Contents
Introduction .......................................................................................................................................1
Additional information................................................................................................................1
Important notes................................................................................................................................. 2
Safety notes.............................................................................................................................. 2
Power cable............................................................................................................................... 3
Transport................................................................................................................................... 3
Cleaning.................................................................................................................................... 3
CE marking ...............................................................................................................................3
Declaration of Conformity.......................................................................................................... 4
Checking the contents of the consignment........................................................................................4
Installing an ergonomic video workstation ......................................................................................... 5
Assembling the monitor base ............................................................................................................ 6
Mounting lower section of monitor base.....................................................................................6
Connecting the monitor .....................................................................................................................6
Operation of the monitor.................................................................................................................... 7
Switching the monitor on/off ...................................................................................................... 8
Changing the monitor settings...................................................................................................8
Adjusting rake ...........................................................................................................................9
Technical data................................................................................................................................. 10
Preset operating modes ..........................................................................................................10
Pin assignment D-SUB............................................................................................................11
Troubleshooting............................................................................................................................... 11
A26361-K1046-Z100-1-M119, edition 2
Introduction
This manual contains important information for correct set-up of your LCD monitor.
A screen controller with VGA interface is required to control the SCALEOVIEW C19-6/C19-7 LCD monitor.
The monitor processes the data supplied to it by the screen controller. The screen controller/the
associated driver software is responsible for setting the modes (resolution and refresh rate).
When putting the monitor into operation for the first time, the screen display should be optimally
adapted to the screen controller used and adjusted in accordance with your needs (see the
operating manual).
Target group
You don't need to be an "expert" to perform the operations described here. However, please
observe the safety information given in the operating instructions of the computer and in this
manual.
In the event of any problems occurring, please contact your sales outlet or our help desk.
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
► Text which follows this symbol describes activities that must be performed in the order shown.
"Quotation marks" indicate names of chapters or terms.
This font indicates filenames and menu items.
Pay particular attention to text marked with this symbol. Failure to observe this warning
endangers your life, destroys the device, or may lead to loss of data.
!
Supplementary information, remarks, and tips follow this symbol.
i
Additional information
Details of how you set the resolution and refresh rate are provided in the documentation on your
screen controller/the associated driver software.
In this "Getting Started" manual you will find information you require to operate your monitor.
Information Source Type of Information Where?
Documentation about
the graphics card or
appropriate driver
software
A26361-K1046-Z100-1-M119, edition 2 English - 1
Instructions for adjusting the
resolution and refresh rate
manufacturer-dependent
SCALEOVIEW C19-6/C19-7
Important notes
In this chapter you will find information regarding safety which is essential to take note of
with your monitor.
!
Safety notes
This device complies with the relevant safety regulations for data processing equipment, including
electronic office machines for use in an office environment. If you have any questions, contact your
sales outlet or our help desk.
● The display surface of the LCD monitor is sensitive to pressure and scratches. You should
therefore be careful with the display surface so as to avoid lasting damage (Newton rings,
scratches).
● If the device is brought into the installation site from a cold environment, condensation can
form. Before operating the device, wait until it is absolutely dry and has reached approximately
the same temperature as the installation site.
● During installation and before operating the device, please observe the instructions on
environmental conditions in the "Technical data" chapter as well as the instructions in the
"Installing an ergonomic video workstation" chapter.
● To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never
be blocked.
● The monitor automatically sets itself to a mains voltage in the range of 100 V to 240 V. Ensure
that the local mains voltage lies within these limits.
● Ensure that the power socket on the device or the grounded mains outlet is freely accessible.
● The monitor is equipped with a power cable that complies with safety standards.
● The ON/OFF switch does not disconnect the device from the mains voltage. To completely
disconnect the mains voltage, remove the power plug from the socket.
● Lay all cables so that nobody can stand on them or trip over them. When attaching the device,
observe the relevant notes in the "Connecting the monitor" chapter.
● No data transfer cables should be connected or disconnected during a thunderstorm.
● Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get inside the
device (danger of electric shock, short circuit).
● The device is not waterproof! Never immerse the device in water and protect it from spray
water (rain, sea water).
● In emergencies (e.g. damaged casing, elements or cables, penetration of liquids or foreign
matter), switch off the unit, disconnect the power plug and contact your sales outlet or our help
desk.
● The monitor must be disposed of in accordance with the local regulations for disposal of
special waste. The screen background lighting contains mercury. You must observe the
applicable handling and disposal safety regulations for fluorescent tubes.
● Only qualified technicians should repair the device. Unauthorised opening and incorrect repair
may greatly endanger the user (electric shock, fire risk).
