Furuno PP-520 Operator's Manual

Download

Page 1

PRINTER

PP-520

OPERATOR'S MANUAL

www.furuno.com

Model

Page 2

Page 3

IMPORTANT NOTICES

General

• This manual has been authored with simplified grammar, to meet the needs of international users.

• The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury.

• Do not copy any part of this manual without written permission from FURUNO.

• If this manual is lost or worn, contact your dealer about replacement.

• The contents of this manual and equipment specifications can change without notice.

• The example screens (or illustrations) shown in this manual can be different from the screens you see on your display. The screens you see depend on your system configuration and equipment settings.

• Save this manual for future reference.

• Any modification of the equipment (including software) by persons not authorized by FURUNO will cancel the warranty.

• All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

How to discard this product

Discard this product according to local regulations for the disposal of industrial waste. For disposal in the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the correct method of disposal.

In the European Union

The crossed out wheeled bin lavel that can be found on your product indicates that this product should not be diposed of via the normal household waste stream. To prevent possible harm to the environment or human health please separate this product from other waste streams to ensure that it can be recycled in an environmentaly sound manner. For more details on available collection facilities please contact your local government office or the retailer where you purchased this product.

Page 4

SAFETY INSTRUCTIONS

WARNING

Indicates a condition that can cause death or serious injury if not avoided.

CAUTION

Indicates a condition that can cause minor or moderate injury if not avoided.

Mandatory Action

Prohibitive Action

Read these safety instructions before you operate the equipment.

Warning, Caution

WARNING

Do not cover the air vent of the equipment.

Covering the air vent may allow heat to build up inside the printer, which can cause fire.

Do not mount the equipment in an area exposed to oil, smoke, dust or water splash.

Fire or electrical shock can result.

Do not expose the equipment to an area subject to rain or water splash.

Fire or electrical shock can result.

Do not touch the printing head after printing.

Burn can result.

Follow the compass safe distances to prevent interference to a magnetic compass.

Do not disassemble or modify the equipment.

Fire, electrical shock or serious injury can result.

Immediately turn off the power at the equipment power switch if water or foreign object falls into the equipment.

Continued use of the equipment can cause fire, electrical shock or serious injury.

Only qualified personnel should work inside the equipment.

Fire, electrical shock can result by unsuitable modification.

Standard compass

1.00 m 0.60 m

Steering

compass

Page 5

iii

TABLE OF CONTENTS

FOREWORD................................................................................................................... iv

1. OPERATION ............................................................................................................. 1

1.1 Parts Name and Functions............................................................................................1

1.2 Keys and Lamps on the Control Panel..........................................................................1

1.3 Paper Operations ..........................................................................................................2

2. INSTALLATION ........................................................................................................3

2.1 Mounting Considerations...............................................................................................3

2.2 Mount the Printer...........................................................................................................4

2.3 Wiring ............................................................................................................................4

2.4 How to Set the Paper ....................................................................................................5

2.5 How to Set the Ink Ribbon Cartridge.............................................................................7

3. MAINTENANCE........................................................................................................8

3.1 Regular Maintenance ....................................................................................................8

3.2 Printer Status.................................................................................................................8

3.3 Self Test ........................................................................................................................9

SPECIFICATIONS ..................................................................................................... SP-1

OUTLINE DRAWING................................................................................................... D-1

Page 6

FOREWORD

A Word to the Owner of the PP-520

Congratulations on your choice of the FURUNO PP-520 Printer. We are confident you will see why the FURUNO name has become synonymous with quality and reliability.

Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers.

Your equipment is designed and constructed to meet the rigorous demands of the marine environment. However, no machine can perform its intended function unless properly installed and maintained. Please carefully read and follow the operation and maintenance procedures set forth in this manual.

We would appreciate feedback from you, the end-user, about whether we are achieving our purposes.

Thank you for considering and purchasing FURUNO equipment.

Features

The PP-520 prints navigation information fed from ship's radio communications system.

