Gaggenau VI491610 Specs
VI 491 610
Stainless steel frame
Width 36" (90 cm)
Installation accessories
In combination of several Vario
cooktops, connecting strips must be
used.
Choose respective VA 420 strip from
one of the below, depending on type
of installation.
VA 420 010
Connection strip for surface-mount
installation without appliance cover.
VA 420 011
Connection strip for surface-mount
installation with appliance cover.
VA 420 000
Connection strip for flush installation
without appliance cover.
VA 420 001
Connection strip for flush installation
with appliance cover.
VA 450 900
36" stainless steel adjustment strip.
Necessary accessory in a combination of 15" Vario(s) with at least one
cover adjacent to a 36" cooktop.
VA 450 strip will compensate the
appliance depth.
Optional accessories
GN 340 230
Gastronorm roaster
Non-stick cast-aluminum
4" deep, with 2 ½" lid, GN ⅔
(For use on center zone)
GP 900 001
Stainless steel 6" frying pan
Non-stick coating.
GP 900 003
Stainless steel 8" frying pan
Non-stick coating.
Vario 400 series induction cooktop
VI 491
– Five cooking zones with Power
boost for cookware with a diameter
of 5" to 13"
– Solid stainless steel control knobs
– Precision-crafted ⅛-inch stainless
steel frame
– For surface-mount installation with
a visible edge or for flush
installation
– Can be perfectly combined with
other Vario 400 series products
Cooking zones
1 induction cooking zone ø 8"
(2,200 W, with Power boost 3,300 W),
automatically switches to ø 10"
(2,600 W, with Power boost 3,400 W)
and to ø 13" (3,300 W, with Power
boost 4,600 W).
1 induction cooking zone ø 8"
(2,200 W, with Power boost 3,300 W).
2 induction cooking zones ø 7"
(1,800 W, with Power boost 2,500 W).
1 induction cooking zone ø 6"
(1,400 W, with Power boost 1,800 W).
Operation
Control knobs with illuminated
ring, cooking zone and output level
markings.
Electronic control in 12 output levels.
Features
Cooking zone marking.
Power boost function for each
cooking zone.
Poser boost function for ø 13"
cooking zone with 4.6 kW.
Pan detection.
Short-term timer.
Safety
Individual residual heat indication.
Safety lock.
Planning notes
Depending on the type of installation —
surface- or flush-mounted, with or
without cover — the specific location of
the control knob positions may vary.
When using the appliance cover
VA 440 for an adjacent 15" Vario
cooktop and adjustment strip VA 450,
additional space for cut-out depth
needs to be considered.
In a combination of Vario cooktops
with at least one appliance cover, the
adjustment strip VA 450 is required.
In a combination of several Vario 400
series cooktops a connection strip
must be used.
Depending on the type of installation—
surface- or flush-mounted, with or
without cover — the respective VA 420
connecting strip must be used.
For flush installation the edge height
in the cut-out needs to be at least ½"
and for surface-mount ⅜". Ensure a
continuous cut surface of 90°.
The weight capacity and stability,
especially in case of thin counter tops,
must be supported using suitable
substructures. Take the appliance
weight and additional loads into
account.
Flush installation is possible in
countertops made of stone, synthetics
or solid wood. Heat resistance and
watertight sealing of the edges must
be observed. For other materials,
please consult with your countertop
manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the countertop cut-out.
If installing several Vario products
in individual cut-outs allow for a
minimum distance of 2" in between
the cooktops.
Operates with magnetic (induction)
iron pots and pans only. For an optimal
heat distribution, the use of sandwich
bottom cookware is recommended.
Immersion depth depending on
installation situation, 2 ⅝" for surface-
mount or 2 ¼" for flush-mount.
Built-in control panel can be inte grated
in the bottom cabinet at drawer level.
Panel thickness ⅝" – 1".
The adjacent drawing “Installation of
the control knob” must be observed, if
the panel is more than 1" thick. There
must be a recess at the rear for proper
control module installation.
A combination with V 414 downdraft is
not recommended due to insufficient
air extraction from the center zone.
Appliance can be snapped into the
countertop from above.
Please read additional planning notes
on pages 82 – 87.
Please read the installation details
regarding air ducting on page 121.
Rating
Total rating: 10.8 kW.
Total Amps: 45 A.
