Fujitsu FUTRO S720, FUTRO S920, ESPRIMO A525-L Operating Manual

Thin Client

Operating Manual

FUTRO S720
FUTRO S920

ESPRIMO A525-L

Thank you for buying an inno

vative product from Fujitsu.

Latest information abo

ut our products, useful tips, updates etc. is available

on our website: "

http:

//www.fujitsu.com/fts/"

You ca n find driver upda

tes at: "

http://support.ts.fujitsu.com/download"

Should you have any te

chnical questions, please contact:

• our Hotline/Service

Desk (see Service Desk list or from the Internet at:

"

http://support.t

s.fujitsu.com/contact/servicedesk")

• Your sales partner

• Your sales office
We hope you enjoy using your new Fujitsu system!

Published by / Contact address in the EU

Fujitsu Te

chnology Solutions GmbH

Mies-van-der-Rohe-Straße 8

80807 Munich, Germany

"

http://

www.fujitsu.com/fts/"

Copyright

©Fujits

u Technology Solutions GmbH 2014. All rights reserved.

Publication Date

03/2014

Order No.: A26361-K1050-Z321-1-7619, edition 1

FUTRO S720
FUTRO S920

ESPRIMO A525-L

Operating Manual

ValidityoftheReferenceManual 5

Notational conventions 6

Ports and operating elements 7

Important notes 9

Getting started 15

Operation 25

System expansions 28

Technical data 60

Index 62

Remarks

Information on the product description meets the design specifications of Fujitsu and
is provided for comparison purposes. Several factors may cause the actual results to
differ. Technical data is subject to change without prior notification. Fujitsu rejects any
responsibility with regard to technical or editorial mistakes or omissions.

Trademarks

Fujitsu, the Fujitsu logo, ESPRIMO and FUTRO are registered trademarks of Fujitsu Limited
or its subsidiaries in the United States of America and other countries.

Kensington and Microsaver a re registered tradema rks of ACCO Brands.
Microsoft and Windows are trademarks or registered trademarks of the Microsoft

Corporation in the United States and/or other cou n tries.
Teradici and PCoIP are trademarks of the Teradici Corporation in the United

States of America and/ or other countries.
All other trademarks specified here are the property of their respective owners.

Copyright

No part of this publication may be copied, reproduced or translated without
the prior written consent of Fujitsu.

No part of th is publication may be saved or transferred by any electronic means
without the written approval of Fujitsu.

Contents

Contents

Validityofthe ReferenceManual ....................................................... 5

Notationalconventions ................................................................ 6

Portsand operating elements ......................................................... 7

Frontview .............................................................................. 7

Rear view .............................................................................. 8

Importantnotes ........................................................................ 9

Safety notes ............................................................................ 9

Important notes on pre

paring your FUTRO S720/S920 or ESPRIMO A525-L for use via the

Power over Ethernet mo

dule .............................................................

10

Important notes on pr

eparing your FUTRO S920 for use with an external graphics card . ......

10

Transporting the dev

ice ..................................................................

11

Cleaning the devic

e .....................................................................

11

Energy saving, dis

posaland recycling ....................................................

12

FCC Compliance Sta

tement .............................................................

13

FCC Class B Compli

ance Statement ..................................................

13

CE marking ............................................................................ 14

Gettingstarted ......................................................................... 15

Settingupthedevice .................................................................... 15

Vertical operating position . ........................................................... 15

Horizontal operating position . . ....................................................... 18

Connecting external devices . . ........................................................... 20

Connecting the cables . .............................................................. 20

Disconnecting the cables . . . . . ....................................................... 20

Portsonthedevice .................................................................. 21

Connecting a monitor . . . . . ........................................................... 21

Connecting the mouse . . . . ........................................................... 22

Connecting the keyboard . ........................................................... 22

Connecting extern al devices to the serial interface . .................................... 23

Connecting extern al devices to the USB ports . ........................................ 23

Connecting microphone , headphones, line-out and line-in devices . . ..................... 24

Connecting the mains adapter . ....................................................... 24

Connecting the device to the network (LAN) . . . ............................................ 24

Operati

on ..............................................................................

25

Switch t

he deviceon ....................................................................

25

Switch

ingoffthe device .................................................................

25

Activa

ting power-savingmode ........................................................

25

Open BI

OS Setup .......................................................................

25

PXE sy

stem boot . ......................................................................

25

Calli

ng the PXE system boot configuration menu .......................................

26

System expansions .................................................................... 28

Overview of optional system components . . . . . ............................................ 28

Possible combinationsfor the FUJITSUThinClientFUTROS920 ....................... 29

Information a bout boards . . . . . ........................................................... 30

Openingthe casing ..................................................................... 31

Adding memory ......................................................................... 32

Removingmemory modules .......................................................... 32

Fujitsu 3

Contents

Installing amemorymodule .......................................................... 32

Installing and removingthe SmartCardreader(FUJITSUThinClientFUTROS920only) ...... 33

Installing t he SmartCard reader . . . . . . ................................................. 33

Removing the SmartCard reader . . . . ................................................. 36

Information about installing and removing a speaker (optional) .............................. 37

Installing and removing a speaker: FUJITSU Thin Client FUTR O S 720 / FUJITSU Thin Client

FUTROS920 ........................................................................... 37

Installing the loudspeaker ............................................................ 37

Removingtheloudspeaker ........................................................... 40

Installing and removing a speaker: F UJITSU Desktop ESPRIMO A525-L . ................... 41

Installing aspeaker .................................................................. 41

Removingaspeaker ................................................................ 47

Installing and removing a Power over Ethernet module (optional) . .......................... 51

Installing t he Power over Ethernet module ............................................. 52

Removing the Power over Ethernet module . . . ......................................... 54

Installing and removing a board . . ........................................................ 55

Installing t he board . . ................................................................ 55

Removing the board . ................................................................ 57

Replacingthe lithiumbattery ............................................................. 58

Closingthe casing ...................................................................... 59

Technical data ........................................................................ 60

FUTRO/ESPRIMO . . . . . . ................................................................ 60

AC adapter ............................................................................. 61

Index .................................................................................. 62

4 Fujitsu

Validity of the Reference M anual

Validity of the Reference Manu

al

This Reference Manual is valid for the following systems:

• FUJITSU Thin Client FUTRO S720

• FUJITSU Thin Client FUTRO S920

• FUJITSU Desktop ESPRIMO A525-L

Fujitsu 5

Notational conventions

Notational conventions

Pay particular attention to text marked with this symbol. Failure to observe
these warnings could pose a risk to health, damage the device or lead
to loss of data. The warranty will be invalidated if the device becomes
defective through failure to observe these warnings.

