Gaggenau VI414-110 Specifications Sheet

VI 414 110

Stainless steel frame
Width 38 cm

Installation accessories
VA 420 010

Connection strip for combination with
other Vario appliances of the 400
series for surface installation

VA 420 011

Connection strip for combination with
other Vario appliances of the 400
series for surface installation with
appliance cover/adjustment strip

VA 420 000

Connection strip for combination with
other Vario appliances of the 400
series for flush installation

VA 420 001

Connection strip for combination with
other Vario appliances of the 400
series for flush installation with
appliance cover/adjustment strip

VA 440 010

Stainless steel appliance cover with
mounting strip

VA 450 400

Stainless steel adjustment strip 38 cm
Required accessory for combination of
several Vario appliances of the 400
series with at least one appliance cover
to compensate the appliance depth.

Special accessories
WP 400 001

Wok pan made of multiple-layer
material
With round bottom and handle,
ø 36 cm, 6 litres, height 10 cm.

WZ 400 001

Wok attachment for wok pan
Only for VI 414.

230V/50Hz

Vario induction wok 400 series

VI 414

– 28 cm cooking zone with booster

function

– Ideal for the original wok pan with

round bottom, with wok ring
– Solid stainless steel control knob
– Precision crafting of 3 mm stainless

steel
– For surface installation with a

visible edge or for flush installation
– Can be combined perfectly with

other Vario appliances of the

400 series

Cooking zones

1 induction wok zone ø 18 cm (1800 W,
with booster 2500 W), which
automatically expands to ø 28 cm
(2800 W, with booster
3600 W).

Handling

Control knobs with illuminated ring,
cooking zone and output level
markings.
Electronic control in 12 output levels.

Features

Cooking zone marking.
Booster function for each cooking
zone.
Pot detection with automatic activation
of the outer cooking zone.
Timer.

Safety

Residual heat indication.
Safety lock.

Planning notes

Depending on the type of installation
(surface-mounted or flush-mounted,
with or without an appliance cover), the
specific location of the cut-out and the
knob positions may vary.
If installing with the appliance cover
VA 440 or adjustment strip VA 450 take
into account the additional space
required for the depth.
If combining several appliances with at
least one appliance cover, the
adjustment strip VA 450 is required to
compensate for the depth of the
appliance without the appliance cover.
If combining several Vario appliances
of the 400 series, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
In the cut-out, the installation system
requires the side edge to be at least
10 mm for surface installation and at
least 13 mm for flush installation.
Ensure a continuous cut surface of
90°.
The bearing capacity and stability, in
the case of thin worktops in particular,
must be supported using suitable
substructures. Take into account the
appliance weight and additional loads.
Additional instructions for flush
installation:
Installation is possible in worktops
made of stone, synthetics or solid
wood. Heat resistance and watertight
sealing of the cut edges must be
observed. Concerning other materials
please consult the worktop
manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.

The joint width may vary due to size
tolerances of the combinations and of
the worktop cut-out.

Please read additional planning notes
on pages 82 - 87.

If installing several appliances in
individual cut-outs allow for a division
bar of minimum 50 mm between the
individual cut-outs.
Operates with magnetic (induction)
iron pots and pans only. For an optimal
heat distribution, the use of sandwich
bottom cookware is recommended.
Immersion depth depending on
installation situation 54/57 mm.
Built-in control panel to be integrated
in the bottom cabinet at drawer level.
Panel thickness 16 – 26 mm.
The drawing "Installation of the control
knob" must be observed if the panel is
more than 26 mm thick (there must be
a recess at the rear).
Appliance can be snapped into the
worktop from above.
Appliance weight: approx. 7 kg.

Connection

Total connected load 3.6 kW.
Connecting cable 1.5m without plug.

Cooking with induction:

Magnetic induction cooking requires
cooking vessels with a ferro-magnetic
base. To see if your cookware is
suitable, simply test it with a permanent
magnet - if the magnet is attracted to
the base, the utensil is suitable for
induction cooking.

Induction cooktop safety note:

Please refer to inside back cover.

66 Vario cooktops

-0.5

View from above

Vario cooktops 67