● You may set only those resolutions and refresh rates specified in the "Technical data" chapter.
Otherwise you may damage your monitor. If you are in any doubt, contact your sales outlet or
our help desk.
2 - English A26361-K1046-Z100-1-M119, edition 2
SCALEOVIEW C19-6/C19-7
● Use a screen saver with moving images and activate the power management for your monitor
to prevent still images from "burning in".
● Store this manual close to the device. If you pass the device on to third parties, you should
pass this manual on with it.
Power cable
To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary
to replace the original cable set.
● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
● The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the
outer sheath.
● For devices which are mounted on a desk or table, type SVT or SJT cable sets may be used.
For devices which sit on the floor, only SJT type cable sets may be used.
● The cable set must be selected according to the rated current for your device.
● If necessary, replace the original power cable with a regular grounded 3-core mains lead.
Transport
● Transport the monitor with care and only in its original packaging or another corresponding
packaging fit to protect it against knocks and jolts.
● Never drop the LCD monitor (danger of glass breakage).
Cleaning
● Always pull out the power plug before you clean the monitor.
● Do not clean any interior parts yourself, leave this job to a service technician.
● Do not use any cleaning agents that contain abrasives or may corrode plastic.
● Ensure that no liquid will run into the system.
● Ensure that the ventilation areas of the monitor are free.
● The display surface of the LCD monitor is sensitive to pressure and scratches. Clean it only
using a soft, slightly moistened cloth.
Wipe the monitor casing with a dry cloth. If the monitor is particularly dirty, use a cloth which has
been moistened in mild domestic detergent and then carefully wrung out.
CE marking
The shipped version of this device complies with the requirements of the EEC
directives 89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Low voltage
directive".
A26361-K1046-Z100-1-M119, edition 2 English - 3
SCALEOVIEW C19-6/C19-7
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Product name: Colour LCD Monitor
Trade name: Fujitsu Siemens Computers Inc.
Model number(s): SCALEOVIEW C19-6/C19-7
Name of responsible party: Fujitsu Siemens Computers Inc.
Contact person: Schroettle-Henning, Bernd
Phone No.: (408) 834-0306
Fax No.: (408) 746-8299
We, Fujitsu Siemens Computers Inc., hereby declare that the equipment bearing the trade name
and model number specified above was tested confirming to the applicable FCC Rules under the
most accurate measurement standards possible, and that all the necessary steps have been taken
and are in force to assure that production units of the same equipment will continue to comply with
the Commissions requirements.
1250E. Arques Avenue
Sunnyvale, CA 94085
U.S.A.
Checking the contents of the consignment
► Unpack all the individual parts.
► Check the delivery for damage incurred during transportation.
► Check whether the delivery agrees with the details in the delivery note.
The complete LCD monitor package includes:
– one monitor with data cable
– one power cable
– one Warranty Booklet
– this "Getting Started" manual
Should you discover that the delivery does not correspond to the delivery note, notify your local
sales outlet immediately.
4 - English A26361-K1046-Z100-1-M119, edition 2
We recommend that you keep the original packaging material. Keep it for future
transportation.
i
SCALEOVIEW C19-6/C19-7
Installing an ergonomic video workstation
Before you set up your equipment, you should select a suitable position for working at the monitor.
Please observe the following advice when installing a video workstation.
1
1
600 mm 600 mm
2
2
1 = Windows
Avoid direct and reflected glare.
Avoid glare from electric
lighting.
1 = Edge of desk
2 = Permissible reaching
sector
Position the keyboard where it
is easiest to reach.
60°
1
0°
65°
65°
30°
30°
1
2
22
1 = Preferable viewing sector
2 = Permissible viewing
sector
Position the monitor for
Keep ventilated areas clear.
1 = approx. 90° and more
2 = approx. 90°
Remember to maintain correct
posture.
optimum viewing. The viewing
distance to the monitor should
be approximately 50 cm.
Depending on the situation, the use of a swivel arm or wall bracket (VESA FPMPMI), are available
from specialised dealers, may be advisable.
A26361-K1046-Z100-1-M119, edition 2 English - 5
SCALEOVIEW C19-6/C19-7
Assembling the monitor base
The monitor surface is susceptible to scratching! Therefore, lay the monitor on a soft
surface when mounting or removing the monitor base.
!
Mounting lower section of monitor base
When delivered the lower section of the monitor base is removed. If you do not want to use a
swivelling arm or a wall mounting, you must mount the lower section of the monitor base.
Mounting lower section of monitor base
► Put the monitor base onto a table.
► Fit the monitor so that its four hooks slot into the recesses on the monitor base.
► Press the monitor into the recesses, until it audibly engages.
