Funai DCV603 User Manual
VIDEO CASSETTE
RECORDER
DCV603
OWNER’S MANUAL
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The caution marking is located on the rear of the cabinet.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFEGUARDS
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND
CLAMP
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
S2898A
1. Read Instructions- All the safety and operating instructions should be
read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions should be
retained for future reference.
3. Heed Warnings- All warnings on the appliance and in the operating
instructions should be adhered to.
4. Follow Instructions- All operating and use instructions should be followed.
5. Cleaning- Unplug this video product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and, that
for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the
user for cleaning or any other purpose, may exclude the reference to
unplugging the appliance in the cleaning description otherwise required in
item 5.
6. Attachments- Do not use attachments not recommended by the video
product manufacturer as they may cause hazards.
7.Water and Moisture- Do not use this video product near water, for exam-
ple, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. Accessories- Do not place this video product on an unstable cart, stand,
tripod, bracket, or table.The video product may fall, causing serious injury
to a child or adult, and serious damage to the appliance. Use only with a
cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the video product. Any mounting
of the appliance should follow the manufacturer's instructions
and should use a mounting accessory recommended by the
manufacturer.An appliance and cart combination should be
moved with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart combination to
overturn.
9.Ventilation- Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the video product and to protect it from
overheating, and these openings must not be blocked or covered.The
openings should never be blocked by placing the video product on a bed,
sofa, rug, or other similar surface.This video product should not be placed
in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to .
10. Power Sources- This video product should be operated only from the
type of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your appliance dealer or
local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
11. Grounding or Polarization- This video product is equipped with a polar-
ized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the polarized
plug.
12. Power Cord Protection- Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the appliance.
13. Outdoor Antenna Grounding- If an outside antenna or cable system is
connected to the video product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges.Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with regard to proper grounding
of the mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for
the grounding electrode. (Fig. A)
14. Lightning- For added protection for this video product during a lightning
storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the video product due to lightning and powerline surges.
15. Power Lines- An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be fatal.
16. Overloading- Do not overload wall outlets and extension cords as this can
result in a risk of fire or electric shock.
17. Object and Liquid Entry- Never push objects of any kind into this video
product through any openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electr ic shock. Never
spill liquid of any kind on the video product.
18. Servicing- Do not attempt to service this video product yourself as open-
ing or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified ser vice personnel.
19. Damage Requiring Service- Unplug this video product from the wall out-
let and refer servicing to qualified service personnel under the following
conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any way.
f. When the video product exhibits a distinct change in performance-this indi-
cates a need for service.
20. Replacement Parts- When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
21. Safety Check- Upon completion of any service or repairs to this video
product, ask the service technician to perform safety checks to determine
that the video product is in proper operating condition.
22. Heat- This video product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including amplifiers)
that produce heat.
– 1 – EN
0VMN03673 / HD441CD ★★★★
(
)
Indicators
MENU
CHANNEL
POWER
REC/OTR
/STOP
E
JECT
REW
PLAY
F.FWD
TAPE IN
VIDEO L-AUDIO-R
TIMER RECVCR/TVPOWER
13 91110 812 5 43267
1
14 15 16 17 18
TAPE IN TIMER
REC
VCR/TVPOWER
Remote Control
POWER
VCR/TVEJECT
CHANNEL
PAUSE
/STILL
C.RESET
EXIT
SEARCH
-MODE
SLOW
DISPLAYSPEED
STOP
PLAY
RECORD
MENU
REW
F.FWD
123
456
7809
1
3
4
5
6
7
9
11
8
10
17
13
14
16
15
12
2
Rear Panel
ANT
AUDIO
VIDEO
IN
OUT
OUT IN
OUT
L
R
IN
25
19 20 21
242322
(
)
To insert the batteries
PRECAUTIONS
Front Panel
Install Location
For safety and optimum performance of your VCR:
• Install the VCR in a horizontal and stable position. Do not place
anything directly on top of the VCR. Do not place the VCR directly
on top of the TV.
• Shield it from direct sunlight and keep it away from sources of
intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the VCR. Avoid locations subject to strong
vibration or strong magnetic fields.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from AC wall
outlet. Grasp it by the plug.
Moisture Condensation Warning
Moisture condensation may occur inside the unit when it is moved
from a cold place to a warm place, or after heating a cold room or
under conditions of high humidity. Do not use the VCR at least for 2
hours until its inside is dry.
