This motherboard includes two, 184-pin, dual in-line memory module (DIMM)
sockets. You can install corresponding PC 3200 (DDR400), PC 2700
(DDR333), or PC 2100 (DDR266) memory modules. You must install at
least one memory module to ensure normal operation. If you install two
modules, they must be the same speed. Mixing memory modules from
differen t manufacturers is not recommended.
DIMM1
DIMM2
Installation of DDR Memory
1. There is only one gap in the center of the DIMM socket, and the memory
module can be fixed in one direction only. Unlock a DIMM socket by pressing
the module clips outward.
2. Align the memory module to the DIMM socket and insert the module verti-
cally into the DIMM socket.
104
Pins
80
Pins
3. The plastic clips at both sides of the DIMM socket will lock automatically.
14
661M03 Series User Manual
Chapter 2 Installation Instructions
Warning :
Be sure to unplug the AC power supply before adding or remov-
ing expansion cards or other system peripherals, especially the
memory devices, otherwise your motherboard or the system
memory might be seriously damaged.
Memory Qualified Vendor List
The following table lists the Memory modules that have been tested and quali-
fied for use with this motherboard.
Vender Type Size
NanyaPC2100 (DDR 266)128MB
NanyaPC2700 (DDR 333)256MB, 512MB
MicronPC2700 (DDR 333)256MB, 512MB
MicronPC3200 (DDR 400)256MB
WinbondPC2700 (DDR 333)256MB, 512MB
KingstonPC2100 (DDR 266)256MB
KingstonPC2700 (DDR 333)256MB, 512MB
KingstonPC3200 (DDR 400)256MB
A-DATAPC2700 (DDR 333)256MB
TranscendPC2700 (DDR 333)256MB
TranscendPC3200 (DDR 400)256MB
KingMaxPC2100 (DDR 266)128MB, 256MB
KingMaxPC2700 (DDR 333)256MB
TwinMOSPC3200 (DDR 400)512MB
ApacerPC2700 (DDR 333)256MB
HYPC2100 (DDR 266)512MB
661M03 Series User Manual
15
Chapter 2 Installation Instructions
Vender Type Size
HYPC3200 (DDR 400)256M,512M
SamsungPC2100 (DDR 266)128M, 256M
SamsungPC3200 (DDR 400)512M
Note:
Make sure to use only the tested and qualified DDR DIMMS
listed above. Other DDR DIMMs manufactured by other
vendors may not be suitable for this motherboard.
16
661M03 Series User Manual
Chapter 2 Installation Instructions
Power Supply
This motherboard uses an ATX power supply. In order to avoid damaging any
devices, make sure that they have been installed properly prior to connecting
the power supply.
20-pin ATX power connector: PWR1
PWR1 is the ATX power supply connector. Make sure that the power supply cable
and pins are properly aligned with the connector on the motherboard. Firmly plug
the power supply cable into the connector and make sure it is secure.
4-pin ATX_12V Power Connector: PWR2
The ATX power supply connects to PWR2 and provides power to the CPU.
4-pin ATX_12V power connector
43
12V
GND
2
5V
20
12V
GND
1
20-pin ATX power connector
5VGND3.3V GNDGND
-5V GND PS-ON -12V
11
10
12V
PWR_OK3.3V
5VSB
GND
5V
5V
GND 3.3V GND
Attention
You have to press the power button for more than four seconds if
you change the default “Instant Off” setting to “Delay 4 Sec” from
the “Power Button Override” option in the BIOS Power Manage-
ment Setup.
661M03 Series User Manual
1
17
Chapter 2 Installation Instructions
Rear Panel Connectors
This motherboard provides the ports as below:
PS/2 Mouse
1
Connector
PS/2 Keyboard
2
Connector
1
PS/2 Mouse Connector
Serial Port
3
(COM1)
Parallel Port
4
(Printer Port)
VGA Connector
5
7
1394 Port
(optional)
6
LAN connector
8
USB 2.0 Port x 4
This green 6-pin connector is for a PS/2 Mouse.
