Fysic FD-110 User manual

FD-110 Installation

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with
double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

2

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.

Press lightly the battery
holder at side

CR2032 3V Lithium Battery

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with
double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.

Press lightly the battery
holder at side

CR2032 3V Lithium Battery

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

Press lightly the battery
holder at side

CR2032 3V Lithium Battery

Indoor-unit:

Outdoor-unit:

Connecting:

Press lightly the battery
holder at side

CR2032 3V Lithium Battery

CODE

MODE

3 sec.

VOL

CODE

MODE

VOL

Service Help

WWW.FYSIC.COM
[e-mail]

NL 073 6411 355

(Lokaal tarief)

BE 03 238 5666

(Lokaal tarief)
(Tarif local)

DE 0180 503 0085

Lokale Festnetzkosten

Hesdo, Australiëlaan 1
5232 BB, ‘s-Hertogenbosch

The Netherlands

Lamp, Ring, Lamp & Ring:

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

CODE

MODE

RESET

<10 sec.

Max. 60

CODE

MODE

VOL

5 sec.

VOL

Change melody:

Frequency: 433MHz ASK
Transmission power: <10mW
Declaration of conformity:

CODE

MODE

VOL

1x

1x

melody-1

~

melody-36

CODE

MODE

VOL

1x
Volume H

Volume M

Volume L

http://DOC.hesdo.com/FD-110-DOC.pdf

Service

Help

WWW.FYSIC.COM
[e-mail]

NL 073 6411 355

BE 03 238 5666

DE 0180 503 0085

Hesdo, Australiëlaan 1, 5232 BB,
‘s-Hertogenbosch,

(Lokaal tarief)

(Lokaal tarief)
(Tarif local)

(Lokale Festnetzkosten)

The Netherlands

v1.0