Fujitsu RX600 S3 User Manual

PRIMERGY RX600 S3
incl. SAS version
System configurator and order-information guide
February 2007
Contents
Instructions Configuration diagram Configurator
0 0 System software 1 I Basic unit
2 II Processor 3 III Memory 4 IV onboard SCSI / SAS Contr
5 V USB devices / optical devices 6 VI Hard disk drives 7 VII Tape Devices 8 VIII optional SCSI / RAID controller 9 IX Fibre Channel controller 10 X Communication / Network 11 XI System Management Products (RemoteView) 12 XII National accessories pack
Change report
PRIMERGY Server
System configurator and order-information guide
PRIMERGY RX600 S3 Status 2007-01-24
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/System-Architect
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/System-Architect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
There are X memory slots which can be equipped with XXX MB
It is permissible to make up to X passes through the memory upgrade options
In one chapter you can only select as many components (here 4x) as the arrow indicates.
Please note that there are information symbols which indicate necessary information.
Further information in the internet see:
http://www.primergy.com
(internet)
http://extranet.fujitsu-siemens.com/primergy
(extranet)
Prices and availability see price list and PC-/System-Architect.
Subject to change and errors excepted.
X times
III
S26361-XXX-XXX S26361-XXX-XXX
Memory XXX MB Memory XXX MB
max. X times per system max. X times per system
Memory, example
4x
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 2 of 17
PRIMERGY RX600 S3 Status 2007-01-24
TOP View
Extension slots
Memory ( III )
SCSI / RAID controller ( VIII )
Fiber Channel ( IX )
Communication/Network ( X )
7654Processors must be plugged
in order according the picture.
3
Processor ( II )
2
1
FRONT VIEW
Accessible drives
Tape drives ( VII )
Operating Panel
5.25"x 0.5" bay for CD/DVD
Local View LCD Display
Hard disk drives ( IV ) hot-plug
SCSI Version: 5x 3.5"SCSI
or
SAS Version: 8x 2.5" SAS
Channel A
Channel B
Hot Plug Redundant Power Supply
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS
Slot
Memory Board A
(2 Banks / 4 modules)
Memory Board B
(2 Banks / 4 modules)
Memory Board C
(2 Banks / 4 modules)
Memory Board D
(2 Banks / 4 modules)
PCI-Express x4 ( hot-plug )
Xeon
Xeon
Xeon
Xeon
Ethern
Ethern
System configurator and order-information guide
Configuration diagram PRIMERGY RX600 S3
System unit ( I )
PCI-X 64-Bit / 100MHz, long
PCI-X 64-Bit / 100MHz, long
PCI-Express x4 ( hot-plug )
occupied by PCIe RAID Controller in SAS Version
PCI-Express x4 ( hot-plug )
PCI-X 64-Bit / 133MHz, long ( hot-plug )
PCI-Express x8 ( hot-plug )
5.25"x1.6" Tape Drive
3.5"x1" SCSI-ID 0
3.5"x1" SCSI-ID 1
3.5"x1" SCSI-ID 2
3.5"x1" SCSI-ID 1
3.5"x1" SCSI-ID 0
MP 3
USB USB
Video USB
MP 4
MP 2
Operating
Panel
MP 1
COM USB
Video USB
Key:
Included in basic unit Option
et
et
1. PSU
2. PSU
REAR VIEW
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 3 of 17
PRIMERGY-Software Configurators and Release Lists
Start "PRIMERGY RX600 S3"
PRIMERGY RX600 S3 Status 2007-01-24
http://extranet.fujitsu-siemens.com/primecluster
http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm
for internal users:
http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm
for partners:
http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm
SW - Configurator 32 bit
with OEM-Software without OEM-Software
for PRIMERGY Server Usage of OEM SW from MS is for PRIMERGY Server
VMware-Software is not allowed to be ordered
- VCMS VirtualCenter Management Server separately.
- Virtual Infrastructure 3 Exception: VMware SW
For all SW products please refer to the corresponding software configurator accessible via the Extranet under Configuration & Tools, -All configurations, -Software, URL see below.
