Furuno NAVnet 1753C, NAVnet 1733C, NAVnet 1723C, NAVnet 1763C, NAVnet 1722C Operator's Manual
...
MARINE RADAR
MODEL1722/1732/1742/1752/1762
MODEL1722C/1732C/1742C/1752C/1762C
MODEL1723C/1733C/1753C/1763C
Your Local Agent/DealerYour Local Agent/Dealer
9-52 Ashihara-cho,9-52 Ashihara-cho,
Nishinomiya, JapanNishinomiya, Japan
Telephone :Telephone : 0798-65-21110798-65-2111
faxfa
x
0798-65-42000798-65-4200
::
IRST EDITION :
IRST EDITION : APR.APR. 20012001
Printed in JapanPrinted in Japan
A
ll rights reserved.
A
ll rights reserved.
GG :: SEP.SEP. 26,200326,2003
PUB.No.PUB.No. OME-34940OME-34940
*00080918202**00080918202*
*00080918202**00080918202*
(( HIMAHIMA ))
MODEL1722/C SER.MODEL1722/C SER.
* 0 0 0 8 0 9 1 8 2 0 2 ** 0 0 0 8 0 9 1 8 2 0 2 *
*OME34940G00**OME34940G00*
*OME34940G00**OME34940G00*
* O M E 3 4 9 4 0 G 0 0 ** O M E 3 4 9 4 0 G 0 0 *
i
SAFETY INSTRUCTIONS
WARNING
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury can
result.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Keep heater away from equipment.
A heater can melt the equipment's power
cord, which can cause fire or electrical
shock.
Use the proper fuse.
Fuse rating is shown on the equipment.
Use of a wrong fuse can result in damage
to the equipment.
ELECTRICAL SHOCK HAZARD
Do not open the equipment.
Only qualified personnel
should work inside the
equipment.
CAUTION
A warning label is attached to the equipment. Do not remove the label. If the
label is missing or damaged, contact
a FURUNO agent or dealer about
replacement.
WARNING
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
Name: Warning Label (1)
Type: 86-003-1011-0
Code No.: 100-236-230
WARNING
Radio Frequency
Radiation Hazard
The radar antenna emits electromagnetic
radio frequency (RF) energy which can be
harmful, particularly to your eyes. Never
look directly into the antenna aperture from
a close distance while the radar is in
operation or expose yourself to the transmitting antenna at a close distance.
Distances at which RF radiation levels of
100 and 10 W/m
2
exist are given in the
table below.
Note: If the antenna unit is installed at a
close distance in front of the wheel house,
your administration may require halt of
transmission within a certain sector of
antenna revolution. This is possible - Ask
your FURUNO representative or dealer to
provide this feature.
MODEL
Distance to
100 W/m
2
point
Distance to
10 W/m
2
point
1722
1722C
1723C
Nil
Worst case
1.50 m
1732
1732C
1733C
1742
1742C
1762
1762C
1763C
0.60 m
0.40 m
Worst case
4.00 m
Nil
Worst case
1.00 m
Worst case
5.20 m
No one navigation device should ever be
solely replied upon for the navigation of
a vessel.
Always confirm position against all available
aids to navigation, for safety of vessel and
crew.
CAUTION
1752
1752C
1753C
0.15 m
Worst case
2.00 m
ii
TABLE OF CONTENTS
FOREWORD ...................................................................................................... viii
SYSTEM CONFIGURATIONS ..............................................................................x
WHAT IS WAAS? ................................................................................................ xii
1. OPERATIONAL OVERVIEW .........................................................................1-1
1.1 Operating Controls...................................................................................................... 1-2
1.1.1 Display unit controls......................................................................................... 1-2
1.1.2 Remote controller............................................................................................. 1-5
1.2 Inserting a Chart Card................................................................................................. 1-6
1.3 Turning the U nit On/Off................................................................................................ 1-7
1.4 Cursor Pad, Cursor......................................................................................................1-8
1.5 Display Brilliance, Panel Brilliance, Contrast, Hue....................................................... 1-9
1.5.1 Display brilliance, panel brilliance..................................................................... 1-9
1.5.2 Contrast.......................................................................................................... 1-10
1.5.3 Hue (MODEL1722C/1723C series)................................................................ 1-10
1.6 Selecting a Display.....................................................................................................1-11
1.6.1 Display modes.................................................................................................1-11
1.6.2 Selectin g a dis play.......................................................................................... 1-12
1.6.3 Switching control in combination and overlay screens.................................... 1-13
1.6.4 Selectin g ra dar so ur ce.................................................................................... 1-14
1.7 Data Boxes................................................................................................................ 1-15
1.7.1 Showing, hiding data boxes with soft key........................................................1-15
1.7.2 Rearra nging data box es................................................................................. 1-15
1.7.3 Temporari ly era si ng a dat a box....................................................................... 1-15
1.8 Function Keys............................................................................................................ 1-16
1.8.1 Executi ng a fun c tio n....................................................................................... 1-16
1.9 Simulation Display..................................................................................................... 1-17
2. RADAR OPERATION.....................................................................................2-1
2.1 Radar Display.............................................................................................................. 2-1
2.2 Tra nsm i ttin g, S tand-by................................................................................................. 2-2
2.3 T uni n g......................................................................................................................... 2-2
2.4 Adjusting the Gain....................................................................................................... 2-2
2.5 Reducing Sea Clutter................................................................................................... 2-4
2.5.1 How the A/C SEA works ................................................................................... 2-4
2.5.2 Adjus ting A/C SEA............................................................................................ 2-4
2.6 Reducing Precipitation Clutter ..................................................................................... 2-5
2.6.1 Adjus ting the A/C RAIN..................................................................................... 2-5
2.6.2 Adjusting the FTC............................................................................................. 2-6
2.7 Range Scale................................................................................................................ 2-7
2.8 Pulselength.................................................................................................................. 2-8
iii
2.9 Presentation Mode.......................................................................................................2-9
2.9.1 Selectin g a pr ese nt a ti on mode..........................................................................2-9
2.9.2 Descripti on o f pres entation modes..................................................................2-10
2.10 Measuring the Range...............................................................................................2-12
2.10.1 Measuring range by range rings....................................................................2-12
2.10.2 Measuring range by cursor............................................................................2-13
2.10.3 Measuring range by VRM.............................................................................2-14
2.10.4 Erasing a VRM, VRM indication....................................................................2-15
2.10.5 Erasing EBL/VRM data boxes.......................................................................2-15
2.10.6 Hiding EBL/VRM data boxes.........................................................................2-15
2.10.7 Moving EBL/VRM data boxes.......................................................................2-15
2.11 Measuring the Bearing.............................................................................................2-15
2.11.1 Measuring bearing by cursor.........................................................................2-15
2.11.2 Measuring bearing by EBL............................................................................2-15
2.11.3 Erasin g an EB L, EBL indicati on.....................................................................2-16
