FUTABA R6008HS, R6014HS User Manual

Usage condition on "High Speed mode"

󾻯

CAUTION

󾻫

Outputs fr om 1ch to 6ch accept the
digita l ser vos only or mos t type of

peripherals.

• If any analog ser vos connected to these output

as it wi ll cause malfunction . P leas e che ck the
peripherals if there's any malfunction with whole
stick lever throw. If any malfunction occur please
change the operation mode to "Normal mode."

• Output of other channels shown below allow to
use any type of servos.

R6008HS - 7ch and 8ch
R6014HS - 7ch to 12ch, DG1, DG2

TM8

(on 8ch mode)

, TM10

(on 10ch mode)

, TM14

(on multi-ch mode)

R6008HS/R6014HS

Compliance Information Statement
(for U.S.A.)

This device, trade name Futaba Corporation of America, model
number R6008HS/R6014HS, complies with part15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL [phone] or E-mail: [e-mail] (Support)
TEL [phone] or E-mail: [e-mail] (Service)

R6008HS/R6014HS Speci­cations

• Dual antenna diversity

• Power requirement: 4.8V or 6.0V battery
or regulated output from ESC, etc. (*1)

• Size : R6008HS: 0.98 x 1.8 6 x 0.56 in.
(24.9 x 47.3 x 14.3 mm)/R6014HS: 2.06 x

1.48 x 0.63 in. (52.3 x 37.5 x 16.0 mm)

• Weig ht : R 60 08HS : 0 .4 8 o z. (13. 5g )/
R6014HS: 0.72 oz. (20.8g)

(*1) Be sure that when using ESC's regulated

output the capacity of the ESC must meet
your usage condition.

Re-adjust the F/S position (only
for TM-8)

1

P res s and hol d the Li nk/ M od e swi t ch

between one(1) and two(2) seconds.

0 to 1 sec. 1 to 2 sec. More than 2 sec.

0 sec. 1 sec. 2 sec.

Press and Hold time

No function

With TM-8

(not included in this set)

To set the F/S

position(No re-link)

Re-link(ID set) and to

set the F/S position

No function

With TM-10, TM-14

(not included in this set)

Re-link(ID set)

FUTABA CORPORATION Phone: [phone] Facsimile: [phone]

Makuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan

1M23N17413 ©FUTABA CORPORATION 2009, 01 (1)

LED

Link/Mode Switch

R6008HS

R6014HS

LED

Link/Mode
Switch

Operation Mode Select

The operation mode is on " Normal mode" from
fa ct or y shi pp ing . Whe n to ch an ge th e mode,
please follow the steps shown below.

1

Turn off the receiver.

2

Press and hold the link/mode switch and

turn on the receiver. Keep the switch hold
more than one(1) second. The LED starts
flashing with the current status.

3

Release the switch.

4

Turn off the receiver.

By doin g th is ste p, the mode can swit ch over
between two(2) modes.

0 to 1 sec. More than 1 sec.

0 sec. 1 sec.

Press and Hold time

Turn on the receiver.

No function

Showing the CURRENT
mode with blink.

Red Blink = Normal
Green/Red Blink =

High Speed

Solid as the mode changed.

Red Solid = Normal
Green/Red Solid = High

Speed

(Become Red after one (1)
second)

（

Function

）

To change the mode between
Normal and High Speed

（

LED

Status

）

Plea se check the ope rat ion mode by o bse rvi ng
the LED when turning on the receiver. If possible
there's no FASST transmitter turned on around you

in order to make rmer check.

When turn on the receiver, the LED will be;

• Red when on "Normal mode"

• Green an d R ed (makes Orange) when on "High
Speed mode". (After two(2) seconds, change to Red.)

If there are s ome FASST t ran smitter turne d on
around the receiver, the LED may show the above
sta tus fo r a brief mome nt then chan ged to the
status indication as shown in the "LED indication"
table.

LED Indication

Green Red Status

Solid Solid Initializing

Off Solid No signal reception

Solid Off Receiving signals

Blink Off Receiving signals but ID is unmatched

Link to the transmitter

1

Press and hold the Link/Mode switch more

than two(2) seconds.

󾻯

WARNING

󾻭

Do not perform the linking procedure

with motor's main wire is connected
or the engine is operating as it may result in
serious injury.

󾻫

Wh ile the lin kin g is don e, ple a se

cycl e rec ei ve r power a nd chec k if
the receiver to be linked is really under the
control by the transmitter to be linked.

Th an k yo u f o r pu rcha si n g th e

R6 00 8 HS

,

R6014H S

FASST recei ver. These models have

two(2) operation mode as shown below.

Normal mode/High Speed mode

The "Normal mode" accepts any type of servos
or the peripherals as the frame rate of the output
is 14ms. The "High Spee d mode" only acce pt
the digita l ser vos for outputs from 1ch to 6ch,
in clu din g B LS seri es, and mos t pe rip her al

equipments such as the gyros or brushless ESCs.
The frame rate of the outputs is 7ms. The outputs
for other channels indicated below allow to use
any ty pe o f serv os a s the fram e rate of thes e
outputs are still 14ms on the High Speed mode.

R6008HS - 7ch and 8ch
R6014HS - 7ch to 12ch, DG1, DG2

The

R6008HS, R6014HS

are compatible with

the FASST transmitters as shown below.

MPDX-1 application(R6014HS
only)

Whe n to u se the

MPD X- 1

, pleas e prepa re the

exclusive short-plug shown below.

Short-plug
(sold separately)

Pl eas e in se rt the sho rt- p lu g t o

R6 0 1 4HS

's

"DATA" port.

Short-plug

CH11 and CH12 are valid to use of MPDX-1.
Other channels can not use the MPDX-1.

• When not to use the MPDX-1 , do not plu g the
short-plug to the "DATA" port.

• Please note that wh en the short-plug is plugged
to the "DATA" port, both CH11 and CH12 become
acceptabl e for MPDX-1. CH11 or CH12 ca n not
separately set as the "MPDX-1-ready-output."