MS - Software: W **) PRIMECLUSTER *)
- Windows Server 2003 R2, - Clustering Standard Edition - Load Balancing Enterprise Edition
- Additional loose Client-Access-Licenses (CALs) Linux - Software: L **) (not for Web Edition) - Open Enterprise Server ***)
CITRIX-Software for - Red Hat EL (OEM): LO Windows: W-MF - Red Hat EL (Support): LS
- Presentation Server LoadBalancing Additional User Licences
not possible under VMware
OEM-SW is bound to HW and
- SuSE Linux ES (OEM): LO
- SuSE Linux ES (Support): LS
MultiPath, Duplex Data Manager (DDM) W2K; W2K3 Linux (W-DDM)
Manageability Software: V Details eg. version numbers are published
- RemoteView Software in the separate SW-Configurator
- RemoteView Service Board
- vPMS 2006std
- Altiris Server Deployment *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
Backup-Software / Application-Software: U **) Pay attention to the release and ordering information in PRINCE -> Operating System
- ARCserve
- openSM2
Find detailed software configurators and release lists (OS-matrix / system management) under following addresses:
Continue with PRIMERGY HW configurator
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 4 of 17
PRIMERGY-Software Configurators and Release Lists
Start "PRIMERGY RX600 S3"
PRIMERGY RX600 S3 Status 2007-01-24
URL see below.
EM64T
- Presentation Server
http://extranet.fujitsu-siemens.com/primecluster
http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm
for internal users:
http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm
for partners:
http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm
SW Configurator EM64T
with OEM-Software without OEM-Software
for PRIMERGY Server Usage of OEM SW from MS is for PRIMERGY Server
VMware-Software is not allowed to be ordered
- VCMS VirtualCenter Management Server separately.
- Virtual Infrastructure 3 Exception: VMware SW
For all SW products please refer to the corresponding software configurator accessible via the Extranet under "Configuration & Tools, -All configurations, -Software,
not possible under VMware
OEM-SW is bound to HW and
only - Windows Server 2003 R2, only - SuSE Linux ES (OEM): LO EM64T Standard x64 Edition x86_64 - SuSE Linux ES (Support): LS
only Windows: W-MF
Microsoft - Software: W Linux - Software *) **)
Enterprise x64 Edition - Red Hat EL (OEM): LO
- Additional loose - Red Hat EL (Support): LS Client-Access-Lizenzen (CALs)
CITRIX-Software for
LoadBalancing Additional User Licences
only MultiPath, Duplex Data Manager (DDM) EM64T Windows, Linux (W-DDM)
Details eg. version numbers are published
Manageability Software: V**) in the separate SW-Configurator
only - RemoteView Software EM64T - RemoteView Service Board
- RemoteView Diagnosis *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
- vPMS 2006std
**) Pay attention to the release and ordering information in PRINCE -> Operating System
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
Continue with PRIMERGY HW configurator
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 5 of 17
System configurator and order-information guide
Start PRIMERGY RX600 S3
PRIMERGY RX600 S3 Status 2007-01-24
Section
PRIMERGY RX600 S3
SCSI
PRIMERGY RX600 S3
SAS
SCSI
basic unit with:
SAS
basic unit with:
- 7 PCI Slots
- 6 PCI Slots
-
3x
PCIe x4 slot (hot plug)
- 2x PCIe x4 slot (hot plug)
Front side
Installation in PRIMERGY 19" Classic rack is not possible.
Rack unit 4U Rack unit 4U
- 3 + 2 bays for 1" HDD`s (two channels) - 8 bays for 2.5" SAS HDD`s - 2 hot-plug fan modules (redundant)
- 1x 64bit / 133MHz PCI-X slot (hot plug) - 1x 64bit / 133MHz PCI-X slot (hot plug) - 1x 5.25" bays FH (1,6" high) for accessible drives
- 2x 64bit / 100MHz PCI-X slot - 2x 64bit / 100MHz PCI-X slot - Rack- mounting kit
I
Basic unit
Basic Unit including:
- 2 hot-plug power supply (redundant)
- LCD-Display for LocalView (Service Display)
- 1 bay (0,5" height) for CD- or DVD-ROM
- 1x PCIe x8 slot (hot plug) - 1x PCIe x8 slot (hot plug) Systemboard with
- onboard RAID 5 functionality - SAS RAID 5 Controller - 1x XEON MP dua core processor with 256MB Cache (BBU optional) with 256MB Cache and BBU (2nd, 3rd and 4th as option)
- memory of basic units selectable via - memory of basic units selectable via - Dual LAN-Controller 1GBit on-board base memory order codes base memory order codes WOL-capable (BroadCom 5704)
2.60GHz/4MB 7110M S26361-K988-V410 2.60GHz/4MB 7110M S26361-K988-V510 - VGA Controller on-board
3.00GHz/4MB 7120M S26361-K988-V420 3.00GHz/4MB 7120M S26361-K988-V520 (ATI Radeon 7000M, 16MB RAM)