Indicates important information for the proper use of the device .

►

Indicates an activity t hat must be performed



Indicates a result

This font

indicates data e ntered using the keyboard in a program dialogue or at
the command line, e.g. your password (Name123) or a command used to
start a program (start.exe)

This font

indicates information that is displayed on the screen by a program, e.g.:

Installation is complete.

This font

indicates

• terms and texts used in a software interface, e.g.: Click on Save

• names of program

sorfiles, e.g. Windows or setup.exe.

"This font"

indicates

• cross-refere

nces to another section, e .g. "Safety information"

• cross-references to an external source, e.g. a web address: For more
information, go to "

http://www.fujitsu.com/fts"

• Names of CDs

, DVDs and titles or designations for other materials,

e.g.: "CD/D

VD Drivers & Utilities" or "Safety/Regulations" manual

Key

indicates

a key on the keyboard, e.g:

F10

This font

indicate

s terms a nd texts that are emphasised or highlighted, e.g.: Do

not swit c

h off the device

6 Fujitsu

Ports and operating elements

Ports and operating elements

Ports

This chapter presents the individual hardware components of your device. This will provide
you with an overview of the ports and operating elements on the device. Please familiarise
yourself with these components before starting to work with your device.

Front view

OnswitchOffswitchPower-onindicatorSmartCardreaderFlashmemoryaccessHeadphoneportAudiooutputMicrophoneportUSB

$

#

"

!

%



1 = SmartCard reader (FUJITSU T hin Client

FUTRO S920 only, optional)
2 = Indicator for SmartCard reader
3 = Flash memory or hard disk access
4 = ON/OFF switch

5 = Microphone jack
6 = USB ports (Universal Serial Bus)
7 = Headphones port, audio output (Line Out)

Fujitsu 7

Ports and operating elements

Rear view

LANsocketPS/2mouseportInstallationopeningPS/2keyboardportMonitorportSerialportUSBportsAudiooutputDCinput connectorAudi oinputPCIslotPCIeslotSecurityLoc k

2
3

8

5

7

1

4

6

10

13

12

9

11

14

15

1 = Socket for Power over Ethernet

module (optional)
2 = Audio output (Line Out)
3 = PS/2 keyboard port
4 = USB ports
5 = USB ports
6 = DisplayPort
7 = DVI-I monitor port
8 = DC input jack (DC IN)

9 = Security Lock device
10 = Serial port
11 = Serial port (only for FUJITSU Thin

Client F UT RO S920)
12 = RJ45 socket (Local Are a Network)
13 = PS/2 mouse port
14 = Audio input (Line In)
15 = PCI/PCIe port (FUJITSU Thin Client

FUTRO S920 only, optional)

8 Fujitsu

Important notes

Important notes

ImportantnotesNotes

In this chapter you will find information regarding safety w hich it is essential to
take note of when working with your device.

Safety notes

SafetynotesNote

Please follow the safety

notes provided in the "Safety/Regulations" manual

as well as the safety note

s given below.

When installing and ope

rating the device, please observe the notes on amb ient

conditions in "

Technic

al data ", Page 60 and the instructions in "Getting started", Page 15.

Replace the lithium ba

ttery on the mainboard exactly in accordance with the

instructions in the "

R

eplacing the lithium batter y", Page 58 chapter.

Caution, compon ent

s in the system can get very hot.

The activities desc

ribed in these instructions must always be

performed with the

greatest care.

Repairs to the devi

ce must only be carried out by qualified technicians. Incorrect

repairs could put

the user at great risk (electric shock, hazardous energy emissions,

risk of fire)orcau

se serious damage to the equipment.

Operate the devi

ce only with the casing closed.

Power cable and mains adapter:
The supplied p ower cable conforms to the requirements of the country in

which you purchased your device. Make sure that t he power cable is ap proved
for use in the country in which you intend to use it.

The mains adapter’s power cable should only be connected to a mains
socket if the device is connected.

Do not use the mains adapter for oth er devices.
Use only the mains adapter which is intended for use with the device,

see chapter "

Technical data ", Page 60.

Make sure that the rated current of the mains adapter is not higher than that of
the power system to w hich you connect the mains adapte r.

ON/OFF switches do not disconnect the device from the mains voltage. To completely
disconnect the mains voltage, remove the power plug from the power socket.

Fujitsu 9

Important notes

Important notes on preparing your FUTRO S720/S920
or ESPRIMO A525-L for use via t

he Power

over Ethernet module

With the aid of the P ower over

Ethernet module, you can operate the FUTRO S720/S920

or the ESPRIMO A525-L over t

he LAN without any additional power c onnection.

You will need a suitable n

etwork infrastructure for this.

To operate the F UTRO S720

/S920 or the ESPRIMO A525-L via the Power over Ethernet module,

midspan devices confor

ming to IEEE 802.3at and shielded CAT 5 network cable or higher quality

cable are required. End

span devices will only be supported in conjunction with a hardware

classification. Fujit

su recommen ds the use of the following midspan devices:

• 1 port midspan from Mic

rosemi PD-9501G: S26361-F1744-L10

• 12 port midspan from Microsemi PD-9512G: S26361-F1 744-L 20
Because of the limit

ed power output, not all hardware configuration levels are possible for

operating the FUTR

O S720/S920 or the ESPRIMO A525-L via the Power over Ethernet

module. The follow

ing hardware configurations are possible:

Internal memory ex

pansion

according to C on figurator
mSATA module (FUTRO) / HDD (ESPRIMO) according to Configurator
SmartCard reade

r

internal SmartC

ard reader

Speaker

internal speake

r

WLAN

internal WLAN module according to Configurator
PCI/PCIe car

ds or extra interfaces

none

Depending on the system utilisation, occupancy of external interfaces (excluding th e keyboard,
screen, microphone and headset) may cause overloading of the Power over Ethernet module.
In order to support the largest p ossible occupancy of interfaces, if an overload occurs the
performance of the system is lowered by a reduction in the CPU frequency. If the CPU frequency
is permanently reduced, the occupancy of the external interfaces must be checked and reduced
accordingly to prevent damage to the Power over Ethernet module or the midspan. Alternatively,
the system can also be connected via a suitable AC adapter (see note in this Operating
Manual). The system must be switched off before the AC adapter is connected.

If you are perhaps retrofitting a FUTRO/ESPRIMO with a Power over Ethernet module,
please pay attention to the maximum possible expansion. If PCI/PCIe expansion cards are
installed (FUTRO S 920), these must be removed, otherwise the P ower over Ethernet module
or the midspan may be overloaded and switched off automa tically.