2
PS/2 Keyboard Connector
This purple 6-pin connector is for a PS/2 keyboard.
3
Serial Port (COM1)
This 9-pin COM1 port is for pointing devices or other serial devices.
4
Parallel Port (Printer Port)
This 25-pin port connects a parallel printer, a scanner, or other devices.
Line-in jack
Line-out jack
Microphone
jack
9
5
VGA Connector
The VGA connector is for output to a VGA-compatible device.
6
USB 2.0 ports
These four Universal Serial Bus (USB) ports are available for connecting USB 2.0/
1.1 devices.
7
1394 port (optional)
This digital interface supports electronic devices such as digital cameras,
scanners and printers.
18
661M03 Series User Manual
Chapter 2 Installation Instructions
8
LAN connector
This port allows connection to a Local Area Network (LAN) through a network hub.
9
Line-in jack, Line-out jack, Microphone jack
When using a two-channel sound source, the Line-out jack is used to connect
to speakers or headphones; the Line-in port connects to an external CD player,
tape player or other audio device. The Microphone jack is used to connect to the
microphone.
Line-in
Line-out
(Front channels)
Microphone
When using a 6-Channel sound source, connect the front speaker to the green
audio output; connect the surround sound speaker to the blue audio input;
connect the center speaker/subwoofer to the red Microphone input, as shown
in the following figure:
Green
Blue
Red
Center
Front Left
Rear Left
661M03 Series User Manual
Front Right
Rear Right
Subwoofer
19
Chapter 2 Installation Instructions
Other Connectors
This motherboard includes connectors for FDD, IDE HDD, USB, CPU/system fan,
and others.
FDD Connector
This motherboard includes a standard FDD connector, supporting 360K, 720K,
1.2M, 1.44M, and 2.88M FDDs.
1
FDD connector
HDD connectors: IDE1 & IDE2
This connectors supports the provided UltraDMA 133/100/66 IDE hard disk
ribbon cable. Connect the cable’s blue connector to the primary (recommended)
or secondary IDE connector, then connect the gray connector to the Ultra DMA
133/100/66 slave device (hard disk drive) and the black connector to the Ultra
DMA 133/100/66 master device. If you install two hard disks, you must configure
the second drive as a slave device by setting its jumper accordingly. Refer to the
hard disk documentation for the jumper settings.
Attention:
Ribbon cables are directional, therefore, make sure to always
connect with the cable on the same side as pin 1 of the IDE1/IDE2
or FDD connector on the motherboard.
20
661M03 Series User Manual
Chapter 2 Installation Instructions
IDE 2
1
IDE 1
Front Panel Connector: F_P1
This motherboard includes one connector for connecting the front panel switch
and LED indicators.
1
+
+
HD-LED
RESET
NC
-
PWR-LED
-
PWR-SW
F_P1
Hard Disk LED Connector (HD-LED)
The connector connects to the case’s IDE indicator LED indicating the activity
status of IDE hard disk.
Reset Switch (RESET)
Attach the connector to the Reset switch on the front panel of the case; the
system will restart when the switch is pressed.
Power LED Connector (PWR LED)
Attach the connector to the power LED on the front panel of the case. The Power
LED indicates the power supply’s status. When the system is in S0 status, the
LED is on. When the system is in S1 status, the LED is blink; When the system
is in S3 or S5 status, the LED is off.
661M03 Series User Manual
21
Chapter 2 Installation Instructions
IrDA Header: IR (optional)
This connector supports wireless transmitting and receiving device. Before using
this function, configure the settings of IR Address, IR Mode and IR IRQ from the
“INTEGRATED PERIPHERALS” section of the CMOS SETUP.
1
+5V
Empty
IRRX
GND
IRTX
IrDA
USB Headers: F_USB 1
Besides four USB ports on the rear panel, the series of motherboards also have
one 10-pin headers on board which may connect to front panel USB cable
(optional) to provide additional two USB ports.
VCC
D4-
D4+
GND
Empty
F_USB 1
VCC
D5-
D5+
GND
NC
22
661M03 Series User Manual
Loading...
+ 74 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.