Ford Thunderbird 2002 User Manual

Page 1
Table of Contents
Introduction 4
Instrument Cluster 8
Warning and control lights 8 Gauges 14
Entertainment Systems 16
AM/FM stereo with CD 16
Climate Controls 30
Electronic automatic temperature control 30
Lights 43
Headlamps 43 Turn signal control 46 Bulb replacement 46
Driver Controls 54
Windshield wiper/washer control 54 Steering wheel adjustment 55 Power windows 56 Mirrors 58 Speed control 59
Locks and Security 76
Keys 76 Locks 76 Anti-theft system 77
Seating and Safety Restraints 87
Seating 87 Safety restraints 90 Air bags 100 Child restraints 113
1
Page 2
Table of Contents
Driving 125
Starting 125 Brakes 129 Traction control 131 Transmission operation 133 Vehicle loading 139 Trailer towing 141
Roadside Emergencies 145
Getting roadside assistance 145 Hazard flasher switch 146 Fuel pump shut-off switch 146 Fuses and relays 147 Changing tires 156 Jump starting 161 Wrecker towing 167
Customer Assistance 168
Reporting safety defects (U.S. only) 177
Cleaning 178
Maintenance and Specifications 184
Engine compartment 186 Engine oil 187 Battery 190 Fuel information 199 Air filter(s) 211 Part numbers 216 Refill capacities 216 Lubricant specifications 218
2
Page 3
Table of Contents
Accessories 223
Index 225
All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.
Copyright © 2002 Ford Motor Company
3
Page 4
Introduction
CALIFORNIA Proposition 65 Warning
WARNING: Engine exhaust, some of its constituents, and
certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
CONGRATULATIONS
Congratulations on acquiring your new Ford Motor Company product. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle the greater the safety and pleasure you will derive from driving it.
For more information on Ford Motor Company and its products visit the following website:
In the United States: www.ford.com
In Canada: www.ford.ca
In Mexico: www.ford.com.mx
In Australia: www.ford.com.au
Additional owner information is given in separate publications.
This Owner’s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available.
Remember to pass on the Owner’s Guide when reselling the vehicle. It is an integral part of the vehicle.
Fuel pump shut-off switch In the event of an accident the
safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside emergencies chapter.
4
Page 5
Introduction
SAFETY AND ENVIRONMENT PROTECTION
Warning symbols in this guide
How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
Warning symbols on your vehicle
When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Protecting the environment
We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.
BREAKING-IN YOUR VEHICLE
There are no particular guidelines for breaking-in your vehicle. During the first 1,600 km (1,000 miles) of driving, vary speeds frequently. This is recommended to give the moving parts a chance to break in.
SPECIAL NOTICES
Emission warranty
The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owners Guide.
5
Page 6
Introduction
These are some of the symbols you may see on your vehicle.
Vehicle Symbol Glossary
Safety Alert
Fasten Safety Belt Air Bag-Front
Air Bag-Side Child Seat
Child Seat Installation Warning
Child Seat Tether Anchor
Anti-Lock Brake System
Traction Control AdvanceTrac
Master Lighting Switch Hazard Warning Flasher
Fog Lamps-Front Fuse Compartment
See Owner’s Guide
Child Seat Lower Anchor
Brake System
Brake Fluid ­Non-Petroleum Based
Fuel Pump Reset Windshield Wash/Wipe
Windshield Defrost/Demist
6
Rear Window Defrost/Demist
Page 7
Vehicle Symbol Glossary
Introduction
Power Windows Front/Rear
Child Safety Door Lock/Unlock
Power Window Lockout
Interior Luggage Compartment Release Symbol
Panic Alarm Engine Oil
Engine Coolant
Engine Coolant Temperature
Do Not Open When Hot Battery
Avoid Smoking, Flames, or Sparks
Battery Acid
Explosive Gas Fan Warning
Power Steering Fluid
Maintain Correct Fluid Level
Emission System Engine Air Filter
MAX
MIN
Passenger Compartment Air Filter
Jack
Check fuel cap Low tire warning
7
Page 8
Instrument Cluster
WARNING LIGHTS AND CHIMES
Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicles functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have
the respective system inspected immediately.
Check engine
Illuminates briefly to ensure the system is functional. If it comes on after the engine is started, one of the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted and will not require towing.
Light turns on solid:
Temporary malfunctions may cause your light to illuminate. Examples are:
The vehicle has run out of fuel.
Poor fuel quality or water in the fuel.
The fuel cap may not have been properly installed and securely
tightened.
These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the fuel cap. After three driving cycles without these or any other temporary malfunctions present, the light should turn off. (A driving cycle consists of a cold engine startup followed by mixed city/highway driving.) No additional vehicle service is required.
8
Page 9
Instrument Cluster
If the light remains on, have your vehicle serviced at the first available opportunity.
Light is blinking:
Engine misfire is occurring which could damage your catalytic
converter.