If you operate the monitor with the swivel arm or wall bracket, it may not be turned by
180°.
!
Connecting the monitor
Please take note of the safety information in the "Important notes" chapter.
!
Do not cover the ventilation openings of the monitor.
The computer power plug must be pulled out!
Information on the computer connections and interfaces is contained in the operating manual for
your computer.
► Be sure that the monitor and the computer are switched off.
6 - English A26361-K1046-Z100-1-M119, edition 2
SCALEOVIEW C19-6/C19-7
(1)
(2)
PC
1 = Data cable (D-SUB) 2 = Power cable
The data cable (1) is permanently attached to the monitor. It has a 15-pin D-SUB connector for the
monitor port of the computer.
► Connect the data cable (1) to the (active) monitor port on the computer and secure the plug-in
connection by tightening the safety screws.
► Connect the plug on the power cable (2) supplied to the power connector of the monitor.
► Connect the other connector of the power cable (2) supplied into a properly earthed mains
► Plug the power connector of the computer into a properly grounded mains outlet.
If your computer has two monitor ports ("onboard" screen controller and separate
graphics card), the monitor port for the separate graphics card is usually active.
i
outlet and ensure a secure connection.
When you start working with your monitor for the first time you should install the
appropriate graphics drivers for your application software. Details of how to do this are
i
provided in the documentation on your screen controller/the associated driver software.
Operation of the monitor
1 = MENU button for calling OSD menu (On-
Screen Display)
MENU DOWN UP AUTO
control (to degrease or increase the sound level)
when OSD is not displayed.
3 = AUTO button (auto-adjustment)
4 = Power indicator
5 = ON/OFF switch
1 2 3
A26361-K1046-Z100-1-M119, edition 2 English - 7
DOWN / UP buttons act as hot key for volume
5
4
2 = Setting buttons
SCALEOVIEW C19-6/C19-7
Switching the monitor on/off
The ON/OFF switch (5) is used for switching the monitor on and off.
The power indicator (4) lights up when the monitor is switched on. The power indicator goes off
when the monitor is switched off.
When you switch the computer system on, you must proceed in the following order:
► First switch on the LCD monitor with the ON/OFF switch (5).
► Then switch on the computer.
Changing the monitor settings
With the buttons on the control panel, call up and use the integrated OSD (On-Screen display)
menu.
To set the OSD menu, perform the following steps:
► Press the MENU button to activate the OSD menu.
The main menu appears on the screen with icons for the setting functions.
All possible adjustments of the monitor using the OSD menu are described in the following.
An icon is marked. The name of the functions is
displayed (here
► If necessary, press the setting buttons
(UP/DOWN) to mark another icon.
► Press the MENU button to select the
highlighted icon.
► Press the setting buttons (UP/DOWN), to
make the settings.
► Select the EXIT function to exit the OSD
menu.
EXIT).
Adjusting the brightness and contrast
Setting the brightness of the display
With this function you change the brightness of the background lighting.
Setting the contrast of the display
With this function you modify the contrast of bright colour tones.
Adjusting size and position
Adjusting the horizontal position
With this function you move the picture to the left or to the right.
Adjusting the vertical position
With this function you move the picture up or down.
8 - English A26361-K1046-Z100-1-M119, edition 2
SCALEOVIEW C19-6/C19-7
Adjusting the horizontal size
With this function you adjust the picture width to eliminate vertical picture
disturbances.
/
Setting colour temperature and colours
/
Carrying out auto-adjustment and activating factory settings
Setting display of the OSD menu
Exiting the OSD menu
/
Eliminating picture interference
With this function you fine-tune your monitor to eliminate picture interference.
Selecting colour
In the user-defined setting you can change the colour ratios of the basic colours
(red, green, blue) as required.
COOL (9300K)
WARM (6500K)
Performing auto-adjustment of the monitor
Activating the factory settings
With this function all settings are reset to the factory settings without prompting for
= The picture appears bluer and lighter
= The picture appears redder and paper-whiter
confirmation. Factory settings are provided for the predefined operating modes
(see chapter "Technical data").
Setting language for the OSD menu
Setting the horizontal position of the OSD menu
With this function you move the OSD menu to the left or to the right.
Setting the vertical position of the OSD menu
With this function you move the OSD menu up or down.
Exiting the OSD menu
Adjusting rake
The rake of the monitor can be adjusted by -5° (forward) and +30° (back) from its vertical position.
► Grasp the monitor with both hands on the right and left edge of the casing and adjust it to the
desired rake.
