Funai DCV203 User Manual

OWNER’S MANUAL

VIDEO CASSETTE RECORDER

DCV203

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The caution marking is located on the rear of the cabinet.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT SAFEGUARDS

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

ANTENNA LEAD WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

S2898A

1. Read Instructions- All the safety and operating instructions should be

read before the appliance is operated.

2. Retain Instructions- The safety and operating instructions should be

retained for future reference.

3. Heed Warnings- All warnings on the appliance and in the operating

instructions should be adhered to.

4. Follow Instructions- All operating and use instructions should be followed.

5.Cleaning- Unplug this video product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.

6. Attachments- Do not use attachments not recommended by the video

product manufacturer as they may cause hazards.

7.Water and Moisture- Do not use this video product near water, for exam-

ple, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8. Accessories- Do not place this video product on an unstable cart, stand,

tripod, bracket, or table.The video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer.An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

9.Ventilation- Slots and openings in the cabinet are provided for ventilation

and to ensure reliable operation of the video product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the video product on a bed, sofa, rug, or other similar surface.This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to .

10. Power Sources- This video product should be operated only from the

type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

11. Grounding or Polarization- This video product is equipped with a polar-

ized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12. Power Cord Protection- Power supply cords should be routed so that

they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

13. Outdoor Antenna Grounding- If an outside antenna or cable system is

connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

14. Lightning- For added protection for this video product during a lightning

storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and powerline surges.

15. Power Lines- An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16. Overloading- Do not overload wall outlets and extension cords as this can

result in a risk of fire or electric shock.

17. Object and Liquid Entry- Never push objects of any kind into this video

product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electr ic shock. Never spill liquid of any kind on the video product.

18. Servicing- Do not attempt to service this video product yourself as open-

ing or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified ser vice personnel.

19. Damage Requiring Service- Unplug this video product from the wall out-

let and refer servicing to qualified service personnel under the following conditions:

a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the video product. c. If the video product has been exposed to rain or water. d. If the video product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation.

e. If the video product has been dropped or damaged in any way.

f. When the video product exhibits a distinct change in performance-this indi-

cates a need for service.

20. Replacement Parts- When replacement parts are required, be sure the

service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

21. Safety Check- Upon completion of any service or repairs to this video

product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition.

22. Heat- This video product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

– 1 – EN

0VMN03674 / HD230CD ★★★★

(

)

Display Window

CHANNEL

POWER

TAPE IN

TIMER

REC

VCR/TV

POWER

VIDEO AUDIO

REC/OTR

REW

F.FWD

STOP/EJECT

PLAY

1213 911 10 8 5 4 3 267

14 15 16 17 18

TAPE IN

TIMER

REC

VCR/TV

POWER

Remote Control

POWER

VCR/TVEJECT

CHANNEL

PAUSE

/STILL

EXIT

RESET

AUTO-

REPEAT

COUNTER

MEMORY

DISPLAYSPEED

STOP

PLAY

RECORD

REW

F.FWD

123

456

7809

4 5

Rear Panel

ANT

AUDIO

VIDEO

OUT

OUT IN

19 20 21

242322

(

)

To insert the batteries

PRECAUTIONS

Front Panel

Install Location

For safety and optimum performance of your VCR:

• Install the VCR in a horizontal and stable position. Do not place anything directly on top of the VCR. Do not place the VCR directly on top of the TV.

• Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the VCR. Avoid locations subject to strong vibration or strong magnetic fields.

Avoid the Hazards of Electrical Shock and Fire

• Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it from AC wall

outlet. Grasp it by the plug.

Moisture Condensation Warning

Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do not use the VCR at least for 2 hours until its inside is dry.

FCC Warning

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

DESCRIPTION OF CONTROLS

Important Copyright Information

Unauthorized recording or use of broadcast television programming, video tape, film or other copyrighted material may violate applicable copyright laws. We assume no responsibility for the unauthorized duplication, use, or other acts which infringe upon the rights of copyright owners.

A Note about Recycling

This product's packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

Note to the Cable TV System Installer

This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding – in particular, specifying that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

1. Cassette Compartment

2. F.FWD button

3. PLAY button

4. REW button

5. STOP/EJECT button

6. REC/OTR button

7. MENU button

14. POWER indicator

15. VCR/TV indicator

16. TAPE IN indicator

19. AUDIO OUT jack

20. AUDIO IN jack

21. ANT. IN jack

22. ANT. OUT jack

1. EJECT button

2. NUMBER buttons

3. MENU button

4. RECORD button

5. SPEED button

6. REW button

7. STOP button

8. PLAY button

18. Display Window

19. Remote Sensor

10. CHANNEL buttons

11. POWER button

12. AUDIO Input jack

13. VIDEO Input jack

9. F.FWD button

10. DISPLAY button

11. PAUSE/STILL button

12. COUNTER MEMORY button

13. COUNTER RESET/EXIT button

14. AUTO REPEAT button

15. CHANNEL buttons

16. POWER button

17. VCR/TV button

Install two AA batteries (supplied) matching the polarity indicated on the

17. TIMER indicator

18. REC indicator

23. VIDEO IN jack

24. VIDEO OUT jack

25. AC Power Cord

bottom of the remote control.

VIDEO OUT Jack

Connect a video cable going to the video in jack of a camcorder, another VCR, a TV, or an audiovisual system (laser disc player, video disc player, etc.) here.

VIDEO IN Jack

Connect a video cable coming from the video out jack of a camcorder, another VCR, or an audio-visual source (laser disc player, video disc player, etc.) here.

AUDIO OUT Jack

Connect the audio cable going to the audio in jack of a camcorder, another VCR, a stereo amplifier, or an audio system here.

AUDIO IN Jack

Connect the audio cable coming from the audio out jack of a camcorder, another VCR, or an audio source here.

– 2 – EN

[VHF/UHF combination antenna]

[Back of the VCR]

OUT

[Cable box or satellite box]

[Indoor antenna]

[Back of the

UHF/VHF combination TV]

UHF/VHF

RF cable (supplied)

From Cable or Satellite Company

ANT

OUT

(

)

(

)

(

)

[TV A/V]

AUDIO

VIDEO

OUT IN

AUDIO

[Playing VCR]

Audio/Video cables

(not supplied)

PREPARATION FOR USE

(

)

ENGLISH

LANGUAGE SELECT

FRANCAIS

AUTO SET UP

CH 01

SETUP

Connecting to a TV without A/V Terminals

Disconnect the AC power cord of the TV from the AC

outlet. Disconnect the antenna or cable from the TV.

Connect the antenna or cable to the ANT. IN jack of

the VCR. Connect the VCR to the TV using the RF cable.

Plug the AC power cords of the VCR and TV into the

AC outlets.

RF Output Channel

If your TV does not have A/V terminals:

Press [PLAY] on the VCR for 3 seconds during playback.The RF output channel will change to CH4 from CH3. When you want to return to CH3 for RF output channel, press [PLAY] on the VCR for 3 seconds during playback again. (Default setting :CH3)

• There is case that the RF output channel does not change by situation (For example, when you adjust tracking using [CHANNEL ]. In this case, stop the playback, and start the playback again. After that, press [PLAY] on the VCR for 3 seconds.

• If there is a power failure or the VCR is unplugged for more than 30 seconds, the RF output channel setting will return to CH3.

Connecting to a TV with A/V Terminals

Using Optional AUDIO/ VIDEO Output Jacks

With this connection, you can get better pictures and sounds when playing back a tape if your TV has A/V Input jacks. Please refer to your TV’s owner’s manual.

Using AUDIO/VIDEO Input Jacks

You can use the A/V input jacks on the front or the back of the VCR.

• To use the input jacks on the back of the VCR, select "L1" position by pressing [0], [0], [1] on the remote control or [CHANNEL ].

• To use the input jacks on the front of the VCR, select "L2" position by pressing [0], [0], [2] on the remote control or [CHANNEL ].

•

“L1” or “L2” is found before the lowest memorized channel.

(Example: CH2)

Automatic Channel Set Up

You can automatically program the tuner to scan only the channels you receive in your area.

• Channel memory programming is NOT needed when you connect the VCR to a cable box or satellite box as in "Connect VCR to TV Connection". In this case, select the VCR and TV to channel 3 or 4 the same channel as the RF output channel of the VCR. Then, the channel you want to record or view may be selected at the cable box or satellite box.

• Follow the steps below once. Repeat it only if there is a power failure or if the VCR is unplugged for more than 30 seconds. (In these cases, the programmed channels are erased.)

• You must follow the steps below before attempting to play or record a video tape. If you want to play or record a video tape BEFORE programming the tuner, you can cancel it by pressing [COUNTER RESET/EXIT].

You need to connect the antenna or cable to the VCR

first. Then, connect the VCR power plug into a standard AC outlet.

Turn on the TV and set the TV to channel 3. If channel 3

is already occupied for broadcasting, change the RF output to CH 4, and change the TV channel to CH4. (See “RF Output Channel” on page 3 for the detail.)

Turn on the VCR by pressing [POWER]. When the

POWER is on, both the POWER and VCR/TV indicator on

the VCR will be on.

Select the On Screen Language

("ENGLISH" , "FRANCAIS" or "ESPAÑOL") by pressing [PLAY] or

[STOP]. Then, press [F.FWD].

Begin channel preset by pressing [F.FWD] once. The

tuner scans and memorizes all active channels in your area.

• The VCR distinguishes between standard

TV channels and cable channels.

After scanning, the tuner stops on the lowest memo-

rized channel. The TV screen returns to TV mode.

• If "AUTO SET UP" appears on the TV screen again, check

the cable connections. Press [F.FWD] once again and the VCR will begin preset again.

To Select a Desired Channel

You can select the desired channel by using [CHANNEL ] or directly pressing [Number] on the remote control.

Note for using the Number buttons:

• When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.(For example: 117, press 1,1,7)

• You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).

To Preset the Channel Again

Press [MENU] until the main menu appears.

Select "CHANNEL SET UP" by pressing [PLAY] or

[STOP]. Then, press [F.FWD].

Select "AUTO SET UP" by pressing [PLAY] or [STOP].

Then, press [F.FWD]. After scanning, the tuner stops on the lowest memorized channel.

– 3 – EN

To Add/Delete Channels

(

)

(

)

(

)

CLOCK SET

MONTH DAY YEAR 03 / 17 MON 2003

HOUR MINUTE AM/PM

05 : 40 PM AM

Press [PLAY] or [STOP]repeatedly. Then, press [F.FWD].

Press [PLAY] or [STOP] repeatedly. Then, press [F.FWD]. The day of the week will appear automatically.

Press [PLAY] or [STOP] repeatedly. Then, press [F.FWD].

Press [PLAY] or [STOP] repeatedly.

Press [PLAY] or [STOP] repeatedly. Then, press [F.FWD].

Set the month

Set the day

Set the year

Set the hour

Set the minute

Set the AM or PM

- MENU -

TIMER PROGRAMMING AUTO REPEAT CHANNEL SET UP CLOCK SET LANGUAGE SELECT

[OFF]

When the VCR automatically program the tuner to scan only the channels you receive in your area, some channels may be skipped due to weak signal. You can manually add the channel in the VCR memory.

Press [MENU] until the main menu

appears.

Select "CHANNEL SET UP" by

pressing [PLAY] or [STOP]. Then, press [F.FWD].

Select "MANUAL SET UP" by pressing [PLAY] or

[STOP]. Then, press [F.FWD].

Enter the desired channel number by pressing [PLAY]

or [STOP].

Add or Delete it from memory by pressing [F.FWD] or

[REW] so that "ADD" or "DELETE" flashes on the TV screen accordingly.