2.11.4 Erasin g EB L/VRM data boxes.......................................................................2-16
2.11.5 Hiding EBL/VRM data boxes.........................................................................2-16
2.11.6 Moving EBL/VRM data boxes........................................................................2-16
2.12 Erasing the Heading Line, North Marker ..................................................................2-17
2.13 Reducing Noise........................................................................................................2-17
2.14 Reducing Radar Interference...................................................................................2-18
2.15 Zoom........................................................................................................................2-19
2.15.1 Zooming in on radar targets..........................................................................2-19
2.15.2 Zooming ARP, TTM targets...........................................................................2-19
2.16 Shifting the Picture...................................................................................................2-20
2.16.1 Manual shift..................................................................................................2-20
2.16.2 Automa tic shift...............................................................................................2-21
2.17 Using the Offset EBL................................................................................................2-22
2.17.1 Predicting a collision course..........................................................................2-22
2.17.2 Measuri n g ra n ge & be ar i ng be twe en tw o targets...........................................2-23
2.18 Echo T r ai ls...............................................................................................................2-24
2.18.1 Trail time.......................................................................................................2-24
2.18.2 S t ar ti n g ech o trails........................................................................................2-25
2.18.3 Trail brilliance (MODEL1722 series)..............................................................2 -25
2.18.4 Trail gradation (MODEL1722C/1723C series)...............................................2-25
2.18.5 Trail color (MODEL1722C/1723C series)......................................................2-26
2.19 Echo S tretch.............................................................................................................2-27
2.20 Echo A veraging........................................................................................................2-28
2.21 Outputting TLL Data.................................................................................................2-29
2.22 Guard Alarm.............................................................................................................2-30
2.22.1 Setting a gu ar d al ar m z one...........................................................................2-30
2.22.2 When the al ar m is viol ate d…........................................................................2-31
2.22.3 Canceling the guard alarm............................................................................2-31
2.23 Watchma n................................................................................................................2-32
2.23.1 How watchman works...................................................................................2-32
2.23.2 Turning on/o ff watchman...............................................................................2-32
2.23.3 Setting watchman stand-by interval...............................................................2-32
2.24 Waypoi nt Marker......................................................................................................2-33
i
v
2.25 ARP (option), TTM operation................................................................................... 2-34
2.25.1 Activ ating/de activating ARP, TTM ................................................................. 2-35
2.25.2 Acquiring and tracking targets (ARP only)..................................................... 2-36
2.25.3 Displaying target number (internal, external ARP) ........................................ 2-37
2.25.4 Terminating tracking of ARP targets.............................................................. 2-38
2.25.5 Setting vector attributes (ARP)..................................................................... 2-39
2.25.6 Displaying past position display (ARP) ......................................................... 2-40
2.25.7 AR P, TTM target dat a ....................................................................................2-41
2.25.8 CPA/TCPA alarm (ARP)................................................................................ 2-42
2.25.9 Lost target alarm (ARP)................................................................................ 2-43
2.26 Interpreting the Radar Display................................................................................. 2-44
2.26.1 General ........................................................................................................ 2-44
2.26.2 False echoes ................................................................................................ 2-46
2.26.3 SART (Search and Rescue Transponder)..................................................... 2-48
2.26.4 Racon (Radar Beacon)................................................................................. 2-50
3. PLOTTER OPERA TION.................................................................................3-1
3.1 Plotter Displays............................................................................................................3-1
3.1.1 Full-screen plotter display................................................................................. 3-1
3.1.2 Compass display.............................................................................................. 3-3
3.1.3 Highway display............................................................................................... 3-5
3.1.4 Nav data display............................................................................................... 3-6
3.2 Presentation Mode....................................................................................................... 3-7
3.2.1 North-up........................................................................................................... 3-7
3.2.2 Course-up ........................................................................................................ 3-8
3.2.3 Auto course-up................................................................................................. 3-8
3.3 Shifting the Display ...................................................................................................... 3-9
3.4 Chart Scale.................................................................................................................. 3-9
3.5 Chart Cards............................................................................................................... 3-10
3.5.1 Chart card overview........................................................................................ 3-10
3.5.2 Indices and chart enlargement.........................................................................3-11
3.5.3 FURUNO and NavCharts™............................................................................ 3-12
3.5.4 C-MAP cards.................................................................................................. 3-14
3.6 Working with Track .................................................................................................... 3-18
3.6.1 Displaying track .............................................................................................. 3-18
3.6.2 Stopping, restating plotting of own ship track.................................................. 3-19
3.6.3 Changi ng tr ack col or (MODEL1722C / 17 2 3C ser i es)....................................... 3-20
3.6.4 Track plotting method and interval for own ship track..................................... 3-21
3.6.5 Changing own ship track/mark distribution setting.......................................... 3-22
3.6.6 Erasing tr ack.................................................................................................. 3-23
3.7 Marks, Lines.............................................................................................................. 3-25
3.7.1 Entering a mark .............................................................................................. 3-25
3.7.2 Changing mark attributes................................................................................ 3-25
3.7.3 Selecting line type.......................................................................................... 3-26
3.7.4 Erasing marks, lines....................................................................................... 3-27
3.8 Wayp oints.................................................................................................................. 3-29