Configuration

• Print method 9-pin, serial, impact dot matrix

• Print speed Draft 200 cps (10 cpi)

• Ribbon life 3 million characters

• Paper size Roll paper 8.5-inch width

• Paper holder Paper near end sensor provided

• Source 24 VDC, over current/voltage protection circuit provided

Name Type Code No. Qty Remarks

Printer PP-520 1 Installation Materials CP16-05900 001-198-180-00 1 set Ink Ribbon Cartridge 7Q1VP80SF 001-198-190-10 1 Accessories FP05-04200 000-057-693-00 1 Roll paper

Page 7

1. OPERATION

1.1 Parts Name and Functions

1.2 Keys and Lamps on the Control Panel

The lamps on the control panel show printer status. The keys access the printer functions.

See section 3.2 for the printer status.

Power switch Turn the power on (|) or off (O). Printer cover Open to replace the ink ribbon cartridge; clear a paper jam. Keep the cover

closed otherwise. Control panel Control the printer functions (see the next section). Platen knob Eject the paper manually. Clear a paper jam. Do not touch in the Online mode. Release lever Release paper to straighten or remove it.

Printer cover

Control panel

Power switch

Platen knob

Release lever

Tear Off key and lamp (green)

Eject key

Paper Out lamp (orange)

Mode key

LF/FF key

On Line/Off Line key and lamp (green)

Page 8

1. OPERATION

1.3 Paper Operations

Changeover mode

Select a mode to operate the printer. Usually the printer is used in the Online mode.

Online mode operation (ST-BY)

Preview the printed characters at the Online mode.

Note: Do not cut the paper in the online mode; a paper jam may occur.

Offline mode operation

Note: After operation, press OnLine/OffLine key to return to online mode (ST-BY). You cannot

print in the offline mode.

Micro adjust mode operation (OnLine LED blinking)

Operation Procedure

Select OnLine/OffLine mode

Press the OnLine/OffLine key to go offline or online.

Micro adjust mode Press the OnLine/OffLine key approx. 3 seconds to go to the micro adjust

mode.

Operation Procedure

Preview 1) Press the Tear Off key to feed the paper over the printer cover to show the

characters printed.

2) Press the Tear Off key once more to feed the paper to previous state.

Operation Procedure

Paper feed 1) Press the LF/FF key to feed 1 line.

2) Press the LF/FF key for a while to feed the page.

Paper cutting 1) Press the Tear Off key to feed the paper to the cutting position.

2) Cut off the paper.

Eject paper 1) Press the Eject key to feed the paper in the reverse direction.

2) Replace the roll papaer by operation of the release lever.

Operation Procedure

Micro adjust the printing head

1) Each press of the Eject key feeds the paper by 0.118mm.

2) Each press of the LF/FF key feeds the paper back by -0.118mm.

3) Press the OnLine/OffLine key to return to the online mode and register the present location data.

Page 9

2. INSTALLATION

2.1 Mounting Considerations

General mounting considerations

• Select a location that is level and stable.

• The location should be well ventilated.

• Select a location that satisfies the operating environment stated in the specifications.

• Category of unit: Protected from the weather.

• Do not mount the printer on a table that is narrower than the bottom plate of the printer. This may tilt the printer, which can damage the printer mechanism and paper feeder.

• Leave sufficient space around the printer to allow for easy replacement of roll paper or ink ribbon cartridge.

• Refer to the outline drawing at the end of this manual for mounting dimensions.

Do not mount the printer where it may be exposed to the following:

• Direct sunlight

• Dusty place

• Water splash or spray

• Volatile solvent

• Near a heater or air conditioner

• Near a humidifier

• Radio noise from television set or radio receiver

• A place with static electricity

Page 10

2. INSTALLATION

2.2 Mount the Printer

Mount the printer on a tabletop with the fixtures supplied. Refer to the outline drawing at the end of this manual for the mounting dimensions.

1. Decide the location of the printer.

2. Set the ink ribbon cartridge and the roll paper to the printer. Refer to section 2.3 and 2.4

3. Set the fixtures (left/right) onto the printer. Fasten them with four self-tapping screws (φ5x20).

2.3 Wiring

Connect the power cable and the signal cable to the printer PP-520.