You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
Check fuel cap
Illuminates when the fuel cap is not installed correctly. Check the fuel cap for proper installation. When the fuel filler cap is properly re-installed, the light(s) will turn off after a period of normal driving. Continuing to operate the vehicle with the check fuel cap light on, or a mis-installed fuel cap can activate the Service Engine Soon/Check Engine warning light.
It may take a long period of time for the system to detect an improperly installed fuel filler cap.
For more information, refer to Fuel filler cap in the Maintenance and specifications chapter.
CHECK
FUEL
CAP
Brake system warning
To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position (alternatively for some vehicles when the ignition is moved from the ON position to START position, the light will momentarily illuminate prior to reaching the START position). It also illuminates if the parking brake is engaged. If the brake system warning light does not illuminate as described, seek service immediately. Illumination after the parking brake is released indicates low brake fluid
BRAKE
P!
9
Page 10
Instrument Cluster
level or a brake system malfunction and the brake system should be serviced immediately by a qualified technician. Refer to Brakes in the Driving chapter for more information.
Anti-lock brake system (ABS)
To confirm the anti-lock brake system (ABS) warning light is functional it will momentarily illuminate when the ignition is turned to the ON position (alternatively for some vehicles when the ignition is moved from the ON position to the START position, the light will momentarily illuminate just prior to reaching the START position). If the light remains on, continues to flash or fails to illuminate, have the ABS serviced immediately. If the ABS light remains on, it means the anti-lock brake system has malfunctioned and is disabled, however, the normal brake system will still function unless the brake warning light also remains illuminated and parking brake is off. Refer to Brakes in the Driving chapter for more information.
Transmission PRNDL indicator
Displays the gearshift positions. If an Echaracter is displayed or flashing, this indicates a transmission malfunction, contact your dealer immediately. Operating the transmission with the Echaracter illuminated may cause additional damage to the transmission.
ABS
Air bag readiness
Illuminates to confirm that the air bags (front and side) are operational. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately.
10
Page 11
Instrument Cluster
Safety belt
Illuminates to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter.
Engine coolant temperature
Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as safely possible, switch off the engine and let it cool.
Never remove the coolant recovery cap while the engine is
running or hot.
Refer to Engine coolant in the Maintenance and specifications chapter. If light stays on or continues to turn on after the vehicle warms up, have your vehicle serviced.
Engine oil pressure
Illuminates when the oil pressure falls below the normal range. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and specifications chapter.
Charging system
Illuminates when the battery is not charging properly.
Traction Controlactive
Illuminates when the Traction Controlsystem is active. It will be lit for a minimum of four seconds or for the duration of the Traction Controlevent.
For more information, refer to the Driving chapter.
11
Page 12
Instrument Cluster
Low fuel
Illuminates when the fuel level in the fuel tank is at or near empty, refer to Fuel gauge in this chapter for more information.
Speed control
Illuminates when the speed control is activated.
Low washer fluid
Illuminates when the windshield washer fluid is low.
Turn signal
Illuminates when the turn signals or the hazard lights are turned on. If the lights stay on continuously or flash faster, check for a burned-out bulb.
Bulb Warning
Illuminates when one of the exterior bulbs has burned out.
High beams
Illuminates when the high beam headlamps are turned on.
12
Page 13
Instrument Cluster
Door ajar
Illuminates when any door or the trunk is open.
Safety belt warning chime
Sounds to remind you to fasten your safety belts.
BeltMinderchime
Sounds intermittently to remind you to fasten your safety belts.
Supplemental restraint system (SRS) warning chime
Sounds when a malfunction in the supplemental restraint system (front or side airbags) has been detected. Have the supplemental restraint system inspected immediately.
Headlamps on warning chime
Sounds when the headlamps or parking lamps are on, the key is removed from the ignition and the drivers door is opened.
Key-in-ignition warning chime
Sounds when the key is left in the ignition and the driver’s door is opened.
Turn signal chime
Sounds when the turn signal lever has been activated to signal a turn and not turned off after the vehicle is driven more than 0.8 km (1/2 mile).
13
Page 14
Instrument Cluster
GAUGES
Engine coolant temperature gauge
Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the Hand C); if the needle goes above the normal range, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool. Refer to
Engine coolant in the Maintenance and specifications chapter.
Never remove the coolant reservoir cap while the engine is
running or hot. Steam and scalding liquid from a hot cooling system can burn you badly.
This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate.
14
Page 15
Fuel gauge
Displays approximately how much fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade.
When refueling the vehicle from an empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel.
Speedometer
Indicates the current vehicle speed.
Odometer
Registers the total kilometers (miles) of the vehicle.
Trip odometer
Registers the kilometers (miles) of individual journeys. To reset, depress the control.
Instrument Cluster
To switch the display from Trip A to the Trip B feature, depress the A/B control.
Tachometer
Indicates the engine speed in revolutions per minute.
Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
15
Page 16
Entertainment Systems
AUDIOPHILE AM/FM STEREO IN DASH SIX CD RADIO
1. Seek control
2. Rewind/Fast forward control
3. DSP control
4. Phone/mute control
5. Eject control
6. Bass/treble control
7. Select control
8. Balance/fade control
9. Menu control
Volume/power control
Press the control to turn the audio system on or off. Turn the control to raise or lower volume.