A26361-K1046-Z100-1-M119, edition 2 English - 9
SCALEOVIEW C19-6/C19-7
Technical data
Dimensions and weight (LCD monitor)
Visible diagonals: 48 cm
Dot pitch: 0.294 mm
Screen size: 376 mm x 301 mm
Maximal resolution: 1280 x 1024 pixels
Dimensions (W x H x D)
incl. monitor base:
Dimensions box (W x H x D):
Weight: approx. 4.8 kg
Electrical data
Video: analogue, positive, 0.7 Vpp, 75 Ω
Synchronisation: Separate Sync. TTL, positive or negative
Horizontal frequency: 30 kHz .... 80 kHz (multi-scanning)
Refresh rate: 60 Hz .... 75 Hz
Maximum pixel rate: 135 MHz
Power supply: switches automatically
Total power consumption: < 60 W
426 mm x 416 mm x 210 mm
485 mm x 527 mm x 140 mm
100 V -240 V, 50 Hz - 60 Hz
< 3 W in the energy-saving mode (standby mode, suspend
mode and OFF mode)
,1.0 Hz max.
Environmental conditions
Environment class 3K2, IEC 721
Operating range:
Humidity:
Condensation must be avoided.
5 °C .... 35 °C
20 % .... 85 %
Preset operating modes
The picture position and size have been set to optimum values at the factory for the operating
modes listed above.
Horizontal frequency Refresh rate Display resolution
31.5 kHz
31.5 kHz
37.5 kHz
37.9 kHz
46.9 kHz
48.4 kHz
60.0 kHz
64.0 kHz
10 - English A26361-K1046-Z100-1-M119, edition 2
79.9 kHz
70 Hz
60 Hz
75 Hz
60 Hz
75 Hz
60 Hz
75 Hz
60 Hz
75 Hz
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1280 x 1024
1280 x 1024
SCALEOVIEW C19-6/C19-7
For ergonomic reasons, a screen resolution of 1280 x 1024 pixels is recommended. Because of the
technology used (active matrix) an LCD monitor provides a totally flicker-free picture even with a
refresh rate of 60 Hz.
Pin assignment D-SUB
1
5
6
10
11
15
Pin Meaning Pin Meaning
1 Video input red 9 +5 V (DDC)
2 Video input green 10 Sync. earth
3 Video input blue 11 Earth
4 Earth 12 DDC-Data
5 Earth 13 H. sync
6 Red video earth 14 V. sync
7 Green video earth 15 DDC Clock
8 Blue video earth
Troubleshooting
Should an error occur, first check the following points. If the distortion is still not eliminated, the
monitor should, if possible, be checked on another computer.
If you are unable to solve the problem, please inform our help desk.
Having this problem? Check the following points:
No screen display
(power indicator does not light)
No screen display
(power indicator lights)
A26361-K1046-Z100-1-M119, edition 2 English - 11
► Check whether the monitor is switched on.
► Check whether the power cable on the monitor is
connected correctly.
► Check whether the computer is switched on.
► Check whether the data cable for the monitor is
correctly attached to the monitor port on the
computer.
► Press any key on the computer keyboard - the
computer may be in energy saving mode.
► Alter the brightness and/or contrast until you get a
picture.
SCALEOVIEW C19-6/C19-7
Having this problem? Check the following points:
Picture position is not correct The monitor recognises an undefined mode (see "Technical
Picture is shaking ► Check whether the data cable for the monitor is
Picture disturbances (vertical lines)
Picture disturbances (horizontal lines,
picture noise)
data").
► Press the AUTO button to conduct the auto-
adjustment of the screen.
correctly attached to the monitor port on the
computer.
► Press the AUTO button to conduct the auto-
adjustment of the screen.
► Press the AUTO button to conduct the auto-
adjustment of the screen.
► Press the AUTO button to conduct the auto-
adjustment of the screen.
The screen becomes darker
The background lighting has a limited lifetime. If your
monitor display should become too dark, the background
lighting will have to be exchanged.
► Please contact our help desk.
Permanently unlit or lit pixels
The standard of production techniques today cannot guarantee an absolutely fault-free screen
display. A few isolated constant lit or unlit pixels may be present. The maximum permitted number
of pixels faults is stipulated in the stringent international standard ISO 13406-2 (Class II).
Example: a 19" flat-screen monitor with a resolution of 1280 x 1024 has 1280 x 1024 = 1310720
pixels. Each pixel consists of three subpixels (red, green and blue), so there are almost 4 million
dots in total.
According to ISO 13406-2 (Class II), a maximum of 6 pixels and 7 subpixels may be defective, i. e. a
total of 25 faulted dots. This corresponds to approx. 0.00062 % of the entire screen surface!
12 - English A26361-K1046-Z100-1-M119, edition 2
Loading...