Fujifilm J12, J10 Owner's Manual

Getting Ready

Using the Camera

OWNER’S MANUAL

This manual will show you how to use your FUJIFILM DIGITAL CAMERA FinePix J10 / FinePix J12 correctly. Please follow the instructions carefully.

Advanced Features

Camera Connection

Troubleshooting

BL00710-201(1)

• Photography

• Playback

•Movie

Settings

Software

Installation

Appendices

Warning

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

For customers in the U.S.A.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for

help. You are cautioned that any changes or modifications not expressly approved in this manual could void the user’s authority to operate the equipment.

Notes on the Grant:

To comply with Part 15 of the FCC Rules, this product must be used with a Fujifilm-specified ferrite-core A/V cable, USB cable, and DC supply cord.

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

For customers in Canada

CAUTION

This Class B digital apparatus complies with Canadian ICES-003.

Please read the Safety Notes (separate note “Notes and Cautions”) and make sure you understand them before using the camera.

Perchlorate Material-special handling may apply, See http://www.dtsc.ca.gov/hazardouswaste/ perchlorate.

IMPORTANT

BEFORE OPENING THE CD-ROM PROVIDED BY FUJIFILM Corporation, PLEASE READ THIS END USER LICENSE AGREEMENT CAREFULLY. ONLY IF YOU AGREE WITH THIS AGREEMENT, SHOULD YOU USE THE SOFTWARE RECORDED ON THE CD-ROM. BY OPENING THE PACKAGE, YO U ACCEPT AND A GREE TO BE BOUND BY THIS AGREEMEN T.

This End User License Agreement (“Agreement”) is an agreement between FUJIFILM Corporation (“FUJIFILM”) and you, which sets forth the terms and conditions of the license granted for you to use the software provided by FUJIFILM. The CD-ROM contains third party software. In case a separate agreement is provided by a third party supplier for its software, the provisions of such separate agreement shall apply to the use of such third party software, prevailing over those of this Agreement.

1. Definitions.

(a) “Media” means the CD-ROM titled “Software for FinePix”- which is

provided to you together with this Agreement. (b) “Software” means the software which is recorded on Media. (c) “ Documentation” means the operation manuals of Software and

other related written materials which are provided to you together

with Media. (d) “Product” means Media (including Software) and Documentation

collectively.

2. Use of Software.

FUJIFILM grants to you a nontransferable, nonexclusive license: (a) to install one copy of Software onto one computer in binary machine

executable form; (b) to use Software on the computer onto which Software is installed; and (c) to make one backup copy of Software.

3. Restrictions.

3.1 You shall not distribute, rent, lease or otherwise transfer all or any

part of Software, Media or Documentation to any third party without

FUJIFILM’s prior written consent. You also shall not sublicense,

assign or otherwise transfer all or any part of the rights granted to

you by FUJIFILM under this Agreement without FUJIFILM’s prior

written consent.

3.2 Except as expressly granted by FUJIFILM hereunder, you shall not

copy or reproduce all or any part of Software or Documentation.

3.3 You shall not modify, adapt or translate Software or Documentation.

You also shall not alter or remove copyright and other proprietary

notices that appear on or in Software or Documentation.

3.4 You shall not, or shall not have any third party, reverse-engineer,

decompile, or disassemble Software.

NOTICE

End User License Agreement

Be sure to read this page before using the software.

4. Ownership.

All copyrights and other proprietary rights to Software and Documentation are owned and retained by FUJIFILM or the third party suppliers as indi cated on or in Software or Documentation. Nothing contained her ein shall be construed, expressly or implicitly, as transf erring or granting any right, license, or title to you other than t hose explicitly granted under this Agreement.