3.8.1 Enterin g way p oints......................................................................................... 3-29
3.8.2 Editing waypoint data..................................................................................... 3-32
v
3.8.3 Erasing w ayp oints...........................................................................................3-34
3.8.4 Changing waypoint mark size (FURUNO, NavCharts™).................................3-35
3.8.5 Searchi ng w ayp oi nt s.......................................................................................3-36
3.9 Routes.......................................................................................................................3-37
3.9.1 Creating routes...............................................................................................3-37
3.9.2 Connecting routes...........................................................................................3-41
3.9.3 Inserting waypoints.........................................................................................3-42
3.9.4 Removing waypoints from a route...................................................................3-44
3.9.5 Erasing r out es.................................................................................................3-44
3.10 Navigation................................................................................................................3-45
3.10.1 Navigating to a "quick point"..........................................................................3-45
3.10.2 Navigating to waypoints................................................................................3-46
3.10.3 Navigating to ports, port services (NavCharts™ C-MAP) ..............................3-47
3.10.4 Following a route...........................................................................................3-49
3.1 1 Alarm s ....................................................................................................................3-53
3.11.1 Audio alarm on/off.........................................................................................3-53
3.1 1.2 Arri val alarm..................................................................................................3-54
3.1 1.3 Anch or watch alarm.......................................................................................3-55
3.11.4 XTE (Cross Track Error) alar m......................................................................3-56
3.11.5 S p ee d alar m..................................................................................................3-56
3.11.6 Proximi ty alar m.............................................................................................3-57
3.11.7 T r ip al arm......................................................................................................3-58
3.1 1.8 Al arm information..........................................................................................3-59
3.12 Resetting Trip Distance............................................................................................3-60
3.13 Entering the MOB Mark, Setting MOB as Destination ..............................................3-61
4. VIDEO SOUNDER OPERATION ...................................................................4-1
4.1 Principle o f Oper atio n...................................................................................................4-1
4.2 Sounder Displays.........................................................................................................4-2
4.2.1 Selectin g a sou nd er dis play..............................................................................4-2
4.2.2 Descripti on o f soun der displ a ys........................................................................4-3
4.2.3 Selecting screen split method in combination displays......................................4-7
4.3 Automatic Sounder Operation......................................................................................4-8
4.3.1 How the automatic sounder works....................................................................4-8
4.3.2 Types of automa ti c soun d er modes...................................................................4-8
4.3.3 How to enable automatic sounder operation.....................................................4-8
4.4 Manual Sounder Operation..........................................................................................4-9
4.4.1 Selecting the manual mode...............................................................................4-9
4.4.2 Selectin g di spla y ra ng e.....................................................................................4-9
4.4.3 Adjus ting the gain..............................................................................................4-9
4.4.4 Range shifting.................................................................................................4-10
4.5 Measuring Depth, Time.............................................................................................. 4-11
4.6 Reducing Interference................................................................................................4-12
4.7 Reducing Low L evel Noi se.........................................................................................4-13
4.8 Erasing Weak Echoes ..............................................................................................4-14
4.9 White Marker (MODEL1722C/1723C series)..............................................................4-15
vi
4.10 Picture Advance Spee d............................................................................................4-16
4.10.1 Advancement independent of ship’s speed................................................... 4-16
4.10.2 Advancement synchronized with ship’s speed.............................................. 4-17
4.11 Display Colors (MODEL1722C/1723C series).......................................................... 4-18
4.12 Alarms.....................................................................................................................4-19
4.12.1 Au di o al arm on/ o ff......................................................................................... 4-19
4.12.2 Bottom alarm ................................................................................................ 4-20
4.12.3 Fish alarm..................................................................................................... 4-20
4.12.4 Fish alarm (B/L)............................................................................................ 4-21
4.12.5 Water temperature alarm.............................................................................. 4-22
4.12.6 When an alarm setting is violated................................................................. 4-23
4.13 Water Temperatur e Graph....................................................................................... 4-24
4.14 Changing Pulse Repetition Rate .............................................................................. 4-24
4.15 Interpreting the Sounder Display.............................................................................. 4-25
4.15.1 Zero line....................................................................................................... 4-25
4.15.2 Bottom echo................................................................................................. 4-25
4.15.3 Fish school echoes....................................................................................... 4-26
4.15.4 Surface noise/Aeration................................................................................. 4-26
5. CUSTOMIZING YOUR UNIT..........................................................................5-1
5.1 Generic Setup..............................................................................................................5-1
5.2 Radar Setup................................................................................................................ 5-3
5.2.1 Radar display setup.......................................................................................... 5-3
5.2.2 Radar range setup............................................................................................ 5-6
5.2.3 Function key setup ........................................................................................... 5-7
5.3 Plotter Setup................................................................................................................ 5-9
5.3.1 Navigation options............................................................................................ 5-9
5.3.2 Function key setup ......................................................................................... 5-10
5.4 Chart Setup............................................................................................................... 5-12
5.4.1 Chart offset..................................................................................................... 5-12
5.4.2 FURUNO, Nav-Charts™ chart attributes........................................................ 5-13
5.4.3 C-MAP chart attributes................................................................................... 5-16
5.5 Data Boxes Setup...................................................................................................... 5-20