3.20GHz/8MB 7130M S26361-K988-V430 3.20GHz/8MB 7130M S26361-K988-V530 - Server Management Controller on-board
3.40GHz/16MB 7140M S26361-K988-V440 3.40GHz/16MB 7140M S26361-K988-V540 (RSB 2 Board optional)
PRIMERGY PRIMECENTER- Rack - Interfaces:
SNP:SY-F1647E301-P 1x VGA (15 pin) Installation ex works for one "Rack-mounting ex factory" server or subsystem. This service is to be ordered once Rear Side Hereby the rack will be delivered per installable server/storage 2x USB 2.0 completely pre-mounted and subsystem, in order to get the 1x VGA (15 pin) all wired connections are tested. server/storage subsystem 1x RS-232-C (serial, 9 pin)
With racks 12U, 24U, 38U: mounted into the PRIMERGY racks. 2x RJ45 (on board LAN) Systems and components In case of the 46 U PRIMERGY rack, no PS/2 connection for KB / Mouse will be delivered installed in the rack this service has to be ordered, (USB connectivity must be used instead) With racks 46U: to get the mounting kits and the Systems and components cables installed will be delivered separately To be ordered only together with a PRIMERGY- Rack Mounting kit is part of the basic unit PRIMERGY RX600 S2 PRIMECENTER rack - 1 pair of telescopic rails (713 - 812mm) e.g.: - 1 bracket DC-PC-Rack S26361-K826-V10x - 1 cable management for DC-PC-racks refer configurator DC-Rack This kit allows for mounting of TX/RX600 S3 in in FSC 19" DataCenter- and max. 1x per System
PRIMECENTER- racks and all server racks conforming to EIA standard EIA-310-D for 19" racks. Therefore the mounting kit is variable in depth from 713 - 812mm
- Intel E8501 chipset with 800MHz Frontside Bus
- 1 memory board (2nd, 3rd and 4th as option)
- Ultra 320 SCSI-controller (LSI 53C1030)
- ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates
3x USB 2.0
A
Due to the heat dissipation of the system, sufficent cooling couldn´t be enabled in classic rack.
Connetion for KVM switch / Rack console
- RC23 can be directly connected (both USB and PS/2 connections)
- KVM S2 series needs the KVM S2 Adapter USB<->VGA
- For ES4/8+ KVM series with PS/2 connector as well as for standard PS/2 KB / Mouse an additional USB to PS/2 adapter must be bought additionally and connected to the RX600 S3. The adapter offers 2x PS/2 ports. Adaper order number, to purchase via PRIMEPOWER, is:
D:GP70P-KA01 Adapter for PS/2<->USB
- Appropriate FSC USB keyboard is S26381-K340-V1* This keyboard also needs USB cable T26139-Y3812-V1
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 6 of 17
System configurator and order-information guide
A
PRIMERGY RX600 S3 Status 2007-01-24
2. CPU
2.60GHz
3.00GHz
3.20GHz
3.40GHz
4MB
4MB
8MB
16MB
3./4. CPU
up to 3
upgrade
2.60GHz
3.00GHz
3.20GHz
3.40GHz
up to
4MB
4MB
8MB
16MB
2x
Section
CPU´s
II
S26361-F3124-E410 S26361-F3124-E420 S26361-F3124-E430 S26361-F3124-E440
Xeon MP 7110M 800 MHz FSB 800 MHz FSB 800 MHz FSB 800 MHz FSB with heat sink and "Easy retention" heat sink and "Easy retention" heat sink and "Easy retention" heat sink and "Easy retention" occupies socket for one CPU occupies socket for one CPU occupies socket for one CPU occupies socket for one CPU max. 1x per system max. 1x per system max. 1x per system max. 1x per system
S26361-F3124-E800
VRM module for 3rd/4th CPU max. 1x per system
S26361-F3124-E410 S26361-F3124-E420 S26361-F3124-E430 S26361-F3124-E440
Xeon MP 7110M 800 MHz FSB 800 MHz FSB 800 MHz FSB 800 MHz FSB with heat sink and "Easy retention" heat sink and "Easy retention" heat sink and "Easy retention" heat sink and "Easy retention" occupies socket for one CPU occupies socket for one CPU occupies socket for one CPU occupies socket for one CPU max. 2x per VRM module max. 2x per VRM module max. 2x per VRM module max. 2x per VRM module
Processor
A 4-way processor system requires a multi-processor operating system Later upgrading to a four-way-processor system is also possible VRM´s for 1st/2nd CPU are on the Motherboard, for the 3nd / 4th CPU addition VRM Modules are required. Extension CPUs must have identical cache size and clock rate
Xeon MP 7120M
TLC on Chip, with
Xeon MP 7120M
TLC on Chip, with
Xeon MP 7130M
TLC on Chip, with
Xeon MP 7130M
TLC on Chip, with
Xeon MP 7140M
TLC on Chip, with
Xeon MP 7140M
TLC on Chip, with
TLC on Chip,
TLC on Chip,
B
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 7 of 17
System configurator and order-information guide
B
PRIMERGY RX600 S3 Status 2007-01-24
No mix of modules within one memory bank is allowed.