5. Li mited Warrant y.

FUJIFILM warrants to you that Media is free from any defect in material and workmanship under normal use for ninety (90) days from the date of your receipt of Media. Should Media not meet the foregoing warranty, FUJIFILM shall replace such defective Media with other Media bearing no defect. FUJIFILM’s entire liability and your sole and exclusive remedy with regard to any defect in Media shall be expressly limited to such FUJIFILM’s replacement of Media as provided herein

6. DI SCLAIMER OF WARRAN TY.

EXCEPT AS PROVIDED IN SECTION 5 HEREIN, FUJIFILM PROVIDES PRODUCT “AS IS” AND WITHOUT WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED. FUJIFILM SHALL MAKE NO WARRANTY, EXPRESS, IMPLIED OR STATUTORY, AS TO ANY OTHER MATTERS, INCLUDING, BUT NOT LIMITED TO NON-INFRINGEMENT OF ANY COPYRIGHT, PATENT, TRADE SECRET, OR ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY, MERCHANTABILITY, OR FITNESS FOR ANY PARTICULAR PURPOSE.

7. LI MITATION OF LIABILITY.

IN NO EVENT SHALL FUJIFILM HAVE ANY LIABILITY FOR ANY GENERAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR OTHER DAMAGES (I NCLUDING DAMAG ES FOR LOSS OF PROFITS OR LOST SAVINGS) INCURRED FROM THE USE OF OR INABILITY TO USE PRODUCT EVEN IF FUJIFILM HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

8. No export.

You acknowledge that neither Software nor any part thereof, will be transferred, or exported to any country or used in any manner in violation of any export control laws and regulations to which Software is subject.

9. Termination.

In case you breach any of the terms and conditions hereof, FUJIFILM may immediately terminate this Agreement without any notice.

10. Term.

This Agreement is effective until the date when you cease to use Software, unless earlier terminated in ac cordance with Se ction 9 hereof.

11. Obligation upon termination.

Upon termination or expiration of this Agreement, you shall, at your own responsibility and expense, delete or destroy immediately all Software (including its copies), Media and Documentation.

12. Governing Law.

This Agreement shall be governed by and construed in accordance with laws of Japan.

EC Declaration of Conformity

We Name: FUJIFILM Electronic Imaging Europe GmbH Address: Benzstrasse 2

declare that the product Product Name: FUJIFILM DIGITAL CAMERA FinePix J10 / FinePix J12 Manufacturer’s Name: FUJIFILM Corporation Manufacturer’s Address: 7-3, AKASAKA 9-CHOME, MINATO-KU,

conforms to the following Standards:

following the provision of the EMC Directive (2004/108/EC) and Low Voltage Directive (2006/95/EC).

47533 Kleve, Germany

TOKYO 107-0052, JAPAN

Safety: EN60950-1: 2001 EMC: EN55022: 2006 Class B

EN55024: 1998 + A1: 2001 + A2: 2003 EN61000-3-3: 1995 + A1: 2001 + A2: 2005

Kleve, Germany

Place

This product comes with batteries. When these are empty, you shouldn’t throw them away but deliver them as domestic chemical refuse.

February 1, 2008

Signature/Managing DirectorDate

Disposal of Electric and Electronic Equipment in Private Households

Disposal of used Electrical & Electronic Equipment (Applicable in the European Union and other European countries with

separate collection systems)

This symbol on the product, or in the manual and in the warranty, and/or on its packaging indicates that this product shall not be treated as household waste. Instead it should be taken to an applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate waste handling of this

If your equipment contains easy removable batteries or accumulators please dispose these separately according to your local requirements. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you have purchased the product.

In Countries outside the EU:

If you wish to discard this product, please contact your local authorities and ask for the correct way of disposal.

product.