5.6 Hot Page Setup......................................................................................................... 5-21
5.7 Navigator Setup......................................................................................................... 5-23
5.7.1 Navigation data source................................................................................... 5-23
5.7.2 GPS receiver setup (Set equipped with GP-310B/320B)................................ 5-24
5.7.3 TD displ ay setu p............................................................................................. 5-27
5.8 Nav Data Display Setup............................................................................................. 5-29
5.9 Sounder Setup........................................................................................................... 5-30
5.9.1 System setu p.................................................................................................. 5-30
5.9.2 Sensor set up.................................................................................................. 5-32
5.9.3 Sounding range, zoom range, bottom lock range............................................ 5-33
5.9.4 Function key setup ......................................................................................... 5-34
vii
6. DATA TRANSFER..........................................................................................6-1
6.1 Memory Card Operations.............................................................................................6-1
6.1.1 Formatting memory cards.................................................................................6-1
6.1.2 Saving dat a to a mem ory car d..........................................................................6-2
6.1.3 Playing back data from a mem or y car d.............................................................6-4
6.2 Uploading, Downloading Data......................................................................................6-5
6.2.1 Setting communication software on the PC.......................................................6-5
6.2.2 Uploading or downloading data.........................................................................6-5
6.3 Loading W a yp oint Data from Yeoman..........................................................................6-8
6.4 Receiving Data Via Network Equipment.......................................................................6-9
6.5 Outputting Data Through the Network........................................................................6-10
7. MAINTENANCE, TROUBLESHOOTING ......................................................7-1
7.1 Preventive Maintenance...............................................................................................7-1
7.2 Replacement of Fuse...................................................................................................7-2
7.3 Replacement of Battery................................................................................................7-2
7.4 Simple Troubleshooting................................................................................................7-3
7.4.1 Gener al.............................................................................................................7-3
7.4.2 Radar................................................................................................................7-4
7.4.3 Plotter...............................................................................................................7-5
7.4.4 Sounder............................................................................................................7-6
7.5 Diagnostics..................................................................................................................7-7
7.5.1 Memory I/O test................................................................................................7-7
7.5.2 Test pattern.....................................................................................................7-10
7.5.3 Keyboard, remote controller test.....................................................................7-11
7.6 GPS Status Display....................................................................................................7-12
7.7 Clearing Memories.....................................................................................................7-13
7.8 Error Messages..........................................................................................................7-14
APPENDIX ......................................................................................................AP-1
Menu Overview ............................................................................................................... AP-1
Geodetic Chart List....................................................................................................... AP-12
World Time Chart.......................................................................................................... AP-13
Icons.............................................................................................................................AP-14
SPECIFICATIONS........................................................................................... SP-1
INDEX..........................................................................................................Index-1
Declaration of Comformity
viii
FOREWORD
A Word to the Owner of the MODEL1722/1722C/1723C
Series Marine Radar
FURUNO Electric Company thanks y ou for purchasing the
MODEL1722/1722C/172 3C S er ies Mari ne Radar. We are confident you will
discover why the FURUNO nam e has become synonymous with quality and
reliability.
For over 50 year s FURUNO Elec tric Company has enjoyed an en vi able
reputation for quality and reliability throughout the world. This dedic ation to
excellence is furthered by our extensiv e global network of agent s and dealers.
Your radar is designed and constructed t o m eet the rigor ous demands of the
marine envir onment. However, no machine can perform its intended function
unless proper ly installed and maintained. Pl eas e c ar efully read and f ollow the
operation and m aintenance pr oc edures set forth in this manual.
We would appreciate feedback from you, the end-user, about whether we are
achieving our purposes.
Thank y ou for consideri ng and pur c hasing FUR UNO.
FOREWORD
ix
Features
The MODEL1722/1722C/1723C series work within our ne w product - network
system called the “NavNet.” Each product has an IP address to communicate
with NavNet compatible products within the network, using TCP/IP protocol
through an Ethernet 10 Base-T network.
The main features are
! Bright 7” screen visible even under direct sunlight.
MODEL1722 series: Monochrome LCD
MODEL1722C series: Color LCD
MODEL1723C series: High-precision color LCD
! User friendly operation with combination of discrete keys, soft keys and cursor pad.
! Accepts FURUNO and Nav-charts™ (NAVIONICS) or C-MAP NT/NT+ charts (C-MAP).
All names mentioned are registered trademarks of their respective companies.
! Fast chart redraw.
! Built-in NavNet interface circuit board.
! 12-channel GPS Receiver GP -310B with highly accurate position fixing optionall y
available or GP-320B with WAAS (see the note in below.)
! User programmable function keys.
! Video sounder picture available with connection to optional network sounder.
! ARP function (when connecting with MODEL1833/ 1833C series)
x
SYSTEM CONFIGURATIONS
All NavNet products incorporate a “network circuit board” to integrate each
NavNet product on board through an optional LAN cable (Ethernet 10BASE-T).
Each NavNet product is assigned an IP address to enable transfer of images
between other NavNet products. For example, video plotter pictures can be
transferred to a radar and vice versa. Pictures received via the NavN et may be
adjusted at the receiving end.
The number of display units which may be installed depends on the number of
network sounder connected. For a system incorporating three or more products,
a “hub” is required to process data.
For one network sounder: one radar and three plotters
For two network sounder: one radar and two plotters
NavNet system
Antenna Unit
(ex. MODEL 1722/1722C/1723C)
Network sounder
ETR-6/10N
ETR-30N
Heading
sensor
External buzzer
PC
Echo sounder
E/S
Navigator
GPS receiver
GP-310B/320B
12-24 VDC
Other NavNet unit
(GD-1700 etc.)
Rectifier*
PR-62
RU-3423
100/110/115/220/230 V AC
1φ, 50/60 Hz
*PR-62: MODEL1722/1722C/1732/1732C/1723C/1733C
RU-3423: MODEL1742/1742C/1752/1752C/1762/1762C/1753C/1763C
Display Unit
RDP-130 (monochrome)
RDP-131 (color, QVGA)
RDP-143 (color, VGA)
Remote
Controller
RMC-100
NavNet system
SYSTEM CONFIGURATIONS
xi
Two-unit NavNet system
Antenna Unit
GP-310B/320B
Radar data
Plotter data
Two-unit NavNet system
Three-or more unit NavNet system (Max. 4 NavNet cap able displ ay units)
Antenna Unit
GP-310B/320B
HUB
Radar data
Plotter data
Network Sounder
ETR-6/10N
ETR-30N
(option)
Sounder data
Note: The picture disappears
10 seconds after the NavNet
cable is disconnected from a
"sub" NavNet display unit.
Network Sounder
ETR-6/10N
ETR-30N
(option)
Three-or more unit NavNet system
xii
WHAT IS WAAS?
