The BIOS Setup Utility is a program that sets up the operating environment for your notebook. Your
BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change
the BIOS environment to operate your notebook.
The BIOS Setup Utility configures:
• Device control feature parameters, such as changing I/O addresses and boot devices.
• System Data Security feature parameters, such as passwords.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following:
1. Turn on or restart your notebook.
2. Press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of
the BIOS Setup Utility with the current settings displayed.
3. Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to
review or alter the current settings.
Navigating Through The Setup Utility
The BIOS setup utility consists of seven menus; Main, Advanced, Security, Power, Boot, Info and
Exit. This document explains each menu, including all submenus and setup items.
The following procedures allow you to navigate the setup utility menus:
1. To select a menu, use the cursor keys: [←] , [→].
2. To select a field within a menu or a submenu, use the cursor keys: [ ↑], [ ↓].
Critical Point
Selecting a field causes a help message about that field to be displayed on the right-hand
side of the screen.
Pressing the Enter key with the highlight on a selection that is not a submenu or auto selection
will cause a list of all options for that item to be displayed. Pressing the Enter key again will
select the highlighted choice.
2
3. To select the different values for each field, press the [Spacebar] or [+] to change to the next
higher selection and [F5] or [-] to go to the next lower selection.
4. To activate a submenu press [Enter].
5. To return to a menu from a submenu, press [Esc].
6. To go to Exit menu from another menu, press [Esc].
7. Pressing the [F9] key resets all items in the BIOS to the default values.
8. Pressing the [F10] key saves the current configuration and exits the BIOS Setup Utility. You will
be asked to verify this selection before it is executed.
9. Pressing the [F1] key gives you a general help screen.
Entering the Setup Utility After a Configuration Change or System Failure
If there has been a change in system configuration that does not match the parameter settings
stored in your BIOS memory, or there is a failure in the system, the system beeps and/or displays an
error message after the Power On Self Test (POST). If the failure is not severe, it will give you the
opportunity to modify the settings of the setup utility, as described in the following steps:
1. When you turn on or restart the computer there is a beep and/or the following message appears
on the screen:
Error message - please run SETUP program Press <F1> key to continue,
<F2> to run SETUP
2. If an error message is displayed on the screen, and you want to continue with the boot process
and start the operating system anyway, press the [F1] key.
Critical Point
If your settings require it, you may be asked for a password before the operating system will
be loaded.
3. If an error message is displayed on the screen, and you want to enter the setup utility, press the
[F2] key.
4. When the setup utility starts with a fault present, the system displays the following message:
Warning!
Error message
[Continue]
5. Press any key to enter the setup utility. The system will then display the Main Menu with current
parameters values.
3
MAIN MENU
SETTING STANDARD SYSTEM PARAMETERS
The Main Menu allows you to set or view the current system parameters. Follow the instructions for
Navigating Through the Setup Utility to make any changes.
The following tables show the names of the menu fields for the Main menu and its submenus, all of
the options for each field, the default settings and a description of the field’s function and any special
information needed to help understand the field’s use.
Critical Point
System Time and System Date can also be set from your operating system without using the
setup utility. Use the calendar and time icon on your Windows Control Panel.
Figure 1. Main Menu
4
Menu Field
System Time:
System Date:
Primary Master:
Secondary
Master:
Language:
Table 1: Fields, Options and Defaults for the Advanced Menu
Options
—
—
Selects Primary
Master submenu
Selects
Secondary
Master submenu
• English (US)
• Japanese (JP)
Default
—
—
[Toshiba
MK2018GAP(PM)]
[Toshiba DVDROM SD-R2102(SM)]
English (US)]
Description
Sets and displays the current time.
Time is in a 24 hour format of
hours:minutes:seconds with 2 digits
for each. (HH:MM:SS). Example:
16:45:57. You may change each
segment of the time separately.
Move between the segments with
the [Tab ] key and/or [Shift] + [Tab ]
keys.
Sets and displays the current date.