Contents

Warning................................................................. 2

IMPORTANT ......................................................... 3

EC Declaration of Conformity................................ 4

Disposal of Electric and Electronic Equipment in

Private Households ......................................... 5

Contents ................................................................ 6

About this Manual ................................................. 8

Accessories Included ............................................ 9

Camera Parts and Features ................................ 10

Example of LCD Monitor Text Display ................ 11

Getting Ready

Charging the Battery ........................................... 12

Loading the Battery ............................................. 14

Loading the Memory Card................................... 16

Turning On and Off ............................................. 19

Setting the language, date, and time .......... 20

Correcting the Date and Time ............................. 23

Selecting the Language ...................................... 24

Using the Camera

Taking Pictures (AUTO Mode) ............................ 25

Taking pictures with the focus and exposure

locked ....................................................... 29

Adjusting the shot composition ................... 31

Viewing the Images............................................. 32

Erasing the Images/Movies ............................ 36

Using the erase button ( /n) .................... 36

Erasing the images using

[PLAYBACK MENU]................................. 36

Advanced Features — Photography

Using the Photography Functions —

Procedure of Setting ..................................... 39

Setting the Shooting Mode ................................. 41

Shooting Mode ................................................... 42

e Macro (Close-up) ........................................... 47

d Setting the Flash............................................. 48

* Self-Timer ...................................................... 50

j Increasing Monitor Brightness ...................... 52

Using [SHOOTING MENU] ................................ 53

Setting the [SHOOTING MENU] ................ 53

[SHOOTING MENU]........................................... 56

Changing the sensitivity setting

([ ISO]) ................................................. 56

Changing the quality setting

([ QUALITY]) ........................................ 56

Adjusting exposure compensation

([ EXP. COMPENSATION]) ................. 58

Adjusting color balance

([ WHITE BALANCE]) .......................... 59

Taking pictures continuously

([ CONTINUOUS])............................... 60

Advanced Features — Playback

Using [PLAYBACK MENU] ................................. 61

Setting the [PLAYBACK MENU] ................ 61

[PLAYBACK MENU] .......................................... 62

Setting automatic playback

([ SLIDE SHOW]) ................................. 62

DPOF set frame

([ PRINT ORDER (DPOF)]) ................. 62

Protecting the images ([ PROTECT])...... 66

Copying the images ([ COPY])................ 67

Rotating the images

([ IMAGE ROTATE]) ............................. 70

Trimming the images ([ TRIMMING]) ...... 71

Advanced Features — Movie

r Recording Movies .......................................... 73

Set the camera to r Movie mode.............. 73

Record movies ............................................ 74

Changing movie size................................... 75

w Playing Back Movies ..................................... 76

Settings

[ SET-UP]........................................................ 78

Using the [SET-UP] menu........................... 78

[SET-UP] menu option ................................ 79

Camera Connection

Connecting to a TV ............................................. 87

Connecting Camera Directly to Printer —

PictBridge Function ....................................... 88

Software Installation

Installation on a Windows PC ............................. 92

Installation on a Mac OS X ................................. 94

Connecting to a PC ............................................. 97

Using FinePixViewer................................. 100

Appendices

System Expansion Option ................................ 102

Accessories Guide ........................................... 103

Using Your Camera Correctly .......................... 105

Notes on the xD-Picture Card™, the SD Memory

Card and the Internal Memory .................... 106

Warning Displays ............................................. 107

Troubleshooting

Troubleshooting................................................ 111

Specifications ................................................. 117

Explanation of Terms ..................................... 124

FUJIFILM Digital Camera Worldwide

Network..................................................... 125

Usable Memory Cards

You can use the xD-Picture Card, the SD Memory Card and the SDHC Memory Card with the FinePix J10 / FinePix J12. In this Owner’s Manual, these cards are expressed as “Memory Card”.

About this Manual

Z About marks

CAUTION

This mark denotes issues that may affect the camera’s operation.

CHECK

This mark denotes points to notice in the camera’s operation.

MEMO

This mark denotes additional topics that complement the basic operating procedures.

Z Usable Memory Cards

You can use the xD-Picture Card, the SD Memory Card and the SDHC Memory Card with the FinePix J10 / FinePix J12. In this Owner’s Manual, these cards are expressed as “Memory Card”.