RX600 S3 supports the memory protection through Memory Mirroring
or
Memory RAID.
see Note** above
up to 3x
memory
upgrade
boards
Section
S26361-F3072-B622 S26361-F3072-B623 S26361-F3072-B624
Base memory 2 GB Base memory 4 GB Base memory 8 GB DDR RAM PC2-3200 ECC DDR RAM PC2-3200 ECC DDR RAM PC2-3200 ECC
with chipkill support with chipkill support with chipkill support
consisting of 2 modules consisting of 2 modules consisting of 2 modules with 1 GB each with 2 GB each with 4 GB each occupies one bank occupies one bank occupies one bank 1x per base system 1x per base system 1x per base system
III
Memory
The system can be equipped with up 4 memory boards with 2 memory banks each. One Memory Board is allready supplied in the base unit. Each memory board can be equipped with up to 2x 8GB = 16GB memory. The maximal extension is 64GB with 4GB modules!
For each basic unit, one pair of memory modules has to be ordered with the ordercode of "Base Memory" (either 2GB = 2x1GB, 4GB = 2x2GB or 8GB = 2x4GB) Note**: The price of the smallest Base Memory is already included in the basic unit, The price of the other Base Memories is the Delta to the smallest Base Memory Additional memory extensions (Upgrade Memory) can still be configured for the standard market price.
ECC with memory scrubbing function is standard for RX600 S3. Optional hot-spare memory functionality can be configured in the BIOS (redundant memory bank n + 1)
Memory Mirroring requires 2 or 4 Memory boards, Memory RAID requires 4 Memory boards.
S26361-F3072-E622 S26361-F3072-E623 S26361-F3072-E624
Upgrade memory 2 GB Upgrade memory 4 GB Upgrade memory 8 GB DDR RAM PC2-3200 ECC DDR RAM PC2-3200 ECC DDR RAM PC2-3200 ECC
with chipkill support with chipkill support with chipkill support
consisting of 2 modules consisting of 2 modules consisting of 2 modules with 1 GB each with 2 GB each with 4 GB each occupies one bank occupies one bank occupies one bank max. 1x per base system max. 1x per base system max. 1x per base system
S26361-F3125-E130
Memory Board with 2 banks for 2 modules each
max. 3x per system
S26361-F3072-E622 S26361-F3072-E623 S26361-F3072-E624
Upgrade memory 2 GB Upgrade memory 4 GB Upgrade memory 8 GB DDR RAM PC2-3200 ECC DDR RAM PC2-3200 ECC DDR RAM PC2-3200 ECC
with chipkill support with chipkill support with chipkill support
consisting of 2 modules consisting of 2 modules consisting of 2 modules with 1 GB each with 2 GB each with 4 GB each occupies one bank occupies one bank occupies one bank max. 2x per memory board max. 2x per memory board max. 2x per memory board
C
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 8 of 17
System configurator and order-information guide
C
PRIMERGY RX600 S3 SAS Status 2006-12-31
Overview SCSI-cabling of a PRIMERGY RX600 S3 SCSI Base Unit
1x3
1x3
1x3
HDD
HDD
HDD
1x2
HDD
Tape Devices
Tape Devices
Configuration with 1 channels for Disk Drives plus external Tape device
Section
IV
The system is equipped with a two channel Utra 320 onboard SCSI controller including a full featured RAID controller with 256MB Cache (suporting the RAID level 0, 1, 5, 10, 50).
As option the on-board RAID Controller can be equipped with a Battery Backup Unit. This on-board SCSI/RAID controller can be used for the connection of internal tapes and disks drives. Also one channel can be used for the connection of external Tape devices in the SX10 subsystem.