Important notes on preparing your FUTRO S920
for u se with an external graphics card

The FUTRO S920 may in addition be fitted with a graphics card. Only specially approved
graphics cards are a llowed to be used. If a graphics card is retrofittedintheFUTROS920,itis
important to note that a 65W AC adapter is needed for operation. The FUTRO S920 withou t a
graphics card is only supplied from the factory with a 40W AC adapter as standard.

10 Fujitsu

Important notes

Transporting the device

Device,Transp ortationRetransportation

Transport all parts separately in their original packaging or in a packaging which
protects them from kno cks and jolts, to the new site.

Do not unpack them until all transportation manoeuvres are completed.
If the device is broug ht from a cold environment into the room where it will be used,

condensation may occur. Before operating the device, wait until it is absolutely dry
and has reached approximately the same temperature as the installation site.

Cleaning the device

Device,Transp ortationRetransportationSystemunit,seeDevic

e

Turn off all power and equipment switches and disconne ct the power
plug from the mains outlet.

Do not clean any interior parts yourself, leave this job to a service technician.
Do not use any cleaning agents that contain abrasives or may corrode

plastic (alcohol, thinner or acetone).
Never clean the device with water! Water entering into the device could

present a serious risk to users (e.g. electric shock).
Ensure that no liquid enters the system.

Thesurfacecanbe

cleaned with a dry cloth. If particularly dirty, use a cloth that has been

moistened in mil

d domestic detergent and then carefully wrung out.

Use disinfecta

nt wipes to clean the keyboard and the mouse.

Fujitsu 11

Important notes

Energy saving, disposal and rec

ycling

DisposalEnergysavingRecyclingDrivers&UtilitiesDVDUserDocumentationDVD

You ca n find information on these subject s in chapter "Activating power-saving mode", Page 25,on
the Recovery DVD or on our website ("

http://www.fujitsu.com/fts/about/fts/environment-care/").

Information on "Ökodesign-Richtlinie":
Regulation 1275/2008, based on the EU Eco-design Directive (2009/125/EU),
defines requirements for the power consumption of electrical a nd electronic domestic
and office devices in stand-by and off mode.

In general, all FUTRO thin client products have been developed for energy-efficient
operation and low stand-by losses. Due to customer-specific and op erating system-specific
requirements, which are the priority for optimal operation, some system settings are
necessary which deviate from the above-mentioned directive.

For administrative purposes, such as remote maintenance of systems, the "Wake-on-Lan" (WoL)
function is indispensable for our customers and is therefore a default s etting. Activation of the WoL
function slightly increases the idle current and the max. permissible power draw in the Off mode can
thus be slightly exceeded. By deactivating the WoL function, it is possible to comply with the legal
requirements. Please see chapter "

Activating power-saving mode", Page 25 for the procedure.

The energy saving mode (ACPI S4 Save-to-disk), which is familiar from many current mobile
and desktop systems, is not available in the embedded operating systems for technical reasons.
Therefore, it is not possible to switch devices with this operating system automatically into Off mode.

The operating system of a thin client is stored on a flash memory with optimised size and is provided
with write protection after configuration has bee n completed by the customer. This prevents data
security from being put at risk through frequent writing to a flash memory, such as when updating
the Swapfiles in the operating system or through other applications. Every flash memory permits
only a limited number of write cycles. Both the activated write prot ection a nd the available, limited
flash memory capacity rule out the possibility of activating energy saving mode (ACPI S4).

12 Fujitsu

Important notes

FCC Compliance Statement

If the device complies with the FC C regulations, the FCC sign can be found on the typ e rating plate.

FCCClassBComplianceState

ment

DOC (INDUSTRY CANADA) NOTICES
Notice to Users of Radios and Television:

This class B digital apparatus complies with Can adian ICES-003.
The following statement applies to the products covered in this manual, unless otherwise specified

herein. The statement for other pro ducts will appear in the a ccompan ying documentation.

NOTE:

This equipment has been tested and found to comply with the limits for a "Class B" digital
device, pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian
Interference-Causing Equipment Standard ICES-003 for digital apparatus. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in strict accordance with the instructions, may cause harmful interference to radio
communications. How ever, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which c an be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the s

eparation between eq uipm ent and the receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the d

ealer or an experienced radio/TV technician for help.

Fujitsu is not responsible for any radio or television interference caused by unauthorized
modifications of this equipment or the substitution or attachment of connecting cables and
equipment other than those s pecified by Fujitsu. The correction of interferences caused by such
unauthorized modification, substitution or attachment will be the r espo nsibility of the user.

The use of shielded I/O cables is required when connecting this equipment to an y and all optional
peripheral or host devices. Fa ilure to do so may violate FCC and ICES rules.

FCC Radi

ation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The transmitters in this device must not be co-located or operated in conjunction

with any other antenna or transmitter.
To prevent radio interference to the licensed service, this device is intended to be

operated indoors and away from windows to provide maximum shielding. Equipment (or
its transmit antenna) that is installed outdoors is subject to licensing.

Users are not authorized to modify this produ ct. Any modifications invalidate the warranty.
This equipment may not be modified, altered, or ch anged in any way without signed

written permission from F ujitsu. Unauthorized modification will void the equipment
authorization from the FCC and Industry Canada and the warranty.

Fujitsu 13

Important notes

CE marking

This device complies with the requirements of EC directives 2004/108/EC "Electromagnetic
compatibility", 2006/95/EC "Low voltage directive" and 2009/125/EC "Ecod esign directive".

For this purpose, please also note the special information concerning the "Ecodesign directive"
for the FUTRO systems (see "

Energy saving, disposal and recycling", Page 12).

14 Fujitsu

Getting started

Getting started

Gettingstarted

Please observe the safety information in the "Important notes", Page 9 chapter.

Settingupthedevice

In order to ensure that the casing is sufficiently ventilated and to prevent overheating,
the device must only be operated with the base foot attached.

If the device is to be built-in, adequate ventilation must be assured.

Fit the base feet for h

orizontal or vertical operation (see "

Vertical operating

position", Page 15 and

"

Horizontal operating position", Page 18).

Vertical operati

ng position

VerticaloperatingpositionOperatingposition,verticalBasefeetSidecover

If you wish to operate the device in the vertical operating position, use
the two feet supplied for vertical operation.

Proceed as follows to prepare the device for the vertical operating position:

► Disconnect the cables if required.
► Lay the device on its top (narrow side) as shown, on a stable, flat and clean surface.

Fujitsu 15

Getting started

1

1

1

2

2

► Hook the feet into each of the openings provided for this in the casing (1).

