Fujitsu MDG3064UB, MDG3130UB User Manual
MDG3064UB, MDG3130UB
OPTICAL DISK DRIVES
MAINTENANCE MANUAL
C156-F046-01EN
FOR SAFE OPERATION
Handling of This Manual
This manual contains important information for using this product. Read thoroughly before using
the product. Use this product only after thoroughly reading and understanding especially the
section "Important Alert Items" in this manual. Keep this manual handy, and keep it carefully.
FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering
damage to their property. Use the product according to this manual.
This product is designed and manufactured for use in standard appl ic ations such as off ice work,
personal devices and household appliances. This product is not intended for special uses (atomic
controls, aeronautic or space systems, mass transport vehicle operating controls, medical devices for
life support, or weapons firing controls) where particularly high reliability requirements exist,
where the pertinent levels of safety are not guaranteed, or where a failure or operational error could
threaten a life or cause a physical injury (hereafter referred to as "mission-critical" use). Customers
considering the use of these products for miss ion-c rit ica l appl ica tio ns mus t have safe ty-ass u ran ce
measures in place beforehand. Moreover, they are requested to consult our sales representative
before embarking on such specialized use.
First Edition October 2001
The contents of this manual may be revised without prior notice.
The contents of this manual shall not be disclosed in any way or reproduced in any media without
the express written permission of Fujitsu Limited.
All Rights Reserved, Copyright FUJITSU LIMITED 2001
Revision History
(1/1)
Edition Date
01 2001.10.5 — —
Revised section (*1)
(Added/Deleted/Altered)
Details
*1 Section(s) with asterisk (*) refer to the previous edition when those were deleted.
C156-F046-01EN
This page is intentionally left blank.
This document describes procedures for maintenance of the MDG3064UB/MDG3130UB
(DynaMO 640U2/1300U2), a 3.5-inch magneto-optical disk drive. The
MDG3064UB/MDG3130UB (referred to as "the product" hereafter) is provided with the
MCM3064UB/MCM3130UB 3.5-inch magneto-optical disk drive unit (referred to as "MO
drive" hereafter). The components are built in a case designed specifically for the product.
Refer to related manuals for operations other than maintenance and for explanation about
an MO drive.
The organization of this manual, related reference manual and conventions for alert
messages follow.
Overview of Manual
This manual consists of the following six chapters, glossary, and abbreviation:
Chapter 1 Overview
This chapter introduces the MDG3064UB/MDG3130UB MO disk drive. The chapter
describes the system features and outline of maintenance.
Preface
Chapter 2 Diagnosis and Maintenance
This chapter describes maintenance conditions, diagnosis methods, failure analysis
procedures, and system updating procedures of the MDG3064UB/MDG3130UB MO disk
drive.
Chapter 3 Troubleshooting
This chapter describes troubleshooting of a system connected to a Macintosh G3 and
Windows computer.
Chapter 4 Returning Repaired Unit
This section describes procedures for unpacking, packing, transporting, and storing the
MDG3064UB/MDG3130UB MO disk drive.
Chapter 5 Cleaning
C156-F046-01EN i
Preface
CONVENTIONS USED IN THIS MANUAL
Conventions for Alert Messages
This manual uses the following conventions to show the alert messages. An alert message
consists of an alert signal and alert statements. The alert signal consists of an alert symbol
and a signal word or just a signal word.
The following are the alert signals and their meanings:
This indicates a hazardous situation
serious personal injury
procedure correctly.
This indicates a hazardous situation
personal injury
correctly.
This indicates a hazardous situation
or
moderate personal injury
the procedure correctly. This alert signal also indicates
that damages to the product or other property,
the user does not perform the product correctly.
This indicates information that could help the user use the
product more efficiently.
In the text, the alert signal is centered, followed below by the indented message. A wider
line space precedes and follows the alert message to show where the alert message begins
and ends. The following is an example:
if the user does not perform the procedure
if the user does not perform the
if the user does not perform
likely
could
could
to result in
result in
result in
occur if
may
serious
minor
ii C156-F046-01EN
Attention
Preface
(Example)
IMPORTANT
Fujitsu issues a Change Request/Notification regarding post-factory-shipment revision
number changes. When the user changes the version number, the revision-number label
should be updated as described above after the change is applied.The main alert messages
in the text are also listed in the “Important Alert Items.”
Please forward any comments you may have regarding this manual.
To make this manual easier for users to understand, opinions from readers are needed.
Please write your opinions or requests on the Comment at the back of this manual and
forward it to the address described in the sheet.
C156-F046-01EN iii
This page is intentionally left blank.
Important Alert Items
Important Alert Messages
The important alert messages in this manual are as follows:
A hazardous situation could result in minor or moderate personal injury if the
user does not perform the procedure correctly. Also, damage to the product
or other property, may occur if the user does not perform the procedure
correctly.
Task Alert message Page
Normal Operation When cleaning the drive, do not use a toxic cleaning agent. 5-1
Normal Operation In case of contact, immediately flush eyes with water. 5-7
C156-F046-01EN v
This page is intentionally left blank.
MANUAL ORGANIZATION
MDG3064UB, MDG3130UB
OPTICAL DISK DRIVES
MAINTENANCE MANUAL
(C156-F046)
<This manual>
MCE3130UB, MCF3064UB
OPTICAL DISK DRIVES
PRODUCT MAN UA L
(C156-E222)
1. OVERVIEW
2. DIAGNOSIS AND MAINTENANCE
3. TROUBLESHOOTING
4. RETURNING REPAIRED UNIT
5. CLEANING
1. GENERAL DESCRIPTION
2. SPECIFICATIONS
3. INSTALLATION REQUIREMENTS
4. HOST INTERFACE
5. OPERATION AND CLEANING
6. DIAGNOSTICS AND MAINTENANCE
C156-F046-01EN vii
REFERENCED STANDARDS
The product specifications and functions described in this manual conform to the following
standards:
Specification
(document) number
Universal Serial Bus Specification, Revision 1.1 USB implementers Forum
Universal Serial Bus Mass Storage Class Bulk-Only
Transport, Revision 1.0
Universal Serial Bus Mass Storage Class
Specification Overview, Revision 1.0
ISO/IEC 10090
ISO/IEC 13963
ISO/IEC 15041
Cherry Book Version
1.0
*1
ISO= International Organization for Standardization
IEC= International Electrical for Commission
JTC1= Joint Technical Committee 1
90mm Optical Disk Cartridges, rewritable and read
only, for data interchange.
Data Interchange on 90mm Optical Disk cartridges
Capacity: 230 megabytes per cartridge.
Data Interchange on 90mm Optical Disk Cartridges
Capacity: 640 megabytes per cartridge.
GIGAMO 1.3GB 90mm Magneto-Optical Disk
System.
Name Concerned organization
USB implementers Forum
USB implementers Forum
ISO/IEC (*1)
ISO/IEC (*1)
ISO/IEC JTC1 (*1)
FUJITSU LIMITED SONY
CORPORATION
viii C156-F046-01EN
Contents
CHAPTER 1 OVERVIEW ................................................................................ 1-1
1.1 Description 1-1
1.2 Maintenance Method 1-1
CHAPTER 2 DIAGNOSIS AND MAINTENANCE............................................ 2-1
2.1 Maintenance Conditions 2-1
2.2 Diagnosis 2-2
2.3 Troubleshooting Method 2-2
2.4 Unit Version Number 2-3
CHAPTER 3 TROUBLESHOOTING ............................................................... 3-1
3.1 For Macintosh Users 3-1
3.2 For Windows Users 3-2
CHAPTER 4 RETURNING REPAIRED UNIT.................................................. 4-1
4.1 Unpacking 4-1
4.2 Packing 4-1
4.3 Transportation 4-3
4.4 Storage 4-3
CHAPTER 5 CLEANING................................................................................. 5-1
5.1 Cleaning Drive 5-1
C156-F046-01EN ix
Loading...