The following rules apply for the cabling:
The cables for the connection of the on-board RAID controller to the disks in the system are includes in the base unit. If an internal tape is configured, an additional SCSI cable is needed. (see section "IV Hard disk drives / Tapes" ) For the connection of external Tape devices to the on board SCSI controller, also an additional cable is needed in the system. (plus cable to connect to the subsystem SX10, see configurator SX10)
S26361-F3128-E20
ROM Battery Backup Unit for on-board RAID controller
max. 1x per system
Picture 1: Picture 2: Picture 3: Two channels for Disks Two ch. for Disks + int. Tape One ch. for Disks + ext. Tape
onboard SCSI / RAID SCSI / RAID SCSI / RAID
on-board SCSI / SAS Controller
SCSI Base Units
onboard
onboard
internal external
optional optional optional
internal Tape Devices
29160 Contr. 29160 Contr. external 29160 Contr. external
Tape Devices Tape Devices
29160 Contr. external 29160 Contr. external 29160 Contr. external
Tape Devices Tape Devices Tape Devices
Configuration with 2 channels for Disk Drives Picture 1
Both channels of the on-board SCSI/RAID-controller are used for SCSI disk drives (pls see pictures above). For the connetion of internal tape devices an additonal SCSI controller is required, pls see section V SCSI-RAID controller
Configuration with 2 channels for Disk Drives plus internal Tape device Picture 2
One channel of the on-board SCSI/RAID-controller is used for SCSI HDD (pls see pictures above). The secound channel can be used to connect additional SCSI HDD and /or an internal tape device.
One channel of the on-board SCSI/RAID-controller is used for SCSI disk drives (pls see pictures above). The secound channel can be used to connect external Tape drives.
D
Picture 3
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 9 of 17
System configurator and order-information guide
D
PRIMERGY RX600 S3 Status 2007-01-24
Overview SAS / SCSI-cabling of a PRIMERGY RX600 S3 SAS Base Unit
8x internal
Tape Devices
2.5" SAS HDD
SAS Base Units
AB. on-board SCSI-/ SAS RAID-Controller for accessible drives and SAS HDD´s -> SAS Version
The system will be delivered with a 8-port SAS RAID controller for the connection of SAS HDD´s
This SAS RAID Controller is equipped with 256MB Cache and BBU (suporting the RAID level 0, 1, 5, 10, 50), and can be used only for the connection of internal disks drives.
Additonally the system is equipped with a two channel Utra 320 onboard SCSI controller
This on-board SCSI controller can be used for the connection of internal or external tape devices.
The following rules apply for the cabling:
The cables for the connection of the SAS RAID controller to the disks in the system are includes in the base unit. If an internal tape is configured, an additional SCSI cable is needed. (see section "IV Hard disk drives / Tapes" ) For the connection of external Tape devices to the on board SCSI controller, also an additional cable is needed in the system. (plus cable to connect to the subsystem SX10, see configurator SX10)
Eight SAS ports for Disks Two SCSI ports for int./ext. Tape
integrated SAS RAID controller external
optional
onboard SCSI contr.
internal
29160 Contr. Tape Devices
29160 Contr. external
Tape Devices
external SCSI Interface
S26361-F3128-E102
external SCSI interface plug: 1x VHDCI / UHD68(S) max. 1x per system
E
internal
Tape Devices
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 10 of 17
System configurator and order-information guide
E
PRIMERGY RX600 S3 Status 2007-01-24
USB
must be used
1x
max. 5
max. 8
Section
S26361-F3123-E1 S26361-F3236-E1
CD-RW / DVD drive 0.5" DVD-RW 8x super multi drive 24/24/24x / 8x ATAPI all formats, DUAL/DL, DVD-RAM CD-RW only with W2K, W3K, Linux only W2K, W3K and Linux
0.5 x 5.25", anthracite bezel 0.5 x 5.25", anthracite bezel max. 1x per system max. 1x per system
Section
V
VI
S26361-F3121-E173 S26361-F3121-E114 S26361-F3121-E130
Hard disk 73GB Hard disk 146GB Hard disk 300GB 10000rpm,<5,5ms, 8MB Cache 10000rpm,<5,5ms, 8MB Cache 10000rpm,<5,5ms, 8MB Cache
Ultra 320 SCSI (320MB/s) Ultra 320 SCSI (320MB/s) Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pins) Interface: Wide SCA (80-pins) Interface: Wide SCA (80-pins) hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray occupies 1" bay occupies 1" bay occupies 1" bay SCSI/RAID controller necessary SCSI/RAID controller necessary SCSI/RAID controller necessary max. 5x per system max. 5x per system max. 5x per system
USB devices / optical devices
One of the following process if no automized (e.g. Serverstart / Altiris / RIS / ADS / …) installation is done:
1) USB DVD+-RW: Traveller III DVD DL super multi drive
2) FDD USB (external): external USB FDD
3) USB Keyboard: KBPC PX D, professional keyboard
4) USB Mouse: Optical Wheel Mouse
5) USB Memorybird: S26391-F6046-L24
Memorybird 1GB Additionally a monitor can be connected to the VGA 15-pin interface.