There are lock symbols on the foot, indica ting the direction in which the
foot must be pushe d during installation or removal:

• Secure and lock th e foot = push to the left (closed lock)

• Unlock and release the foot = push to the right (open lock)

► Repeat for each foot: P ush the outer elements of th e foot evenly onto the casing

using both hands, keep the "Push" button pressed (see magnifier) and push the foot
in the direction of the arrow (2) until it is heard to engage.

16 Fujitsu

Getting started

► Stand the device on the feet.
► If necessary, reconnect any cables that were previously disconnected.

Fujitsu 17

Getting started

Horizontal operating position

If you w ish to operate the device in the horizontal operating position, use
the two feet supplied for horizontal operation.

Proceed as follows to prepare the device for the horizontal operating position:

HorizontaloperatingpositionOperatingposition,horizontalBasefeet

► Disconnect the cables if required.
► Lay the device on its right side as shown, on a stable, flat and clean surface.

1

1

2

2

► Hook the feet into each of the openings provided for this in the casing (1).

There are lock symbols on the foot, indica ting the direction in which the
foot must be pushe d during installation or removal:

• Secure and lock th e foot = push to the left (closed lock)

• Unlock and release the foot = push to the right (open lock)

► Repeat for each foot: Keep the "Push" button pressed down (see magnifier) and push

the foot in the direction of the arrow (2) until it is heard to engage.

18 Fujitsu

Getting started

► Stand the device on the feet.
► If necessary, reconnect any cables that were previously disconnected.

Fujitsu 19

Getting started

Connecting external devices

Read the documentation on the external device before connecting it.
With the exception of USB devices, always remove all power plugs

before connecting external devices!
Do not connect or disconnect cables during a thunderstorm.
Always take hold of t he act ual plug. Never unplug a cable by pulling the cable itself.
Connect and disco nnect the cables in the order described below.

Connecting the cables

► Turn off all power and equipment switches.

CordCable,

► Remove all power plugs from the grounded mains outlets.
► Connect all the c ables to the device and the external devices. Please make sure that you

always observe the safety notes provided in "

Important notes", Page 9.

► Plug all data communication cables into the appropriate sockets.
► Plug all power cables into the grounded mains outlets.

USB devices are hot-pluggable. This means you can connect and disconnect
USB cables while your device is switched on.

Additional information can be found in "

Connecting external devices to the USB

ports", Page 23 and in the documentation for the USB de vices.

Disconnecting the cables

► Switch off al

l affected devices.

Cable,

► Remove all power plugs from the grounded mains outlets.
► Unplug all d

ata communication cables from the appropriate sockets.

► Disconnect all of the cables from the device and from the external devices.

20 Fujitsu

Getting started

Ports on the device

PortsExternaldevicesDevice

The ports are located on the front and rear side of the device. The ports available on
your device depend on the configuration level you have selected. The standard ports are
marked with the symbols shown below (or similar). Detailed information on the location
of the ports is provided in the manual for the mainboard.

Headphones, black (front of
device)

Headphones

Microphone port, black (front of device)

Microphoneport

Audio output (Line Out), light
green

AudiooutputLineout

Audio input (Line In), light blue

AudioinputLinein

Serial port, turquoise

Serialport

DVI-I monitor port, white

Monitorport

USB - U niversal Serial Bus:

• blue: USB 3 .0, front of
device

• black: USB 2.0, rear of
device

UniversalSerialBus

RJ45-LAN port

LANport

PS/2 mouse port, green

MouseportPS/2mouseport

PS/2 keyboard port, purple

Keyboardport

DP DisplayPort

DisplayPort

Some of the connected devices require special software (e.g. drivers) (refer to the
documentation for the connected device and operating system).

Connecting a monitor

► Follow the instructions contained in the monitor manual to prepare the monitor

for operation (e.g . connecting cables).

Monitor,

► Connect the data cable to the req uired monitor port on your device.
► Plug the monitor power cable into the grounded mains outlet.

Fujitsu 21

Getting started

Connecting the mouse

You can connect a USB mouse or a PS/2 mouse to your device.

Mouse,Connecting,

Connecting a USB mouse

► Connect the USB mouse to one o f the USB ports on the device.

USBport,USBport

Connecting a PS/2 mouse

The PS/2 mouse is only detected by the device if you connect the mouse when
the device is switched off and then switch the device on again.

► Switch your device off.

If you do not attach a m ouse to the PS/2 mouse port, you can disable the mouse
controller in the BIOS Setup in order to free the IRQ12 for a different application.

► Connect th e PS/2 mou

se to the PS/2 mouse port of the device.

PS/2mouse,Con nect ing,PS/2mouse,

► Switch your device on again.

Connecting the keyboard

You can connect a USB keyboard or a PS/2 keyboard to your device .

Keyboard,Connecting,

Connecting a USB keyboard

Use the supplied keyboard cable only.

USBport,Connecting,

► Plug the rectangular connector of the keyboard cable into the rectangular socket

on the underside or on the rear of the keyboa rd.

► Insert the flat rectangular USB plug of the keyboard cable into one of the device’s USB ports.

USBport

Connecting a PS/2 keyboard

Use the supplied keyboard cable only.

Connect

ingaPS/2keyboard

Connect

ing,

The PS/2 keyboard is only detected by the device if you connect the keyboard
when the device is switched off an d then switch the device on again.

► Switch yo

ur device off.

► Plug the rectangular connector of the keyboard cable into the rectangular socket

on the underside or on the rear of the keyboa rd.

► Plug th

e round plug of the keyboard cable into the keyboard po rt on the device.

Keyboard,

► Switch your device on again.

22 Fujitsu

Getting started

Connecting external devices to the serial interface

SerialinterfaceSerialinterface,Externaldevices,Devices,

External devices can be connected to the serial interface (e.g. a printer or modem).

► Connect the data cable to the external device.
► Connect the data cab le to the corresponding serial interface.



For an exact description of how to connect external devices to the corresponding
port, please see the external device documentation.

Port settings

Serialinterface,

You can change the port settings (e.g. address, interrupt) in the BIOS Setup.

Device drivers

Devicedrivers,

The devices connected to the serial interface require d rivers. Your operating syste m
already includes many drivers. If the required drive is missing, install it. The latest
drivers are usually available on the Internet or will be supplied on a data carrier.

Connecting external devices to the USB ports

USBdevices,USBport,Externaldevices,Devices,

You can connect a wide range of external d evices to the USB ports (e.g.
printer, scanner, modem or keyboard).

USB devices a re hot-pluggable. This means you can connect and disconnect
USB cables while your device is switched on.