Z About illustration

Up, down, left, and right are indicated by black triangles in the Owner’s Manual. Up or down is shown as n or o, and left or right is shown as p or q.

When pressing DISP/BACK:

When pressing q:

Z About cables

The cables used for FinePix J10 / FinePix J12 are following:

• A/V cable for FinePix J10 / FinePix J12

• USB cable for FinePix J10 / FinePix J12 In this manual, these cables are expressed as “A/V cable” and “USB cable”.

Z Note

In this manual, the menu names and messages displayed on the LCD monitor of the camera or PC screen appear in square brackets ([ ]).

Accessories Included

Make sure that all the below accessories are included. Note that accessories may vary depending on model.

• Rechargeable Battery NP-45 (1)

•Strap (1)

• Battery Charger BC -45A (1 set)

Cord typeWall type

• A/V cable (1)

•USB cable (1)

• CD-ROM (1) Software for FinePix

• Owner’s Manual (this manual) (1)

• Notes and Cautions (1)

Attaching the strap

Attach the strap as shown in 1 and 2. When attaching the strap, move the fastener to adjust the length and slightly away from the end of the strap, as shown in figure 1.

Camera Parts and Features

• Refer to the pages in parentheses for information on using the camera parts or features.

A Shutter button B Self-timer lamp (p.51) C Lens (Lens cover) D Microphone E ON/OFF button F Flash (p.48) G Indicator lamp (p.28) H DISP (Display)/BACK button (p.31, 32) I LCD monitor J MENU/OK button K p/e Macro button (p.47) L Speaker M Tripod mount N o/* Self-timer button (p.50) O Battery compartment P Memory Card slot (p.16) Q Zoom button (p.26, 33) R w (Playback) button S n/j Low light view button (p.52)/

T Strap mount U q/d Flash button (p.48) V ; USB socket

W Battery cover

Erase button (p.36)

A/V OUT (Audio/Visual output) socket (p.87)

Example of LCD Monitor Text Display

Z Shooting mode

A ( Self-timer (p.50) B e Macro (close-up) (p.47) C C Flash (p.48) D s Shooting mode (p.41) E Battery level indicator

(p.22)

F AF frame (p.26) G Date/Time (p.20) H 9 White balance (p.59) I f Continuous shooting (p.60) J iN Quality mode (p.56) K Number of available frames

(p.122)

Z Playback mode

A w Playback mode (p.32)

B u DPOF (p.62) C F Protection (p.66) D Frame number (p.81)

E Present (p.32)

FinePix J10 / FinePix J12 has internal memory that can store images without Memory Card. Y appears on the LCD monitor when the internal memory is active.

L ISO 100 Sensitivity (p.56) M { AF warning (p.107) N | Camera shake warning

(p.107)

O Increasing monitor

brightness (p.52)

P Y Internal memory (p.18) Q S Exposure compensation

(p.58)

Charging the Battery

The battery is not fully charged at shipment and must be fully charged before being used.

Z Compatible battery

Rechargeable Battery NP-45 (1)

Terminals

CAUTION

• The battery is not fully charged at shipment and must be fully charged before being used.

• Do not stick labels onto the battery as this could cause the battery to become jammed inside the camera.

• Any contact between the battery terminals could cause the battery to short circuit and overheat.

• See “Notes and Cautions” for information on the battery.

• Always use the Rechargeable Battery NP-45 (included). The use of other brands of rechargeable battery could cause faults or damage to the camera.

• Do not split or peel outer labels of the battery.

Indicator

1 Load the battery into the battery charger

BC-45A.

Set the battery correctly as indicated by the polarity icon.

Rechargeable Battery NP-45

Battery Charger BC-45A

Rechargeable Battery NP-45

Battery Charger BC-45A

2 Plug the battery charger into a power outlet.

The charging indicator lights orange and charging begins. When charging is completed, the indicator turns off. Charging completes after about 100 minutes.

