Franke Foodservice HDCU1318L User Manual
30 1/2"
(78cm)
36 1/2"
(93cm)
15"
(38cm)
12 3/4"
(32cm)
17 3/4"
(45cm)
14" (36cm)
32 1/2"
(83cm)
18" (46cm)
Kindred Commercial Printed in Canada
HDCU1318-□-□-□-□
Heavy Duty Combi Unit
Fixture Specification:
This Heavy Duty Combination Toilet/Lavatory is designed for areas requiring
the utmost in vandal resistance. The fixture is fabricated from heavy 14
gauge type 304 18-10 stainless steel and is designed to withstand loads of
5000lbs (2267kg) without permanent damage. The cabinet and drawn
bowls are seamlessly welded and are polished to a satin finish. The toilet
seat is polished to a sanitary mirror finish. Internal piping is also 14 gauge
type 304 18-10 stainless steel.
Lavatory Oval Bowl (FB x LR x D):
9 1/2" (24cm) x 14 3/4" (38cm) x 5" (13cm)
Toilet
Elongated design blow out jet bowl. The toilet requires a minimum of 35 PSI
flow pressure. The toilet was tested and certified as a low water consumption
toilet using 1.6gpf (6 litres). The trap will pass a 2 1/8" ball and has a seal
of 3.5" min. The waste outlet extends a minimum of 3" behind the fixture
and has a plain end OD of 2 3/8".
The entire fixture is tested and certified to:
ASME A112.19.2-2008/CSA B45.1-08 standards.
HDCU1318C-DV shown
1
2
7
3
8
6
Installation:
These fixtures are designed to be installed onto finished walls which
are serviceable from a pipe chase. Installation is achieved by threading six 1/2"
(13mm) diameter threaded anchor rods to the back of the fixture. The anchor
rods are then secured on the chase side of the wallby means of the supplied nuts
and washers. (Standard included hardware is for walls up to 8" (20cm) thick).
For existing walls, an optional metal cutout template is available. For new
block (CMU) or poured concrete walls, an optional wall sleeve is available.
Available Controls:
The basin is controlled with an air-operated self closing valve with a non-hold
open feature. Flow time is adjustable from approximately 5 to 60 seconds and
has a flow rate of 0.5 gpm (1.9 lpm). The valve is operated by a vandalresistant
pushbutton which requiresless than 5lbs to operate. The valve can be mounted
up to 10 feet (3 meters) away from the push button. Valve conforms to the
requirements of ASME A112.18.1-2005/CSA B125.1-05. See basin valve
options for available configurations.
FIXTURE OVERVIEW:
4
5
Bubbler
1
Integral Soap Dish
2
Toilet Roll Holder
3
Lav Waste Outlet
4
Toilet Waste Outlet
5
Threaded Mounting Locations (6)
6
7
Lav Push Buttons
8
Waste Air Vent
Kindred Commercial Printed in Canada
CANADA
Franke Kindred Canada Limited
1000 Franke Kindred Road, Midland, Ontario, Canada L4R 4K9
email info@franke.com www.kindred-commercial.com
Telephone 1-866-687-7465 Fax 1-800-361-8408
1110 61667
1Please visit www.kindred-commercial.com for the latest specifications.
30 1/2"
(78cm)
36 1/2"
(93cm)
15"
(38cm)
12 3/4"
(
32cm)
17 3/4"
(45cm)
14" (36cm)
321/2"
(83cm)
18" (46cm)
18" (46cm)
17" (43cm)
3" (8cm)
9"
(23cm)
5 1/2"
(14cm)
3 1/2"
(9cm)
3
1/2"
(9cm)
8"
(20cm)
8"
(20cm)
1
"
(3cm)
Finished Floor
Cell Side
4" (10cm)
7
1/4"
(18cm)
15"
(38cm)
22.4"
(57cm)
18.4"
(
47cm)
32.63"
(
83cm)
HDCU1318-□-□-□-□
CHECK ONE BOX PER SECTION
Standard Project Specific Options
Toilet Orientation
Basin Valve
Manifold Valve □ None □ - MV2 Manifold Valve to control 2 fixtures
Bubbler □ Chrome Plated Lead Free Brass
Toilet Roll Holder □ Included
Flush Valve Connection □ None □ - FVC Sloan Royal 603-1.6 (specify wall thickness)
Toilet Waste Outlet □ 2 3/8" OD Plain Outlet
Basin Waste Outlet □ 1 1/2" OD Plain Outlet
Basin Integral Soap Dish □ Included
Suicide Prevention Skirt
□ None □ - SP
Available Installation Elements (ordered separately)
□ HDCU1318L - Left Configuration
□ HDCU1318C - Centre Configuration (as shown)
□ HDCU1318R - Right Configuration
□ - SV Single Temperature Air Operated
□ - DV Hot and Cold Air Operated
Heavy Duty Combi Unit
Wall Sleeve (specify thickness)
□ None □ WS-HDCU1318-A (for walls 3 5/8" thick)
Rods and hardware included for walls
up to 8" (20cm) thick.
□ WS-HDCU1318-B (for walls 5 5/8" thick)
□ WS-HDCU1318-C (for walls 6" thick)
□ WS-HDCU1318-D (for walls 7 5/8" thick)
□ WS-HDCU1318-E (for walls 8" thick)
□ WS-HDCU1318-X (for custom thickness
____________ please specify)
Metal Templates (one per project)
□ None □ MT-HDCU1318
HDCU1318-□-□-□-□
Rough-in Information
APPROVED FOR MANUFACTURE
Customer:
Name and Title (print):
Kindred Commercial Printed in Canada
The latest rough in information is supplied with each fixture. Do not rough in without first verifying dimensions. Franke Kindred Canada reserves the right to make design and specification changes without prior
notice. Franke Kindred Canada will not assume any responsibility for the use of obsolete data. Please visit www.kindred-commercial.com for the latest specifications.
CANADA
Franke Kindred Canada Limited
1000 Franke Kindred Road, Midland, Ontario, Canada L4R 4K9
email info@franke.com www.kindred-commercial.com
Telephone 1-866-687-7465 Fax 1-800-361-8408
Signature:
Date:
Quantity:
Model:
Sleeve or Template # (if required):
Kindred Commercial Printed in Canada
2
Please visit www.kindred-commercial.com for the latest specifications.
1110 61667
Loading...