Ford Thunderbird 2005 User Manual

Download

Introduction 4

Instrument Cluster 10

Warning and control lights 10 Gauges 14

Entertainment Systems 16

AM/FM stereo with in-dash six CD 16

Climate Controls 22

Electronic automatic temperature control 22 Rear window defroster 25

Lights 27

Headlamps 27 Turn signal control 30 Bulb replacement 31

Table of Contents

Driver Controls 38

Windshield wiper/washer control 38 Steering wheel adjustment 39 Power windows 40 Mirrors 41 Speed control 42

Locks and Security 62

Keys 62 Locks 62 Anti-theft system 70

Seating and Safety Restraints 74

Seating 74 Safety restraints 77 Air bags 87 Child restraints 97

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Table of Contents

Tires, Wheels and Loading 109

Tire Information 110 Changing tires 114 Lug Nut Torque 120 Vehicle loading 130 Trailer towing 134 Recreational towing 135

Driving 136

Starting 136 Brakes 139 Traction control/AdvanceTrac 141 Transmission operation 143

Roadside Emergencies 149

Getting roadside assistance 149 Hazard flasher switch 150 Fuel pump shut-off switch 150 Fuses and relays 151 Jump starting 160 Wrecker towing 166

Customer Assistance 167

Reporting safety defects (U.S. only) 175

Cleaning 176

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Table of Contents

Maintenance and Specifications 182

Engine compartment 184 Engine oil 185 Battery 188 Fuel information 196 Air filter(s) 208 Part numbers 209 Refill capacities 210 Lubricant specifications 212

Accessories 217

Index 219

All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Introduction

CALIFORNIA Proposition 65 Warning

WARNING: Engine exhaust, some of its constituents, and

certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

CONGRATULATIONS

Congratulations on acquiring your new Ford Motor Company product. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.

For more information on Ford Motor Company and its products visit the following website:

• In the United States: www.ford.com

• In Canada: www.ford.ca

• In Mexico: www.ford.com.mx

• In Australia: www.ford.com.au

Additional owner information is given in separate publications.

This vehicle’s Owner’s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available.

Remember to pass on this vehicle’s Owner’s Guide when reselling the vehicle. It is an integral part of the vehicle.

Fuel pump shut-off switch: In the event of an accident the

safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emergencies chapter.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Introduction

SAFETY AND ENVIRONMENT PROTECTION

Warning symbols in this guide

How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.

Warning symbols on your vehicle

When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.

Protecting the environment

We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.

BREAKING-IN YOUR VEHICLE

Your vehicle does not need an extensive break-in. Try not to drive continuously at the same speed for the first 1,000 miles (1,600 km) of new vehicle operation. Vary your speed frequently in order to give the moving parts a chance to break in.

Do not add friction modifier compounds or special break-in oils during the first few thousand miles (kilometers) of operation, since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Introduction

SPECIAL NOTICES

Emission warranty

The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.

Service Data Recording

Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may access vehicle diagnostic information through a direct connection to your vehicle when diagnosing or servicing your vehicle.

Event Data Recording

Other modules in your vehicle — event data recorders — are capable of collecting and storing data during a crash or near crash event. The recorded information may assist in the investigation of such an event. The modules may record information about both the vehicle and the occupants, potentially including information such as:

• how various systems in your vehicle were operating;

• whether or not the driver and passenger seatbelts were buckled;

• how far (if at all) the driver was depressing the accelerator and/or the

brake pedal;

• how fast the vehicle was traveling; and

• where the driver was positioning the steering wheel.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Introduction

To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.

Special instructions

For your added safety, your vehicle is fitted with sophisticated electronic controls.

Please read the section Supplemental restraint system (SRS)

in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury.

Front seat mounted rear-facing child or infant seats should

NEVER be placed in front of an active passenger air bag.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Introduction

These are some of the symbols you may see on your vehicle.

Vehicle Symbol Glossary

Safety Alert

Fasten Safety Belt Air Bag-Front

Air Bag-Side Child Seat

Child Seat Installation Warning

Child Seat Tether Anchor

Anti-Lock Brake System

Powertrain Malfunction Speed Control

Master Lighting Switch Hazard Warning Flasher

Fog Lamps-Front Fuse Compartment

See Owner’s Guide

Child Seat Lower Anchor

Brake System

Brake Fluid Non-Petroleum Based

Fuel Pump Reset Windshield Wash/Wipe

Windshield Defrost/Demist

Rear Window Defrost/Demist

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Vehicle Symbol Glossary

Introduction

Power Windows Front/Rear

Child Safety Door Lock/Unlock

Power Window Lockout

Interior Luggage Compartment Release Symbol

Panic Alarm Engine Oil

Engine Coolant

Engine Coolant Temperature

Do Not Open When Hot Battery

Avoid Smoking, Flames, or Sparks

Battery Acid

Explosive Gas Fan Warning

Power Steering Fluid

Maintain Correct Fluid Level

Emission System Engine Air Filter

MAX

MIN

Passenger Compartment Air Filter

Jack

Check fuel cap Low tire warning

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Instrument Cluster

WARNING LIGHTS AND CHIMES

Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.

Emission system/Check engine:

The Check Engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb. Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.

Under engine misfire conditions, excessive exhaust temperatures

could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.

Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Emission system/Check engine warning light to come on. Refer to Fuel Filler Cap in the Maintenance and Specifications chapter.

CHECK

FUEL

CAP

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Instrument Cluster

Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and START, or by applying the parking brake when the ignition is turned to the ON position. If the brake system warning light does not illuminate at this time, seek service immediately from your dealership. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately by your servicing dealership.

Driving a vehicle with the brake system warning light on is

dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehicle checked by your dealer immediately.

Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately. Normal braking is still functional unless the brake warning light also is illuminated.

Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately. A chime will also sound when a malfunction in the supplemental restraint system has been detected.

Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt.

BRAKE

ABS

Charging system: Illuminates when the battery is not charging properly.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Instrument Cluster

Engine oil pressure: Illuminates when the oil pressure falls below the normal range, refer to Engine oil in the Maintenance and Specifications chapter.

Engine coolant temperature:

Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as possible, switch off the engine and let cool. Refer to Engine coolant in the Maintenance and Specifications chapter.

Never remove the coolant reservoir cap while the engine is

running or hot.

Transmission PRNDL indicator:

Displays the gearshift positions. If an “E” character is displayed or flashing, this indicates a transmission malfunction, contact your dealer immediately. Operating the transmission with the “E” character illuminated may cause additional damage to the transmission.

Traction Control娂 active:

Illuminates when the Traction Control娂 is active. If the light remains on, have the system serviced immediately, refer to the Driving chapter for more information.

Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter).

Speed control: Illuminates when the speed control is activated. Turns off when the speed control system is deactivated.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Instrument Cluster

Low washer fluid: Illuminates when the windshield washer fluid is low.

Bulb warning: A text message indicates when one of the exterior front turn lamps or rear brake/turn/tail lamps bulb has burned out. Depress the RESET control to return to the Trip odometer display.

Door ajar: Illuminates when the ignition is in the ON position and any door or trunk is open.

Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators flash faster, check for a burned out bulb.

High beams: Illuminates when the high beam headlamps are turned on.

Electronic throttle control:

Illuminates when the engine has defaulted to a ’limp-home’ operation. Report the fault to a dealer at the earliest opportunity.

Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’s door is opened.

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’s door is opened.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Instrument Cluster

GAUGES

Speedometer: Indicates the current vehicle speed.

Engine coolant temperature gauge: Indicates engine coolant

temperature. At normal operating temperature, the needle will be in the normal range (between “H” and

“C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.

Never remove the coolant reservoir cap while the engine is

running or hot.

Odometer: Registers the total miles (kilometers) of the vehicle.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Trip odometer: Registers the miles (kilometers) of individual journeys. To reset, depress the RESET control. To switch the display from Trip A to the Trip B, depress the A/B control.

Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.

Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade.

Refer to Filling the tank in the

Maintenance and Specifications

chapter for more information.

Instrument Cluster

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Entertainment Systems

AUDIOPHILE SATELLITE READY AM/FM STEREO IN-DASH SIX CD RADIO

1. Seek: Press and release SEEK strong station, selection or track.

2. Rewind: In CD mode, press until desired selection is reached.

Fast forward: In CD mode, press until desired selection is reached.

TEXT: TEXT is only available when equipped with Satellite radio. Your

Audiophile radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your Ford dealer. Detailed Satellite instructions are included with the dealer installed kit.

Dealer installed satellite kit available only in the continental United States.

3. DSP (Digital Signal Processing): Press DSP to access

the Ambiance menu. Ambiance gives the feeling of “being there” to your music, creating increased clarity as well as an open and spacious feel to the music. Press SEL to engage/disengage. Turn the volume control to increase/decrease the level of ambiance.

/ for previous/next

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Entertainment Systems

Occupancy: Press DSP again to change the occupancy mode to optimize sound for ALL SEATS, DRIVER SEAT or TOP DOWN. Press SEL to scroll through settings.

4. Mute: Press to MUTE playing media; press again to return to playing media

5. Eject: Press to eject a CD. Press and hold to eject all loaded discs.

6. Bass: Press BASS; then press SEL the bass output.

Treble: Press TREB; then press SEL the treble output.