To power outlet

To power outlet

Z <Charging Indicator and Statuses>

Charging

Indicator

Off

Lit orange Charging –

Blinking orange

Status Action

Battery not loaded

Fully charged (charging complete)

Battery fault during charging

Load the battery to be charged.

Remove the battery from the battery charger.

Unplug the battery charger and remove the battery from the battery charger.

CAUTION

• Unplug the battery charger from the power outlet when it is not in use.

• If the terminals of battery are soiled, it may not be possible to charge it. Clean the battery terminals and battery charger terminals with a clean, dry cloth.

• Charging times increase at low temperatures.

• The NP-45 gradually loses its charge even when not used. Charge a NP-45 just before taking pictures (in the last day or two).

Getting Ready

Loading the Battery

Battery is required to operate the digital camera. At first, load the battery in the camera.

1 Open the battery cover.

CHECK

Check that the camera is turned off before opening the battery cover.

CAUTION

• Do not open the battery cover while the camera is on. This could damage the Memory Card or ruin the image files on the Memory Card.

• Do not apply force to the battery cover.

2 Load the battery.

While pushing the battery release catch aside, load the battery by aligning the indicator (A orange) and the battery indicator (B orange). Check that the battery is firmly held in place.

Battery release catch

Align the orange parts

CAUTION

• Load the battery in the correct direction.

• If the battery is loaded with the arrow pointing toward opposite direction from the camera, or the indicators are not aligned, it may become jammed and damaged. Use the battery carefully to avoid overheating, igniting or exploding. If the battery is loaded incorrectly, contact a FUJIFILM dealer. Do not use excessive force to remove the battery from the camera.

3 Close the battery cover.

To remove the battery

Battery release catch

Open the battery cover, and unlock the battery release catch with your finger.

CAUTION

Make sure the camera is turned off before removing the battery.

Getting Ready

Loading the Memory Card

Although you can store pictures in the camera’s internal memory, you can store many more images on the Memory Card (sold separately). You can use the xD- Picture Card and the SD Memory Card with the FinePix J10 / FinePix J12. In this Owner’s Manual, these cards are expressed as “Memory Card”.

SD Memory Cards/SDHC Memory Cards

They are operation-checked at FUJIFILM Corporation. Maker: SanDisk

MEMO

• Compatible Memory Cards will be updated in our website: http://www.fujifilm.com/products/digital_cameras/index.html

• Depending on the SD Memory Card, recording of movies may be interrupted. Use of above mentioned SD Memory Cards are recommended.

• The camera is not compatible with multimedia cards.

1 Open the battery cover.

2 Insert a Memory Card.

(xD-Picture Card)

(SD Memory Card)

CAUTION

Be sure to unlock the protection of the SD Memory Card before inserting it. If it is locked, recording/deleting images, as well as formatting are not available. To unlock the protection, slide the switch back, and the SD Memory Card will work normally.

3 Close the battery cover.

Getting Ready

Protection switch

CAUTION

• A new SD Memory Card or a card previously used on a PC or any device other than the camera should be formatted (➝p.84) on the camera before use.

• Do not use a miniSD adaptor or a microSD adaptor which have exposed contact areas on the back. Use of these adaptors may cause a malfunction or damage due to the improper contacts. A miniSD adaptor or microSD adaptor bigger than SD Memory Card standard size may beco me stuck. Pulling out forcefully may cause a malfunction. In that case, contact your FUJIFILM dealer.

How to replace the Memory Card

Push the Memory Card into the slot and then slowly remove your finger. The lock is released and the Memory Card is pushed out.

Continued Q

Loading the Memory Card

124NN

AUTO

CAUTION

• When storing Memory Cards, make sure that they are kept out of the reach of children. A Memory Card could be swallowed and cause suffocation. If a child swallows a Memory Card, seek medical attention or call emergency number right away.

• If the Memory Card is oriented incorrectly, it will not go all the way into the slot. Do not apply force when inserting a Memory Card.

