores the last 50 locations you
have found.
Select Where To? > Recent.
1
Select a location.
2
Clearing the List of Recently Found Places
Select Where To? > Recent >
> Yes.
> Clear
The address of the location appears at the
bottom of the screen.
Select the address.
5
Select Set Location.
6
Finding Parking
You can nd detailed parking information and
pricing information.
Select Where To? > Categories > Parking.
1
Select a parking location.
2
Setting a Simulated Location
If you are indoors or not receiving satellite
signals, you can use the GPS to set a simulated
location.
Select Settings > Navigation.
1
Select GPS Simulator.
2
Select View Map.
3
Select an area on the map.
4
14 nüvi 140/150 Series Owner’s Manual
Saving Locations
You can save locations so you can quickly nd
them and create routes to them.
Saving a Location
Find a location (page 8).
1
Select a location from the list.
2
Select .
3
Select > Save.
4
If necessary, enter a name, and select Done.
5
Saving Your Current Location
From the map, select the vehicle icon.
1
Select Save.
2
Enter a name, and select Done.
3
Select OK.
4
Starting a Route to a Saved Location
Select Where To? > Saved.
1
If necessary, select a category, or select All
2
Categories.
Select a location.
3
Select Go!.
4
Editing a Saved Location
Select Where To? > Saved.
1
If necessary, select a category.
2
Select a location.
3
Select .
4
Select > Edit.
5
Select an option:
6
• Select Name.
• Select Phone Number.
nüvi 140/150 Series Owner’s Manual 15
• To assign categories to the Favorite,
select Categories.
• To save a photo with the Favorite, select
Assign Photo (page 33).
• To change the symbol used to mark the
Favorite on a map, select Change Map Symbol.
Edit the information.
7
Select Done.
8
Assigning Categories to a Saved
Location
You can add custom categories to organize your
saved locations.
NOTE: Categories appear in the saved locations
menu after you have saved more than 12
locations.
Select Where To? > Saved.
1
Select a location.
2
Select .
3
Loading...
+ 47 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.