7. Select: Use with Bass, Treble, Balance and Fade controls to adjust levels and set the clock.

8. Balance: Press BAL; then press SEL left/right speakers.

Fade: Press FADE; then press SEL rear/front speakers.

9. Menu: Press MENU and SEL to access clock mode, RDS on/off, Traffic announcement mode, Program type mode, and Shuffle mode.

The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend that FM radio broadcasters use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired.

/ to decrease/increase

/ to shift sound to the

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Entertainment Systems

Traffic: Allows you to hear traffic broadcasts. With the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it is broadcasting RDS data).Traffic information is not available in most

U.S. markets.

FIND Program type: Allows you to search RDS-equipped stations for a certain category of music format: Classic, Country, Info, Jazz, Oldies, R&B, Religious, Rock, Soft, Top 40.

Show TYPE: Displays the station’s call letters and format. Shuffle: Press to play tracks in a random order. Press MENU until SHUF

appears in the display. Use SEL to select SHUF DISC, SHUF TRAC or SHUF OFF.

Compression: Brings soft and loud CD passages together for a more consistent listening level. Press MENU until compression status is displayed. Press the SEL control to enable the compression feature when COMP OFF is displayed. Press the SEL control again to disable the feature when COMP ON is displayed.

Setting the clock: Press MENU until SELECT HOUR or SELECT MINS is displayed. Use SEL to manually increase ( hours/minutes. Press MENU again to disengage clock mode.

10. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns.

11. SAT (if equipped): Your Audiophile radio comes equipped with Satellite Ready capability. The kit to enable the Satellite reception is available through your Ford dealer. Detailed satellite instructions are included with the dealer installed kit.

Dealer installed satellite kit available only in the continental United States.

12. AM/FM: Press to select AM/FM frequency band.

Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press and momentarily hold AM/FM. AUTOSET will flash on the display. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Press again to disengage.

) or decrease ( ) the

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Entertainment Systems

13. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels.

Speed sensitive volume: Radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3. Level 0 turns the feature off and level 7 is the maximum setting. Press and hold the volume control for five seconds. Then press SEL to

increase ( appear in the display.

14. Load: Press to load a CD. Press and hold to load up to six discs.

15. CD AUX: Press to access CD or AUX mode.

CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your dealer for further information.

16. Scan: Press SCAN to hear a brief sampling of radio stations or CD tracks. Press again to stop.

17. Disc/Tune: Press manually tune down/up the radio

frequency band, or to listen to the previous/next track on the CD.

CAT: CAT is only available when equipped with Satellite Radio. Your Audiophile radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your Ford dealer. Detailed Satellite instructions are included with the dealer installed kit.

Dealer installed satellite kit available only in the continental United States.

) or decrease ( ) the volume setting. The level will

or to

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Entertainment Systems

For information regarding SIRIUS Satellite Radio, please call toll-free 888-539-SIRIUS (888-539-7474) or visit the SIRIUS website at www.siriusradio.com

RADIO FREQUENCIES

AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are:

AM - 530, 540–1700, 1710 kHz

FM- 87.7, 87.9–107.7, 107.9 MHz

RADIO RECEPTION FACTORS

There are three factors that can effect radio reception:

• Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception.

• Terrain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception.

• Station overload: When you pass a broadcast tower, a stronger signal may overtake a weaker one and play while the weak station frequency is displayed.

CD/CD PLAYER CARE

Do:

• Handle discs by their edges only. Never touch the playing surface.

• Inspect discs before playing. Clean only with an approved CD cleaner

and wipe from the center out.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Entertainment Systems

Don’t:

• Expose discs to direct sunlight or heat sources for extended periods of time.

• Insert more than one disc into each slot of the CD changer magazine.

• Clean using a circular motion.

CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ball point pens may damage CDs. Please contact your dealer for further information.

AUDIO SYSTEM WARRANTY AND SERVICE

Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Climate Controls

DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (DEATC) SYSTEM

1. A/C control: Press to turn on

and manually control the air conditioning. Press again to disengage. Press AUTO for the system to automatically control the temperature.

2. Recirculation control: Press to

engage/disengage. Used to manually enable or disable recirculated air operation. When activated, recirculates air in the cabin thereby reducing the amount of time to cool down the interior of the vehicle. May also help reduce undesired odors from reaching the interior of the vehicle. Will work in all modes except defrost. Recirculation turns off automatically when floor, floor/defrost or defrost mode is selected. To reduce humidity inside the vehicle, turn recirculation off.

3. Passenger side temperature

control: Press to engage the dual zone feature of the DEATC system. Allows the passenger to choose and control a different temperature than the driver, if desired.

4. Rear defrost: Press to defrost

the rear window. Refer to Rear Window Defrostfor more information.

A/C

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Climate Controls

5. DUAL zone selector: Press to

DUAL

toggle the system between single zone and dual zone control.

(Defrost): Distributes outside air through the windshield defroster ducts and the demister outlets. Can be used to clear ice or fog from the windshield. The system will automatically provide outside air to reduce window fogging.

: Distributes air through the windshield defroster ducts, demister

outlets, and the floor ducts. The system will automatically provide outside air to reduce window fogging.

: Distributes air through the floor ducts. The system will

automatically provide outside air to reduce window fogging.

10.

11. OFF: Outside air is shut out and

: Distributes air through the instrument panel, and the floor ducts.

: Distributes air through the instrument panel.

OFF

the fan will not operate.

12. Auto: To engage automatic

AUTO

temperature control, press AUTO and select the desired temperature using the temperature control. The system will automatically determine fan speed, airflow location, AC on or off, and outside or recirculated air, to heat or cool the vehicle to reach the desired temperature.

13. Manual override controls: Allows you to manually select where airflow is directed. To return to full automatic control, press AUTO.

14. Driver’s side temperature control: Controls the temperature on the driver side of the vehicle in dual zone and controls the temperature of the entire vehicle in single zone.

15. Fan Speed: Press to manually increase/decrease fan speed. In manual mode, the display will show

with a bar graph to indicate fan speed. Fan speed can be manually adjusted in AUTO mode. To allow the system to automatically control fan speed, press AUTO.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Climate Controls

16. EXT control: Press to display

EXT

the outside air temperature. Press again to return to interior temperature. Exterior readings are most accurate when the vehicle is moving.

17. Temperature conversion:

F C

Press to toggle between Fahrenheit and Celsius temperature on the DEATC display only. The set point temperatures in Celsius will be displayed in half-degree increments.

OPERATING TIPS

• To reduce fog build up on the windshield during humid weather, place

the air flow selector in the

position.

• To reduce humidity build up inside the vehicle:

Do not drive with the air flow selector in the OFF position. Do not drive with recirculation engaged.

• In order to allow the vehicle to “breathe” using the outside air inlet

vents, do not leave the air flow selector in the OFF position when the vehicle is parked.

• Remove any snow, ice or leaves from the air intake area at the base of

the windshield.

• With the ignition in the OFF position after operating the vehicle, some

vehicle sounds related to the climate control system may be heard.

• Approximately two minutes after key off, the air distribution doors

may adjust their positions as part of the normal operating process.

• Demisters, located at the far left and right sides of the dash, usually

blow out a small amount of airflow in order to reduce side window fogging.

• Outboard panel registers, located at the left and right sides of the

dash, blow out a small amount of airflow when in Floor, Floor/Defrost, and Defrost modes. This also reduces side window fogging.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Climate Controls

• Do not place items over the

climate temperature sensor grid. This may cause improper operation of the system.

To aid in side window defogging/demisting in cold weather:

1. Select

2. Ensure that recirculation is disengaged.

3. Set the temperature control to full heat.

4. Set the fan to the highest speed.

5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the vents

located in the middle of the instrument panel.

REAR WINDOW DEFROSTER

Press the rear window defroster control to clear the rear window of thin ice or fog. The light above the control will illuminate to indicate that the rear defrost is operating.

The ignition must be in the RUN position and the engine running in order to operate the rear window defroster.

The rear window defroster turns off automatically after a predetermined amount of time, if a low battery condition is detected, or if the ignition is turned to the OFF position. To manually turn off the rear window defroster at any time, press the control again.

Do not use razor blades or other sharp objects to clean the inside of the rear window or to remove decals from the inside of the rear window. This may cause damage to the heated grid lines and will not be covered by your warranty.

Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Climate Controls

CABIN AIR FILTER

Your vehicle is equipped with a Cabin air filter. The particulate air filtration system is designed to reduce the concentration of airborne particles such as dust, spores and pollen in the air being supplied to the interior of the vehicle. The particulate filtration system gives the following benefits to customers:

• Improves the customer’s driving comfort by reducing particle

concentration

• Improves the interior compartment cleanliness

• Protects the climate control components from particle deposits

The filter is located just in front of the windshield under the cowl grille on the passenger side of the vehicle.

For more information, or to replace the filter, see your Ford, Lincoln or Mercury Dealer.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Lights

MASTER LIGHTING SWITCH

Turns the lamps off.

Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps.

Turns on the headlamps, parking lamps, instrument panel lamps, license plate lamps and tail lamps.

Autolamp control

The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the master lighting switch.

The autolamp system also keeps the lights on for a preselected period of time after the ignition switch is turned to OFF.

• To turn autolamps on, rotate the

control counterclockwise. The preselected time lapse is adjustable up to approximately three minutes by continuing to rotate the control counterclockwise.