Additional information can be found in the documentation for the USB devices.

► Connect the data cable to the external device.
► Connect th e d

ata cable to one of the USB ports on your device.

Device drivers

The extern

al USB devices you connect to the USB ports usually require no driver of their

own, as the

required software is alrea dy included in the operating system. If the device

requires

separate software, please note the information in the manufacturer’s manual.

To ensure

the transmission capacity of USB 2.0, the cable from the external USB device

to the US

B port of y our device must not be longer than 3 m / 118.11 inches.

Fujitsu 23

Getting started

Connecting microphone, headphones, line-out
and line-in dev ice s

MicrophoneHeadphonesLine- out devices

► Connect the microphone to the microphone port.
► Connect the headphones to the

headphones port.

► Connect line-out devices to the audio output.
► Connect the external line

-in devices to the audio input.

Connecting the mains adapter

Mainsadapter

► Connect the mains adapter cable to the device.
► Connect the power cable to the mains adapter.
► Plug the power cable into a grounded mains outlet.

Connecting the devi

ce to the network (LAN)

LAN

► Connect the 10/100/1000 Base T network cable to the RJ45 LAN port.

24 Fujitsu

Operation

Operation

Switch the device on

► If necessary, switch the monitor on (see the operating manual for the monitor).

Device,Monitor,

► Press the ON/OFF switch on t

he front of the device.



The pow er indicator lights up and the device starts.

Switching off the device

► Shut down the operatin

g system in the proper way. In Windows: from the

Start menu select the

Shut Down option.

Device,Monitor,

► If th e operating system does not automa tically switch the device into energy-saving mode or

switch it off, press the ON/OFF switch. Warning, this could lead to a loss of data!



Ifthedeviceisswi

tched off, it consumes a minimum of energy.

The ON/OFF switch

does not disconnect the device from the m ains voltage. To

completely disco

nnect the mains voltage, remove the power plug from the power socket.

► If necessary, switch the monitor off (see the operating man ual for t he monitor).

Activating power-saving mode

Duetocustom

er requirements and requirements of the operating system, the "Wake-on-LAN"

(WoL) functi

on is set by default. The WoL function increases the idle current slightly.

In order to m

eet the requirements of EU Directive “COMMISSIO N REGULATION

(EC) No 1275

/2008 of 17 December 2008 implementing Directive 2005/32/EC”, the

default Wo

L setting must be changed as follows:

► To st a rt t

he B IOS Setup Utility after system boot, press function key

F2

.

► In the Power sub-menu, select the Low Power Soft O ff setting and switch it to enabled.
► To save th

e setting and exit the BIOS Setup Utility, press function key

F4

.



After making this change, the system will a chieve the lowest energy
saving mode during shut-down.

Open BIOS Setup

BIOS-Setup

► When t

he syst em starts, press the

F2

key (several times if necessary).



BIOS Setup will be started. Select one of t he tabs to access other setting options in BIO S Setup .

PXE system boot

PXE

systemboot

► Swi

tchthedeviceonwiththeON/OFFswitch.

Fujitsu 25

Operation

► When starting the system, press the

F12

key several times.



The boot menu is displayed.

► Select the desired boot option.

Calling the PXE system boot co

nfiguration menu

► Press the key combination

↑

+

F10

while Realtek RTL8139(X)/8130/810X Boot Agent is

displayed.



The following or a simila

r display appears on the screen:

Configuration menu screen.
The following settings are possible:

Network B oot
Protocol:

PXE (standard)
or RPL

Specification of the system boot protocol used.

Boot Order: Int 19h

The network is always started first before the local
devices are activated.

PnP/ BEV (BBS)

If a BBS-BIOS (BIOS Boot Specification) exists,
the system is started by the BBS-BIOS.

ROM Disabled

The entire mechanism for the system boot is
deactivated. The system can only be activated via
the local devices.

Int 18h

The devices set in BIOS Setup are enabled.

26 Fujitsu

Operation

Show Config
Message:

The following message can be activated or deactivated during the
system boot:

Realtek RTL8139(X)/8130/810X Boot Agent Press Shift-F10
to configure …….

Show
Message
Time:

Indicates the time in second

s for which the following m essa ge is

displayed during the system

boot:

Realtek RTL8139(X)/8130

/810X Boot Agent Press Shift-F10

to configure …….

The settings are not effective until after s aving and another PXE system boot.

Fujitsu 27

System expansions

System expansions

Upgrades,Device,System expansionComponentsServicing

Repairs to the device must only be performed by qualified technicians. Incorrect repairs
may greatly endanger the user (electric shock, fire risk) and will invalidate your warranty.

After consulting the Hotline/Help Desk, you may remove and install the components
described in this manual yourself.

As the device has to be shut down in order to install/deinstall system hardware
components, it is a good idea to print out the relevant sections of this chapter beforehand.

The following illustrations may differ slightly from your device, depending on its configuration level.
If further documentation was delivered with your device, please also read this through carefully.
In addition, before removing or installing system components, please pay attention to the following:

The device must be switched off when installing/removing the system
expansions and may not be in energy-saving mode.

Remove the power plug before opening the device.
Be careful that no wires become trapped when removing or installing components.
When installing components that become very hot, make sure that the maximum

permissible temperature of the components in operation is not exceeded.

An update of the BIO S may be required for a system expansion or hardware
upgrade. Further information can be found in the BIOS help section or if
necessary in the Technical Manual for the mainboard.

Overview o

f optional system components

The following optional system components can be installed in the various device types:

System component

FUJITSU Thin Client
FUTRO S720

FUJITSU Thin Client
FUTRO S920

FUJITSU Desktop
ESPRIMO A525-L

Hard disk

——

Installed when

delivered

SmartC

ard reader

optional optional

—

Speaker

optio

nal

optio

nal

optio

nal

PoweroverEthernet
module

optional optional optional

Third serial port

—

optional*

—

Parallel port

—

opt

ional*

—

PCIe dual serial card

—

optional*

—

PCIe ATI V3900

—

optional*

—

28 Fujitsu

System expansions

* In each case, only one of these components can be simultaneously installed in a system.

Possible combinations for the

FUJITSU Thin

Client FUTRO S920

For the FUJITSU Thin Client FUTRO S920, th e following system components can be combined
together:

System
compo­nent

Smart
Card
reader

Speaker

Power
over
Ethernet
module

Third
serial
port

Parallel
port

PCIe dual
serial
card

PCIe ATI
V3900

Smart
Card
reader

—

Speaker

—

Power
over
Ethernet
module

—————

Third
serial
port

—————

Parallel
port

—————

PCIe dual
serial card

—————

PCIe ATI
V3900

—————

Fujitsu 29

System expansions

Information about boards

Take care with the locking mechanisms (ca tche s and centring pins) when you
are replacing boards or components on boards.