WAAS, available in North America, is a provider in the worldwide SBAS (Satellite
Based Augmentati on System) navigation system. SBAS provides GPS signal
corrections to SBAS users, for even better position accuracy, typically better
than three meters. Two more SBAS providers are al so current ly under
development, MSAS (Multi-Funct ional Satellite Augment at ion System) for Japan
and EGNOS (Euro Geostationary Navigation Overl ay Service) for E ur ope. A ll
provides will be compatible with one anot her, thus provi ding “seamless” positi on
fixes to SBAS users.
150°W 120°W 90°W 60°W 30°W 0 30°E 60°E 90°E 120°E 150°E
150°W 120°W 90°W 60°W 30°W 0 30°E 60°E 90°E 120°E 150°E
0
20°S
40
°
S
60
°
S
20
°
N
40
°
N
60
°
N
0
20
°
S
40
°
S
60
°
S
20
°
N
40
°
N
60
°
N
WAAS
EGNOS
MSAS
Satellite, Region Position
120, AOR-E
15.5°W
122, AOR-W
54°W
131, IOR
64.5°E
134, POR
178°E
131
134
122
120
Initial operation time
WAAS: 2003
EGNOS: 2004
MSAS: 2005
At the time of thi s sof tware release, SBAS is still under d evelopment (Providers
are expected t o have initi al operations capability from the times shown above.)
During this developmental period, which may l ast for several years, there is no
guarantee of the accuracy, integrity, continuity, or availabili ty of the SBAS signal.
Furuno will accept no respo ns ibility for the use of the signal for other than the
above stated purpose. It is the user’s respons ibility to exercise common
prudence and navigational judgment whil e using the SBAS signal.
Note: This manual uses “WAAS” when referring to any SBAS provider.
1-1
1. OPERATIONAL OVERVIEW
This chapter provides basic information needed to get you started using your
radar. The follow topics are presented:
• Control overview
• Chart card insertion
• Power on/off
• Contrast, brilliance and hue (Color series only) adjustments
• Display selection
• Data boxes
• Function keys
• Simulation display
NOTICE
NOTICE
The brilliance of the LCD is adjustable
to match a wide variety of lighting
conditions. However, its maximum
setting may not be sufficiently bright
to permit viewing of the display with
polarized sunglasses.
Note: The example screens shown in this manual may not match the screens
you see on your display. The screen you see depends on your system
configuration and equipment settings.
1. OPERATIONAL OVERVIEW
1-2
1.1 Operating Controls
1.1.1 Display unit controls
Overview of display un it controls
The radar systems are mainly operated with controls of the display unit (and
remote controller). Ten keys are labeled and they provide the function shown on
their labels. The five soft keys provide various functions according to current
operating mode. The [ENTER] knob mainly functions to register selections on
the menu and enter alphanumeric data. The cursor pad’s main function is to
move the cursor across the screen. Whenever you operate a key, a single beep
confirms operation. Invalid operation causes the unit to emit three beeps.
Cursor pad
Selects menu items and options;
shifts cursor. Press, release and
press again to change setting
consecutively.
Selects display mode.
Soft keys
Momentary press:
Registers own ship’s
position as a waypoint.
Press three seconds:
Marks man overboard
position.
Opens/closes the main menu.
Displays the soft keys for EBL/VRM.
Radar: Displays the soft keys for adjustment of
gain, A/C SEA, A/C RAIN and FTC.
Sounder: Adjusts gain.
Long press: Turns power on/off.
Momentary press: Opens the
display for adjustment of brilliance,
etc. For radar, switches STBY and TX.
ENTER knob
Push: Registers options on menus.
Rotate: Selects character; adjusts sensitivity
(sounder, radar); chooses menu items and options.
Clears data; erases selected mark.
Opens/closes the alarm menu.
Shows or hides the soft
keys, function keys,
nav data alternately.
Chart slot
Selects a range.
Control p anel
1. OPERATIONAL OVERVIEW
1-3
Soft keys
The five soft keys’ functions change according to the operation. Their labels for
their current functions are shown on the screen to the left of the keys. To hide or
show the soft key labels, press the [HIDE/SHOW] key. Each press of the key
shows preset soft keys, user function keys or turns off navigation information (at
the top of the screen).
SOFT
KEYS
Display unit
Some soft keys show the current state of the soft key function in reverse video
as shown below.
.250/ 319.9
°
M
.125nm
SP
H-UP
SIGNAL
PROCESS
+
359.9°R
0.24nm
RETURN
E. AVG*
OFF
I. REJ
LOW
PULSE
SHORT
E. STR
LOW
Current option
shown in reverse
video
*: Only when MODEL 1833/C series are
used as radar source.
Plotter display
1. OPERATIONAL OVERVIEW
1-4
[ENTER] knob
The [ENTER] knob functions to
• Register data
• Enter alphanumeric data such as waypoint name
• Select menu items and options
• Adjust setting
Clockwise rotation of the knob selects an alphabet, symbol or numeric, in one of
the sequences shown below. After you have selected desired alphanumeric
character push the [ENTER] knob to register your selection.
[ENTER] knob
ENTER knob
Alphabet, sy mbol, numeric
A ! B ! C ! D ! E ! F ! G ! H ! I ! J ! K ! L ! M ! N ! O ! P ! Q !
R ! S ! T ! U ! V ! W ! X ! Y ! Z ! & ! _ ! ’ ! # ! 0 ! 1 ! 2 ! 3 !
4 ! 5 ! 6 ! 7 ! 8 ! 9
Numerics
0 ! 1 ! 2 ! 3 ! 4 ! 5 ! 6 ! 7 ! 8 ! 9
1. OPERATIONAL OVERVIEW
1-5
1.1.2 Remote controller
SAVE
RANGE
DISP
MOB
ABC1DEF2GHI
MNO
4
JKL
STU
7
VWX
65
98
YZ&
PQR
0
GAIN
’#
EBL / VRM
ENT
WPT
MARK
ENT
CNTL
CENTER
ALARM
SK3SK1 SK2
HIDE /SHOW
SK4 SK5
TX /STBY
BRILL
CLEAR
TONE
MENU
ACQ
3
Operating distance
90°: Up to 5 m
±45°: Up to 3 m
Replace the batteries (AA) when the
distance from which the display
unit can be operated shortens.
Note: The remote controller may
become damaged if dropped.