16
10. Radio preset controls
11. CD control
12. AM/FM control
13. ON/OFF and volume control
14. Load control for CDs
15. Shuffle control
16. Scan control
17. Tune control
PUSH ON
Page 17
Entertainment Systems
If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a nominallistening level when the ignition switch is turned back on.
Speed sensitive volume
With this feature, radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise.
The recommended level for speed sensitive volume is from level 1 through level 3. Level 0 turns the speed sensitive volume off and level 7 is the maximum setting.
To engage the speed sensitive volume feature, press and hold the volume control for five seconds (with the radio on), then press:
PUSH ON
to increase volume
compensation.
to decrease or shut off the
SEL
volume compensation.
The selected level will appear in the display.
AM/FM select
The AM/FM select control works in radio and CD modes.
AM FM
CD
AM/FM select in radio mode
This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
AM/FM select in CD mode
Press this control to stop CD play and begin radio play.
Tune/disc adjust
The tune control works in radio or CD mode.
17
Page 18
Entertainment Systems
Tune adjust in radio mode
Press frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly.
Press a listenable station is located there). Hold for quick movement.
Disc adjust for CD mode
Press disc. (Play will begin on the first track of the disc unless shuffle mode is engaged.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs.
Press through the remaining discs.
Seek function
The seek function works in radio or CD mode.
Seek function in radio mode
Press listenable station down the frequency band. SEEK DOWN will display.
Press SEEK UP will display.
Seek function in CD mode
Press track of the current disc. If the beginning of the disc is reached, the CD player seeks to the beginning of the last track on the current disc and begins playing.
Press the last track has been completed, the first track of the current disc will automatically replay.
to move to the next
DISC
TUNE
to move to the next frequency up the band (whether or not
to select the previous
DISC
TUNE
to select the next disc. Hold the control to fast-forward
to find the next
to find the next listenable station up the frequency band.
to seek to the previous
to seek forward to the next track of the current disc. After
18
Page 19
Entertainment Systems
Scan function
The scan function works in radio or CD mode.
Scan function in radio mode
Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
Scan function in CD mode
Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the control again.
Radio station memory preset
The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2).
Setting memory preset stations
1. Select the frequency band with the AM/FM select control. Press the
AM/FM control to toggle between AM, FM1, or FM2.
2. Press the SEEK control to access the next listenable station up or
down the frequency band. Press the TUNE control to go up or down the listening band in individual increments.
3. Select a station. Refer to Seek function for more information on
selecting a station.
4. Press and hold a memory preset control. The playing media will mute
momentarily. When the sound returns, the station is held in memory on the control you selected. The display will read SAVED.
Autostore
Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations.
19
Page 20
Entertainment Systems
Starting autostore
1. Press and momentarily hold the AM/FM control.
2. AUTOSET will flash in the display
as the frequency band is scrolled through.
3. When the six strongest stations are filled, the station stored in
memory preset control 1 will start playing. If there are fewer than six strong stations available on the frequency
band, the remaining memory preset controls will all store the last strong station available.
To deactivate autoset and return to your audio systems manually set memory stations, press the AM/FM control again.
CD select
CD mode may be entered by pressing the CD control and the LOAD control. Load the CD into the audio system. The first track of the disc will begin playing. After that, CD play will begin where it stopped last.
If an alternative CD is desired, press the corresponding preset control (1–6) of a loaded CD, or press the TUNE control to access the other loaded CDs.
NO CD will display if the CD control is activated when there is not a CD present in the audio system.
If the CD control is pressed followed by with a preset number and that particular slot is empty, NO CD will display and the system will begin to play the next available disc.
CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ball point pens may damage CDs. Please contact your dealer for further information.
AM FM
AM FM
CD
CD
20
Page 21
Entertainment Systems
Display description
Six circles are always lit in the digital display. These signify the six CD slots in the audio system. When a disc is loaded into a particular slot (1–6), the number inside that specific circle lights. If the circle is empty, there is no CD in that particular slot.
Load
The load feature allows you to load single CDs into the player internal to the radio.
This six disc CD player is equipped with a CD door. Compact discs should only be inserted into the player after the CD door has been opened by the player. Do not attempt to force the door open. Compact discs should only be loaded by pressing the LOAD control.
Press the LOAD control. (You can choose which slot will be loaded by pressing the desired preset number. If you do not choose a slot, the system will choose the next available one.) Wait until the CD door opens. Load the CD into the player. LOADING CD# is displayed. When the CD has been loaded, the door will close and the CD will begin to play. For example, to load a CD into slot 2, press the LOAD control and then press preset 2.
Auto load
This feature allows you to autoload up to 6 discs into the multi disc CD player internal to the radio.