• To turn autolamps off, rotate the control clockwise to OFF.

Note: The instrument panel lamps will only turn on if the autolamp control has determined it is night.

AUTO

Lights

Daytime running lamps (DRL) (Canada Only)

Turns the lowbeam headlamps on with a reduced output.

To activate with automatic transmission:

• the ignition must be in the RUN position;

• the headlamp control is in the OFF position, Parking lamps position,

or Autolamp position when the autolamp function has not turned on the headlamps (daytime); and

• the transmission is out of Park.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Lights

Always remember to turn on your headlamps at dusk or during

inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

High beams

Pull toward you until control stops to activate. Repeat to deactivate.

Flash to pass

Pull toward you slightly to activate and release to deactivate.

PANEL DIMMER CONTROL

Use to adjust the brightness of the instrument panel during parklamp, headlamp and autolamp operation.

• Rotate up to brighten.

• Rotate down to dim.

• Rotate fully up to turn on the

floor and dome lights.

Note: When the headlamp switch is in the autolamp position, the panel dimmer control is only active when the autolamp has determined that it is night.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Lights

The dome light will only go on when the dome light switch is in the delay or ON position.

HEADLAMP VERTICAL AIM ADJUSTMENT

1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away.

• (1) Eight feet

• (2) Center height of lamp to ground

• (3) Twenty five feet

• (4) Horizontal reference line

2. Measure the height from the center of your headlamp to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The center of the lamp is marked by a 3.0 mm circle on the headlamp lens.

3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood.

4. On the wall or screen you will observe a light pattern with flat edges at the top of the beam pattern. If the flat edges are not at the horizontal reference line, the beam will need to be adjusted. To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other.

5. Locate the vertical adjuster on each headlamp, then usea6mmAllen wrench or screwdriver to adjust the headlamp up or down.

6. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE.

7. Close the hood and turn off the lamps.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Lights

TURN SIGNAL CONTROL

• Push down to activate the left turn signal.

• Push up to activate the right turn signal.

INTERIOR LAMPS

Reading and dome lamps

The reading lamps are located in the header trim panel. Press the control next to the reading lamp to activate it.

The reading lamp assembly also contains an overhead dome lamp. This lamp is controlled by the center (OFF) control on the assembly. The dome lamp will stay on if the control is moved to the driver side (ON) position. When the control is in the passenger side (delay) position, the lamp will only come on when a door is opened, or if the panel dimmer control is fully rotated up. If the control is moved to the center position, the lamp will not come on at all.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Lights

BULBS

Replacing exterior bulbs

Check the operation of all of the bulbs periodically.

Using the right bulbs

Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness, pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.

Function Trade number

Park/turn lamps (front) 3457 AK (amber) Supplemental parking lamps (if

equipped) Front side marker lamps 194 Rear side marker lamps 194 Headlamps 9007 Rear stop/turn/tail lamps 3157K Backup lamps 3156K Rear license plate lamps 168 High-mount brake lamp See a dealer or qualified technician Footwell courtesy lamps 168 Reading lamps 3886X Dome lamp 6411 Glove box lamp 168 To replace all instrument panel lights - see your dealer.

912

Interior bulbs

Check the operation of all of the bulbs periodically.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Lights

Replacing headlamp bulbs

To remove the headlamp bulb:

1. Make sure headlamp switch is in

OFF position, then open the hood.

2. Pry up the two retainer pins to

release the headlamp assembly from the vehicle.

3. Remove the nut from the back of

the headlamp and pull headlamp forward.

4. Disconnect the electrical

connector from the bulb by pulling rearward.

5. Remove the bulb retaining ring by

rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Lights

6. Without turning, remove the old

bulb from the lamp assembly by pulling it straight out of the lamp assembly.

To install the new bulb:

Handle a halogen headlamp bulb carefully and keep out of

children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.

1. With the flat side of the new bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly. Turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly. When the grooves are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly.

2. Install the bulb retaining ring over the plastic base and lock the ring by rotating clockwise until it snaps into place.

3. Connect the electrical connector to the bulb.

4. Install the headlamp on vehicle by aligning the lamp on the vehicle, push rearward to fully seat the lamp assembly and install the screw on the headlamp.

5. Push the two retainer pins down.

6. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Lights

Replacing front parking lamp/turn signal bulbs

1. Make sure headlamp switch is in OFF position, then open the hood.

2. Pry up the two retainer pins to release the headlamp assembly from the vehicle.

3. Remove the nut from the back of the headlamp and pull headlamp forward.

4. Rotate bulb socket counterclockwise and remove from lamp assembly.

5. Carefully pull bulb straight out of socket and push in the new bulb.

6. Install bulb socket in lamp assembly by turning clockwise.

7. Install the headlamp on vehicle by aligning the lamp on the vehicle, push rearward to fully seat the lamp assembly and install the screw on the headlamp.

8. Push the two retainer pins down.

9. Turn the lamps on and make sure the new bulb works properly.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Lights

Replacing front/rear side marker bulbs

1. Make sure the headlamp switch is in the OFF position and then remove the screw and carefully pull the lamp assembly out from the bumper.

2. Rotate bulb socket counterclockwise and remove from lamp assembly.

3. Carefully pull bulb straight out of socket and push in the new bulb.

4. To complete installation, follow the removal procedure in reverse order.

Replacing supplemental parking lamp bulbs (if equipped)

1. Make sure the headlamp switch is in the OFF position and then remove the screw and carefully pull the lamp assembly out from the bumper.

2. Rotate the bulb socket counterclockwise and remove from lamp assembly.

3. Pull the bulb straight out of the socket and push in the new bulb.

4. To complete installation, follow the removal procedure in reverse order.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Lights

Replacing tail/brake/turn/backup lamp bulbs

The tail/brake//turn/backup bulbs are located in the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb:

Prior to pulling the carpet away, in step 1, the trunk trim scuff plate must be removed. This can be accomplished by pulling gently on the component until the 6 push pins along the rear of the trunk release. The part can be placed aside and the carpet pulled away. To replace the piece, re-align the pins and push into place.

1. Make sure the headlamp switch is in the OFF position and then open the trunk and carefully pull the carpet away to expose the nut and washer assemblies.

2. Remove the two nut and washer assemblies from the lamp assembly.

3. Pull the lamp assembly towards the rear of the vehicle disengaging the ball stud locator from the ball stud socket in the body. Carefully remove the lamp assembly from the vehicle.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

4. Rotate the bulb socket counterclockwise and remove from lamp assembly.

5. Pull the bulb straight out of the socket and push in the new bulb.

6. To complete installation, follow the removal procedure in reverse order.

Replacing license plate lamp bulbs

1. Make sure the headlamp switch is in the OFF position and then remove two screws and the license plate lamp assembly from the vehicle.

2. Rotate bulb socket counterclockwise and remove from lamp assembly.

3. Carefully pull the bulb from the socket and push in the new bulb.

4. Install the lamp assembly with two screws.

Replacing high-mount brake lamp assembly

For bulb replacement, see a dealer or qualified technician.

Lights

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

MULTI-FUNCTION LEVER

Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.

Windshield washer: Push the end of the stalk:

• briefly: causes a single swipe of the wipers without washer fluid.

• a quick push and hold: the wipers will swipe three times with washer fluid.

• a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.

CHANGING THE WIPER BLADES

1. Pull the wiper arm away from the

vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.

2. Attach the new wiper to the

wiper arm and press it into place until a click is heard.

3. Replace wiper blades every 6

months for optimum performance.

4. Poor wiper quality can sometimes

be improved by cleaning the wiper blades, refer to Window and wiper blades in the Cleaning chapter.

5. To prolong the life of the wiper blades, it is highly recommended to

scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

POWER TILT/TELESCOPE STEERING COLUMN

The steering column can be adjusted manually by moving the four-way rocker adjustment control located below the turn signal/wiper control stalk. Hold the control to adjust.

The telescope function is adjusted by moving the control toward the driver to telescope out and toward the instrument panel to telescope in.

The tilt function is adjusted by moving the control up or down. During easy exit, when you remove the key, the column will move to the

full in and up position. When the key is inserted into the ignition, the column will return to the previous setting.

Never adjust the steering wheel when the vehicle is moving.

AUXILIARY POWER POINT (12VDC)

Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.

The auxiliary power point is located on the instrument panel.

Do not plug optional electrical accessories into the cigarette lighter. Use the power point.

Do not use the power point for operating the cigarette lighter element.

The Maximum power each power point can supply depends on the fuse rating. For example: a 20A fuse should supply a maximum of 240 Watts, a 15A fuse should supply a maximum of 180 Watts and a 10A fuse should supply a maximum of 120 Watts. Exceeding these limits will result in a blown fuse.

Always keep the power point caps closed when not being used.

OFF

PASSENGER AIRBAG

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

POWER WINDOWS

Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure

themselves.

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in

the proximity of the window openings.

Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window.

One touch down

Allows the driver’s window to open fully without holding the control down. Press completely down on AUTO and release quickly. Press again to stop.

Accessory delay

With accessory delay, the window switches, radio, and the convertible top motor, may be used for up to ten minutes after the ignition switch is turned to the OFF position or until either front door is opened.