Hard disk drives
HDD´s for SCSI Base Units
devices
for integrating the drivers during installation
S26391-F3152-L300
(USB cable included)
S26391-F264-L226
(USB cable included)
S26381-K340-V120
S26381-K403-L100
S26361-F3121-E536 S26361-F3121-E573 S26361-F3121-E514
Hard disk 36GB Hard disk 73GB Hard disk 146GB
15.000rpm,<4ms, 8MB Cache 15.000rpm,<4ms, 8MB Cache 15.000rpm,<4ms, 8MB Cache
Ultra 320 SCSI (320MB/s) Ultra 320 SCSI (320MB/s) Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pins) Interface: Wide SCA (80-pins) Interface: Wide SCA (80-pins) hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray occupies 1" bay occupies 1" bay occupies 1" bay SCSI/ RAID controller necessary SCSI/ RAID controller necessary SCSI/ RAID controller necessary max. 5x per system max. 5x per system max. 5x per system
HDD´s for SAS Base Units
S26361-F3208-E136 S26361-F3208-E173
HD 36GB 10krpm 2.5" HD 73GB 10krpm 2.5" 10000rpm,<4,5ms, 8MB Cache 10000rpm,<4,5ms, 8MB Cache
SAS 3Gb/s SAS 3Gb/s
hot plug/hot replace tray hot plug/hot replace tray max. 8x per base unit max. 8x per base unit
F
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 11 of 17
System configurator and order-information guide
F
PRIMERGY RX600 S3 Status 2007-01-24
S26361-F2848-E31
1x
Section
VII
S26361-F3128-E101
internal SCSI-Cable for connetion of internal Tape devices max. 1x per system
S26361-F2848-E3 S26361-F2849-E3 S26361-F3224-E3
Tape drive DDS Gen5 Tape drive VXA-2 Tape drive VXA-320
DDS-G5 for One buttom dis. recov. Connector: HD68 Connector: HD68 36GB, 3MB/s, U2W SCSI without cable without cable Connector: HD68 incl. description (Ger/US) incl. description (Ger/US) without cable data and cleaning cartridge data and cleaning cartridge incl. description (Ger/US) data and cleaning cartridge max. 1x per system max. 1x per system
1.6 * 5.25", anthracite bezel max. 1x per system
Tapes devices
(only for OBDR)
80GB, 6MB/s, U2W SCSI 160GB, 12MB/s, U160 SCSI
1.6 * 5.25", anthracite bezel 1.6 * 5.25", anthracite bezel
S26361-F3157-E3 S26361-F3459-E3
Tape drive LTO2HH Ultrium Tape drive LTO3HH Ultrium 200GB, 24MB/s, U160 SCSI 400GB, 60MB/s, U320 SCSI Connector: HD68 Connector: HD68 without cable without cable incl. description (Ger/US) incl. description (Ger/US) data and cleaning cartridge data and cleaning cartridge
1.6 * 5.25", anthracite bezel 1.6 * 5.25", anthracite bezel max. 1x per system max. 1x per system
as soon as available
(only in SAS Base Units)
LTO 3HH can be can be installed only in SAS version
G
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 12 of 17
System configurator and order-information guide
G
PRIMERGY RX600 S3 Status 2007-01-24
B. SCSI - controller for internal and external devices.
max. 2x
the connection of external subsystems (SX30)
C. RAID-Controller for external Disk Arrays
max. 2x
SAS RAID controller for JBOD subsystems
It is only a maximum cable
length of 2m supported
Controller plus optional BBU
require a full hight PCI slot.
Section
VIII
S26361-F2399-E1
1-channel SCSI U160 Controller Adaptec 29160 plug: internal: HD 50-pin & HD68 external: HD68 without cable 64/66 PCI
3.3V and 5V tolerant signaling max. 2x per system
S26361-F3006-E128
2-channel RAID Controller U320 LSI 320-2 128MB SDRAM ECC Cache default with TBBU plug: internal 2x HD68; external: 2x VHDCI without cable 64/66 PCI controller, 180mm
3.3V and 5V tolerant signaling max. 2x per system
optional SCSI / RAID controller
The RAID controller can be used only for
Cables for the connection from the RAID Controllers to the subsystem see configurator SX30.
S26361-F3215-E1
8 port SAS RAID Controller LSI MegaRAID SAS 8344 ELP 256MB Cache with ECC optional BBU SAS 3Gb/sec 4 internal / 4 port external PCIe x4, 198mm full height bracket max. 1x per system
S26361-F3215-E10
Cache Battery Backup Unit max. 1x per Controller
H
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 13 of 17
System configurator and order-information guide
H
PRIMERGY RX600 S3 Status 2007-01-24
Qlogic controller
Emulex Controller
max. 3x or
max. 3x / 4x
Section
Qlogic controller
Emulex controller
IX
S26361-F3097-E1
2GBit/s FC Controller possible Qlogic QLA2340, full height bracket 1 channel 2GBit/sec FC Controller LC Interface for 50µm Fiber PCI-X 64Bit / 133MHz, 170mm
3.3V / 5V tolerant signaling max. 3x per system
Fibre channel controller
In SAS version max. 3x PCIe controller can be installed
S26361-F3306-E1 S26361-F3306-E2
4GBit/s FC Controller 4GBit/s FC Controller Emulex Emulex LPe1150, full height bracket LPe11002, full height bracket 1 channel 4GBit/sec FC Controller 2 channel 4GBit/sec FC Controller LC Interface for 50µm Fiber LC Interface for 50µm Fiber PCIe x4, 170mm PCIe x4, 170mm max. 3x / 4x per system max. 3x / 4x per system
No mix and match for Qlogic and Emulex Fibre channel controllers
All controllers for the connection of external storage systems are delivered without cables. For the configuration of external cabling see the configurator for external storage systems.
For Fibre Channel SAN also other componets like switches, SFPs and optical wires are orderable (for details see price liste)
I
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 14 of 17
I
PRIMERGY RX600 S3 Status 2007-01-24
A) Single Port LAN Adapter PCI-X
3x
C) Single Port LAN Adapter PCIe
3x / 4x
System configurator and order-information guide
Section
X
on-board LAN Controller
Dual Gbit Ethernet Contr. on-board The Intel LAN Controllers Pro 1000MT, 1000MF, 1000PT, 1000PF BroadCom BCM5704 can be used with the on-board controller in Teaming Mode
ext: 2 x RJ 45 connector for the teaming the Broadcom driver.
S26361-F3054-E1 S26361-F3053-E1
Gigabit Ethernet Contr. 1000SX Gigabit Ethernet Controller 1000TX Eth. Ctrl 1x1Gbit PCI-X Pro/1000MF LC Eth Ctrl 1x1Gbit PCI-X Pro/1000MT Cu Intel PRO/1000 MF Server Adapter Intel PRO/1000 MT Server Adapter PCI-X (PCI64/133), min 165 mm PCI-X (PCI64/133) ext:LC-connector ext: for RJ45-connector, Cat 5 max. 3x per system max. 3x per system
B) Dual Port LAN Adapter PCI-X
S26361-F3011-E1
Gigabit Ethernet Controller Dual 1000TX Eth Ctrl 2x1Gbit PCI-X PRO/1000MT Cu Intel Pro/1000MT Dual Port Server Ad. PCI-X (PCI64/133) ext: for RJ45-plug, Cat 5 max. 1x per system
Communication / Network
Teaming: Failover, Load Balancing
With Broadcom on-board adapters for Gigabit Ethernet must be used
Two onboard LAN ports can likewise educate a team.
S26361-F3241-E1 S26361-F3242-E1
Gigabit Ethernet Contr. 1000SX Gigabit Ethernet Controller 1000TX Eth. Ctrl 1x1Gbit PCIe Pro/1000PT Eth. Ctrl 1x1Gbit PCIe Pro/1000PF Intel PRO/1000 MPT Server Adapter Intel PRO/1000 PF Server Adapter PCIe x1 PCIe x4 ext:LC-connector ext: for RJ45-connector, Cat 5 max. 3x / 4x per system max. 3x / 4x per system
D) Dual Port LAN Adapter PCIe x4 can be installed
while stocks last
S26361-F3143-E1 S26361-F3228-E1
Gigabit Ethernet Contr. dual 1000TX Gigabit Ethernet Controller Dual 1000TX Eth. Ctrl 2x1Gbit PCIe PRO/1000P Cu Eth Ctrl 2x1Gbit PCIe PRO/1000PT Cu Intel Pro/1000P dual Server Adapter Intel Pro/1000PT dual Server Adapter PCIe x4, 170mm PCIe x4 ext: for RJ45-plug, Cat 5 ext: for RJ45-plug, Cat 5 connection with Cat 5 cabling max. 3x / 4x per system SW: VLAN, Fast & Gbit Etherchannel max. 3x / 4x per system
J
In SAS version max. 3x PCIe controller
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 15 of 17
J
PRIMERGY RX600 S3 Status 2007-01-24
standard
System configurator and order-information guide
Section
Section
XI
S26361-F1790-E221 S26361-F2425-E103 RemoteView Software V5.0 RSB S2 LP 3HU
Installation and configuration of RemoteView Web and LAN FrontEnd RSB, BMC-Manager, RTDS, FreeDOS and online manuals
XII
System Management Products (RemoteView)
RemoteView Service Board S2 Low Profile Version with 3 U bracket for one incl. cables and RV SW max. 1x per system
S26361-F2425-E305 RSB S2 LP external power supply
RemoteView Service Board S2 Low Profile external power supply including power cable with Euro- and Euro socket connector
National accessories packs
System will be shipped with two power cords ICE320 C14->C13 for rack installation. Country specific power cords are not required.
PCI-slot
End PRIMERGY RX600 S3
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 16 of 17
System configurator and order-information guide
Change Report
Date
Order number
Changes
2007-01-24
2007-01-24
2006-12-19
S26361-K988-V510-540
2006-12-14
S26361-K988-V5xx
SAS Base Units added
2006-11-28
Singel Port PCIe LAN controller - now available
2006-11-15
2006-11-15
PRIMERGY RX600 S3 Status 2007-01-24
S26361-F3124-E200 VRM module for 3rd/4th CPU - no longer available
2007-01-24 S26361-K988-V122 Rack mountable server 19" (4U) with processor Xeon 3.66GHz / 1MB SLC - no longer available 2007-01-16 S26361-F3215-E10 Cache Battery Backup Unit for 8 port SAS RAID Controller - now available 2007-01-16 S26361-F3215-E1 8 port SAS RAID Controller - now available
2006-11-15 S26361-F3124-E282 Processor Xeon MP 7030 2.80GHz 2x1MB - no longer available 2006-11-15 S26361-F3124-E304 Processor Xeon MP 7041 3.00GHz 2x1MB - no longer available 2006-11-15 S26361-K988-V112 Rack mountable server 19" (4U) with processor Xeon MP 3.16GHz 1MB - no longer available 2006-11-15 S26361-K988-V312 Rack mountable server 19" (4U) with processor Xeon MP 7020 3.16GHz 2x1MB - no longer available 2006-11-15 S26361-K988-V322 Rack mountable server 19" (4U) with processor Xeon MP 7030 2.80GHz 2x1MB - no longer available 2006-11-15 S26361-K988-V332 Rack mountable server 19" (4U) with processor Xeon MP 7041 3.00GHz 2x1MB - no longer available 2006-08-25 S26361-F3124-E440 Processor Xeon MP 7140M 3.40GHz 16MB 800MHz - now available 2006-08-25 S26361-F3124-E430 Processor Xeon MP 7130M 3.40GHz 8MB 800MHz - now available 2006-08-25 S26361-F3124-E420 Processor Xeon MP 7120M 3.00GHz 4MB 800MHz - now available 2006-08-25 S26361-F3124-E410 Processor Xeon MP 7110M 2.60GHz 4MB 800MHz - now available 2006-08-25 S26361-F3128-E800 VRM module for 3rd/4th CPU - now available 2006-08-25 S26361-K988-V440 Rack mountable server 19" (4U) with 64-bit Xeon MP Dual Core processor 7140; 16MB TLC - now available 2006-08-25 S26361-K988-V430 Rack mountable server 19" (4U) with 64-bit Xeon MP Dual Core processor 7130; 8MB TLC - now available 2006-08-25 S26361-K988-V420 Rack mountable server 19" (4U) with 64-bit Xeon MP Dual Core processor 7120; 4MB TLC - now available 2006-08-25 S26361-K988-V410 Rack mountable server 19" (4U) with 64-bit Xeon MP Dual Core processor 7110; 4MB TLC - now available 2006-02-13 first draft
S26361-F3124-E361 Processor Xeon MP 3.66GHz 1MB - no longer available
Rack mountable server 19" (4U) SAS basic unit - now available
S26361-F3241x-E1 S26361-F3124-E311 Processor Xeon MP 3.16GHz 1MB - no longer available S26361-F3124-E262 Processor Xeon MP 7020 3.16GHz 2x1MB - no longer available
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 17 of 17
Loading...