Press and hold the LOAD control until AUTOLOAD # is displayed. The CD door will open. Load the desired discs, one at a time. The CD is loaded into position and the audio system will display CD#. Each time the CD door opens, INSERT CD# is displayed. The door will close and the player will move to the next slot after each disc has been loaded. The process is repeated until all 6 slots are full. The audio system plays the last CD loaded and the display is updated. If some slots are already full and autoload is activated, the system will fill all empty slots.
LOAD
LOAD
21
Page 22
Entertainment Systems
Eject
Press the EJ control to stop and eject a CD. You can choose which CD will be ejected by pressing the EJ control and the desired preset number (1–6). For example, to eject CD 2, press the EJ control and then press the preset 2 control. If you do not choose a specific CD, the player will eject the current CD.
If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD. This feature may be used when the ignition is ON or OFF.
Auto eject
Press and momentarily hold the EJ control to engage auto eject. All CDs which are present in the player will be ejected one at a time. If a CD is ejected and not removed from the door of the CD player, the player will automatically reload the CD. This feature may be used when the ignition is ON or OFF.
Rewind
The rewind control works in CD modes.
Press and hold the REW control until the desired selection is reached. If the beginning of the disc is reached, the CD will begin play at the first track. Release the control to disengage rewind mode.
When in rewind mode, your audio system will automatically lower the volume level of the playing media.
EJ
EJ
REW FF
Fast forward
The fast forward control works in CD modes.
REW FF
Press and hold the FF control until the desired selection is reached. If the end of the disc is reached, the CD will return to the first track. Release the control to disengage fast forward mode.
When in fast forward mode, your audio system will automatically lower the volume level of the playing media.
22
Page 23
Entertainment Systems
Shuffle feature
Press the SHUF control until the desired shuffle mode is displayed. The audio system will then engage the desired shuffle mode.
When engaged, the shuffle feature has two different modes: SHUFFLE DISC and SHUFFLE TRK.
SHUFFLE DISC randomly plays tracks from all the discs presently in the audio system.
SHUFFLE TRK plays all the tracks on the current disc in random order.
Compression feature
The compression feature operates in CD mode and brings soft and loud CD passages together for a more consistent listening level.
Press the MENU control until compression status is displayed. Press the SEL control to enable the compression feature when COMPRESS OFF is displayed. Press the SEL control again to disable the feature when COMPRESS ON is displayed.
MENU
+
SEL
Bass adjust
The bass adjust control allows you to increase or decrease the audio systems bass output.
Press the BASS control. Use the SEL control to increase or decrease the amount of bass.
Treble adjust
The treble adjust control allows you to increase or decrease the audio systems treble output.
Press the TREB control. Use the SEL control to increase or decrease the amount of treble.
BASS
TREB
BASS
TREB
+
+
SEL
SEL
23
Page 24
Entertainment Systems
Speaker balance adjust
Speaker sound distribution can be adjusted between the right and left speakers.
Press the BAL control. Use the SEL control to adjust the sound between the left and right speakers.
Speaker fade adjust
Speaker sound can be adjusted between the front and rear speakers.
Press the FADE control. Use the SEL control to adjust the sound between the front and rear speakers.
Menu mode
The MENU control allows you to access many different features within your audio system. There are three sets of menus available depending upon which mode or feature is activated.
While in FM mode, two menus are available. If RDS is turned OFF, you can access the following:
SELECT HOURS Refer to Setting the clock.
SELECT MINUTES Refer to Setting the clock.
RDS OFF Refer to Radio data system feature.
If RDS is turned ON, you can access the following:
TRAFFIC ON/OFF-Refer to Traffic announcements.
FIND type-Refer to Program type.
SHOW (NAME, TYPE, NONE)- Refer to Radio data system feature.
RDS ONRefer to Radio data system feature.
SELECT HOURS Refer to Setting the clock.
SELECT MINUTES Refer to Setting the clock.
When in CD mode, you can access: SELECT HOURS, SELECT MINUTES or COMP ON/OFF.
BAL
FADE
BAL
FADE
+
+
SEL
SEL
24
Page 25
Entertainment Systems
SELECT HOURS, SELECT MINUTESAllows you to adjust the hours and minutes. Refer to Setting the clock.
TRAFFIC ON/OFFTraffic announcements can be programmed as local or distant. Refer to Traffic announcements.
RDS ON/OFFThis feature allows your audio system to receive text information from RDS-equipped FM radio stations. Refer to Radio Data
System feature.
FIND type Allows you to select your desired FM program type and search for that selection.
SHOW Allows you to select from NAME (displays the name of the radio station), TYPE (displays the RDS program type: rock, jazz, etc.), or NONE (deactivates the RDS display).
Radio data system (RDS) feature
This feature allows your audio system to receive text information from RDS-equipped FM radio stations.
To activate RDS:
When in FM mode, press the MENU control until RDS OFF displays.
Press the SEL control to engage this feature (RDS ON).
RDS features:
Once the RDS feature is on, press the MENU control to scroll through the following selections:
Traffic announcements
This feature allows you to hear traffic announcements while in CD mode. These announcements are broadcast by traffic capable RDS stations.