• Note that the Memory Card may spring out if you release your finger quickly from the card immediately after the lock is released.

• Operation of this camera is only guaranteed when it is used with FUJIFILM xD-Picture Card and operationchecked SD Memory Card (➝p.16).

• See p.106 for information on the xD-Picture Card, SD Memory Card and the internal memory.

MEMO

• The size of an image file varies depending on the subject. For this reason, the number recorded may not represent the actual number of frames.

• See p.122 for information on the standard number of available frames.

Z About internal memory

AUTO

FinePix J10 / FinePix J12

has internal memory that can store images without Memory Card. Y appears on the LCD monitor when internal memory is active.

When a Memory Card (sold separately) is inserted

[Record images]: Record images to a Memory Card. [Playback images]: Playback images in a Memory Card.

When a Memory Card (sold separately) is not inserted

[Record images]: Record images to internal memory. [Playback images]: Playback images in internal memory.

Z About images in the internal memory

Images held in the camera’s internal memory may be corrupted or erased due to problems such as camera faults. Save your important data to another media (i.e., DVD-R, CD-R, CD-RW, hard disk, etc.). It is possible to transfer saved images on the internal memory to a Memory Card (➝p.67).

CAUTION

Erase the unnecessary images in the internal memory. (➝p.36)

Turning On and Off

Turning the camera on in Shooting mode

Press ON/OFF down fully to turn the camera on. Press ON/OFF again to turn the camera off.

MEMO Changes between Shooting mode and Playback mode

Press w during shooting to change to Playback mode. Press the shutter button down halfway to return to Shooting mode.

CAUTION

• The lens moves and the lens cover opens when turning the camera on in Shooting mode. Take care not to obstruct the lens.

• Take care not to get fingerprints on the camera lens as this will result in impaired image quality in your shots.

• The ON/OFF button does not completely disconnect the camera from its power supply.

Turning the camera on in Playback mode

Press w for about 1 second to turn the camera on in Playback mode. Press w during playback to turn the camera off.

MEMO

To change to Shooting mode, press the shutter button down halfway.

Getting Ready

Turning On and Off

SETNONO

START MENU

/ LANG.

SETNONO

DATE / TIME NOT SET

YY.MM.DD

1. 1 12:00 AM

2006

2007

2009

2008

2010

Setting the language, date, and time

When using the camera for the first time after purchasing, the language, date, and time are cleared. Set the language, date, and time.

1 [ ] screen appears when turning

the camera on.

START MENU

/ LANG.

SET

APress n, o, p, or q to select the

language.

BPress MENU/OK to confirm the setting.

2 Set the date and time.

DATE / TIME NOT SET

2010 2009

YY.MM.DD

SET

APress p or q to select Year, Month,

Day, Hour, or Minute.

BPress n or o to correct the setting.

MEMO

• Holding down n or o changes the numbers

continuously.

• When the time displayed passes “12”, the AM/PM setting changes.

2008

2007 2006

1. 1 12:00 AM

3 Change the date format.

SETNONO

12 / 1 / 2008 10:00

DATE / TIME NOT SET

DD . MM . YY

YY . MM . DD

MM /

DD /

APress p or q to select the date format.

BPress n or o to set the format.

CAlways press MENU/OK after the settings

are completed.

Date format

ex. December 1, 2008 [YY.MM.DD]: [2008.12.1] [MM/DD/YY]: [12/1/2008] [DD.MM.YY]: [1.12.2008]

DATE / TIME NOT SET

DD . MM . YY

MM /

DD /

YY . MM . DD

SET

12 / 1 / 2008 10:00

MEMO

[START MENU] screen also appears when the batteries have been removed and the camera has been left for a long period. Once the batteries have been installed for 30 minutes or more, the camera settings will be retained for roughly 2 hours even if a source of power is removed.

Auto power off function

When the Auto power off function is active, if the camera is left unused for 2 or 5 minutes, this function turns the camera off (➝p.85). To turn the camera back on, press ON/OFF. To play back images, hold down w for about 1 second.

