Funai DCT1304R User Manual

0EMN02396	Printed in Malaysia
	L2207CH * * * * *

	Owner’s	13 INCH
	Manual
		COLOR TELEVISION
		DCT1304R

FEATURES

●Tinted, Bright Black Matrix Picture Tube

●181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.

●PLL Frequency Synthesized Tuning- The latest PLL frequency synthesized electronic tuning system provides free and easy channel selection, and lets you tune directly to any channel using the channel number buttons (0~9 and +100-key) on the remote control.

●On-Screen Function Display

●Full-Function Remote Control

●Sleep Timer

●Closed Caption Decoder- You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program.

●Auto Shut Off Function- If there is no signal input from the antenna terminal and no operation for 15 minutes, the TV will turn itself off automatically.

●V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.

PRECAUTION

●Place your TV in a room with adequate ventilation.

●Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.

●Do not place your TV on soft surfaces, such as rugs or blankets.

●Leave enough room for air to circulate around the bottom, top and back of the set.

The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.

Date of Purchase		Dealer Phone No.
Dealer Purchase from		Model No.
Dealer Address		Serial No.

This Owner’s Manual is made of recycled paper.

ANTENNA/CABLE CONNECTIONS

		Bent pin
				UHF/VHF Rod
	Cable	Plug		Antenna
				(Supplied)
	(Needs to be straightened)		(Straight pin)
	Before plugging the UHF/VHF			VHF
				Antenna
	Rod Antenna (Supplied) into the			(Not supplied)

	ANT(enna). IN jack, check that	UHF
	the pin is not bent. If it is bent,
		Antenna
	straighten the pin as illustrated,	(Not supplied)
	then plug the pin into the
	ANT(enna). IN jack.

ANT. IN

OR

VHF/UHF Combiner (Not supplied)

VHF/UHF Combination Antenna (Not supplied)

*Some cable TV systems use scrambled signals and require a special converter to receive these channels. Consult your local cable company.

CATV Box * or Satellite Box (Not supplied)

OUT IN

75-ohm Coaxial Cable

OR

From Cable System or Satellite Antenna 75-ohm

Coaxial Cable

From Cable System

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

MISE EN GARDE:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

FCC WARNINGThis equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

CLOSED CAPTION

This TV can receive C1 and C2 of Caption and Text.

CAPTION MODE

1)Closed Caption Characters can be displayed on the TV screen only when the received broadcast signal contains Caption Signals.

2)Paint-on mode: Displays input characters on the screen immediately.

Pop-on mode: Once characters are stored in memory, they are displayed all at once. Roll-up mode: Displays the characters continuously by scrolling (max. 4 lines)

Note: If the CAPTION C1 or C2 is selected but a Closed Caption signal is not included, characters will not be displayed.

Notes:

1)When your TV receives a special effects playback signal (i.e., Search, Slow, Still) from a VCR’s video output channel (CH3 or CH4), your TV may not display the correct caption or text.

2)Captions and texts may not match the TV voice exactly.

3)Interference may cause the closed caption system not to function properly.

4)The caption or text characters will not be displayed while the menu display or function’s display is shown.

5)If you see this screen :

TEXT MODE

1)Displays the text on the screen by scrolling (max. 7 lines)

2)If the received broadcast signal does not contain the caption or text signal, no change will occur.

If your TV displays a black box on the screen, this means that your TV is set to TEXT mode. To clear screen, select CAPTION C1, C2 or CAPTION [OFF].

PORTABLE CART WARNING

S3126A

SYMBOLE D'AVERTISSEMENT POUR

LES COMPOSANTES

APPAREIL ET MEUBLE A ROULETTES

S3126A

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

	CAUTION			THIS SYMBOL INDICATES THAT DAN-
				GEROUS VOLTAGE CONSTI-TUTING A
	RISK OF ELECTRIC SHOCK
				RISK OF ELECTRIC SHOCK IS PRE-
	DO NOT OPEN
				SENT WITHIN THIS UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
				THIS SYMBOL INDICATES THAT
SHOCK, DO NOT REMOVE COVER (OR BACK) NO
				THERE ARE IMPORTANT OPERATING
USER SERVICEABLE PARTS INSIDE. REFER SER-
				AND MAINTENANCE INSTRUCTIONS
VICING TO QUALIFIED SERVICE PERSONNEL.
				IN THE LITERATURE ACCOMPANY-ING
The important note is located on the rear of the cabinet.				THE APPLIANCE.