When in this mode, traffic announcements will interrupt radio and CD play.
Press the MENU control until TRAFFIC is displayed.
Press the SEL control to engage the feature. The display will read
TRAFFIC ON.
This feature also allows you to control the volume of traffic announcements. With the display reading TRAFFIC ON, adjust the volume using the volume control to the desired level. The volume level will show at the bottom of the display. Interrupting traffic announcements will be at the selected volume level.
MENU
+
SEL
25
Page 26
Entertainment Systems
To disengage the feature, press the MENU control until TRAFFIC ON displays. Press the SEL control. The display will read TRAFFIC OFF.
Traffic announcements are not available in most U.S. markets.
Program type
This feature allows you to search for RDS stations selectively by their program type.
Press the MENU control until FIND program type is displayed.
Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections:
Classic
Country
Info
Jazz
Oldies
R&B
Religious
Rock
Soft
To p 40
Show
This feature allows you to select the type of RDS broadcast information the radio will regularly show in the display.
MENU
MENU
+
+
SEL
SEL
With RDS activated, press the MENU control until SHOW is displayed.
MENU
+
SEL
Use the SEL control to select TYPE (displays the RDS program type: rock, jazz, etc), NAME (displays the name of the radio station) or NONE (deactivates the RDS display).
Digital signal processing
The digital signal processing (DSP) feature allows you to change the signal mode to suit your listening tastes.
26
Page 27
Entertainment Systems
Press the DSP control to access the DSP menu. Press the SEL control to enter one of the following modes:
DSP OFF
SIGNAL MODE
OCCUPANCY MODE
Use the SEL control to select the desired signal mode (the selected mode will appear in the display). The following signal modes can be selected:
DSP OFFdisengages the feature
NEWS—”voice-onlytype of sound with a limited audio band
JAZZ CLUBjazz club with clearly reflected sounds
HALLrectangular concert hall capacity of about 2 000
CHURCHchurch with a high vault
STADIUMoutdoor stadium with a capacity of about 30 000
Press the DSP control again to access the occupancy modes. Use the SEL control to optimize the sound based upon the occupants in the vehicle. The following occupancy modes can be selected:
ALL SEATS
DRIVER SEAT
TOP DOWN
DSP
+
SEL
SEL
Mute mode
Press the control to mute the playing media. Press the control again to return to the playing media.
Setting the clock
Press the MENU control until SELECT HOUR or SELECT MINUTE is displayed. (The menu mode must be engaged to enable clock mode).
27
Page 28
Entertainment Systems
Use the SEL control to manually set the time.
Press hours/minutes.
Press hours/minutes.
Press the MENU control again to disengage the clock mode.
CLEANING COMPACT DISCS
Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion.
CD CARE
Handle discs by their edges only. Never touch the playing surface.
Do not expose discs to direct sunlight or heat sources for extended
periods of time.
CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ball point pens may damage CDs. Please contact your dealer for further information.
to increase
to decrease
SEL
RADIO FREQUENCY INFORMATION
The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are:
AM 530, 540–1600, 1610 kHz
FM 87.7, 87.9–107.7, 107.9 MHz
Not all frequencies are used in a given area.
28
Page 29
Entertainment Systems
RADIO RECEPTION FACTORS
Three factors can affect radio reception:
Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by signal modulation.Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.
Terrain. Hills, mountains and tall buildings between your vehicles antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its shadow) returns your reception to normal.
Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed.
The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo.
AUDIO SYSTEM WARRANTIES AND SERVICE
Refer to the Warranty Guide for audio system warranty information.
If service is necessary, see your dealer or a qualified technician.
29
Page 30
Climate Controls
DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM
1. A/C control
2. Windshield defrost control
3. Recirculated air control
4. Passenger temperature control
5. Rear defrost control
6. Heated wiper rest/windshield control
7. Windshield and floor control
8. Floor control
9. Panel and floor control
10. Panel control
11. OFF control
12. AUTO control
13. Driver temperature control
14. Fan speed control
15. Temperature conversion control
16. Exterior temperature control
30
Page 31
Climate Controls
Your vehicle is equipped with a Dual Automatic Temperature Control (DATC) system. The system will maintain a selected temperature and automatically control air flow.
You can override the automatic operation with any of the override controls.
The dual temperature zone feature allows the driver and front passenger to set their own independent temperature set points for individual comfort. The system uses common controls for air distribution and fan speed for both driver and passenger.
Turning the DATC system on, single zone control
Press AUTO, any of the override controls, the fan speed control, or the driver temperature selection control to turn the DATC system on in the single zone control. While in single zone control the driver and passenger set temperatures are equalized, and only the drivers set temperature is displayed. The DATC system will only operate when the ignition is in the RUN position.
31
Page 32
Climate Controls
Turning the DATC system on, dual zone control
Press the passenger temperature control to turn the DATC system on in dual zone control. While in dual zone control, independent temperatures are maintained for both the driver and passenger, and both set temperatures are displayed.