208/220–240 V / 60 Hz
Plan for a 37" connecting cable
without plug (hardwire required).
39" (1 m)
min. 2"
(50)
min. 41/4" (109)
max. 61/2" (166)
min. 13/8" (35)
R 3/16"
(R 5+1)
R 1/8" (R 3)
1/8
"
(3.5
-0.5
)
dia. 13/8" (35)
dia. 21/8"
(60)
90°
34
15
/
±1
/
(
887
±2
)
36"
+1
/
"
(
914
+2
)
20
1
/
" (520)
*21
1
/
" (*535)
35
3
/
"
(908)
19
3
/
±1
/
(492
±2
)
*20
1
/
+1
/
(*515
+2
)
20
11
/
+1
/
(526
+2
)
*21
1
/
+1
/
(*541
+2
)
3
9
/
" (90)
(90)
(90)
(90)
1
/
" (3)
**2
3
/
" (70)
18" (456)
20" (
508)
2
13
/
"
(72) 3"
(76)
39" (1 m)
min. 2"
(50)
min. 41/8" (105)
max. 63/8" (162)
min. 13/8" (35)
R 1/8" (R 3)
90°
dia. 13/8" (35)
dia. 21/8"
(60)
1
/
" (3)
34
15
/
±1
/
(
887
±2
)
20
1
/
" (*21
1
/
")
520 (*535)
35
3
/
"
(908)
**2
5
/
" (67)
19
3
/
±1
/
(492
±2
)
*20
1
/
+1
/
(*515
+2
)
3
9
/
"(90)
(90)
(90)
(90)
18" (456)
20" (
508)
2
13
/
" (72)
3"
(76)
Surface-mount Installation
Installation of the control knob, surface installation
Installation of the control knob, flush installation
fill with
Longitudinal section
201/2"
View from above
+1
8
8
4
2
8 "
4 "
16 "
16 "
16
Flush-mount Installation
4
4
16 "
8 "
16 "
4 "
2
16
8
16 "
4 "
16 "
16 "
16
16 "
16 "
16
* with adjustment strip. See separate planning notes on page 87.
** 3 ⁹⁄₁₆"(93) in the area of the wire connection (rear, right).
Installation of the control knob; surface-mount installation
1
4
/8"- 63/8"
(105-162)
dia. 1
(35)
D=1" (26)
3
/8"
min.
41/8"- 63/8"
(105-162)
3
/16"
(5)
(16-26)
5
/8"-1"
dia. 13/8"
(35)
min.
3
/16"
(5)
1
/8"-211/4"
3
(80 x 540)
D>1" (>26)
16
16 "
16 "
16
16
* with adjustment strip. See separate planning notes on page 87.
** 3 ¹¹⁄₁₆"(93) in the area of the wire connection (rear, right).
Installation of the control knob; flush-mount installation
1
4
3
/16"
min.
(5)
5
/8"-1"
(16-26)
View from above
/4"-61/2"
(109-166)
dia. 13/8"
(35)
3
19
/8"±1/16" (492±2)
1
*20
3
/16"
min.
(5)
1
3
(80 x 540)
/16" (914+2)
36"
15
/16" ±1/16" (887±2)
34
/4"+1/16" (*515+2)
/8"-211/4"
D=1" (26)
D>1" (>26)
1
/8"
R
(3)
41/4"-61/2"
(109-166)
dia. 13/8"
(35)
R 3/16"
(5+1)
Numbers indicated
inside parenthesis ( ) = mm
11
20
/16" +1/16" (526+2)
*211
/4" +1/16" (*541+2)
* with adjustment strip.
Longitudinal section
1
(3
17
/32"
(13.5)
/8"
+1
)
35
34
3
/4" (908)
15
/16" ±1/16"
(887±2)
+1
36"
(914+2)
/16"
1
(3
/8"
+1
)
17
(13.5)
/32"
silicone
1
/8" (3.5
-0.5
)
Cross-section
fill with
silicone
1
/8" (3.5
-0.5
)
19
20
(520)
3
/8"±1/16"
(492
11
/16"+1/16"
(526
1
/8"
(3+1)
11
/16"
(17)
±2
)
+2
)
1
/8"
(3+1)
11
/16"
(17)
When installating with appliance cover or adjustment strip, pay attention
to the deeper cut-out and the front and rear groove width.
Loading...