1. Connect the power cable 16S0084 to the printer.

2. Connect the cores of the power cable to the power source (24VDC) and ground terminal. (Red: +, Black: -, Shield: ground terminal)

3. Carry out the self test referring to section 3.3.

4. Attatch the EMI core supplied near the 36-pin plug of printer cable 57FE-17JE-BC10PL3000 and fix it with cable ties to fix the EMI core. (The cable tie is unnecessary if the larger printer cable is used.)

5. Connect the 36-pin plug to the signal connector of the printer.

6. Connect the 25-pin plug to the output port on the radiotelephone.

7. Power the radiotelephone and the printer. Print something to confirm correct printing.

405

200

Page 11

2. INSTALLATION

2.4 How to Set the Paper

A roll paper comes with the printer. Use only the roll paper (Type: A2 1PLYW, Code number: 000167-226-10)

Replace the roll paper

1. Get into the offline mode and cut off the paper.

2. Press the Eject key to eject the paper.

3. Turn the power off and remove the printer cover.

4. Remove the paper cover.

5. Lift the roll bar and take out the roll paper (and paper core).

6. Insert the roll bar into the new roll paper. Confirm the roll paper direction.

7. Lift up the paper near end bar and set the roll paper on the roll paper cradle.

8. Pull the release lever forward. Manually feed the paper over the paper guide bar and into the printer under the platen.

Paper

Paper cover

Ink ribbon cartridge

Printing head

Release lever

Fix (backward)

Release

(forward)

Paper near end bar

Roll paper

Roll bar

Roll paper cradle

Printing head

Paper guide

Platen

Paper cover

Page 12

2. INSTALLATION

9. Put the release lever in the backward position. Turn the platen knob clockwise to feed the paper so it reaches the paper guide bar.

10. Adjust the inclination of the paper if necessary. Pull the release lever forward to adjust the paper and then lock it. Move the guide ring (left/right) gently to hold the paper.

11. Remount the paper cover and the printer cover.

12. Turn the power on.

Paper guide bar

Platen

Platen knob

Guide ring

Release lever

Page 13

2. INSTALLATION

2.5 How to Set the Ink Ribbon Cartridge

Replace the cartridge when the ink runs out. (Type: 7Q1VP80SF, Code No.: 001-198-190-10)

1. Turn off the power and remove the printer cover.

2. Confirm that the printing head is at the center of the printing mechanism. Take out the ink ribbon cartridge.

3. Take out the new ribbon cartridge from its bag. Turn the ribbon feed knob in the direction of the arrow to remove slack in the ribbon.

4. Insert the ribbon between the ribbon mask and the printing head, and position the cartridge so that the hole under the ribbon feed knob is inserted into the shaft. Press the edge of the cartridge lightly to fasten it securely.

5. Manually move the printing head back and forth along the carriage bar to make sure the ribbon feed knob rotates in the direction of the arrow. Confirm that the ribbon moves freely. If the ribbon has slack, rotate the ribbon feed knob to remove the slack.

6. Replace the printer cover and turn on the power switch.

WARNING

The printing head is hot after printing. Do not touch it.

Burn can result.

Printing head

Printer cover

Ink ribbon

Ribbon cartridge

Ribbon feed knob

Page 14

3. MAINTENANCE

3.1 Regular Maintenance

• Confirm that the power terminal and ground terminal are securely fastened and clean. If a terminal is corroded, remove the corrosion with a wire brush.

• Remove dust from the printer with a clean, dry cloth. Remove dust from the air vent with a vacuum cleaner.

3.2 Printer Status

The panel lamps show the status of the printer. An error is referring to following table.

Other lamps

Status

On Line

(green)

Paper Out

(orange)

Remarks

Printing ST-BY On Off Paper near end On Blinking Replace roll paper. End of paper Off On Replace roll paper. Release lever opened Off – Push down the lever. Eject malfunction Off Blinking Confirm the paper feeder. Printing head hot Blinking – Do not touch the printing head. Adjust paper position Blinking – Other malfunctions Blinking Blinking Mode lamp blinking.

Tear Off lamp Both LEDs blink when the roll paper is on the paper cutting location. Mode lamp

The Mode 1 (default character mode) is selected and should not be changed

NOTICE

Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment.

Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors.

Page 15

3. MAINTENANCE

3.3 Self Test

Confirm that the ribbon cartridge and roll paper are correctly set then turn off the printer. Press the LF/FF key while turning on the power switch. After the self-test has begun, release the LF/FF key. The printer is normal if the print out shown below is printed. To stop the self test, turn off the power switch.

Draft

!” #$%&’ ()+,-.................................................................abcdefg

!” #$%&’ ()+,-.0..............................................................abcdefgh

” #$%&’ ()+,-.01............................................................abcdefghi

#$%&’ ()+,-.012............................................................abcdefghij

$%&’ ()+,-.0123..........................................................abcdefghijk

%&’ ()+,-.0123............................................................abcdefghijkl

&’ ()+,-.0123............................................................abcdefghijklm

’ ()+,-.0123............................................................abcdefghijklmn

Page 16

FURUNO

PP-520

SP - 1 E5080S02C

120906

SPECIFICATIONS OF PRINTER

PP-520

1 GENERAL

1.1 Printing system Serial impact dot matrix

1.2 Printing head 9 pins

1.3 Printing speed Draft: 200 characters/second

1.4 Type of paper 8.5-inch roll paper Width 208 to 216 mm Thickness 0.07 to 0.09 mm Maximum roll diameter 128 mm Inside diameter of core 25.4 mm (1 inch)

1.5 Paper advance Friction feed

1.6 Pitch of carriage return 4.23 mm (1/6-inch)

1.7 Data buffer 64 Kbyte

1.8 Ribbon Fabric ribbon cartridge (black)

1.9 Interface Parallel interface (centronics)

1.10 Control code IBM2380Plus Emulation, ESC/P mode

1.11 Noise Less than 59 dB

1.12 Protective function Reverse current, over-voltage/current protection

2 POWER SUPPLY

24 VDC: 1 A (25 W at continuous printing, 3.4 W at ST-BY)

3 ENVIRONMENTAL CONDITIONS

3.1 Ambient temperature 5°C to +35°C (storage: -25°C to +55° C)

3.2 Relative humidity 20% to 60% (no dew condensation)

3.3 Degree of protection IPX0

3.4 Vibration 0.25G, 10 to 55 Hz (storage: 0.50G, 10 to 55 Hz)

Page 17

D-1

Page 18

Page 19

Page 20

Page 21

FURUNO

PP-520

SP-1 J5080S02C

120906

プリンタ PP-520 仕様

１．総合

(1) 印字方式インパクトドットマトリクス (2) 印字ヘッド 9 ピン (3) 印字速度ドラフト 200 文字／秒 (4) 用紙 8.5 インチロール紙リア給紙、上質紙

紙幅 208～216 mm

紙厚 0.07～0.09 mm

ロール紙直径 128 mm 以下

コア内径 25.4 mm（1 インチ）

(5) 紙送りフリクションフィード (6) 改行ピッチ 4.23 mm（1/6 インチ） (7) データ・バッファ 64 キロバイト (8) インクリボンファブリックリボン（ブラック）カートリッジ (9) インターフェイスセントロニクスパラレル準拠 (10) コントロールコード IBM2380Plus エミュレーション、ESC/P モード (11) 騒音 59 dB 以下 (12) 保護機能逆接続保護、過電流・電圧保護

２．電源

DC24 V: 1 A（連続印字：約 25 W、待受時：約 3.4 W）

３．環境条件

(1) 使用温度範囲 5℃～＋35℃（保存温度：-25℃～＋55℃） (2) 相対湿度 20～60％（ただし結露なきこと） (3) 保護等級 IPX0 (4) 振動 0.25G、10～55 Hz（保存時：0.50G、10～55 Hz）

Page 22

3 章保守点検

3.3 セルフテスト

リボンカートリッジ、ロール紙のセットを確認し、電源が切れていることを確認します。

[LF/FF] キーを押しながら、電源を入れ、セルフテストが始まるのを確認して [LF/FF] キーを離します。次のようなセルフテスト印字がされれば正常です。セルフテストを終了するには電源

を切ります。