Turning the system off
Press OFF. The outside temperature (EXT) function (if selected) will continue to operate until the ignition is turned off.
EXT
F C
AUTO
OFF
DATC automatic operation
Press AUTO and select the desired temperature. The selected
EXT
temperature will appear in the display window, and an indicator
F C
above the AUTO control will light. The DATC system will either heat or cool the vehicle to achieve the selected temperature. The system
AUTO
OFF
will automatically determine the fan speed, airflow location and whether outside or recirculated air is required.
32
F
Page 33
Climate Controls
When in AUTO and weather conditions require heat, the DATC directs the majority of the airflow to the floor area. The system will allow some airflow out of the defroster, demister outlets and outer instrument panel registers in order to reduce window fogging. Additionally, if the engine is not warm enough to provide heat, the fan will operate at a low speed and the airflow will be directed to the windshield or to the floor. In approximately 3 and the airflow location will change to the floor area.
When in AUTO mode, the DATC system automatically controls the air conditioning operation, the fan speed, the airflow direction and determines whether outside or recirculated air is required. Manual control of the A/C, air recirculation and fan speed are available in auto mode.
If unusual conditions exist (i.e. window fogging), the manual override controls allow you to select airflow locations as necessary. To return to full automatic control, press the AUTO control.
DATC system AUTO temperature balance
1
⁄2minutes or less, the fan speed will start to increase
AUTO
EXT
F F
F C
OFF
A/C
R
The AUTO control may be used to toggle between single zone control and dual zone control.
When in dual zone control (both driver and passenger set temperatures are displayed), press and hold the auto control for approximately two seconds to equalize the passenger set temperature with the driver set temperature. Only the driver set temperature will be displayed. This feature is useful when the driver is alone in the vehicle.
33
Page 34
Climate Controls
When in single zone control (only driver set temperature displayed), press and hold the AUTO control for approximately two seconds to
EXT
F
F C
return the DATC system to dual zone control. Independent driver and passenger temperatures will be maintained. The previous passenger
AUTO
OFF
set temperature and the current driver set temperature are displayed.
Driver side temperature selection
AUTO
EXT
F F
F C
OFF
A/C
R
The display window indicates the selected temperature and manual control of fan speed (
) if automatic fan speed is not desired.
To control the temperature, select any temperature between 19°C (65°F) and 29°C (85°F) by pressing the temperature control on the driver side of the system.
For continuous maximum cooling, press the temperature control until 16°C (60°F) is shown in the display window. The DATC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature is selected by pressing the temperature control.
For continuous maximum heating, press the temperature control until 32°C (90°F) is shown in the display window. The DATC will continue maximum heating (disregarding the displayed temperature) until a cooler temperature is selected by pressing the temperature control.
34
Page 35
Passenger side temperature selection
To control the temperature, select any temperature between 19° C (65° F) and 29° C (85° F) by pressing the temperature control on the passenger side of the system.
Temperature conversion
Press the Fahrenheit/Celsius (°F °C) control to switch between Fahrenheit and Celsius temperature on the DATC display only. The set point temperatures in Celsius will be displayed in half-degree increments.
Climate Controls
A/C
F
EXT
F C
AUTO
OFF
R
C
,
Fan speed (
AUTO
)
OFF
EXT
F C
A/C
F F
R
When AUTO is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, press the fan control to cancel the automatic fan speed operation. Press the control up for higher fan speed or down for lower
fan speed. The display will show
and a bar graph to indicate manual
fan speed operation and relative speed.
35
Page 36
Climate Controls
When the fan is adjusted in the AUTO mode, the AUTO indicator will remain lit and the system will remain in auto operation.
To return to automatic fan operation, press AUTO. The fan icon and bars will disappear from the display, and the DATC system will return to full automatic operation.
A/C control
A/C
(air conditioning) Used to manually enable or disable the operation of the air conditioning in all modes except defrost. In all modes, the air conditioning will only function if the outside temperature is about 2°C (35°F) or higher. When manual A/C is selected (ON) the indicator will be lit. When manual A/C is selected (OFF) the indicator will not be lit.
In defrost and floor/defrost mode, if the outside temperature is about 2°C (35°F) or higher, the air conditioner will automatically dehumidify the air to reduce window fogging. However, the A/C indicator will be off and the A/C override control cannot be selected.
When AUTO is selected, the A/C operates automatically for existing conditions. With automatic A/C operation, the A/C indicator will be lit if the outside temperature is about 2°C (35°F) or higher. You may override the automatic A/C operation at any time. To manually control the A/C operation and cancel automatic A/C operation, press the A/C control. When the A/C is manually controlled in the AUTO mode, the AUTO indicator will remain lit. To return to automatic A/C operation, press AUTO.
AUTO
EXT
F F
F C
OFF
A/C
R
Recirculation control
(air recirculation) Used to manually enable or disable the operation of the recirculated air operation in all modes except defrost. The use of recirculated air when the air conditioning is operating helps to reduce the amount of time to cool down the interior of the vehicle in
36
Page 37
Climate Controls
very hot conditions. Recirculated air may also help to keep undesired outside odors from reaching the vehicle interior. It is recommended to allow the DATC system to automatically control the selection of outside or recirculated air.