Getting Ready

Turning On and Off

Checking the battery charge

Turn the camera on and check the battery level indicator on the LCD monitor.

AThere is ample battery charge. (Lit white) BThe battery is almost half charged. (Lit white) CThere is insufficient charge left in the battery. The

battery will soon run out. Have a charged battery ready. (Lit red)

DThe battery is depleted. The display will shortly go

blank and the camera will stop working. Replace the battery. (Blinking red)

CAUTION

• Due to the nature of the battery, the battery level

indicator ( , , or V) may appear early when the camera is used in cold locations. Try warming the battery in your pocket or a similar location before use.

• Battery with no remaining charge (V blinking red)

may cause camera faults such as the camera turning itself off without retracting the lens. Always load a fully charged battery.

• Depending on the camera mode, the transition from

to V may occur more quickly.

Correcting the Date and Time

SHOOTING MENU

ISO

QUALITY

AUTO

SET-UP

SET

PLAYBACK VOLUME LCD BRIGHTNESS

BEEP VOLUME SHUTTER VOLUME

DATE / TIME

1 Open the [SET-UP] menu. 2 Display the [DATE/TIME] screen.

SET

DATE / TIME BEEP VOLUME SHUTTER VOLUME PLAYBACK VOLUME LCD BRIGHTNESS

SHOOTING MENU

ISO

QUALITY

SET-UP

AUTO

APress MENU/OK to open the menu.

BPress n or o to select [ SET-UP].

CPress q.

APress p or q to select .

BPress o to move to menu item.

CPress n or o to select [ DATE/TIME].

DPress q.

See “2 Set the date and time. ” (➝p.20).

Getting Ready

Selecting the Language

SHOOTING MENU

AUTO

SET-UP

ISO

QUALITY

AUTO POWER OFF

2 MIN TIME DIFFERENCE VIDEO SYSTEM

NTSC

ENGLISH

SET

FORMAT

/ LANG.

1 Open the [SET-UP] menu. 2 Display the [ ] screen.

ISO

QUALITY

SET-UP

SHOOTING MENU

AUTO

SET

FORMAT

/ LANG. AUTO POWER OFF TIME DIFFERENCE VIDEO SYSTEM

ENGLISH

2 MIN

NTSC

APress MENU/OK to open the menu.

BPress n or o to select [ SET-UP].

CPress q.

APress p or q to select .

BPress o to move to menu item.

CPress n or o to select [ ].

DPress q.

See “1 [ ] screen appears when turning the camera on. ” (➝p.20).

Taking Pictures (AUTO Mode)

This section describes the basic operations.

1 Turn the camera on.

Press ON/OFF down fully to turn the camera on.

Holding the camera correctly

Brace your elbows against your sides and hold the camera with both hands.

Do not cover the lens or flash with your fingers.

CAUTION

• Moving the camera while shooting gives a blurred picture (camera shake). Hold the camera steadily with both hands.

• If the lens or flash is obscured by your fingers or the strap, subjects may be out of focus or the brightness (exposure) of your shot may be incorrect.

Continued Q

Using the Camera

Taking Pictures (AUTO Mode)

AUTO

F4.2

250

F4.2

2 Check the composition on the LCD monitor.

To adjust zoom scale using the Zoom button:

W button

(Zoom out)

Zoom bar

MEMO

•Select e Macro mode to take close-up shots (➝p.47).

• Use digital zoom when you want to shoot the subject closer (➝p.82).

T button

(Zoom in)

• Focal range Approx. 40 cm (1.3 ft.) to infinity

• Optical zoom focal

length (35 mm camera equivalent)

Approx. 38 mm to 113 mm

• Max. zoom scale 3×

3 Focus on the main subject in the AF frame

and press the shutter button down halfway.