Mishandling of the remote
controller is not covered by
the warranty.
Remote controller
Key Function Key Function
RANGE
Same as RANGE key on
display unit.
CLEAR
Same as CLEAR key on
display unit.
DISP
Same as DISP key on
display unit.
MENU
Same as MENU key on
display unit.
SAVE MOB
Same as SAVE MOB key on
display unit.
BRILL Adjusts display brilliance.
Ten keys Enter alphanumerics. TONE Adjusts display contrast.
EBL/VRM
Same as EBL/VRM key on
display unit.
TX/STBY
Toggles radar between
standby and transmit.
GAIN
Same as GAIN key on
display unit.
ACQ
Acquires radar target.
(Requires radar source
equipped with ARP.)
WPT
Displays “alphabet” WPT list
on plotter display.
ALARM
Same as ALARM key on the
display unit.
MARK ENT
Same as MARK ENTRY soft
key.
HIDE/SHOW
Same as HIDE/SHOW key
on display unit.
CENTER
Returns own ship to screen
center on plotter display.
SK1 – SK5
(soft keys)
Same as soft keys on
display unit.
CNTL
Switches control between
displays on combination
displays.
ENT
Same as ENTER knob on
display unit.
1. OPERATIONAL OVERVIEW
1-6
1.2 Inserting a Chart Card
Your unit reads FURUNO and Nav-Charts™ (NAVIONICS), or C-MAP chart
cards, depending on its specifications. Insert the appropriate chart card for your
area as follows:
1. Open the chart card slot lid.
Chart slot
Display unit
2. Insert desired chart card groove side up.
3. Close the lid to protect the chart drive.
Note 1: Do not insert or remove the chart card while turning power on. This may
cause the equipment to freeze.
Note 2: Do not remove a card while the chart is being drawn. This may cause
the equipment to freeze.
Note 3: A card remover is supplied to ease removal of chart cards. Attach the
card remover to the right-hand side hole on the card and pull to remove
card. You can leave the card remover attached to the card while the
card is in the card slot - push the card remover leftward until it contacts
the recessed area in the card.
Note 4: For multiple display units, do not use the same chart card type in more
than one display unit.
Chart card and card remover
1. OPERATIONAL OVERVIEW
1-7
1.3 Turning the Unit On/Off
Press the [POWER/BRILL] key to turn the unit on. A beep sounds and the
equipment proceeds in the sequence shown below, displaying the product
information screen, startup test results and the chart usage disclaimer, in that
order. The startup test checks the ROM, RAM, internal battery and backup data
for proper operation, displaying the results for each as OK or NG (No Good). If
NG appears, an appropriate message appears on the screen. For any NG, try to
press any key to go to the chart disclaimer screen, then perform the diagnostic
test referring to the paragraph “7.5 Diagnostics.”
RADAR PLOTTER
STATION NAME:
RADAR
FURUNO ELECTRIC CO., LTD.
CHARTS AVAILABLE
FLYBRDG = ANB01004
RADAR = ANB01003
STARTUP TEST
ROM OK
RAM OK
BACKUP DATA OK
INTERNAL BATTERY OK
NO NATIONAL HYDROGRAPHIC
OFFICE HAS VERIFIED THE
INFORMATION IN THIS
COASTLINE DATA CARD AND NONE
ACCEPT LIABILITY FOR THE
ACCURACY OF REPRODUCTION OR
ANY MODIFICATIONS MADE
THEREAFTER. THIS PRODUCT WITH
THIS COASTLINE DATA CARD
DOES NOT REPLACE THE
REQUIREMENT TO USE THE
APPROPRIATE PRODUCTS FOR
NAVIGATION ACCORDING TO
NATIONAL AND INTERNATIONAL
REGULATIONS.
è
è
Product information Startup test Chart disclaimer
PROGRAM No. 03591730**
Host Name
Chart List
** = Program version no.
(Two program version numbers.
One for NAVIO and one for C-MAP.)
The magnetron in the antenna unit takes about one minutes and thirty seconds
to warm up before the radar can be operated. The time remaining for warm up of
the magnetron appears at the center of the display, counting down from 1:30 to
0:01.
You may press any key at the chart disclaimer screen to show the last-used
display, or wait several seconds to let the equipment do it for you.
To turn the unit off, press and hold down the [POWER/BRILL] key until the
screen goes dark (approx. 3 sec.). To protect the LCD attach the hard cover.
Note that the network sounder will be turned off approx. three minutes after
turning off the power.
Note: You are asked if you want to start the simulation mode, which provides
simulated operation of the equipment, the first time you turn on the power
(or any time power is applied after a memory reset) the message shown
below is displayed. Push the [ENTER] knob to start the simulation mode,
or press the [CLEAR] key to start normal operation. For further details
about the simulation mode, see the paragraph “1.9 Simulation Display.”
START
SIMULATION MODE?
YES ... PUSH ENTER KNOB
NO ... PUSH CLEAR KEY
TO SKIP.
1. OPERATIONAL OVERVIEW
1-8
1.4 Cursor Pad, Cursor
The cursor pad mainly functions to shift the cursor, for measurement of range
and bearing to a location (radar) and latitude and longitude position (plotter).
Operate the cursor pad to shift the cursor. The cursor moves in the direction of
the arrow or diagonal pressed, on the cursor pad.
For the plotter display, the cursor can be turned off with the CENTER soft key.
This also returns own ship marker to the screen center.
34° 22. 3456'N 272.4°M TRIP NU
080° 22. 3456'E
15.9 nm 99.9 nm
GOTO
CURSOR
MODE
NTH UP
CENTER
MARK
ENTRY
+
Cursor data
L/L position,
Range and
bearing from
own ship to
cursor
Cursor
16.0nm
D. BOX
ON/ OFF
Cursor
Radar display
Plotter display
.250/ 319.9
°
M
.125nm
SP
H-UP
+
359.9°R
0.24nm
RADAR
DISPLY
NAV
FUNC
ZOOM &
D. BOX
SIGNAL
PROC
TARGET
Cursor, cursor data
1. OPERATIONAL OVERVIEW
1-9
1.5 Display Brilliance, Panel Brilliance, Contrast,
Hue
You can adjust display brilliance, panel brilliance, contrast and hue
(MODEL1722C/1723C series only) as shown below.