The recirculation control cannot be selected in the defrost mode, as interior fogging may occur.
In floor and floor/defrost modes, the DATC system will automatically return to outside air to help reduce window fogging. When the recirculation air control is selected, the amount of time in manual recirculated air depends on the ambient temperature.
When AUTO is selected, the recirculated air feature operates automatically for existing conditions. You may override the automatic recirculated air operation at any time. To manually control the recirculated air operation and cancel automatic recirculated air operation, press the recirculated air control. When the recirculated air is manually controlled in the AUTO mode, the AUTO indicator light will remain lit. To return to full automatic recirculated air operation, press AUTO.
Do not leave the DATC system in recirculated air operation for extended periods of time while the system is in a heating mode or in cold/damp conditions as this may cause interior fogging of the front, side and rear windows.
Manual override controls
AUTO
EXT
F F
F C
OFF
A/C
R
The manual override controls allow you to manually determine where airflow is directed. To return to fully automatic control, press AUTO.
When a manual airflow override control is selected, the DATC system will turn off the AUTO indicator and display the indicators of all operating override controls. More than one override control indicator may turn on when an override control is selected.
37
Page 38
Climate Controls
The air conditioning compressor can operate in all modes except OFF. However, the air conditioning will only function if the outside temperature is about 2°C (35°F) or higher.
Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle.
Airflow direction control
(panel) Distributes air through the instrument panel.
(panel/floor) Distributes air through the instrument panel and the front floor ducts. For added customer comfort, the air distributed through the floor ducts may be slightly warmer than the air sent to the instrument panel registers.
(floor) Distributes air through the front floor ducts. The system will allow some airflow out the defroster ducts, the demister outlets and outer instrument panel registers.
(floor/defrost) Distributes air through the windshield defroster ducts, the demister outlets and the front floor ducts. The system will allow some airflow out of the outer instrument panel registers. For added customer comfort, the air distributed through the floor ducts may be slightly warmer than the air sent to the windshield defroster ducts. If the outside temperature is about 2°C (35°F) or higher, the air conditioner will automatically dehumidify the air to reduce window fogging. (Note that the A/C indicator does not illuminate when this mode is selected.) Recirculation and A/C override controls can be selected.
(defrost) Distributes outside air through the windshield defroster ducts and the demister outlets. It can be used to clear ice or fog from the windshield. The system will allow some airflow out of the outer instrument panel registers. If the outside temperature is about 2°C (35°F) or higher, the air conditioner will automatically dehumidify the air to reduce window fogging. Recirculation and A/C override controls cannot be selected. Note that the A/C indicator does not illuminate
when this mode is selected.
Turn DATC off
OFF-Outside air is kept out. The fan, heating and air conditioning will not operate. The outside temperature will still display when selected with the ignition in the RUN position.
38
Page 39
Climate Controls
Electric window heaters
(heated wiper rest) Located at the base of the windshield, this feature heats the front glass area below the area heated by the front defroster where the windshield wipers sit in their parked position. When activated, the feature keeps the wiper blades warm and reduces the chance of ice build up on the blades. The indicator will light when the feature is in operation.
With the ignition in RUN and the engine running, the feature will be automatically enabled if the temperature is below 5°C (40°F). The feature can be manually selected or deselected at any time. However, the automatic feature will be enabled each time the engine is started.
In cold, dry conditions where wet snow or ice is not present it is acceptable to manually deselect the operation of this feature.
The feature will run continuously unless a low battery condition is detected, or unless the feature is manually deselected, and will only activate when the vehicle engine is running (to prevent excessive drain of the vehicle battery).
R
(rear window defroster) Refer to Rear Window Defroster.
Displaying outside temperature
AUTO
EXT
EXT TEMP
F
F C
OFF
A/C
R
Press EXT to display the outside air temperature. It will remain selected until the EXT control is pressed again.
If the driver or passenger temperature or the fan speed is changed, or the AUTO or
modes selected while the outside temperature is displayed, the driver and passenger temperature display will be displayed for 4 seconds. Following this, the outside temperature display will return to the window.
If the outside temperature is displayed while the DATC system is in the OFF mode and the DATC is turned on, the driver and passenger
39
Page 40
Climate Controls
temperatures will be displayed for 4 seconds. Following this, the outside temperature display will return to the window.
The outside temperature reading is most accurate when the vehicle is moving. Higher readings may be obtained when the vehicle is not moving. The readings may not agree with temperatures given on the radio due to differences in vehicle and station locations.
Operating tips
R
In humid weather, select
and
reduce fogging on your windshield. After a few minutes, select any desired position.
To prevent humidity buildup inside the vehicle, dont drive with the
climate control system in the OFF position.
DO NOT leave the DATC system in recirculated air mode for extended
periods of time while the system is in a heating mode or in cold or damp conditions as this may cause interior fogging of the front, side and rear windows.