Short drop glass

In order to improve door efforts and sealing, your vehicle is equipped with short drop glass. This feature lowers the glass when either door is opened. The glass returns to its closed position when the door is closed. If the optional removable top is not installed on your vehicle, this feature will also lower the glass when the convertible top switch is operated. The glass will return to its closed position if the transmission is shifted out of P (Park), or if the opposite door becomes closed.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

Proper operation of the short drop glass requires that the windows be calibrated. Though your windows will have been calibrated before

your vehicle is delivered to you, it is possible for the windows to lose calibration. If a window loses its calibration, your short drop

feature will lower the window, but will not raise it again when the door is closed. To re-calibrate the window, press the up switch to raise the window until it completes its travel and hold the switch down for 2 seconds. Another possible effect of lost calibration is that the feature may not lower the window. To re-calibrate the window in this case, lower the window until it completes its travel and hold the switch down for 2 seconds. Immediately after releasing the window down switch, press the up switch to raise the window until it completes its travel and hold the switch down for 2 seconds.

VISOR MIRROR

To open the visor mirror, slide the mirror cover.

POWER SIDE VIEW MIRRORS

To adjust your mirrors:

1. Select L to adjust the left mirror

or R to adjust the right mirror.

2. Move the control in the direction

you wish to tilt the mirror.

3. Return to the center position to

disable the adjust function.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

LOCKABLE AND ELECTRONIC TRUNK REMOTE CONTROL

The remote trunk release control is located on the driver’s door trim panel and can be operated at any time, except when the security system is armed. This control will not work until the vehicle is disarmed.

You can render the switch inoperable by locking the button with your master key.

In the event of battery failure, you can open the trunk by using your master key on the key cylinder

located behind the driver’s seat.

SPEED CONTROL

With speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h).

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

Setting speed control

The controls for using your speed control are located on the steering wheel for your convenience.

1. Press the ON control and release

it.

2. Accelerate to the desired speed.

3. Press the SET + control and

release it.

4. Take your foot off the accelerator

pedal.

5. The indicator

instrument cluster will turn on.

Note:

• Vehicle speed may vary momentarily when driving up and down a steep hill.

• If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed.

• If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage.

light on the

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

Resuming a set speed

Press the RES control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h).

Increasing speed while using speed control

There are two ways to set a higher speed:

• Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.

Reducing speed while using speed control

There are two ways to reduce a set speed:

• Press and hold the SET - control until you get to the desired speed, then release the control. You can also use the SET control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

• Depress the brake pedal or CANCEL until the desired vehicle speed is reached, press the SET + control.

Turning off speed control

There are two ways to turn off the speed control:

• Depress the brake pedal or press CANCEL. This will not erase your vehicle’s previously set speed.

• Press the speed control OFF control.

Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

Driver Controls

RES

SET

F F

CANCEL

STEERING WHEEL CONTROLS

These controls allow you to operate some audio control features.

Audio control features

Press MEDIA to select AM, FM1, FM2, CD (if equipped) or SAT (if

MUTE

equipped).

VOL

MEDIA

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

In AM, FM1, FM2 or SAT (if equipped) mode:

• Press ⌬ or ⵜ to select preset stations within the selected radio band.

In CD (if equipped) mode:

• Press ⌬ or ⵜ to select the next selection on the CD.

In any mode:

• Press VOL + or − to adjust volume.

Press the PHONE/MUTE control to mute the playing media. Press again to return to the playing media.

MUTE

VOL

MEDIA

MUTE

VOL

MEDIA

MUTE

VOL

MEDIA

HOMELINK姞 WIRELESS CONTROL SYSTEM

The HomeLink威 Wireless Control System, located on the header trim, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of

the way to prevent potential harm or damage.

Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515.

Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.

Programming

Do not program HomeLink威 with the vehicle parked in the garage.

Note: Some vehicles may require the ignition switch to be turned to the

second (or “ACC”) position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal.

1. Press and hold the two outside

buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat step one to program additional hand-held transmitters to the remaining two HomeLink威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink威.

2. Position the end of your hand-held transmitter 1-3 inches (2-8 cm)

away from the HomeLink威 button you wish to program (located on the header trim) while keeping the indicator light in view.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

3. Simultaneously press and hold

both the HomeLink威 and hand-held transmitter button. Do not release

the buttons until step 4 has been completed.

Some entry gates and garage door openers may require you to replace step 3 with procedures noted in the “Gate Operator and Canadian Programming” section for Canadian residents.

4. The indicator light will flash slowly and then rapidly. Release both

buttons when the indicator light flashes rapidly. (The rapid flashing light indicates acceptance of the hand-held transmitters’ radio frequency signals.)

5. Press and hold the just-trained HomeLink威 button and observe the

indicator light. If the light is constant, programming is complete and your device should activate when the HomeLink威 button is pressed and released. Note: To program the remaining two HomeLink威 buttons, begin with step 2 in the “Programming” section — do not repeat step 1.

Note: If the indicator light blinks rapidly for two seconds and then turns to a continuous light, proceed with steps 6 through 8 to complete programming of a rolling code equipped device.

6. At the garage door opener receiver (motor-head unit) in the garage,

locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit).

7. Press and release the “learn” or “smart” button. (The name and color

of the button may vary by manufacturer.)

Note: There are 30 seconds in which to initiate step eight.

8. Return to the vehicle and firmly press, hold for two seconds and

release the HomeLink威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming.

HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with step 2 in the “Programming” section. For questions or comments, please contact HomeLink at www.homelink.com or 1–800–355–3515.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

Gate Operator & Canadian Programming

During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter.

After completing steps 1 and 2 outlined in the “Programming” section, replace step 3 with the following:

Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating.

• Continue to press and hold the HomeLink威 button (note step 3 in the

“Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency

signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.

• Proceed with step 4 in the “Programming” section.

Operating the HomeLink姞 Wireless Control System

To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or

1–800–355–3515.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

Erasing HomeLink姞 buttons

To erase the three programmed buttons (individual buttons cannot be erased):

• Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.

HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with step 2 in the “Programming” section.

Reprogramming a single HomeLink姞 button

To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps:

1. Press and hold the desired HomeLink威 button. Do NOT release the

button.

2. The indicator light will begin to flash after 20 seconds. Without

releasing the HomeLink威 button, follow step 2 in the “Programming” section.

For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

CONVERTIBLE

Articles stored in the convertible top stowage compartment may break the rear glass window when the top is lowered.

Lowering the convertible top

The convertible top can be lowered with the side windows either up or down.

Do not lower the top when the top material is wet.

If you raise and lower the convertible top several times in a row, the motor will heat up, causing the thermal circuit breaker to open so that the top will stop operating. The convertible top will operate again after allowing the motor to cool several minutes.

To lower the convertible top:

1. Bring vehicle to a complete stop. Put the gearshift in the P (Park)

position.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

The convertible top will operate with the key in the RUN position, RUN/ACC position or in the accessory delay mode. It is recommended that the vehicle’s engine is running when lowering the top to prevent draining the battery.

2. Check the convertible top stowage compartment behind the seat to be

sure it is empty and ready to receive the top.

3. Press the button on the

convertible top handle and pull the handle down and forward to release the clamps from the windshield header.

4. Push the convertible top

switch on the instrument panel and hold until the top is completely stored in the stowage compartment.

5. Push the handle back into the lock position.

Installation of the boot (if equipped)

Be sure the boot is tucked into the quarter panel and upper back panel and all snaps are fastened before driving.

1. Fasten the snaps on the boot to

the quarter trim panel on both sides of the vehicle and at the center.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

2. Tuck the boot under the upper

back panel at the rear and the quarter panel along the sides.

3. To remove unfasten the snaps.

4. Pull forward and lift off.

Raising the convertible top

To raise the convertible top:

1. Bring the vehicle to a complete stop. Put the vehicle in the P (Park)

position.

The convertible top will operate with the key in the RUN position, RUN/ACC position or in the accessory delay mode. It is recommended that the vehicle’s engine is running when raising the top to prevent draining the battery.

2. Remove the boot and store it in the luggage compartment.

3. Push the two screws down into

the windscreen panel of your vehicle.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

4. Push the convertible top

switch, holding it until the top unfolds and moves forward toward the windshield header.

5. Press the button on the

convertible top handle and pull the handle down to open both top clamps before the top meets the windshield header.

6. Resume pushing the convertible top switch until it has reached the

fully closed position flush to the header.

7. The two pins under the forward edge of the top should seat

themselves in the matching holes in the header.

8. To fasten both clamps securely,

push the clamp handles into the header on the top until they are flush with the header. Pulling down on the header at the center grip while closing the latches may assist in fastening the clamps. Use the pull cups located on either side of the convertible top handle.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

9. Push the convertible top handle

back up so that it locks into position.

Prolonged storage

It may be difficult to pull down and latch the convertible top after prolonged storage with the top in the down position over the winter or in colder temperatures. This difficulty will decline over time with warmer temperatures and the convertible top in the full up or latched position.

Convertible top and padded molding care

To avoid damage to the cloth top and moldings, use only an approved Ford cleaner, or equivalent. Do not use abrasive material or cleaners.

Wash with a high quality convertible top cleaner/protectant. If your car is equipped with a light colored convertible top, it will require extra care. Do not use abrasive material or cleaners.