Note that some components on the mainboard may be very hot if the device was
in use shortly before the casing was removed.

To preven t d amage to the board or the components and co nductors on it, please take care when
you insert or remove boards. Make sure expansion boards are inserted straightly.

Never use sharp objects (screwdrivers) for leverage.

Boards with electrostat

ic sensitive devices (ESD) are identifiable by the label

shown.
When handling boards fit

ted with ESDs, you must always observe the

following points:

• You must always disc

harge static build up (e.g. by touching a grounded

object) before work

ing.

• The equipment and tools you use must be free of static charges.

• Only touch or hold t

he boards by the edge or, if present, at the areas

marked green (Touc

h Points).

• Never touch pins or conductors on boards fitted with ESDs.

30 Fujitsu

System expansions

Opening the casing

Casing,Device,

► Switch the device off. The device must not be in power-saving mode.

Please observe the safety information in "Important notes", Page 9.
Disconnect the mains plug from the mains outlet.
Only insert the power plug after you have closed the casing.
Open the casing carefully because there are WLAN cables that lead from the casing

cover to the system and these may break if the casing is opened carelessly.

► Remove any connected wi

res which are in the way.

2

2

3

1

1

► Loosen the screws at the rear (1).
► Slide the casing cover in the direction of the arrow (2) and swing out the

casing cover towards the front (3).

Fujitsu 31

System expansions

Adding memory

MemorymoduleMainmemoryRemovingmemorySystem expansionSystemexpansion

If you want to remove or add memory, proceed as follows:

Please observe the safety information in chapter "Important notes", Page 9.
Only use memory expansions for notebooks: 1 GByte and 2 GByte modules

DDR3-1333 SO DIMM or D DR3-1600 SO DIMM.
Never use force when installing or removing a mem ory extension.
Make sure that foreign objects do not fall into the memory extension compartment.
Individual components (e.g. the processor heat sink) can become very hot

during operation. We therefore recommend that you wait one hour after
switching off the device before removing or installing the memory modules.
Otherwise, there is a risk of suffering burns!

As some components are exposed that are sensitive to static electricity, please
take note of chapter "

Information about boards", Page 30.

Removing memory mod

ules

3

2

1

1

► Carefully push the two mounting

clips outwards (1).

MemoryexpansionMemorymodule



The memory module s

naps upwards (2).

► Pull the memory module ou t of its slot

in the direction of the a rrow (3 ).

Installing a memory module

2

a

1

► Insert the memory module with the contacts

and the recess (a) facing the slot (1).

Memorye

xpansion

Memorym

odule

► Carefully push the memory module

downwards until you feel it click
into place (2).

32 Fujitsu

System expansions

Installing and removing the SmartCard reader
(FUJITSU Thin Client FUTRO S9

20 only)

If you are also installing the optional loudspeaker, install the SmartCard
reader before the loudspeaker.

Installing the SmartCard reader

SmartCardreader

If not already installed, you can fit a SmartCard reader.
► Open the casing (see "

Opening the casing", Page 3 1).

► If a PCIe board is installed, you must remove the cross piece and PCIe

board (see "

Removing the board", Page 57).

1

► Careful

ly remove the cover of the SmartCard reader bay from the casing cover (1).

Fujitsu 33

System expansions

1

2

► Place the carrier for th e SmartCard reader in the casing (1).
► Fasten the carrier with the screw (2).

34 Fujitsu

System expansions

3

2

2

1

4

► Place the SmartCard reader on the c arrier with the component side facing

downwards, in the direction of the arrow ( 1).

► Fasten the SmartCard reader onto the carrier with the screws (2).
► Connect the cable to the SmartCard reader (3) and to the connector on th e mainboard (4).
► When required, reinstall the cross piece and the PC Ie board (see "

Installing the board", Page 55).

► Clo se the casing (see "

Closing the casing", Page 59).

Make sure that the c ables are not trapped between the casing and the components.

Fujitsu 35

System expansions

Removing the SmartCard re ader

SmartCardreader

► Open the casing (see "Opening the casing", Page 31).
► If a PCIe board is installed, you must remove the cross p iece and PCIe

board (see "

Removing the board", Page 57).

1

3

3

4

2

► Disconnect the cable from the SmartCard reader (1) and from the mainboard (2).
► Undo the screw s (3).
► Lift the SmartCard reader from the carrier (4).
► When required, reinstall the cross piece and the PCIe board (see "

Installing the board", Page 55).

► Close the casing (see "

Closing the casing", Page 59).

Ensure that cables are not trapped between the casing and the components.

36 Fujitsu

System expansions

Information about installing and removing
a speaker (optional)

You can install an additional speaker in your device:

• For FUJITSU Thin Client FUTRO S720 / FUJITSU Thin Client FUTRO S920, see
chapter "

Installing and removing a speaker: FUJITSU Thin Client FUTRO S720

/ FUJITSU Thin Clien t FUTRO S920", Page 37

• For FUJITSU Desktop ESPRIMO A525-L, see chapter "Installing and removing a

speaker: FUJITSU Desktop ESPRIMO A525-L", Page 41

Installing and removi

ng a speaker: FUJITSU Thin

Client FUTRO S720 / FUJITSU Thin Client FUTRO S920

Installing the loudspeaker

Loudspeaker

The required hexagon head bolts are included in the delivery scope of the loudspeaker.

► Open the housing (see "

Opening the c asing", Page 31).

► If a P CIe board i

s installed, you must remove the cross piece and PCIe

board (see "

Re

moving the board", Page 57).

Fujitsu 37

System expansions

4

1

1

► Secure the h exagon head bolts provided into the screw holes (1).

38 Fujitsu

System expansions

2

1

1

► Insert the loudspeaker into the housing as illustrated.
► Secure the loudspeaker with the screws (1).
► Connect the loudspeaker cable to the connector on the mainboard (2).
► When required, reinstall the cross piece and the PC Ie board (see "

Installing the board", Page 55).

► Close the housing (see "

Closing the casing", Page 59).

Ensure that the cables are not trapped between the hou sing and the components.

Fujitsu 39

System expansions

Removing the loudspeaker

Loudspeaker

► Open the housing (see "Opening the casing", Page 3 1).
► If a PCIe board is installed, you must remove the cross p iece and PCIe

board (see "

Removing the board", Page 57).

1

2

2

► Disconnect the loudspeaker cable from the mainboard (1).
► Undo the screw s (2).
► Lift the loudspeaker out of the housing.
► When required, reinstall the cross piece and the PCIe board (see "

Installing the board", Page 55).

► Close the housing (see "

Closing the casing", Page 59).

40 Fujitsu

System expansions

Installing and removing a speaker: FUJITSU
Desktop ESPRIMO A525-L

Before installing a speaker in the FUJITSU Thin Client ESPRIMO
A525-L, you must first remove the hard disk.

Installing a speaker

Removing a hard disk

Harddisk

► Open the housing (see "Opening the casing", Page 31).

1

1

2

► Disconnect the cables from the hard disk (1).
► Undo th e s crew (2).

Fujitsu 41

System expansions

1

2

2

► Slide the hard disk in the direction of the arrow (1).
► Lift the hard disk out of the casing (2).

42 Fujitsu

System expansions

Installing the loudspeaker

Loudspeaker

The required hexagon head bolts are included in the delivery scope of the loudspeaker.

4

1

1

► Secure the

hexagon head bolts provided into the screw holes (1).

Fujitsu 43

System expansions

2

1

1

► Insert the loudspeaker into the housing as illustrated.
► Secure the loudspeaker with the screws (1 ).
► Connect the loudspeaker cable to the connector on the mainboard (2).

44 Fujitsu

System expansions

Installing a hard disk

Loudspeaker

2

1

2

► Insert the hard disk into the casing (1).
► Slide the hard disk in the direction of the arrow (2).

Fujitsu 45

System expansions

2

2

1

► Secure the hard disk with the screw (1).
► Connect the cables to the hard disk (2).
► Close the housing (see "

Closing the casing", Page 59).

Make sure that the cables are not trapped between the casing and the components.

46 Fujitsu

System expansions

Removing a speaker

Removing a hard disk

Harddisk

► Open the housing (see "Opening the casing", Page 31).

1

1

2

► Disconnect the cables from the hard disk (1).
► Undo th e s crew (2).

Fujitsu 47

System expansions

1

2

2

► Slide the hard disk in the direction of the arrow (1).
► Lift the hard disk out of the casing (2).

48 Fujitsu

System expansions

Removing the loudspeaker

Loudspeaker

1

2

2

► Disconnect the loudspeaker cable from the mainboard (1).
► Undo the s crews (2).
► Lift the loudspeaker out of the housing.

Fujitsu 49

System expansions

Installing a hard disk

Loudspeaker

2

1

2

► Insert the hard disk into the casing (1).
► Slide the hard disk in the direction of the arrow (2).

50 Fujitsu

System expansions

2

2

1

► Secure the hard disk with the screw (1).
► Connect the cables to the hard disk (2).
► Close the housing (see "

Closing the casing", Page 59).

Make sure that the c ables are not trapped between the casing and the components.

Installing and removing a Power over Ethernet
module (optional)

You can install an ad ditional Power over Ethernet module in your device.
Before using the module for the first time, please pay attention to the notes in

chapter "

Important notes on preparing your FUTRO S720/S920 or ESPRIMO A525-L

for use via the Power over Ethernet module", Page 10.

If you are supplying the system with power via the PoE m odule, ensure that
no additional power supply (mains adapter) is connected.

Fujitsu 51

System expansions

Installing the Power over Ethernet module

PoweroverEthernetmodule,

► Open the casing (see "Opening the casing", Page 31).
► If a PCIe board is installed, you must remove the cross p iece and PCIe

board (see "

Removing the board", Page 57).

► FUJITSU D esktop ESPRIMO A525-L: If a hard disk is installed, remove

it (see "

Removing a hard disk", Page 41).

1

2

► Break the cover (1) out of the casing.
► Place the Power over Eth ernet module in the casing with the comp onent side

facing upwards (2). Ensure that it engages in the slot.

52 Fujitsu

System expansions

1

1

► Secure the Power over Ethernet module with the screws (1).
► FUJITSU Desktop ESPRIMO A525-L: When required, reinstall the hard disk

(see "

Installing a hard disk", Page 45).

► When required, reinstall the cross piece and the PC Ie board (see "

Installing the board", Page 55).

► Clo se the casing (see "

Closing the casing", Page 59).

Make sure that the c ables are not trapped between the casing and the components.

Fujitsu 53

System expansions

Removing the Power over Ethernet module

PoweroverEthernetmodule,

► Open the casing (see "Opening the casing", Page 31).
► If a PCIe board is installed, you must remove the cross p iece and PCIe

board (see "

Removing the board", Page 57).

► FUJITSU D esktop ESPRIMO A525-L: If a hard disk is installed, remove

it (see "

Removing a hard disk", Page 41).

1

2

1

► Undo the screw s (1).
► Pull the Power over Ethernet module in the direction of the arrow (2) out

of the slot and lift it out of the casing.

► FUJITSU Desktop ESPRIMO A525-L: When required, reinstall the hard disk

(see "

Installing a hard disk", Page 45).

► When required, reinstall the cross piece and the PCIe board (see "

Installing the board", Page 55).

► Close the casing (see "

Closing the casing", Page 59).

Ensure that cables are not trapped between the casing and the components.

54 Fujitsu

System expansions

Installing a nd removing a board

You can install various boards (e.g. a graphics card) in your device.
Before using a graphics card for the first time, please pay attention to

the notes in chapter "

Important notes on preparing your FUTRO S920 for

use with an external graphics card", Page 10.

The installation and removal procedure is the same for all types of
board. A PCIe board is shown below.

Installing the board

Board,

You can only install boards with a maximum length of 170 mm.

► Enter the required settings for the board.
► Open the casing (see "

O

pening the casing", Page 31).

2

1

► Inser

t the riser card in its slot (1).

► Undo the screw (1) and remove the rear slot cover plate of the slot (2 ).

Fujitsu 55

System expansions

Do not throw away the rear slot cover plate. For cooling, protection
against fire and in order to comply with EMC regulations, you must refit
the cover plate if you remove the board.

4

2

3

1

► Insert the board into the riser card (1).
► Fix the board with the screw (2).
► Install the cross piece (3).
► Secure the cross piece with the screw (4).
► Close the casing (see "

Closing the casing", Page 59).

56 Fujitsu

System expansions

Removing the board

Board,

► Open the casing (see "Opening the casing", Page 31).

1

2

► Loosen the screw (1).
► Remov e the board from the riser card (2).

You must reinstall the rear slot cover plate due to cooling, fire protection and the EM C
regulations (regulations on electromagnetic compatibility) to be complied with.

► Reinstall the rear slot cover plate by inserting it in the installation slot from

the inside and securing it with the screw.

► Clo se the casing (see "

Closing the casing", Page 59).