Exit the Preset mode by pressing [COUNTER

RESET/EXIT].

To Change the On-Screen Language

Press [MENU] until the main menu appears.

Select "LANGUAGE SELECT" by pressing [PLAY] or

[STOP]. Then, press [F.FWD].

Select "ENGLISH" , "FRANCAIS" or "ESPAÑOL" by

pressing [PLAY] or [STOP]. Then, press [COUNTER RESET/EXIT].

• If you accidentally select Spanish or French and need English: Press [MENU] and choose SELEC. IDIOMA, or SELECTION LANGUE. Press [F.FWD], and select ENGLISH. Finally, press [COUNTER RESET/EXIT].

Clock Set Up

Select main menu by pressing [MENU].(If the clock is not

set, the CLOCK SET menu appears first. In this case, follow step [3].)

Select "CLOCK SET" by pressing [PLAY] or [STOP].

Then, press [F.FWD].

Set the clock.

• To go back one step, press [REW].

Start the clock by pressing [COUNTER RESET/EXIT] or

[F.FWD].

PLAYBACK FUNCTION

Normal Playback

Insert the prerecorded tape. The VCR will

turn on. If the safety tab has been removed,

the VCR will start playback automatically.

Turn on the TV and set the TV to channel 3. If channel

3 is already occupied for broadcasting, change the RF out-

put to CH 4, and change the TV channel to CH4. (See “RF Output Channel” on page 3 for the detail.)

Begin playback by pressing [PLAY].

•

Tracking adjustment will be set automatically (Digital Tracking function) when you start playback. To adjust the tracking manually, press [CHANNEL ] on the VCR.

• You cannot manually adjust the tracking of a Still pic-

ture. However, you may press [CHANNEL ] on the VCR to remove vertical jitter in a Still picture.

• When a tape has reached the end, the VCR will rewind the tape to the beginning, eject the tape, and turn off the VCR automatically.

To stop playback, press [STOP].

Counter Reset

• You can reset the counter by pressing [COUNTER RESET/EXIT] on the remote control

Still Picture

Press [PAUSE/STILL] during playback to view a still picture on the TV screen. ¡ If you press [PAUSE/STILL] to freeze the picture, usually there

will be noise lines on the TV screen. This is normal, however, each time you press [PAUSE/STILL], the lines will change position.

¡ When the picture begins to vibrate vertically, stabilize the pic-

ture by pressing mode

¡ After the VCR has been in Still mode for 5 minutes, it will stop

¡ To return to playback, press [PLALY].

This feature allows you to play a tape over and over.

automatically to protect the tape and the video head.

Auto Repeat Playback

Select main menu by pressing [MENU].

[CHANNEL ]

on the VCR in the Still

Select "AUTO REPEAT" by pressing [PLAY] or

[STOP].

Begin auto repeat playback by pressing [F.FWD]

so that [ON] appears next to "AUTO REPEAT".

• If the on-screen menu still remains, press [COUNTER RESET/EXIT] to exit the menu.

•

You can set AUTO REPEAT to ON or OFF by pressing the AUTO REPEAT button on the remote control, too.

• When you set the Auto repeat mode to [ON] while the

Counter memory mode is ON, the VCR will exit the Counter memory mode automatically.

•

To cancel the Auto repeat mode, press [F.FWD] at step [3] so that [OFF] appears next to "AUTO REPEAT".

Search Functions

Picture Search

If you want to skip or repeat a scene during playback, press [F.FWD] or [REW].

• Press it again and the VCR will now search in super high speed. (in the LP/SLP modes only)

– 4 – EN

(

)

Record safety tab

Type of tape T60 T120 T160

SP mode 1hour 2hours 2-2/3hours SLP mode 3hour 6hour 8hour

Tape Speed Recording/Playback Time

RECORDING FUNCTION

Select once, daily or weekly recording

Set the tape speed

Set the channel number

Set the end time

Set the start time

Set the date

Set the program number (1~8)

Press [PLAY] or [STOP] repeatedly for the desired channel number. Then, press [F.FWD]. If you connected the VCR to a cable box or satellite box as in "Connect VCR to TV" on page 3, select the VCR to channel 3 or 4 the same channel as RF output channel of the VCR. Then, select the channel you want to record at the cable box or satellite box. Leave the cable box or satellite box on for timer recording.

Press [PLAY] or [STOP] repeatedly for the desired

tape speed.

Then, press [F.FWD].

Program number which is not set up flashes. Press [PLAY] or [STOP] repeatedly for the desired program number.Then, press [F.FWD].

First, press [PLAY] or [STOP] for the month. Then, press [F.FWD]. Next, press [PLAY] or [STOP] for the day. Then, press [F.FWD].

First, press [PLAY] or [STOP] for the hour. Then, press [F.FWD]. Next, press [PLAY] or [STOP] for the minute. Then, press [F.FWD]

And then, press [PLAY] or [STOP] for AM or PM. Then, press [F.FWD]

Follow the instructions of "Set the start time" to set the end time.

For weekly:

Press [PLAY] or [STOP] to point to "WEEKLY". Then, press [F.FWD].

For daily (Monday~Friday):

Press [PLAY] or

[STOP] to point to "DAILY".

PROGRAM NUMBER 4 ONCE DAILY WEEKLY

ONE TIME PROGRAM

PROGRAM NUMBER 4 DATE 05/12 MON START TIME 07:30 PM END TIME 08:30 PM CHANNEL 16 REC SPEED SP SP SLP

PROGRAM NUMBER 4 DATE - - / - START TIME - - : - - - END TIME - - : - - - CHANNEL - REC SPEED - -

For once:

Press [PLAY] or [STOP] to point to "ONCE".

• To go back one step, press [REW].

REC OTR(0:30) OTR(1:00).....

(Normal recording)

OTR(8:00) OTR(7:30)

It may be unlawful to record play back copyrighted material without the consent of the copyright owner.

Accidental erasure prevention

To prevent accidental recording on a recorded cassette, remove its record safety tab. To record on it later, cover the hole with cellophane tape.

Before recording, make sure:

•

The desired channel is selected by pressing [Number] on the remote control or the [CHANNEL ]. (If you connected the VCR to a cable box or satellite box as in "VCR to TV Connection" on page 3, select the VCR to channel 3 or 4 the same channel as the RF output channel of the VCR. Then, select the channel you want to record at the cable box or satellite box. In this case, you can ONL record and view the SAME channel. )

• There is a tape with its safety tab into the VCR.

• The desired recording speed is selected in SP(standard play) or

SLP(super long play) mode by pressing [SPEED] on the remote control.

Viewing and Recording the Same Program

Begin the recording by pressing [RECORD].

• To temporarily stop recording or resume it, press [PAUSE/STILL]. After the VCR has been in Pause mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage.

Press [STOP] when recording is completed.

TIMER RECORDING

You may set the VCR to start recording while you are away.You can set eight programs to record on specific days, daily or weekly within a 1 year period.

Insert a tape with its safety tab into the VCR.

Select main menu by pressing [MENU].

Select "TIMER PROGRAMMING" by pressing [PLAY] or

[STOP]. Then, press [F.FWD].

• If you have not yet set the clock, "CLOCK SET" appears. If so, continue with the step [3] in "CLOCK SET UP" section. Then, set the timer recording.

Set the timer.

OTR (One Touch Recording)

This feature allows you to set the recording length simply by pressing [REC/OTR] on the VCR.

Begin OTR by pressing [REC/OTR] on the VCR repeat-

edly until the desired recording length appears.

– 5 – EN

To set another program, repeat step [4]. To exit, press

[COUNTER RESET/EXIT].

Press [POWER] to set the timer. The TIMER indicator on

the VCR comes on. TIMER RECORDING WILL NOT BE ACTIVATED UNLESS YOU TURN THE VCR OFF.

+ 11 hidden pages