Hot waxes applied by automatic car washes can affect the cleanability of cloth material.

Using high water pressure or wand type car washes against the convertible top and windows may cause water leaks and possible seal damage.

Note: Ensure that the convertible top is dry before installing the removable hard top (if equipped) or convertible top staining may occur. Also, high pressure car washes may cause water to enter the convertible top well, which may result in the convertible top staining if the top is not allowed to dry.

REMOVABLE TOP (IF EQUIPPED)

For more information see the CD Rom included with this guide.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

Installing the removable top

The front screw fittings must be checked to see that they are firmly seated after driving a distance of approximately 50 to

60 km (30 to 40 miles).

The removable top does not have the same crush resistance as an integrated steel roof in case of collision or rollover.

The removable top is not, under any circumstances, to be used to carry or support external loads.

Movement of the removable top requires at least two people. The removable top weighs approximately 38 kg (84 lb). Also,

due to its shape, the weight is biased to the rear of the removable top.

Your vehicle must be turned OFF and placed in PARK on a level surface prior to installing or removing the top.

Open the doors, lower the windows, and clean the area where the removable top mounts on the body. Before installing the removable top, unsnap and properly store the convertible top boot. Refer to Installation of the boot in the Convertible section. Also, thoroughly dry the convertible top and then lower.

Note: Before installing the removable top, apply the protective tape to the rear deck of the vehicle, refer to the Quick Reference Guide for instructions.

1. Remove the protective cover from the top. Using a mild detergent,

clean the weather-strips on the top before installing it on the vehicle.

2. Ensure that the removable top levers are rotated rearward to the fully

open position. Lock the wheels on the storage cart, and with the help of at least another person remove the top from the cart.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

Once per year, apply a small amount of silicone lubricant, F5AZ–19553–AA, to the receivers as shown. The lubricant should be sprayed directly into the hole to avoid contaminating the trim parts.

3. Lower the rear of the top into

position so that the pins are placed into the bracket receivers.

4. Position the front of the top so that the locating tabs on each side are

placed in the mounting castings. Ensure that the weather-strip on the top is placed on the body mounted seal without any wrinkles or gaps. The joint should have a smooth and continuous transition to prevent water leaks.

5. Take the mounting key from the bag located in the trunk.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

6. Partially turn, 1/2 turn forward,

the levers of the top (located in the rear on the left and right-hand side of the vehicle).

7. Using the mounting key, loosely

screw in the two screws at the front of the top by two or three turns. The two screws are already located in the windscreen panel of your vehicle.

8. Turn and lock the levers fully

forward. The levers are locked when you feel the spring engage and the levers are pointing toward the front of the vehicle.

Driver Controls

9. Using the mounting key, finish tightening the screws at the front of

the removable top all the way so that they are secure.

The front screw fittings must be checked to see that they are firmly seated after a distance of approximately 50 to 60 km (30

to 40 miles).

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

Removing the top

It is recommended that you prepare the storage rack before removing the top. See Removable top storage rack in this section.

1. Take the mounting key from the bag located in the trunk.

2. Using the mounting key, loosen

the two screws at the front of the top. The two screws remain undetachable in the windscreen panel of your vehicle.

3. Undo the locking levers at the

rear right and left sides of the vehicle. Rotate the levers rearward while applying a slight upward force to the top.

4. With the aid of a second person,

lift the top off the vehicle and store it as described in Removable top storage in the chapter.

5. Push the two screws down into

the windscreen panel of your vehicle.

Removable top storage rack

It is recommended that you prepare the storage rack prior to removing the top from the vehicle.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

1. Remove the storage rack from the package and place the bumper end

of the uprights on the floor with the wheels facing you.

2. Locate the two chrome locking

buttons on each of the two rack legs.

3. Firmly squeeze the two chrome

buttons (top and bottom) on one leg and rotate the leg toward you until the leg snaps into place.

4. Squeeze the second set of chrome

buttons (top and bottom) for the opposite leg until the leg snaps into place.

5. Turn the rack over on its wheels

and place the removable top storage rack on a flat level surface. Make sure the center “T” section is fully locked by attempting to move the section downward without depressing the chrome locking buttons.

6. Lock the two front wheels located

on the ends of each of the two rack legs.

7. To lock the wheels, push down on

the bottom part of the plastic tab located on the tip of each wheel.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

8. Place the removable top on the

storage rack.

9. Make sure the rear edge of the

removable top rests on the rubber bumpers of the rack legs. This prevents damage to the painted edge and the weather-strips.

To unlock the wheels, pull up on the lower portion of the plastic tab located on the tip of each wheel.

Place the mounting key in a safe place to use again. Keep your removable top clean by placing the provided cover over it. If you plan to drive with the convertible top down, ensure all the snaps

on the convertible top boot are fastened and that the rear of the cover is firmly tucked before driving. Refer to Installation of the boot in the Convertible section.

CELL PHONE USE

The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However,

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Driver Controls

drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits.

Mobile Communication Equipment includes, but is not limited to cellular phones, pagers, portable email devices, in vehicle communications systems, telematics devices and portable two-way radios.

A driver’s first responsibility is the safe operation of the vehicle.

The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road. Wait until it is safe to operate Mobile Communications Equipment.

CENTER CONSOLE

Your vehicle may be equipped with a variety of console features. These include:

• Utility compartment

• Cupholders

• Ash tray

Use only soft cups in the cupholder. Hard objects can injure you

in a collision.

POSITIVE RETENTION FLOOR MAT

Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

KEYS

The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer.

You should always carry a second key with you in a safe place in case you require it in an emergency.

Refer to SecuriLock娂 Passive Anti-Theft System for more information.

POWER DOOR LOCKS

Press the top of the control to unlock all doors and the bottom to lock all doors.

When the vehicle’s security system is armed, the power door locks and remote trunk release control are disabled; these features will not work until the security system is disarmed.

Smart locks

With the key in any ignition position:

• The driver’s door will automatically unlock if it is locked by the driver’s power unlock control while the driver’s door is open.

The vehicle may still be locked with the key in the ignition, and performing one of the following actions:

• Pressing the power unlock control on the driver’s door with the doors closed.

• Pressing the power unlock control on the passenger door with the doors closed.

• Operating the remote entry transmitter.

• Operating the driver’s door with a key.

Door key unlocking/locking

Unlocking the doors

Turn the key in the door cylinder to unlock the driver’s door.

The illuminated entry feature will turn on all the interior lamps for 25 seconds or until the ignition is turned to the 4 (RUN) position.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

The inside lights will not turn off if:

• they have been turned on using the dimmer control or

• any door is open.

The battery saver feature will turn off the interior lamps 30 minutes after the ignition is turned to the 2 (OFF) position.

Locking the doors

Turn the key in the door cylinder to lock the driver’s door. Note: Locking the driver’s door using a key does not arm the perimeter alarm.

INTERIOR LUGGAGE COMPARTMENT RELEASE

Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment.

Adults are advised to familiarize themselves with the operation and location of the release handle.

To open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light.

The “T” shaped handle will be located either on the luggage compartment door (lid) or inside the luggage compartment near the tail lamps.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

Keep vehicle doors and

luggage compartment locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles.

On hot days, the temperature in the trunk or vehicle interior can

rise very quickly. Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.

REMOTE ENTRY SYSTEM

This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by:

• weather conditions,

• nearby radio towers,

• structures around the vehicle, or

• other vehicles parked next to your vehicle.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

The remote entry system allows you to:

• unlock the vehicle doors without a key.

• lock all the vehicle doors without a key.

• open the trunk without a key.

• activate the personal alarm.

• arm and disarm the perimeter

anti-theft system.

• operate the illuminated entry feature.

If there is any potential remote keyless entry problem with your vehicle, ensure ALL remote entry transmitters are taken to your authorized dealer to aid in troubleshooting.

Locking the doors

1. Press and release to lock all the doors and activate the anti-theft

system. Note: the turn signal lamps will flash once to confirm the doors, trunk and hood are closed. If any closure is not closed, the turn signals will not flash.

2. Press

doors, trunk and hood are closed. Note: The doors will lock again, and the horn will chirp once.

If any of the doors, the trunk or the hood are not closed, the horn will make two quick chirps and the lights will not flash until the last closure is closed.

and release again within three seconds to confirm that all the

Unlocking the doors

1. Press and release to unlock the driver’s door and deactivate the

perimeter alarm (if activated). Note: The interior lamps will illuminate.

2. Press

doors.

The remote entry system comes with an illuminated entry feature. This feature turns on the interior lamps for 25 seconds or until the ignition is turned to the 4 (RUN) position.

and release again within three seconds to unlock all the

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

The inside lights will not turn off if:

• they have been turned on using the dimmer control or

• any door is open.

The battery saver feature will turn off the interior lamps 30 minutes after the ignition is turned to the 2 (OFF) position.

Opening the trunk

Press once to open the trunk.

• Ensure that the trunk is closed and latched before driving your vehicle. Failure to properly latch the trunk may cause objects to fall out or block the driver’s rear view.

In the event of battery failure, you can open the trunk by using your master key on the key cylinder

located behind the driver’s seat.

Sounding a panic alarm

Press 30 seconds and the turn signal lamps will flash for a maximum of 5

minutes. Press position to deactivate the panic alarm, or wait for the alarm to timeout in

5 minutes.