1.5.1 Display brillianc e, panel brilli an ce
1. Press the [POWER/BRILL] key momentarily. A set of soft keys for
adjustment of brilliance, contrast and hue (MODEL1722C/1723C series only)
appear. The last-used adjustment window appears. In the example below the
display brilliance adjustment window is shown.
.250/ 319.9
°
M
.125nm
SP
H-UP
.250/ 319.9
°
M
.125nm
SP
H-UP
MODEL1722C/1723C series MODEL1722 series
PANEL
BRILL
CONTST
/HUE
RETURN
DISPLAY BRILLIANCE
8
PANEL
BRILL
CONTST
BRILL
CONTST
RETURN
DISPLAY BRILLIANCE
8
Current selection is higtlighted.
DISPLY
BRILL
DISPLY
BRILL
RADAR
STBY
RADAR
STBY
BRILL
CONTST
Brilliance adjustment s oft keys
2. Press the DISPLY BRILL or PANEL BRILL soft key as appropriate. An
adjustment window appears at the bottom of the screen. This window shows
the name of the item selected for adjustment plus current brilliance level, by
bar graph.
DISPLAY BRILLIANCE
8
PANEL BRILLIANCE
8
Display brilliance Panel brilliance
Display brilliance and panel brilliance window s
3. Adjust the [ENTER] knob, clockwise to raise the setting or counterclockwise
to decrease it. You may also use the soft key pressed at step 2, in which
case the item selected is adjusted cyclically, from low to high. Eight levels of
display brilliance and panel brilliance are available.
4. Hit the RETURN soft key to finish.
The display brilliance can be adjusted by pressing the [POWER/BRILL] key.
If the unit is turned on with minimum display brilliance, press the
[POWER/BRILL] key consecutively to adjust the brilliance.
1. OPERATIONAL OVERVIEW
1-10
1.5.2 Contrast
1. Press the [POWER/BRILL] key momentarily.
2. Press the CONTST (monochrome) or CONTST/HUE (color) soft key.
3. For MODEL 1722C/1723C series, two soft keys appear at the pressing of the
CONTST/HUE soft key: CONTST and HUE. Press the CONTST soft key to
adjust the contrast.
CONTRAST
8
Contrast window
4. Adjust the [ENTER] knob, clockwise to raise the setting or counterclockwise
to decrease it. You may also use the CONTST soft key, in which case the
item selected is adjusted cyclically, from low to high. 16 levels (monochrome)
and 10 levels (color) of contrast are available.
5. Press the RETURN soft key to finish.
1.5.3 Hue (MODEL 17 22C/ 17 23C ser i es )
1. Press the [POWER/BRILL] key momentary.
2. Press the CONTST/HUE (MODEL1722C series) or HUE (MODEL1723C
series) soft key.
3. Press the HUE soft key to show the hue setting window.
HUE
▲
¡
DAY
¡
NIGHT
¡
TWILIGHT
¤
MANUAL SET
▼
Hue window
4. Operate the cursor pad or [ENTER] knob to select hue desired, referring to
the table below. MANUAL SET follows the color settings on the RADAR
DISPLAY SETUP for the radar, CHART DETAILS menu for the plotter and
SOUNDER MENU for the sounder.
Day Night Twilight Applicable mode
Characters Black Red Green Plotter, radar, sounder
Radar ring Green* Red Green* Radar
Radar echo Red Orange Yellow Radar
Background White Black Blue Plotter, radar
Landmass Yellow Light Yellow Dim Yellow Radar
*: Red on C-map
5. Hit the RETURN soft key to finish.
Note: When using the overlay screen, the own ship track will be hidden if the
radar background and own ship track are blue and the “MANUAL” hue
setting is used. In this case, set HUE to other position and then return to
“MANUAL” to show the own ship track in black.
1. OPERATIONAL OVERVIEW
1-1 1
1.6 Selecting a Display
1.6.1 Display modes
If you have a navigator and network sounder connected, four full-screen displays
are available: radar, plotter, and video sounder and navigation data.
(MODEL1722C/1723C series have five screens, those mentioned above plus
the overlay screen.) In addition to the full-screen display, you can divide the
screen into half-screen combination displays to show two sets of images (data).
Full screen
(Ex. radar)
Combination screen
(Ex. radar + sounder)
Overlay screen
(Radar and plotter,
color model only.
Requires L/L data)
Display screens
The table below shows the displays available with each screen type.
Screen type and available display screen
Full scr e en
Combination screen
options
Overlay screen options
(Color series only)
Radar, plotter, sounder,
nav data
Radar, plotter, echo
sounder, compass,
highway,
compass/highway, nav
data, overlay
Radar + plotter
1. OPERATIONAL OVERVIEW
1-12
1.6.2 Selecting a display
1. Press the [DISP] key to show the full-screen selection window. The icons of
modes not available are marked with “X” mark. PAGE1-PAGE5 are
user-arrangeable displays called “hot pages,” which you can configure as you
like. For further details, see “5.6 Hot Page Setup.”
PAGE1 PAGE2 PAGE3 PAGE4 PAGE5
RADAR PLOT SNDR NAV OVRLY
· TURN KNOB TO SELECT MODE
AND PUSH KNOB TO ENTER.
· PUSH ANY SOFT KEY TO
SELECT IMAGE SOURCE.
Basic display
screens
Hot pages
Full-screen s election w indow (“overlay” for color model)
2. Rotate the [ENTER] knob to select a basic display screen or a hot page
screen.
3. Push the [ENTER] knob. If you selected a basic display screen, a set of
combination display screens corresponding to the basic display screen that
was selected appear. In the example below, radar combination displays are
shown.
PUSH ENTER KNOB.
Radar combination screen s election w indow
4. Operate the [ENTER] knob to select the combination screen display desired
and push it to set.