FCC Warning
This equipment may generate or use radio frequency energy.
Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
DESCRIPTION OF CONTROLS
Important Copyright Information
Unauthorized recording or use of broadcast television programming,
video tape, film or other copyrighted material may violate applicable
copyright laws. We assume no responsibility for the unauthorized
duplication, use, or other acts which infringe upon the rights of copyright owners.
A Note about Recycling
This product's packaging materials are recyclable and can be reused.
Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
Note to the Cable TV System Installer
This reminder is provided to call the Cable TV system installer’s
attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding – in particular, specifying that
the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as possible.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
1. Cassette Compartment
2. F.FWD button
3. PLAY button
4. REW button
5. STOP/EJECT button
6. REC/OTR button
7. MENU button
14. POWER indicator
15. VCR/TV indicator
16. TAPE IN indicator
19. AUDIO OUT jacks
20. AUDIO IN jacks
21. ANT. IN jack
22. ANT. OUT jack
18. Indicators
19. Remote Sensor
10. CHANNEL buttons
11. POWER button
12. AUDIO Input jacks
13. VIDEO Input jack
17. TIMER indicator
18. REC indicator
23. VIDEO IN jack
24. VIDEO OUT jack
25. AC Power Cord
1. EJECT button
2. NUMBER buttons
3. MENU button
4. RECORD button
5. SPEED button
6. REW button
7. STOP button
8. PLAY button
9. F.FWD button
10. DISPLAY button
11. PAUSE/STILL button
12. SLOW button
13. C.RESET/EXIT button
14. SEARCH-MODE button
15. CHANNEL buttons
16. POWER button
17. VCR/TV button
Install two AA batteries
(supplied) matching the
polarity indicated on the
bottom of the remote
control.
VIDEO OUT Jack
Connect a video cable going to
the video in jack of a camcorder,
another VCR, a TV, or an audiovisual system (laser disc player,
video disc player, etc.) here.
VIDEO IN Jack
Connect a video cable coming
from the video out jack of a
camcorder, another VCR, or an
audio-visual source (laser disc
player, video disc player, etc.)
here.
AUDIO OUT Jacks
Connect the audio cables going
to the audio in jacks of a camcorder, another VCR, a stereo
amplifier, or an audio system
here.
AUDIO IN Jacks
Connect the audio cables coming from the audio out jacks of a
camcorder, another VCR, or an
audio source here.
– 2 – EN
ANT
IN
OUT
[VHF/UHF
combination antenna]
[Back of the VCR]
IN
OUT
[Cable box or satellite box]
OR
[Indoor antenna]
[Back of the
UHF/VHF combination TV]
UHF/VHF
RF cable
(supplied)
From Cable or
Satellite Company
OR
(
)
(
)
(
)
IN
AUDIO
LR
VIDEO
VIDEO
L
R
OUT IN
OUT IN
AUDIO
[Playing VCR]
[TV A/V]
Audio/Video cables
(not supplied)
PREPARATION FOR USE
(
)
ENGLISH
LANGUAGE SELECT
FRANCAIS
AUTO SET UP
CH 01
SETUP
Connecting to a TV without A/V Terminals
Disconnect the AC power cord of the TV from the AC
outlet.
1
Disconnect the antenna or cable from the TV.
2
Connect the antenna or cable to the ANT. IN jack of
3
the VCR.
Connect the VCR to the TV using the RF cable.
4
Plug the AC power cords of the VCR and TV into the
5
AC outlets.
RF Output Channel
If your TV does not have A/V terminals:
Press [PLAY] on the VCR for 3 seconds during playback.The RF
output channel will change to CH4 from CH3.
When you want to return to CH3 for RF output channel, press
[PLAY] on the VCR for 3 seconds during playback again. (Default
setting :CH3)
• There is case that the RF output channel does not change by situation (For example, when you adjust tracking using
[CHANNEL ].
In this case, stop the playback, and start the playback again.
After that, press [PLAY] on the VCR for 3 seconds.
• If there is a power failure or the VCR is unplugged for more
than 30 seconds, the RF output channel setting will return to
CH3.
Connecting to a TV with A/V Terminals
Using Optional AUDIO/ VIDEO Output Jacks
With this connection, you can get better pictures and sounds
when playing back a tape if your TV has A/V Input jacks. Please
refer to your TV’s owner’s manual.
Using AUDIO/VIDEO Input Jacks
You can use the A/V input jacks on the front or the back of
the VCR.