Note: The panic alarm will only operate when the ignition is in the 1 (LOCK), 2 (OFF) or 3 (ACCESSORY) position.

Replacing the battery

The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent.

to activate the alarm. The horn will sound for a maximum of

or again, or turn the ignition out of the 2 (OFF)

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

To replace the battery:

1. Twist a thin coin between the two

halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.

2. Do not wipe off any grease on the

battery terminals on the back surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when

disposing of transmitter batteries.

4. Insert the new battery. Refer to the diagram inside the remote entry

transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity.

5. Snap the two halves back together.

Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

Replacing lost remote entry transmitters

If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming.

How to reprogram your remote entry transmitters

You must have all remote entry transmitters (maximum of four) available before beginning this procedure.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

To reprogram the remote entry transmitters:

1. Ensure the vehicle is electronically unlocked.

2. Put the key in the ignition.

3. Turn the key from the 1 (LOCK) position to 4 (RUN).

4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK)

position and 4 (RUN). Note: The eighth turn must end in the 4 (RUN) position.

5. The doors will lock, then unlock, to confirm that the programming

mode has been activated.

6. Within 20 seconds press any button on the remote entry transmitter.

Note: If more than 20 seconds have passed you will need to start the procedure over again.

7. The doors will lock, then unlock, to confirm that this remote entry

transmitter has been programmed.

8. Repeat Step 6 to program each additional remote entry transmitter.

9. Turn the ignition to the 1(LOCK) position after you have finished

programming all of the remote entry transmitters.

10. The doors will lock, then unlock, to confirm that the programming

mode has been exited.

Illuminated entry

The interior lamps illuminate when the remote entry system is used to unlock the door(s).

The illuminated entry system will turn off the interior lights if:

• the ignition switch is turned to the 4 (RUN) position, or

• the remote transmitter lock control is pressed, or

• after 25 seconds of illumination.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

The inside lights will not turn off if:

• they have been turned on with the dimmer control, or

• any door is open.

The battery saver will shut off the interior lamps 30 minutes after the ignition has been turned to the 2 (OFF) position.

Autolock

The autolock feature will lock the vehicle’s doors when:

• all the doors are closed,

• the ignition is in the 4 (RUN) position, and

• you shift into forward or reverse, putting the vehicle in motion.

Relock

The autolock feature repeats when:

• either door is opened then closed while the ignition is in the 4 (RUN) position,

• you shift into forward or reverse, and

• you put the vehicle in motion by releasing the brake pedal.

Deactivating/activating autolock

Your vehicle comes with the autolock feature activated. There are two methods to enable/disable this feature: One is through your authorized dealer, and the second is using a power door unlock/lock sequence.

Before following the activation or deactivation procedures, make sure that the anti-theft system is not activated, ignition is off, and the vehicle doors are closed.

Power door unlock/lock procedure

You must complete Steps 1-5 within 30 seconds or the procedure will have to be repeated.

1. Turn the ignition to the 4 (RUN)

position.

2. Press the driver door unlock

control three times.

3. Turn the ignition key from 4

(RUN) to the 2 (OFF) position.

4. Press the driver door unlock control three times.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

5. Turn the ignition back to the 4 (RUN) position. The horn will chirp.

6. Press the unlock control, then press the lock control. The horn will

chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated.

7. Turn the ignition to the 1 (LOCK) or 2 (OFF) position.

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM

SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.

Theft indicator

The theft indicator is the flashing red indicator located on top of the instrument panel.

• When the ignition is in the 2 (OFF) position, the indicator will flash once every 2 seconds if the vehicle is locked and the perimeter alarm is armed.

• When the ignition is in the 4 (RUN) position, the indicator will glow for 3 seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 4 (RUN) position. If this occurs, the vehicle should be taken to an authorized dealer for service.

Automatic arming

The vehicle is armed immediately after switching the ignition to the 1 (LOCK) or 2 (OFF) position.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

Automatic disarming

Switching the ignition to the 4 (RUN) position with a coded key disarms the vehicle.

• The theft indicator will illuminate for three seconds and then go out.

• If the theft indicator stays on for an extended period of time or

flashes rapidly, have the system serviced by your dealer.

Key information

Your vehicle is supplied with two coded keys (or three keys, if the valet feature is available). Only a coded key will start your vehicle.

Spare coded keys may be purchased from an authorized Ford dealer. An authorized Ford dealer can also program your coded key, or you can do it yourself. Refer to Programming spare keys in this chapter.

The following items may prevent the vehicle from starting:

• Large metallic objects.

• Electronic devices on the key chain that can be used to purchase

gasoline or similar items.

• A second key on the same key ring as the coded key.

If any of these items are present, you need to prevent these objects from touching the coded key while starting the engine. These objects cannot damage the coded key, but may cause a momentary “no start” condition if they are too close to the key when starting the engine. If a problem occurs, turn the ignition to the 2 (OFF) position and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Ford coded key.

If your keys are lost or stolen, you will need to do the following:

• Use your spare key to start the vehicle, or

• Have your vehicle towed to an authorized Ford dealer or a locksmith.

The key codes will need to be erased from your vehicle and new codes will need to be re-coded.

Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience.

The correct coded key must be used for your vehicle. The use of the wrong coded key may lead to a “no start” condition.

If an unprogrammed key is used in the ignition, it will cause a “no start” condition.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

Programming spare keys

A maximum of eight keys can be coded to your vehicle. Only Securilock娂 keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure.

If two previously programmed coded keys are not available, you must take your vehicle to an authorized Ford dealer to have the spare coded key(s) programmed.

Please read and understand the entire procedure before you begin.

1. Insert the first previously

programmed coded key into the ignition from 1 (LOCK) to 4 (RUN) (maintain ignition in the 4 (RUN) position for at least three seconds, but no more than ten seconds).

2. Turn the ignition to the 1 (LOCK)

position and remove the first coded key from the ignition.

3. Within ten seconds of turning the ignition to the 1 (LOCK) position,

insert the second previously programmed coded key into the ignition and turn the ignition from the 1 (LOCK) position to the 4 (RUN) position (maintain ignition in the 4 (RUN) position for at least three seconds, but no more than ten seconds).

4. Turn the ignition to the 1 (LOCK) position and remove the second

coded key from the ignition.

5. Within twenty seconds of turning the ignition to the 1 (LOCK)

position, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from 1 (LOCK) to 4 (RUN) (maintain ignition in the 4 (RUN) position for at least three seconds). This step will program your new key to a coded key.

6. To program additional new unprogrammed key(s), wait at least twenty

seconds and then repeat this procedure from Step 1.

If successful, the new coded key(s) will start the vehicle’s engine and the theft indicator will flash on and off. You may repeat Steps 1 through

5. If failure repeats, take your vehicle to your authorized dealer in order

to have new spare key(s) programmed.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Locks and Security

PERIMETER ALARM SYSTEM

The perimeter anti-theft system will warn you in the event of an unauthorized entry to your vehicle.

If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the dealership to aid in troubleshooting.

Arming the system

When armed, this system will respond if unauthorized entry is attempted. When unauthorized entry occurs, the system will flash the turn signal lamps and will sound the horn.

The system is ready to arm whenever the key is removed from the ignition. Either of the following actions will prearm the alarm system:

• Press the

• Press the driver or passenger door lock control while the door is open.

Disarming the system

You can disarm the system by any of the following actions:

• Unlock the doors by pressing the transmitter.

• Unlock the doors with a key. Turn the key full travel (toward the front of the vehicle) to ensure the alarm disarms.

Triggering the anti-theft system

The armed system will be triggered if any door, the trunk or the hood is opened without using the key or the remote entry transmitter.

control on the remote entry transmitter.

control on your remote entry

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

SEATING

Notes:

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.

Adjustable head restraints

Head restraints help to limit head motion in the event of a rear collision. Adjust your head restraint so that it is located directly or as close as possible behind your head.

The head restraints can be moved up and down.

Push control to lower head restraint.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Using the manual lumbar support

The lumbar control is located on the front of the driver’s seat cushion.

Turn to adjust lumbar support.

Using the manual recline function

Never adjust the driver’s seat or seatback when the vehicle is moving.

To maximize restraint system effectiveness, the driver and passenger seat must be in the upright position and the lap belt

must be snug and low across the hips while the vehicle is moving.

To adjust the front seatback using the manual recliner:

• Lift and hold the handle located on the side of the seat.

• Lean against the seatback to adjust it to your desired position. You can recline the seat back or bring it forward.

• Release the handle when the desired position has been reached.

Adjusting the driver’s power seat

Never adjust the driver’s seat or seatback when the vehicle is moving.

Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

To maximize restraint system effectiveness, the driver and passenger seat must be in the upright position and the lap belt

must be snug and low across the hips while the vehicle is moving.

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

The seat position control is located on the outboard side of the seat cushion.

Press front to raise or lower the front portion of the seat cushion.

Press rear to raise or lower the rear portion of the seat cushion.

Press the control to move the seat forward, backward, up or down.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Adjusting the passenger’s power seat

The control is located on the outboard side of the seat cushion.

Press the control to move the seat forward or backward.

Heated seats (if equipped)

To operate the heated seats:

• Push the indicated side of the control for maximum heat.

• Push again to deactivate.

• Push the indicated side of the

control for minimum heat.