Date is in a month/day/year numeric
format with 2 digits each for month
and day and 4 digits for year. (MM/
DD/YYYY) for example: 03/20/1998.
You may change each segment of
the date separately. Move between
the segments with the [Tab ] key and/
or [Shift] + [Tab] keys.
Displays the type of device on this
ATA/ATAPI interface, if there is one.
Pressing the Enter key selects the
Primary Master submenu allowing
additional device configuration
options for this interface.
Displays the type of device on this
ATA/ATAPI interface, if there is one.
Pressing the Enter key selects the
Secondary Master submenu
allowing additional device
configuration options for this
interface.
The default setting differs between
the US/European and the Japanese
model. Selects the display language
for the BIOS.
5
Primary Master Submenu of the Main Menu
The Primary Master submenu identifies which ATA devices are installed.
Note:
Actual hard drive label shown may vary. Depending on the drive type, information such as cylinders,
heads and sectors may also be displayed.
Figure 2. Primary Master Submenu
6
Table 2: Fields, Options and Defaults for the Primary Master Submenu of the Main Menu
Menu Field
Ty p e:
Cylinders:
Heads:
Sectors:
Maximum
Capacity:
Multi-Sector
Transfers:
Options
• Auto
• None
• Hard Disk
• CD-ROM
• A number
between 0 and
65,535
• A number
between 1 and
16
• A number
between 0 and
63
• Display only
• Disabled
• 2 Sectors
• 4 Sectors
• 8 Sectors
• 16 Sectors
• 32 Sectors
• 64 Sectors
• 128 Sectors
Default
[Auto]
—
—
—
—
[16 Sectors]
Description
Selects the ATA/ATAPI device type.
Select Auto to have the type
automatically identified by the BIOS
at POST. If None is selected, all of
the following Set-up items do not
appear. If Hard Disk is selected, you
must specify the number of Cylinders, Heads, and Sectors for the
drive. Select CD-ROM to select
parameters for CD-ROM drive.
This item appears only when the
type is identifed as Hard Disk. When
Hard Disk is selected, you can
change the value. This field is
changed by incrementing (pressing
the [Spacebar]) or by typing in the
number.
This item appears only when the
type is identifed as Auto or Hard
Disk. When Hard Disk is selected,
you can change the value. This field
is changed by incrementing
(pressing the [Spacebar]) or by
typing in the number.
This item appears only when the
type is identifed as Auto or Hard
Disk. When Hard Disk is selected,
you can change the value. This field
is changed by incrementing
(pressing the [Spacebar]) or by
typing in the number.
Displays the maximum capacity of
the drive calculated from the
parameters of the hard disk when
Hard Disk is selected.
This option cannot be changed
when Auto is selected. Specify the
number of sectors per block for
multiple sector transfer.
7
Table 2: Fields, Options and Defaults for the Primary Master Submenu of the Main Menu
Menu Field
LBA Mode
Control:
PIO Transfer
Mode:
DMA Transfer
Mode:
Options
• Disabled
• Enabled
• Standard
• Fast PIO 1
• Fast PIO 2
• Fast PIO 3
• Fast PIO 4
• Disabled
• Multiword
DMA 1
• Multiword
DMA 2
• Ultra DMA 0
• Ultra DMA 1
• Ultra DMA 2
• Ultra DMA 3
• Ultra DMA 4
Default
[Enabled]
[Fast PI0 4]
[Ultra DMA 4]
Description
Enables or disables logical Block
Addressing in place of Cylinder,
Head, Sector addressing. This
option cannot be changed when
Auto is selected.
Selects the method for moving data
to/from the drive. Autotype the drive
to select the optimum transfer mode.
This option cannot be changed
when Auto is selected. Multi-word
DMA is automati-cally set to mode 1
for Fast PIO 1, Fast PIO 2, Fast PIO
3, and set to mode 2 for Fast PIO 4 /
DMA.
Selects the method for moving data
to/from the drive. Autotype the drive
to select the optimum transfer mode.
This option cannot be changed
when Auto is selected.
8
Secondary Master Submenu of the Main Menu
The Secondary Master submenu identifies which ATA devices are installed.
Note:
Actual drive label shown may vary. Depending on the drive type, information such as cylinders,
heads and sectors may also be displayed.
Figure 3. Secondary Master Submenu
9
Table 3: Fields, Options and Defaults for the Secondary Master Submenu of the Main Menu
Menu Field
Ty p e:
Cylinders:
Heads:
Sectors:
Maximum
Capacity:
Multi-Sector
Transfers:
Options
• Auto
• None
• Hard Disk
• CD-ROM
• A number
between 0 and
65,535
• A number
between 1 and
16
• A number
between 0 and
63
• Display only
• Disabled
• 2 Sectors
• 4 Sectors
• 8 Sectors
• 16 Sectors
• 32 Sectors
• 64 Sectors
• 128 Sectors
Default
[Auto]
—
—
—
—
[Disabled]
Description
Selects the ATA/ATAPI device type.
Select Auto to have the type
automatically identified by the BIOS
at POST. If None is selected, all of
the following Set-up items do not
appear. If Hard Disk is selected, you
must specify the number of Cylinders, Heads, and Sectors for the
drive. Select CD-ROM to select
parameters for CD-ROM drive.
This item appears only when the
type is identifed as Hard Disk. When
Hard Disk is selected, you can
change the value. This field is
changed by incrementing (pressing
the [Spacebar]) or by typing in the
number.
This item appears only when the
type is identifed as Auto or Hard
Disk. When Hard Disk is selected,
you can change the value. This field
is changed by incrementing
(pressing the [Spacebar]) or by
typing in the number.
This item appears only when the
type is identifed as Auto or Hard
Disk. When Hard Disk is selected,
you can change the value. This field
is changed by incrementing
(pressing the [Spacebar]) or by
typing in the number.
Displays the maximum capacity of
the drive calculated from the
parameters of the hard disk when
Hard Disk is selected.
This option cannot be changed
when Auto is selected. Specify the
number of sectors per block for
multiple sector transfer.
10
Table 3: Fields, Options and Defaults for the Secondary Master Submenu of the Main Menu
Menu Field
LBA Mode
Control:
PIO Transfer
Mode:
DMA Transfer
Mode:
Options
• Disabled
• Enabled
• Standard
• Fast PIO 1
• Fast PIO 2
• Fast PIO 3
• Fast PIO 4
• Disabled
• Multiword
DMA 1
• Multiword
DMA 2
• Ultra DMA 0
• Ultra DMA 1
• Ultra DMA 2
• Ultra DMA 3
• Ultra DMA 4
Default
[Disabled]
[Disabled]
[Disabled]
Description
Enables or disables logical Block
Addressing in place of Cylinder,
Head, Sector addressing. This
option cannot be changed when
Auto is selected.
Selects the method for moving data
to/from the drive. Autotype the drive
to select the optimum transfer mode.
This option cannot be changed
when Auto is selected. Multi-word
DMA is automatically set to mode 1
for Fast PIO 1, Fast PIO 2, Fast PIO
3, and set to mode 2 for Fast PIO 4 /
DMA.
Selects the method for moving data
to/from the drive. Autotype the drive
to select the optimum transfer mode.
This option cannot be changed
when Auto is selected.
11
ADVANCED MENU
SETTING DEVICE FEATURE CONTROLS
The Advanced Menu allows you to:
• Enable or disable support for Plug & Play operating systems.
• Select between the display panel and an external CRT display.
• Enable or disable compensation for your display.
• Configure PCI devices in your system.
• Configure CPU and USB features.
Follow the instructions for Navigating Through the Setup Utility to make any changes.
The following tables show the names of the menu fields for the Advanced Menu and its submenus, all
of the options for each field, the default settings and a description of the field’s function and any
special information needed to help understand the field’s use.
12
Figure 4. Advanced Menu
Loading...
+ 25 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.