Fujitsu 57

System expansions

Replacing the lithium battery

In order to permanently save the system information, a lithium battery is installed to provide
the CMOS-memory with a current. A corresponding error message notifies the user when the
charge is too low or the battery is empty. The lithium battery must then be replaced.

Incorrect replacement of the lithium battery may lead to a risk of explosion!
The lithium battery may be replaced only with an identical battery or with

a type recommended by the manufacturer.
Do not dispose of lithium batteries with household waste. They must be disposed

of in accordance with local regulations concerning special waste.
Make sure that you observe the correct polarity when replacing the lithium

battery. The plus pole must be on the top!

Lithiumbattery,Replacing,Replacing,Replacing,lithiumbatteryBattery

The lithium battery holder exists in different designs that function in the same way.

1

2

3

1

2

3

► Press t

he catch in the direction of the arrow (1).



The battery jumps out of the holder slightly.

► Remov

e the battery (2).

► Push the new lithium battery of the identical type into the holder (3) an d

press it down until it engages.

58 Fujitsu

System expansions

Closing the casing

CasingCasing cover

► Replace the casing cover on the device and push it backwards.
► Secure the casing cover with the two screws on the rear of the device.

Make sure that the c ables are not trapped between the casing and the components.

► Connect all the cables removed before.

Fujitsu 59

Technical data

Technical data

Technicaldata

FUTRO/ESPRIMO

Electrical data

FUTRO S720 FUTRO S920 ESPRIMO A525-L

Processor:

AMD eKabini 1.65 GHz
Dual Core

AMD eKabini 1.5 GHz
Quad Core

AMD eKabini 1.65 GHz

Dual Core
Rated voltage: 19 - 20 V
Max. rated

current:

2.0 A or 3.25 A 2.0 A or 3 .25 A 2 A

Dimensions (vertical operating position)

Width x D epth
x Height (with
foot):

97 mm x 195 mm x 267 mm / 3.82 inches x 7.68 inches x 10.51 inches

WidthxDepthx
Height (without
foot):

52 mm x 195 mm x 250 mm / 2.05 inches x 7.68 inches x 9.84 inches

Dimensions (horizontal operating position, without WLAN)

Width x D epth
x Height (with
foot):

295 mm x 195 mm x 72 mm / 11.61 inches x 7.68 inches x 2.63 inches

WidthxDepthx
Height (without
foot):

250 mm x 1 95 mm x 57 mm / 9.84 inches x 7.68 inches x 2.05 inches

Weight

in basic
configuration:

approx. 1 .2 kg / 2.64 lbs approx. 1.3 kg / 2.87 lbs approx. 1.4 kg / 3.08 lbs

Environmental conditions

Temperature:

• Operation

• Transpor-

tation

15 °C .... 35 °C / 59 °F ... 95 °F

–25 °C .... 60 °C / –13 °F ... 140 °F

Clea

rance

requ

ired to

ensu

re adequate

ven

tilation:

Mini

mum of 200 mm / 7.87 inches on all sides

Condensation must be avoided during ope ration.

60 Fujitsu

Technical data

AC adapter

Electrical data

Rated voltage: 100 - 240 V
Max. rated current:

1.2A(40W)or1.5A(65W)

Rated frequency:

50 - 60 Hz

Only the following adapters with Limited Power Source may be used:

• 40W: S26113-E578-V55-01 Model: ADP-40PH AD

• 65W: S26113-E557-V55-03 Model: ADP-65JH AD

Fujitsu 61

Index

Index

A

Audio input 21

line in 8

Audio output 21

line out 7
Line Out 8

B

Base feet 15, 18
Battery 58
BIOS-Setup

opening 25

Board,

installing 55
removing 57

C

Cable,

connecting 20
disconnecting 20

Casing

closing 59
Casing cover 59
Casing,

opening 31
Components

installing/removing 28
Connecting a PS/2 keyboard 22
Connecting,

keyboard 22

mouse 22

PS/2 keyboard 22

PS/2 mouse 22

USB keyboard 22
Cord

see Cable 20

D

DC input connector

DC IN 8
Device

Ports 21
Device drivers,

serial interface 23
Device,

opening 31

switching off 25

switching on 25

transporting 11

upgrades 28

Devices,

connecting 23
DisplayPort 21
Disposal 12
Drivers & Utilities DVD 12

E

Energy saving 12
External devices

Ports 21
External devices,

connecting 23

F

Flash memory a ccess 7

G

Getting started 15

H

Hard disk

removing 41, 47
Headphone port 7
Headphones 21

connecting 24
Horizontal operating position 18

I

Important notes 9
Installation opening

for m o dules 8

K

Keyboard port 21
Keyboard,

connecting 22

port 22

L

LAN 24
LAN port 21
LAN socket 8
Line in 21
Line out 21
Line-out devices

connecting 24

62 Fujitsu

Index

Lithium battery,

replacing 58

Loudspeaker

installing 37, 43
removing 40, 45, 49–50

M

Main memory

see A dding memory 32

Mains adapter

connecting 24

Memory expansion

installing 32
removing 32

Memory module

important notes 32
installing 32
removing 32

Microphone

connecting 24
Microphone port 7, 21
Monitor port 8, 21
Monitor,

Connecting 21

switching off 25

switching on 2 5
Mouse port 21
Mouse,

connecting 22

N

Note

safety 9
Notes

important 9

O

Off s witch 7
On switch 7
Operating position, horizontal 18
Operating position, vertical 15

P

PCI slot 8
PCIe slot 8
Ports 7, 21
Power over Ethernet module,

installing 52

removing 54
Power-on indicator 7
PS/2 keyboard port 8

PS/2 mouse port 8, 21
PS/2 mouse,

connecting 22
port 22

PXE system boot 25

R

Recycling 12
Removing memory

see Adding memory 32

Replacing,

lithium battery 58
Replacing, lithium battery 58
Retransportation 11

S

Safety notes 9
Security Lock

Security Lock device 8
Serial interface 23
Serial interface,

connecting devices 23

settings 23
Serial port 8, 21
Servicing 28
Side cover 15
SmartCard reader

indicator 7

installing 33

removing 36
System expansion 28, 32

see Adding memory 32
System unit, see Device 11

T

Technical data 60
Transportation 11

U

Universal Serial Bus 21
Upgrades,

device 28
USB

ports 7
USB devices,

connecting 23
USB port 22
USB port,

connecting devices 23

connecting keyboard 22

connecting the mouse 22

Fujitsu 63

Index

USB ports 8
User Documentation DVD 12

V

Vertical operating position 15

64 Fujitsu