• Push again to deactivate.

The heated seat module resets at every ignition run cycle. While the ignition is in the ON position, activating the high or low heated seat switch enables heating mode. When activated, they will turn off automatically when the ignition is turned to the OFF position.

The indicator light will illuminate when the heated seats have been activated.

SAFETY RESTRAINTS

Safety restraints precautions

To maximize restraint system effectiveness, the driver and passenger seat must be in the upright position and the lap belt

must be snug and low across the hips while the vehicle is moving.

To reduce the risk of injury, make sure children sit where they can be properly restrained.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from

injury in a collision.

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag

supplemental restraint system (SRS) is provided.

It is extremely dangerous to ride in a cargo area, inside or

outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.

In a rollover crash, an unbelted person is significantly more likely

to die than a person wearing a safety belt.

Each seating position in your vehicle has a specific safety belt

assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder.

3) Never use a single belt for more than one person.

Combination lap and shoulder belts

Before fastening the safety belt, make sure the shoulder belt passes through the belt holder on the top of the seatback.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.

2. To unfasten, push the release button and remove the tongue from the buckle.

Energy Management Feature

The safety belts in the vehicle are combination lap and shoulder belts.

• This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision.

• This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest.

The safety restraints in the vehicle are combination lap and shoulder belts. The safety belts have two types of locking modes described below.

Vehicle sensitive mode

The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 5 mph (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Automatic locking mode

How to use the automatic locking mode

• Buckle the combination lap and shoulder belt.

• Grasp the shoulder portion and pull downward until the entire belt is pulled out.

• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.

In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt.

The automatic locking mode is not available on the driver safety belt.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

When to use the automatic locking mode

• Anytime a child safety seat is installed in the vehicle. Refer to Safety Restraints for Children or Safety Seats for Children later in this

chapter.

How to disengage the automatic locking mode

Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and return to the vehicle sensitive (emergency) locking mode.

After any vehicle collision, the combination lap and shoulder belt

system at all passenger seating positions must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly, in addition to other checks for proper seat belt system function.

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if

the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly. In addition, all safety belts should be checked for proper function. Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.

Safety belt pretensioner

Your vehicle is equipped with safety belt pretensioners at the driver and front passenger seating positions.

The safety belt pretensioner is a device which removes excess webbing from the safety belt system. The safety belt pretensioner uses the same crash sensor system as the front air bag supplemental restraint system (SRS). When the safety belt pretensioner deploys, webbing from the lap and shoulder belt is tightened. The driver and front passenger seat belt system (including retractors and buckles) must be replaced if the vehicle is involved in a collision that results in deployment of front air bags and safety belt pretensioners. Refer to the Safety belt maintenance section in this chapter.

Failure to replace the safety belt assembly under the above

conditions could result in severe personal injuries in the event of a collision.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Safety belt warning light and indicator chime

The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.

Conditions of operation

If... Then...

The driver’s safety belt is not buckled before the ignition switch is turned to the RUN position...

The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...

The driver’s safety belt is buckled before the ignition switch is turned to the RUN position...

BeltMinder

The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster.

The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.

The safety belt warning light and warning chime turn off.

The safety belt warning light and indicator chime remain off.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

If... Then...

The driver’s safety belt is not buckled before the vehicle has reached at least 3 mph (5 km/h) and 1-2 minutes have elapsed since the ignition switch has been turned to ON...

The driver’s safety belt is buckled while the safety belt indicator light is illuminated and the safety belt warning chime is sounding...

The driver’s safety belt is buckled before the ignition switch is turned to the ON position...

The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data)

Reasons given... Consider...

“Crashes are rare events” 36700 crashes occur every day. The

“I’m not going far” 3of4fatal crashes occur within 25

“Belts are uncomfortable” We design our safety belts to enhance

“I was in a hurry” Prime time for an accident.

The BeltMinder feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until safety belt is buckled.

The BeltMinder feature will not activate.

more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be

seriously injured in a crash during our lifetime.

miles (40 km) of home.

comfort. If you are uncomfortable try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort.

BeltMinder reminds us to take a few seconds to buckle up.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Reasons given... Consider... “Safety belts don’t work” Safety belts, when used properly,

reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks.

“Traffic is light” Nearly 1 of 2 deaths occur in

single-vehicle crashes, many when

no other vehicles are around.

“Belts wrinkle my clothes” Possibly, but a serious crash can do

much more than wrinkle your clothes, particularly if you are unbelted.

“The people I’m with don’t wear belts”

“I have an air bag” Air bags offer greater protection when

“I’d rather be thrown clear” Not a good idea. People who are

Do not sit on top of a buckled safety belt to avoid the Belt

Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.

Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see.

used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers.

ejected are 40 times more likely to DIE. Safety belts help prevent

ejection, WE CAN’T “PICK OUR CRASH”.

One time disable

Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, the BeltMinder will be disabled for that ignition cycle only.

Deactivating/activating the BeltMinder feature

Read steps1-9thoroughly before proceeding with the deactivation/activation programming procedure.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

The BeltMinder feature can be deactivated/activated by performing the following procedure:

Before following the procedure, make sure that:

• The parking brake is set.

• The gearshift is in P (Park).

• The ignition switch is in the OFF position.

• All vehicle doors are closed.

• The driver’s safety belt is unbuckled.

• The parklamps are in OFF position.

To reduce the risk of injury, do not deactivate/activate the Belt

Minder feature while driving the vehicle.

1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.)

2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes.)

• Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated.

3. Buckle then unbuckle the safety belt three times, ending with the

safety belt unbuckled. This can be done before or during BeltMinder warning activation.

4. Turn on the parklamps, turn off the parklamps.

5. Buckle then unbuckle the safety belt three times, ending with the

safety belt unbuckled.

• After step 5 the safety belt warning light will be turned on for three seconds.

6. Within seven seconds of the safety belt warning light turning off,

buckle then unbuckle the safety belt.

• This will disable BeltMinder if it is currently enabled, or enable BeltMinder if it is currently disabled.

7. Confirmation of disabling BeltMinder is provided by the safety belt

warning light flashing four times per second for three seconds.

8. Confirmation of enabling BeltMinder is provided by:

• The safety belt warning light flashing four times per second for three seconds.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

• Followed by three seconds with the safety belt warning light off.

• Once again, the safety belt warning light will flash four times per

second for three seconds.

9. After receiving confirmation, the deactivation/activation procedure is

complete.

Safety belt extension assembly

If the safety belt is too short when fully extended, there is a 8 inch (20 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost.

Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended.

Do not use extensions to change the fit of the shoulder belt across the torso.

Safety belt maintenance

Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if equipped), child safety seat tether bracket assemblies (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.

Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe

personal injuries in the event of a collision.

Refer to Interior in the Cleaning chapter.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

Important supplemental restraint system (SRS) precautions

The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.

Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module.

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag

supplemental restraint system (SRS) is provided.

National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 cm)

between an occupant’s chest and the driver air bag module.

Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.

Steps you can take to properly position yourself away from the air bag:

• Move your seat to the rear as far as you can while still reaching the pedals comfortably.

• Recline the seat slightly (one or two degrees) from the upright position.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Do not put anything on or over the air bag module. Placing

objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury.

Do not attempt to service, repair, or modify the air bag

supplemental restraint system (SRS) or its fuses. See your Ford or Lincoln Mercury dealer.

Modifying or adding equipment to the front end of the vehicle

(including frame, bumper, front end body structure and tow hooks) may affect the performance of the air bag system, increasing the risk of injury. Do not modify the front end of the vehicle.

Children and air bags

For additional important safety information, read all information on safety restraints in this guide.

Children must always be properly restrained. Failure to follow these instructions may increase the risk of injury in a collision.

Air bags can kill or injure a child in a child seat. NEVER place a

rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back and turn the passenger air bag off. Refer to Passenger air bag ON/OFF switch in this chapter of the owner’s guide.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

How does the safety belt pretensioner and air bag supplemental restraint system work?

The safety belt pretensioner and air bag SRS are designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates pretensioner activation and air bag inflation.

The fact that the pretensioners and air bags did not activate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Front air bags and pretensioners are designed to activate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts unless the collision causes sufficient longitudinal deceleration.

The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.

While the system is designed to help reduce serious injuries, contact with a deploying air bag may also cause abrasions, swelling or temporary hearing loss. Because air bags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Several air bag system components get hot after inflation. Do not

touch them after inflation.

If the air bag has deployed, the air bag will not function

again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.

The SRS consists of:

• driver and passenger air bag modules (which include the inflators and air bags)

• side air bags. Refer to Side air bag system later in this chapter

• safety belt pretensioners

• one or more impact and safing sensors

• a readiness light and tone

• and the electrical wiring which connects the components

The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system wiring (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power, the air bag ignitors and safety belt pretensioners.

Determining if the system is operational

The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Air bag readiness section in the Instrument cluster chapter. Routine maintenance of the air bag is not required.

Any difficulty with the system is indicated by one or more of the following:

• The readiness light will either flash or stay lit

• The readiness light will not illuminate immediately after ignition is turned to the RUN position

• A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired.

If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Passenger front and side air bag ON/OFF switch

An air bag ON/OFF switch has been installed in this

vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper

OFF

position in accordance with these instructions and warnings. Failure

PASSENGER AIRBAG

to put the switch in a proper position can increase the risk of serious injury or death in a collision.