IMPORTANT SAFEGUARDS

1.Read instructions-All the safety and operating instructions should be read before the appliance is operated.

2.Retain Instructions-The safety and operating instructions should be retained for future reference.

3.Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to.

4.Follow Instructions-All operating and use instructions should be followed.

5.Cleaning-Unplug TV from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.

6.Attachments-Do not use attachments not recommended by the TV manufacturer as they may cause hazards.

7.Water and Moisture-Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8.Accessories-Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the TV.

Any mounting of the appliance should follow the man-

ufacturer’s instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

AMEUBLESCet appareil ne doit être placé que sur un meuble (avec ou sans roulettes) recom-

mandé par le fabricant. Si vous l’installez sur un meuble à roulettes, déplacez les deux

ensembles avec précaution. Un

arrêt brusque, l’utilisation d’une force excessive et des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.

9.Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar surface. This TV should never be placed near or over a radiator or heat register. This TV should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to .

10.Power Sources-This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from battery power, or other sources, refer to the operating instructions.

11.Grounding or Polarization-This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12.Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE ANTENNA

LEAD IN WIRE

GROUND

CLAMP

ANTENNADISCHARGE UNIT (NEC SECTION 810-20)

ELECTRIC

SERVICE

EQUIPMENT

NEC - NATIONAL ELECTRICAL CODE

S 2 8 9 8 A

pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

13.Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

14.Lightning-For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges.

15.Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16.Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250, PART H)

18.Servicing-Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19.Damage Requiring Service-Unplug this TV from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power supply cord or plug is damaged or frayed.

b.If liquid has been spilled, or objects have fallen into the TV.

c.If the TV has been exposed to rain or water.

d.If the TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to its normal operation.

e.If the TV has been dropped or damaged in any way.

f.When the TV exhibits a distinct change in perfor- mance-this indicates a need for service.

20.Replacement Parts-When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.

21.Safety Check-Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition.

22.Heat-This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

OPERATING CONTROLS AND FUNCTIONS

- FRONT PANEL -

- REAR PANEL -

ANT.IN

1

2

3

4

5

6

7

8

- REMOTE CONTROL -

7

9

POWER		GAME SLEEP
			DISPLAY
1	2	3
4	5	6	CHANNEL
			RETURN
7	8	9

0 +100

		1.	VIDEO (in) jack- Connect to the video
	14		output jack of a video camera or VCR.
		2.	AUDIO (in) jack- Connect to the audio
	13		output jack of a video camera or VCR.
		3.	EARPHONE jack- To connect an ear-
	12
			phone (not supplied) for personal listening.
			Note: Do not connect earphones that have
	11		an L-shaped plug. The plug may interfere
			with the cabinet.
		4.	MENU button- Press to display the menu
			on the TV screen.
		5.	VOLUME (VOL) ▲/▼ buttons- Press to

6	CH		control the volume level.
VOL	VOL		Press to determine a setting mode from the
5	CH
			menu on the TV screen. (only the VOL ▲
	MUTE	10
			button)
MENU			Press to select or adjust from a particular
4			menu. (for example: Language Selection,
			Channel Presetting, Closed Caption Selection,
			Picture Adjustment, V-CHIP Set Up)
			6. CHANNEL (CH) ▲/▼ buttons- Press to
			select memorized channel.
			Press to select a setting mode from the
			menu on the TV screen.
			Press to select item you want to adjust in
			the picture control mode.
			7. POWER button- Press to turn the TV ON
			and OFF.
			8. Infrared Sensor Window- Receives the
			infrared control signals from the remote
			control unit.

16

15

9.CHANNEL NUMBER buttons- Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel.

+100 button- Press to select cable channels which are equal or greater than number 100.

10.MUTE button- Press the MUTE button to turn off the sound portion of the TV program. (Volume level display turns LIGHT RED from LIGHT BLUE.) Press the MUTE button again or press the VOL(ume) ▲ or ▼ button to restore sound.

11.CHANNEL RETURN button- Press this button to go back to the previously viewed channel. For example, pressing the CHANNEL RETURN button once will change channel display from CH 3 (present channel) to CH 10 (previously viewed channel), and pressing it second time will return from CH 10 to CH 3.

12.DISPLAY button- Press to display the channel number on the screen. If you press it again, the channel number will disappear.