• To use the input jacks on the back of the VCR, select "L1" position by pressing [0], [0], [1] on the remote control or
[CHANNEL ].
• To use the input jacks on the front of the VCR, select "L2" position by pressing [0], [0], [2] on the remote control or
[CHANNEL ].
•
“L1” or “L2” is found before the lowest memorized channel.
(Example: CH2)
Automatic Channel Set Up
You can automatically program the tuner to scan only the channels you receive in your area.
• Channel memory programming is NOT needed when you connect the VCR to a cable box or satellite box as in "Connect VCR
to TV Connection". In this case, select the VCR and TV to channel 3 or 4 the same channel as the RF output channel of the
VCR. Then, the channel you want to record or view may be
selected at the cable box or satellite box.
•Follow the steps below once. Repeat it only if there is a power
failure or if the VCR is unplugged for more than 30 seconds. (In
these cases, the programmed channels are erased.)
•You must follow the steps below before attempting to play or
record a video tape. If you want to play or record a video tape
BEFORE programming the tuner, you can cancel it by pressing
[C.RESET/EXIT].
You need to connect the antenna or cable to the VCR
1
first. Then, connect the VCR power plug into a standard AC outlet.
Turn on the TV and set the TV to channel 3. If channel 3
2
is already occupied for broadcasting, change the RF output
to CH 4, and change the TV channel to CH4.
(See “RF Output Channel” on page 3 for the detail.)
Turn on the VCR by pressing [POWER]. When the
3
POWER is on, both the POWER and VCR/TV indicator on
the VCR will be on.
Select the On Screen Language
4
("ENGLISH" , "FRANCAIS" or
"ESPAÑOL") by pressing [PLAY] or
[STOP]. Then, press [F.FWD].
Begin channel preset by pressing [F.FWD] once. The
5
tuner scans and memorizes all active
channels in your area.
• The VCR distinguishes between standard
TV channels and cable channels.
After scanning, the tuner stops on the lowest memo-
6
rized channel. The TV screen returns to TV mode.
• If "AUTO SET UP" appears on the TV screen again, check
the cable connections. Press [F.FWD] once again and the
VCR will begin preset again.
To Select a Desired Channel
You can select the desired channel by using [CHANNEL ]
or directly pressing [Number] on the remote control.
Note for using the Number buttons:
• When selecting cable channels which are higher than 99,
enter channel numbers as a three-digit number.(For example:
117, press 1,1,7)
• You must precede single-digit channel numbers with a zero
(For example: 02, 03, 04 and so on).
To Preset the Channel Again
Press [MENU] until the main menu appears.
1
Select "CHANNEL SET UP" by pressing [PLAY] or
2
[STOP]. Then, press [F.FWD].
Select "AUTO SET UP" by pressing [PLAY] or [STOP].
3
Then, press [F.FWD]. After scanning, the tuner stops on
the lowest memorized channel.
– 3 – EN
To Add/Delete Channels
(
)
(
)
(
)
(
)
CLOCK SET
MONTH DAY YEAR
03 / 17 MON 2003
HOUR MINUTE AM/PM
05 : 40 PM AM
PM
Press [PLAY] or [STOP]repeatedly.
Then, press [F.FWD].
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
The day of the week will appear automatically.
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
Press [PLAY] or [STOP]
repeatedly.
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
Set the month
Set the day
Set the year
Set the hour
Set the minute
Set the AM
or PM
- MENU -
TIMER PROGRAMMING
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
SAP
[OFF]
[ON]
When the VCR automatically program the tuner to scan only the
channels you receive in your area, some channels may be
skipped due to weak signal. You can manually add the channel
in the VCR memory.
Press [MENU] until the main menu
1
appears.
Select "CHANNEL SET UP" by
2
pressing [PLAY] or [STOP]. Then,
press [F.FWD].
Select "MANUAL SET UP" by pressing [PLAY] or
3
[STOP]. Then, press [F.FWD].
Enter the desired channel number by pressing [PLAY]
4
or [STOP].
Add or Delete it from memory by pressing [F.FWD] or
5
[REW] so that "ADD" or "DELETE" flashes on the TV
screen accordingly.
Exit the Preset mode by pressing [C.RESET/EXIT].
6
To Change the On-Screen Language
Press [MENU] until the main menu appears.
1
Select "LANGUAGE SELECT" by pressing [PLAY] or
2
[STOP]. Then, press [F.FWD].
Select "ENGLISH" , "FRANCAIS" or "ESPAÑOL" by
3
pressing [PLAY] or [STOP]. Then, press
[C.RESET/EXIT].
• If you accidentally select Spanish or French and need
English: Press [MENU] and choose SELEC. IDIOMA, or
SELECTION LANGUE. Press [F.FWD], and select ENGLISH. Finally, press [C.RESET/EXIT].
Clock Set Up
Select main menu by pressing [MENU].(If the clock is not
1
set, the CLOCK SET menu appears first. In this case, follow step [3].)
Select "CLOCK SET" by pressing [PLAY] or [STOP].
2
Then, press [F.FWD].
Set the clock.
3
• To go back one step, press [REW].
4
Start the clock by pressing [C.RESET/EXIT] or [F.FWD].
PLAYBACK FUNCTION
Normal Playback
Insert the prerecorded tape. The VCR will
1
turn on. If the safety tab has been removed,
the VCR will start playback automatically.
Turn on the TV and set the TV to channel 3. If channel
2
3 is already occupied for broadcasting, change the RF output to CH 4, and change the TV channel to CH4.
(See “RF Output Channel” on page 3 for the detail.)
Begin playback by pressing [PLAY].
3
• Tracking adjustment will be set automatically (Digital
Tr acking function) when you start playback. To adjust the
tracking manually, press [CHANNEL ]
• You cannot manually adjust the tracking of a Still picture.
However, you may press [CHANNEL ]
remove vertical jitter in a Still picture.
• When a tape has reached the end, the VCR will rewind the
tape to the beginning, eject the tape, and turn off the VCR
automatically.
To stop playback, press [STOP].
on the VCR.
on the VCR to
4
Counter Reset
• You can reset the counter by pressing [C.RESET/EXIT] on the
remote control
Still / Slow
You can freeze the picture on TV screen by pressing
[PAUSE/STILL] during playback.
• You can advance the picture by one frame at a time by pressing [PAUSE/STILL] during the still mode.
• If the picture begins to vibrate vertically during the still mode,
stabilize the picture by pressing [CHANNEL ].
• If the picture is distorted or rolling vertically, adjust the vertical
hold control on your TV, if equipped.
You can see the slow motion by pressing [SLOW] during playback or the still mode.
• If the noise bar appears on the TV screen, you can reduce it
by pressing [CHANNEL ].
• After the VCR has been in Still/Slow mode for 5 minutes, it will
stop automatically to protect the tape and the video head from
damage.
• To return playback, press [PLAY].
Auto Repeat Playback
This feature allows you to play a tape over and over.
Select main menu by pressing [MENU].
1
Select "AUTO REPEAT" by pressing [PLAY] or [STOP].
2
Begin auto repeat playback by pressing [F.FWD] so that
3
[ON] appears next to "AUTO REPEAT".
• If the on-screen menu still remains, press [C.RESET/EXIT]
to exit the menu.
• To cancel the Auto repeat mode, press [F.FWD] at step [3]
so that [OFF] appears next to "AUTO REPEAT".
Search Functions
Picture Search
If you want to skip or repeat a scene during playback, press
[F.FWD] or [REW].
• Press it again and the VCR will now search in super high
speed. (in the LP/SLP modes only)
– 4 – EN
(
)
Record safety tab
Type of tape T60 T120 T160
SP mode 1hour 2hours 2-2/3hours
SLP mode 3hour 6hour 8hour
Tape Speed Recording/Playback Time
Select once, daily or weekly recording
Set the tape speed
Set the channel number
Set the end time
Set the start time
Set the date
Set the program number (1~8)
Press [PLAY] or [STOP] repeatedly for the desired channel number.
Then, press [F.FWD].
If you connected the VCR to a cable box or satellite box as in "Connect
VCR to TV" on page 3, select the VCR to channel 3 or 4 the same channel
as RF output channel of the VCR.
Then, select the channel you want to record at the cable box or satellite box.
Leave the cable box or satellite box on for timer recording.
Press [PLAY] or [STOP] repeatedly for the
desired
tape speed.
Then, press [F.FWD].
Program number which is not set up flashes.
Press [PLAY] or [STOP] repeatedly for the
desired program number.Then, press [F.FWD].
First, press [PLAY] or [STOP] for the month. Then, press [F.FWD].
Next, press [PLAY] or [STOP] for the day. Then, press [F.FWD].
First, press [PLAY] or [STOP] for the hour. Then, press [F.FWD].
Next, press [PLAY] or [STOP] for the minute. Then, press [F.FWD]
.
And then, press [PLAY] or [STOP] for AM or PM. Then, press [F.FWD]
.
Follow the instructions of "Set the start time" to set the end time.
For weekly:
Press [PLAY] or [STOP] to point to
"WEEKLY".
Then, press [F.FWD].
For daily (Monday~Friday):
Press [PLAY] or
[STOP] to point to "DAILY".
PROGRAM NUMBER 4
ONCE
DAILY
WEEKLY
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 05/12 MON
START TIME 07:30 PM
END TIME 08:30 PM
CHANNEL 16
REC SPEED SP
SP
SLP
PROGRAM NUMBER 4
DATE - - / - START TIME - - : - - - END TIME - - : - - - CHANNEL - REC SPEED - -
For once:
Press [PLAY] or [STOP] to point to "ONCE".
• To go back one step, press [REW].
Index Search
REC OTR(0:30) OTR(1:00).....
(Normal recording)
OTR(8:00) OTR(7:30)
An index mark will be assigned at the beginning of each recordings you make. You may skip to a specific marked point by following the steps below.
P
ress [SEARCH-MODE] so that the Index Search menu
1
appears.
Enter the number of recordings you
2
wish to skip by pressing [PLAY] or
[STOP] within 30 seconds.
Press [F.FWD] or [REW] to start index search. If you
3
want to go in the forward direction, press [F.FWD]. If you
want to go in the reverse direction, press [REW].
•
After index search, the VCR will play the tape automatically.
Time Search
This feature allows you to go to a specific point on a tape by
entering the exact amount of time you wish to skip in order to
reach the point.
Press [SEARCH-MODE] so that the Time Search menu
1
appears.
Enter your desired time to skip by
2
pressing [PLAY] or [STOP] within 30 seconds.
Press [F.FWD] or [REW] to start time search. If you want
3
to go in the forward direction, press [F.FWD]. If you want
to go in the reverse direction, press [REW].
•
After time search, the VCR will play the tape automatically.
INDEX SEARCH
03
TIME SEARCH
2 : 50
OTR (One Touch Recording)
This feature allows you to set the recording length simply by
pressing [REC/OTR] on the VCR.
Begin OTR by pressing [REC/OTR] on the VCR repeat-
1
edly until the desired recording length appears.
TIMER RECORDING
You may set the VCR to start recording while you are away.You
can set eight programs to record on specific days, daily or weekly within a 1 year period.
Insert a tape with its safety tab into the VCR.
1
Select main menu by pressing [MENU].
2
Select "TIMER PROGRAMMING" by pressing [PLAY] or
3
[STOP]. Then, press [F.FWD].
• If you have not yet set the clock, "CLOCK SET" appears. If
so, continue with the step [3] in "CLOCK SET UP" section.
Then, set the timer recording.
Set the timer.
4
RECORDING FUNCTION
It may be unlawful to record play back copyrighted material without the consent of the copyright owner.
Accidental erasure prevention
To prevent accidental recording on a recorded
cassette, remove its record safety tab. To
record on it later, cover the hole with cellophane tape.
Before recording, make sure:
•
The desired channel is selected by pressing [Number] on
the remote control or the [CHANNEL ]. (If you connected the VCR to a cable box or satellite box as in "VCR
to TV Connection" on page 3, select the VCR to channel
3 or 4 the same channel as the RF output channel of the
VCR. Then, select the channel you want to record at the
cable box or satellite box. In this case, you can ONL
record and view the SAME
• There is a tape with its safety tab into the VCR.
• The desired recording speed is selected in SP(standard play) or
SLP(super long play) mode by pressing [SPEED] on the remote
control.
• TV STEREO or SAP is selected.
Viewing and Recording the Same Program
Begin the recording by pressing [RECORD].
channel. )
1
• To temporarily stop recording or resume it, press
[PAUSE/STILL]. After the VCR has been in Pause mode for
5 minutes, it will stop automatically to protect the tape and
the video head from damage.
Press [STOP] when recording is completed.
2
Y
5
6
– 5 – EN
To set another program, repeat step [4]. To exit, press
[C.RESET/EXIT].
Press [POWER] to set the timer. The TIMER indicator on
the VCR comes on.
ACTIVATED UNLESS YOU TURN THE VCR OFF.
TIMER RECORDING WILL NOT BE
Loading...