Turning the passenger front and side air bags off

1. Insert the ignition key, turn the

switch to OFF position and hold in OFF position while removing the

OFF

key.

2. When the ignition is turned to the

OFF

ON, the passenger airbag OFF light illuminates briefly, momentarily shuts off and then turns back on.

PASSENGER AIRBAG

This indicates that the passenger front and side air bags are deactivated.

If the OFF light fails to illuminate when the front and side

passenger air bag switch is in the OFF position and the ignition switch is in ON, have the front and side passenger air bag switch serviced at your Ford or Lincoln-Mercury dealer.

In order to avoid inadvertent activation of the switch, always

remove the ignition key from the front and side passenger air bag ON/OFF switch.

Turning the front and side passenger air bags back on

The front and side passenger air bags remain OFF until you turn them back ON.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

1. Insert the ignition key and turn the switch to ON.

2. The OFF light will briefly illuminate and then shut off when the ignition is turned to ON. This indicates that the passenger front and side air bags are operational.

PASSENGER AIRBAG

If the OFF light is illuminated when the front and side passenger

air bag ON/OFF switch is in the ON position and the ignition switch is in ON, have the front and side passenger air bag ON/OFF switch serviced at your Ford or Lincoln-Mercury dealer immediately.

The front passenger air bag and the passenger side air bag should always be ON (the air bag OFF light should not be illuminated) unless the passenger is a person who meets the requirements stated either in Category 1, 2 or 3 of the NHTSA/Transport Canada deactivation criteria which follows.

The safety belts for the driver and right front passenger seating

positions have been specifically designed to function together with the air bags in certain types of crashes. When you turn OFF your air bag, you not only lose the protection of the air bag, you also may reduce the effectiveness of your safety belt system, which was designed to work with the air bag. If you are not a person who meets the requirements stated in the NHTSA/Transport Canada deactivation criteria turning OFF the air bag can increase the risk of serious injury or death in a collision.

OFF

Always use safety belts and child restraints properly. If a child in

a rear facing infant seat must be transported in front, the passenger air bag must be turned OFF. This is because the back of the infant seat is too close to the inflating air bag and the risk of a fatal injury to the infant when the air bag inflates is substantial.

The vast majority of drivers and passengers are much safer with an air bag than without. To do their job and reduce the risk of life threatening injuries, air bags must open with great force, and this force can pose a potentially deadly risk in some situations, particularly when a front seat

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

occupant is not properly buckled up. The most effective way to reduce the risk of unnecessary air bag injuries, without reducing the overall safety of the vehicle, is to make sure all occupants are properly restrained in the vehicle, especially in the front seat. This provides the protection of safety belts and permits the air bags to provide the additional protection they were designed to provide. If you choose to deactivate your air bag, you are losing the very significant risk reducing benefits of the air bag and you are also reducing the effectiveness of the safety belts, because safety belts in modern vehicles are designed to work as a safety system with the air bags.

Read all air bag Warning labels in the vehicle as well as the other important air bag instructions and Warnings in this Owner’s Guide.

NHTSA deactivation criteria (excluding Canada)

1. Infant. An infant (less than 1 year old) must ride in the front seat because:

• the vehicle has no rear seat, or

• the vehicle has a rear seat too small to accommodate a rear-facing

infant seat, or

• the infant has a medical condition which, according to the infant’s physician, makes it necessary for the infant to ride in the front so that the driver can constantly monitor the child’s condition.

2. Child age 1 to 12. A child age 1 to 12 must ride in the front seat

because:

• the vehicle has no rear seat, or

• although children ages 1 to 12 ride in the rear seat(s) whenever

possible, children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of the vehicle, or

• the child has a medical condition which, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’s condition.

3. Medical condition. A passenger has a medical condition which,

according to his or her physician:

• causes the passenger air bag to pose a special risk for the passenger and

• makes the potential harm from the passenger air bag in a crash greater than the potential harm from turning OFF the air bag and allowing the passenger, even if belted, to hit the dashboard or windshield in a crash.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

This vehicle has special energy management safety belts for the

driver and right front passenger. These particular belts are specifically designed to work with air bags to help reduce the risk of injury in a collision. The energy management safety belt is designed to give or release additional belt webbing in some accidents to reduce concentration of force on an occupant’s chest and reduce the risk of certain bone fractures and injuries to underlying organs. In a crash, if the air bag is turned OFF, this energy management safety belt might permit the person wearing the belt to move forward enough to incur a serious or fatal injury. The more severe the crash, and the heavier the occupant, the greater the risk is. Be sure the air bag is turned ON for any person who does not qualify under the NHTSA deactivation criteria.

Transport Canada deactivation criteria (Canada Only)

1. Infant: An infant (less than 1 year old) must ride in the front seat because:

• my vehicle has no rear seat, or

• the rear seat in my vehicle cannot accommodate a rear-facing infant

seat, or

• the infant has a medical condition which, according to the infant’s physician, makes it necessary for the infant to ride in the front seat so that the driver can monitor the infant’s condition.

2. Child age 12 or under: A child age 12 or under must ride in the

front seat because:

• my vehicle has no rear seat, or

• although children age 12 and under ride in the rear seat whenever

possible, children age 12 and under have no option but to sometimes ride in the front seat because rear seat space is insufficient, or

• the child has a medical condition that, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can monitor the child’s condition.

3. Medical condition: A passenger has a medical condition that,

according to his or her physician:

• poses a special risk for the passenger if the air bag deploys and

• makes the potential harm from the passenger air bag deployment

greater than the potential harm from turning OFF the air bag and experiencing a crash without the protection offered by the air bag

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

This vehicle has special energy management safety belts for the

Side air bag system

Do not place objects or mount equipment on or near the air bag

cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying air bag. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.

Do not use accessory seat covers. The use of accessory seat

covers may prevent the deployment of the side air bags and increase the risk of injury in an accident.

Do not lean your head on the door. The side air bag could injure

you as it deploys from the side of the seatback.

Do not attempt to service, repair, or modify the air bag SRS, its

fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer.

All occupants of the vehicle should always wear their safety belts

even when an air bag SRS is provided.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

How does the side air bag system work?

The side air bag system consists of the following:

• An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks.

• A special seat cover designed to allow air bag deployment.

• The same warning light, electronic control and diagnostic unit as used for the front air bags.

• Two crash sensors located under the outboard side of the front seats, attached near the floor.

Side air bags, in combination with seat belts, can help reduce the risk of severe injuries in the event of a significant side impact collision.

The side air bags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the air bag on the side affected by the collision will be inflated, even if the respective seat is not occupied. The air bag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions.

The air bag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.

The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Side air bags are designed to inflate in side-impact collisions, not roll-over, rear-impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration.

Several air bag system components get hot after inflation. Do not touch them after inflation.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

If the side air bag has deployed, the air bag will

not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If

the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.

Determining if the system is operational

Any difficulty with the system is indicated by one or more of the following:

• The readiness light (same light as used for front air bag system) will either flash or stay lit.

• The readiness light will not illuminate immediately after ignition is turned to the RUN position.

• A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired.

Disposal of air bags and air bag equipped vehicles (including pretensioners)

See your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel.

SAFETY RESTRAINTS FOR CHILDREN

See the following sections for directions on how to properly use safety restraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Important child restraint precautions

You are required by law to use safety restraints for children in the U.S. and Canada. If small children (generally children who are four years old or younger and who weigh 40 lbs [18 kg] or less) ride in your vehicle, you must put them in safety seats made especially for children. Many states require that children use approved booster seats until they are eight years old. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle.

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from

injury in a collision.

Always follow the instructions and warnings that come with any infant or child restraint you might use.

Children and safety belts

If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts.

Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle.

If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit.

Do not leave children, unreliable adults, or pets unattended in your vehicle.

Child booster seats

Children outgrow a typical convertible or toddler seat when they weigh 40 pounds (18 kg) and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly, which could increase the risk of serious injury.

To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably. Booster seats also make the shoulder belt fit better and more comfortably for growing children.

When children should use booster seats

Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly. Generally this is when they weigh about 80 lbs (36 kg) (about 8 to 12 years old).

Booster seats should be used until you can answer YES to ALL of these questions:

• Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching?

• Does the lap belt rest low across the hips?

• Is the shoulder belt centered on the shoulder and chest?

• Can the child stay seated like this for the whole trip?

Types of booster seats

There are two types of belt-positioning booster seats:

• Those that are backless.

If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Seating and Safety Restraints

• Those with a high back.

A backless booster would be a better choice because the high back booster will place the child closer to the instrument panel and airbag.

Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs (18 kg).

The shoulder belt should cross the chest, resting snugly on the center of the shoulder. The lap belt should rest low and snug across the hips, never up high across the stomach.

If the booster seat slides on the vehicle seat, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.

The importance of shoulder belts

Using a booster without a shoulder belt increases the risk of a child’s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only. It is best to use a booster seat with lap/shoulder belts.

Follow all instructions provided by the manufacturer of the booster seat.

Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of

the body and may increase the risk of injury or death in a collision.

Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a

collision.

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats

Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the

100

REVIEW COPY 2005 Thunderbird (tbr), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Ford Thunderbird 2005 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints