Fujitsu FW-S Series SERVIS Quick Start Manual

SERVIS

p

r

TM

IP-Serial FW-S Series Quick Start Guide

Introduction

- Thank you for purchasing this product. This "Quick Start

Guide" describes the items contained in the packaging,

and explains the initial setup and procedures for basic

operations. Make sure to read this manual when using

the device.

- Read the "Safety Precautions" in the CD-ROM provided

with the device in advance for its correct use. The

"Safety Precautions" includes indications to obviate any

chance of accident or damage to you and people near

you, and your property.

- For details on operations, refer to the Installer/User

Guide

Step1 Checking the Components

Check that the following items are contained in the

packaging.

- The device

- Power cable … 1

- Cat5 cable … 1

- Serial cable (for Modem) … 1

- Conversion adapters

- Loopback adapter … 1

- Flanges … 2

- Screws for flange …4

- CD-ROM …1

- Warranty certificate … 1

- China RoHS guide …1

- Quick Start Guide

rovided with the device.

D-sub25 (female)ÙRJ45 … 1
D-sub25 (male)ÙRJ45 … 1
D-sub9 (female)ÙRJ45 …1

Installer/User Guide
FW-Client Software

* This warranty is valid in Japan.

(Japanese, English) … 1 each

Step2 Connecting the Device

1. Connect the device as shown below.

2. When you have connected the device, turn on the device.

Telephone

Network

Remote User

FW-S Series

Serial Devices

Modem

Ethernet

Ethernet

Console User

Conversion adapte
D-sub9 (female)ÙRJ45

Step3 First Time Configuration

The IP address Eth0 [192.168.160.10] and Eth1 [192.168.160.10]

are set by default. By using the Cat5 cross cable

the default IP address and perform first time configuration on a

browser screen from the remote terminal.

The configuration screens in a browser is referred to as the

On-board Web Interface (hereafter referred to as "OBWI").

1. Start up the browser at the remote terminal in the same network

and access to the default IP address (192.168.160.10) of this

product by https protocols.

http://192.168.160.10/

and so on, access

2. User Login screen appears. By default, ”admin” is registered both

for the Username and Password. After entering, click [Login].

3. Wizard setting screen appears. Administer uses Wizard mode to

configure “Security”, “Network”, ”Ports”, and ”Users”.

The following section explains at least necessary set content of a

static IP address setting and the port setting, etc.

4. Click "Network", and the screen blow appears. In this page, IP

addresses of the device are set.

5. Select Static to enter the IP address and subnet mask manually,

select “static” of IPv4 method, enter values in the "Address"

"Mask" and "Gateway". And click [Save] in top right of the OBWI.

6. The network setting is reflected immediately though the screen

below appears when [Save] is clicked. Please note that the

session disconnect when you have changed IP address. Please

close the browser screen, access IP address set by the

above-mentioned again, and login.

7. Next, the port is set. Click "Ports" in the wizard setting screen, the

screen below is displayed.

（Continued to the reverse side）

＜Inquiry about our products＞

FUJITSU COMPONENT LIMITED Marketing Group

TEL: [phone]
E-mail: [e-mail] URL: http://www.fcl.fujitsu.com/en/

NC14013-0927RS-03

(Continued from the front page)

8. Confirm there is a check in "Enable all ports". To change the

default pin out when a Cisco device is connected to the

selected port, click the "Enable Cisco RJ45 Pin-Out" checkbox.

To reconfigure the connections settings to match the device

connected to the selected port, make the needed changes in

the Communication Settings area of the screen. And then click.

These settings can be changed again later.

9. Save is executed, and the screen below appears. Click [finish].

10. The First Time Configuration has completed, and Expert mode

screen appears.

Step4 Access a Serial Device

Perform an operation on a connected serial device.

1. Select “Access” from left menu in Expert mode, the content

area displays the name of this device and list of each port.

2. Select ”Serial Viewer” from the ”Action” column

3. Start up a Java applet, the following Serial Viewer window is

displayed. When the warning dialog appears, click "Run".

4. The ”Password:” prompt is displayed. Enter the current login

user password (in this case: admin).

5. The following message appears, and serial device operations

are enabled.

6. Click [Disconnect] in bottom of the Serial Viewer window or [x]

in top right of the Serial Viewer window to finish the operation.

Step5 Exit the Operation

Log out the OBWI after finishing the operation.

1. Click [LOGOUT] in top right of the OBWI.

The basic operating procedure has completed.

NOTES

Installing Java Runtime Environment (JRE).

You have to install Java Runtime Environment (JRE) of Sun

Microsystems in a remote terminal to let this document Step4

display the serial viewer screen of mention. If not yet, download

Java software in the following web site and install it.

http://www.java.com/en/

use it. In addition, by the setting of the browser, it is necessary

for JRE to become effective.

・A confirmation method of the JRE availability (IE 7)

Click [Tools] menu → [Internet Options] → [Advanced] tab.

Make sure that Java Sun [Use JRE 1.x.x._xx for <applet>

(requires restart)] is checked. (x is version No.)

Or, JRE is stored in CD-ROM, please

＜Inquiry about our products＞

FUJITSU COMPONENT LIMITED Marketing Group

* When a popup block becomes effective in a browser (e.g.

Internet Explorer), Serial Viewer window is not displayed. You

have to configure a browser to admit popup window.

TEL: [phone]
E-mail: [e-mail] URL: http://www.fcl.fujitsu.com/en/

For software setup or details on operations, refer to
the Installer/User Guide in the CD-ROM provided
with the device.

NC14013-0927RS-03