AUTO

F4.2

250

F4.2

AF frame AF frame

Halfway pressed

CHECK

• Focus on the subject

Double beep is heard Indicator lamp lit green

• Not focus on the subject

No sound { indicated Indicator lamp blinking green

MEMO

The shutter button has a halfway point at which focus and exposure are automatically optimized before taking the picture by pressing fully down.

becomes smaller and camera focuses on the subject.

CAUTION

F4.2

250

F4.2

When pressing the shutter button halfway, a lens operation sound may be heard.

4 Press the shutter button fully.

Double

beep

Halfway pressed Fully pressed

CAUTION

When taking a picture using the flash, the image may disappear and go dark briefly due to flash charging. The indicator lamp blinks orange during charging.

MEMO

• When the subject is not in the AF frame, use AF/AE lock to take the picture (➝p.29).

• When pressing the shutter button down fully in one motion, the camera takes the picture without the AF frame changing.

Click

Flash

When pressing the shutter button down halfway, b appears on the LCD monitor before the flash fires.

F4.2

250

F4.2

Change the flash mode when you want to take pictures without flash. See p.48 for information on flash.

CAUTION

• The image shown on the LCD monitor before the picture is taken may differ in brightness, color, etc. from the image actually recorded. Play back the recorded image to check it (➝p.32).

• When selecting a slow shutter speed that will cause camera shake, | appears on the LCD monitor. Use flash or a tripod.

• See p.107-110 for information on Warning displays. See “Troubleshooting” (➝p.111-116) for more information.

Continued Q

Using the Camera

Taking Pictures (AUTO Mode)

Z Indicator lamp display

The indicator lamp lights or blinks when pressing the shutter button, etc. The indicator lamp shows the camera status.

Indicator lamp

Display Status

Lit green Locking the focus

Blinking green Camera shake warning, AF warning,

Lit orange Recording to Memory Card or internal

Blinking orange Charging flash (flash will not fire)

Blinking red • Warnings for Memory Card and

or AE warning (ready to shoot)

memory (not ready)

internal memory Card not formatted, incorrect format, memory full, Memory Card or internal memory error

• Lens operation error

MEMO

Detailed warning messages appear on the LCD monitor (➝p.107-110).

Taking pictures with the focus

F4.2

250

F4.2

and exposure locked

In the above composition, the subjects (two people in this case) are not in the AF frame. Pressing the shutter button halfway at this point will result in the subjects being out of focus.

AF/AE lock is useful:

Use AF/AE lock to guarantee best result when shooting a subject that is not suited to autofocusing (➝p.30).

Using AF/AE lock

1 Move the camera slightly so that one of the

subjects is in the AF frame.

2 Press the shutter button down halfway to

focus on the subject.

Double

beep

F4.2

250

Halfway pressed

F4.2

Continued Q

Using the Camera

Taking Pictures (AUTO Mode)

F4.2

250

F4.2

3 Continue to hold the shutter button down

halfway. Move the camera back to the original image and press the shutter button fully.

Click

F4.2

250

F4.2

Fully pressed

MEMO

• AF/AE lock can be applied repeatedly before the shutter is released.

• Use AF/AE lock in all Shooting modes to guarantee excellent results.

• On FinePix J10 / FinePix J12, pressing the shutter button down halfway locks the focus and exposure settings (AF and AE lock).

Subjects not suitable for autofocus

FinePix J10 / FinePix J12 uses a high-precision autofocusing mechanism. However, it may have difficulty focusing on the following:

Very shiny subjects such

Fast moving subjects

as a mirror or car body

• Subjects photographed through glass

• Subjects that do not reflect well, such as hair or fur

• Subjects with no substance, such as smoke or flames

• Dark subjects

• Subjects with little or no contrast between the subject and the background (such as subjects dressed in the same color as the background)

• Shots where another high-contrast object (not the subject) is close to the AF frame and is either closer or further away than your subject (such as a shot of someone against a background with strongly contrasting elements)

For such subjects use AF/AE lock (➝p.29).

+ 102 hidden pages