1. OPERATIONAL OVERVIEW
1-13
1.6.3 Switching control in com bination and overlay screens
A soft key is provided in relevant combination and overlay screens (color series
only) to switch control between displays. In the example below, the RADAR
CNTRL and PLOTTR CNTRL soft keys enable switching control between the
radar and plotter screens in the plotter/radar combination display.
+
359.9
°
R
11.7nm
FISH
WP-002
34° 22. 3456'N 359.9°M
TRIP
NU
080° 22. 3456'E
19.9 kt 99.9 nm
MARK
ENTRY
MODE
NTH UP
NAV
POS
PLOTTR
CCNTRL
PLOTTR
CNTRL
CNTL
RADAR
RADAR
CNTRL
To adjust
plotter
To adjust
radar
Radar display selected Plotter display selected
16.0nm
12
3nm
LP
H-UP
+
359.9
°
R
11.7nm
FISH
WP-002
34° 22. 3456'N 359.9°M
TRIP
NU
080° 22. 3456'E
19.9 kt 99.9 nm
16.0nm
12
3nm
LP
H-UP
SIGNAL
PROC.
RADAR
CNTRL
RADAR
DISPL Y
NAV
FUNC
T ARGET
ST-BY
ST-BY
How to switch control betw een modes in the plotter/radar c ombinati on display
1. OPERATIONAL OVERVIEW
1-14
1.6.4 Selecting radar source
When other network radar is connected to the equipment, you may select an
image source as shown below. This is not necessary when no other network
radar is connected. Select one host name for the source though there are two or
three radar units on the net.
Note: Turn the power off whenever changing the source.
1. Press the [DISP] key.
2. Press any soft key to show the following display.
RADAR SOURCE
RADAR
- - -
SOUNDER SOURCE*
SOUNDER
-
IP ADDRESS
172.031.003.001
HOST NAME
RADAR
- - -
▲
SELECT
SOURCE
EDIT
RETURN
IF THERE IS MORE THAN
ONE NETWORK RADAR OR
ECHO SOUNDER, YOU MAY
SELECT THE IMAGE
SOURCES FOR DISPLAY.
*: Do not change this setting.
Select sourc e menu
3. Use the cursor pad to select RADAR SOURCE and press the EDIT key.
RADAR SOURCE
RADAR
- - -
Radar source
Radar source and s ounder source windows
4. Use the cursor pad and [ENTER] knob to enter source host name: ◄ or ► to
select position and rotate the [ENTER] knob to select character.
5. Press the [ENTER] soft key or [ENTER] knob.
6. Confirm that the correct host name is entered.
7. Press the [DISP] key to finish.
8. Turn the power off and on again.
Note: Sources names are determined at installation. For example, the source
names for radars in a two radar system might be “RADAR” and
“RADAR1”.
1. OPERATIONAL OVERVIEW
1-15
1.7 Data Boxes
Data boxes, providing navigation data, may be shown on any full-screen display.
Up to six data boxes (two in case of large characters) may be shown, and the
default data boxes are position (in latitude and longitude), course over ground,
speed over ground, trip log and cursor position. The user may choose which
data to display, where to locate it, and show or hide it as desired. In addition,
data boxes may be set independently for each display mode (radar, plotter,
sounder). For how to select data for the data boxes, see paragraph “5.5 Data
Boxes Setup”.
.250/ 319.9
°
M
.125nm
SP
H-UP
Data boxes
MODE
NTH UP
NAV
POS
MARK
ENTRY
D.BOX
ON /OFF
TRIP LOG
177
nm
POSITION
47
°
58.535'N
122
°
36.496'W
COG
323.6
°
M
SOG
20.0
kt
350.4
°
M
0.000 nm
Plotter dis play, showing data boxes
1.7.1 Showing, hiding data boxes with soft key
Radar: ZOOM & D. BOX → D. BOX ON/OFF (EBL/VRM data box, cursor data
box also shown/hidden)
Plotter: D. BOX ON/OFF
Sounder: AUTO/D. BOX
→D. BOX ON/OFF
1.7.2 Rearranging data boxes
You may select the location for data boxes as follows:
1. Using the cursor pad, move the cursor to the data box you wish to move. As
the cursor enters the box it changes to a hand. Push the [ENTER] knob, and
the hand changes to a fist, meaning the box is correctly selected.
2. Use the cursor pad to drag the data box to the location desired and push the
[ENTER] knob.
1.7.3 Temporarily erasing a da ta box
You may temporarily erase a data box. Use the cursor pad to place the cursor
inside the data box you wish to erase and press the [CLEAR] key. To redisplay
the box, press the ZOOM & D.BOX soft key D.BOX soft key to display it.
1. OPERATIONAL OVERVIEW
1-16
1.8 Function Keys
The function keys provide for one-touch call up of a desired function. The default
function key settings are as shown in the table below.
Default Setting, Key Label
Function
Key
Radar Plotter Echosounder
#1
Heading line on/off,
HL
Track on/off, TRK TLL output, TLL
#2 Rings on/off, RNG Edit mark/line, EML Clutter, CLT
#3 Echo trail, TRL Ruler, RUL Signal level, SLV
#4 Offcenter, SFT
Add new waypoint,
ADD
Noise limiter, NL
#5 Radar source, RSR
Waypoint
alphanumeric list,
ALP
Picture advance, PA
1.8.1 Executing a function
1. Press the [HIDE/SHOW] key to replace the preset soft key labels with the
function key labels.
34° 22. 3456'N 359.9°M
TRIP
NU
080° 22. 3456'E
19.9 kt 99.9 nm
BRIDGE
FISH
002WP
Function
keys
T
R
K
E
M
L
R
U
L
A
D
D
A
L
p
Plotter
16.0nm
.250/ 319.9
°M
.125nm
SP
H-UP
Function
keys
TARGET
+
359.9°R
0.24nm
H
L
R
N
G
T
R
L
S
F
T
R
S
R
Radar
Function keys
2. Press function key desired.
Note: Function keys can be individually programmed for the radar, plotter and
sounder displays. For further details see the following:
Radar: paragraph 5.2.3
Plotter: paragraph 5.3.2
Sounder: paragraph 5.9.4
Loading...