13.SLEEP button- Press the SLEEP button to display the sleep timer and start the function. The shut off time can be determined by the number of times you press the button. (0, 10, 20, 30,..90, 0 minutes)

14.GAME button- Press to set the Game mode and external input mode at the same time. Press the GAME button again to exit the mode.

15.ANT(enna). IN jack- Connect to an antenna, cable system, or satellite system.

16.AC cord- Connect to a standard AC outlet (120V/60Hz).

Note: Remove the AC cord from the hook to avoid breaking a wire before you connect to a standard AC outlet.

INSTALLING THE BATTERIES

1)Slide the battery compartment cover on the remote unit.

2)Insert 2 "AA" penlight batteries into battery compartment in the direction as indicated by the polarity (+ / -) markings. Batteries installed with incorrect polarity may damage the remote unit.

3)Replace the cover.

EXTERNAL INPUT MODE

When using an external input signal (VCR or camcorder), connect the player’s audio/video output cables to the AUDIO IN/ VIDEO IN jacks of your TV. Then press the GAME button. For details, see “USING THE GAME BUTTON” in PICTURE ADJUSTMENT section.

To cancel the sleep timer:

Press the SLEEP button repeatedly until "SLEEP 0" is displayed.

SLEEP 10

PREPARATION FOR USE

LANGUAGE SELECTION

If you want to change the language of the on-screen menu, follow the procedure below.

1)Connect the power cord to a standard AC outlet.

2)Press the POWER button to turn on the TV.

			PICTURE
	3)	Press the MENU button so that the menu display appears on the TV	CHANNEL SET
			[ENG] / ESP / FRA
		screen.
			V-CHIP SET UP
			CAPTION [OFF]
	4)	Press the CH(annel) ▲ or ▼ button to point to "[ENG]".
	5)	Select "ENG(lish)", "ESP(añol)" or "FRA(nçais)" by using	PICTURE
		the VOL(ume) ▲ or ▼ button.	CHANNEL SET
			[ENG] / ESP / FRA
			V-CHIP SET UP
	6)	Press the MENU button to exit the menu.	CAPTION [OFF]

CHANNEL PRESETTING

To preset a channel or to change a preset channel, follow the procedure below.

1)	Press the POWER button to turn on the TV.
2)	Press the MENU button so that the menu display appears	PICTURE
		CHANNEL SET
	on the TV screen.	[ENG] / ESP / FRA
		V-CHIP SET UP
		CAPTION [OFF]
3)	Press the CH(annel) ▲ or ▼ button to point to "CHANNEL SET".	PICTURE
	Then, press the VOL(ume) ▲ button.
		CHANNEL SET
		[ENG] / ESP / FRA
		V-CHIP SET UP
		CAPTION [OFF]
4)	Press the CH(annel) ▲ or ▼ button to point to "AUTO PRESET CH".
	Then, press the VOL(ume) ▲ button.	ADD/DELETE
	The tuner scans and memorizes all active channels in your area.	AUTO PRESET CH

●The TV distinguishes between standard TV channels and cable channels.

●When AUTO PRESET CH action is completed, the lowest memorized channel reappears on the screen.

●When you press the CH(annel) ▲ or ▼ button after selecting "AUTO PRESET CH", the tuner will stop at the memorized channels only.

●The TV may recognize TV channels to be CATV channels by the receiving conditions. In this case, try AUTO PRESET CH action again in the fine receiving conditions.

●When AUTO PRESET CH is activated where there is no TV signal input,"NO TV SIGNALS" will appear on the display after the completion of channel scanning.

[ADD/DELETE FUNCTION]

1)Press the MENU button so that the menu display appears on the TV screen.

2)Press the CH(annel) ▲ or ▼ button to point to "CHANNEL SET". Then, press the VOL(ume) ▲ button.

3)Press the VOL(ume) ▲ button so that "ADD/DELETE" is selected.

4)Use the CH(annel) ▲ or ▼ button to select the

channel you wish to put into memory or to erase from memory.

Note: The menu will disappear in about 10 seconds.

Perform "ADD/DELETE" function while this display appears on the screen.

●Press the VOL(ume) ▲ or ▼ button to light up the channel number in LIGHT BLUE if you wish to add the channel into memory.

●Press the VOL(ume) ▲ or ▼ button to light up the channel number in LIGHT RED if you wish to erase the channel from memory.

PICTURE CHANNEL SET [ENG] / ESP / FRA V-CHIP SET UP CAPTION [OFF]

ADD/DELETE AUTO PRESET CH

5) Press the MENU button to exit the menu.

RESUME FUNCTION

If the power fails or is disconnected while the TV is powered on, the TV will turn on automatically when the power resumes.

OPERATIONS

WATCHING A TV PROGRAM

PICTURE ADJUSTMENT

1)Press the POWER button to turn on the TV.

2)Select the desired channel with the CH(annel) ▲ or ▼ button.

3)Adjust the volume to the desired listening level using the VOL(ume) ▲ or ▼ button.

4)Adjust picture controls for a natural looking image. (See "PICTURE ADJUSTMENT".)

SETTING THE SLEEP TIMER

The sleep timer function enables you to shut off the power without pressing the POWER button after a desired time period.

1)Press the POWER button to turn on the TV and press the SLEEP button on the remote control .

2) You may change the sleep time by pressing the SLEEP button on the remote control repeatedly. The timer can be set up to 90 min-

utes. 10 minutes are added, each time the SLEEP button is pressed. (The timer display counts up and sleep timer will be displayed on the screen when you press the SLEEP button on the remote control.)

Note: When you disconnect the unit from the AC outlet, or when you have a power failure, the sleep time will be lost.

CLOSED CAPTION SELECTION

You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program.

: Press the VOL(ume) ▲ or ▼ button.

1)Press the MENU button so that the menu display appears on the TV screen.

2)Press the CH(annel) ▲ or ▼ button to point to "CAPTION".

3)Press the VOL(ume) ▲ or ▼ button to select the mode you wish.

4)When done, press the MENU button to exit the menu.

PICTURE	PICTURE	PICTURE	PICTURE	PICTURE
CHANNEL SET	CHANNEL SET	CHANNEL SET	CHANNEL SET	CHANNEL SET
[ENG] / ESP / FRA	[ENG] / ESP / FRA	[ENG] / ESP / FRA	[ENG] / ESP / FRA	[ENG] / ESP / FRA
V-CHIP SET UP	V-CHIP SET UP	V-CHIP SET UP	V-CHIP SET UP	V-CHIP SET UP
CAPTION [OFF]	CAPTION [ C1]	CAPTION [ C2]	CAPTION [ T1]	CAPTION [ T2]

1)Press the MENU button so that the menu display appears on the TV screen.

2)Press the VOL(ume) ▲ button so that "PICTURE" is selected.

3)Select the feature you wish to adjust with the CH(annel) ▲ or ▼ button and adjust it with the VOL(ume) ▲ or ▼ button.

GAME MODE

Set to the most suitable position for video games.

[+] : ON

[ - ] : OFF

BRIGHT

Adjust until the whitest parts of the picture are as bright as you prefer.

[+] : increase brightness [ - ] : decrease brightness

CONTRAST

Adjust to increase or decrease contrast. [+] : increase contrast

[ - ] : decrease contrast

COLOR

Adjust to be brilliant or pale color. [+] : be brilliant color

[ - ] : be pale color

TINT

Adjust to obtain natural skin tones. [+] : greenish tone

[ - ] : reddish tone

Notes:

●"+" is achieved by pressing the VOL(ume) ▲ button and "-" by pressing the VOL(ume) ▼ button.

●In the above steps, the picture adjustment display will disappear from the TV screen after about 10 seconds unless you press any buttons, even though you may not be finished. Press the MENU and VOL(ume) ▲ button so that "PICTURE" is selected. Then, press the CH(annel) ▲ or ▼ button repeatedly until the display returns to the screen.

●If you adjust another Picture control after you set the Game mode to [ON], the Game mode is set to [OFF] automatically.

[USING THE GAME BUTTON]

You may also set the Game mode and external input mode at the same time by pressing the GAME button on the remote control. “GAME” appears on the TV screen.

●To exit the Game mode and external input mode, press the GAME button on the remote control again.

●To cancel the Game mode only, adjust the picture control. The Game mode will be set to [OFF] automatically as explained in the previous section. In this case, “VIDEO”(external input mode) instead of “GAME” appears on the TV screen.

●When you press the GAME button if the TV is off, the TV turns on and will be in the Game mode and external input mode automatically.

: Press the CH(annel) ▲ or ▼ button.

[-]

GAME MODE [+]

[-]

BRIGHT

[+]

[-] CONTRAST [+]

[-]

COLOR

[+]

[-]

TINT

[+]

OFF

ON