Do not place objects under the front seat that will interfere with the
airflow.
Remove any snow, ice or leaves from the air intake area at the base of
the windshield.
If your vehicle has been parked with the windows closed during hot
weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Then operate the air conditioner as you would normally.
If the air conditioner works well with the recirculation feature on, but
not in the outside air mode, this may indicate that the cabin air filter needs to be replaced.
Do not place objects over the defroster outlets. These objects can
block airflow and reduce your ability to see through your windshield. Also, avoid placing small objects on top of your instrument panel. These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system.
before driving. This will
40
Page 41
Climate Controls
Do not place items over the climate temperature sensor grid. This may
cause improper operation of the DATC system.
With the ignition in the OFF position after operating the vehicle, some
vehicle sounds related to the climate control system may be heard.
Approximately two minutes after key off, the air distribution doors
may adjust their positions as part of the normal operating process.
To aid in side window defogging/demisting in cold weather conditions:
1. Select
2. Set the temperature control to full heat
3. Select A/C
4. Set the fan speed to High
5. Direct the outer panel vents towards the side windows
6. In order to increase the airflow to the outer panel vents, close the central panel vents.
Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.
41
Page 42
Climate Controls
REAR WINDOW DEFROSTER
Press the rear window defroster control to clear the rear window of thin ice or fog. The indicator will illuminate when the rear window defroster is selected.
The ignition must be in the RUN position and the engine running in order to operate the rear window defroster.
The rear window defroster turns off automatically after 10 minutes or sooner if a low battery condition is detected, or when the ignition is turned to the OFF position. To manually turn off the rear window defroster before 10 minutes have passed, push the control again.
CABIN AIR FILTER
Your vehicle is equipped with a cabin air filter. This particulate air filtration system is designed to reduce the concentration of airborne particles such as dust, spores and pollen in the air being supplied to the interior of the vehicle. The particulate filtration system gives the following benefits to customers:
Improves the customers driving comfort by reducing particle
concentration
Improves the interior compartment cleanliness
Protects the climate control components from particle deposits
The filter is located just in front of the windshield under the cowl grille on the passenger side of the vehicle.
For more information, or to replace the filter, contact your Ford, Lincoln or Mercury Dealer.
R
42
Page 43
Lights
MASTER LIGHTING SWITCH
Rotate the headlamp control to the first position to turn on the parking lamps.
Rotate to the second position to turn on the headlamps.
Autolamp control
The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the master lighting switch.
The autolamp system also keeps the lights on for a preselected period of time after the ignition switch is turned to OFF.
To turn autolamps on, rotate the
control counterclockwise. The preselected time lapse is adjustable up to approximately three minutes by continuing to rotate the control counterclockwise.
To turn autolamps off, rotate the control clockwise to OFF.
AUTO
AUTO
Daytime running lamps (DRL) (Canada Only)
Turns the lowbeam headlamps on with a reduced output.
To activate with automatic transmission:
the ignition must be in the RUN position;
the headlamp control is in the OFF position, Parking lamps position,
or Autolamp position when the autolamp function has not turned on the headlamps (daytime); and
the transmission is out of Park.
43
Page 44
Lights
Always remember to turn on your headlamps at dusk or during
inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
High beams
Pull toward you until control stops to activate. Repeat to deactivate.
Flash to pass
Pull toward you slightly to activate and release to deactivate.
INT
OFF
INT
AUTO
PANEL DIMMER CONTROL
Use to adjust the brightness of the instrument panel during parklamp, headlamp and autolamp operation.
Rotate up to brighten.
Rotate down to dim.
Rotate fully up to turn on the
interior lights.
44
Page 45
Lights
HEADLAMP VERTICAL AIM ADJUSTMENT
1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen directly in front of it.
(1) Eight feet
(2) Center height of lamp to ground
(3) Twenty five feet
(4) Horizontal reference line
2. Measure the height from the center of your headlamp to the ground and mark a 2.4 meter (8 foot) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The center of the lamp is marked by a 3.0 mm circle on the headlamp lens.
3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood.
4. On the wall or screen you will observe a light pattern with flat edges at the top of the beam pattern. If the flat edges are not at the horizontal reference line, the beam will need to be adjusted.
5. Locate the vertical adjuster on each headlamp, then usea6mm allen wrench or screwdriver to adjust the headlamp up or down.
6. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE.
7. Close the hood and turn off the lamps.
45
Page 46
Lights
TURN SIGNAL CONTROL
Push down to activate the left turn signal.
Push up to activate the right turn signal.
INTERIOR LAMPS
Map lamps
The map lamps and controls are located on the rearview mirror. Press the controls on the bottom of the mirror to activate the lamps.
INT
OFF
INT
AUTO
BULBS
Replacing exterior bulbs
Check the operation of the following lamps frequently:
Headlamps
Tail lamps
Brakelamps
High-mount brakelamp
Turn signal lamps
Supplemental parking lamps
Front/rear side marker lamps
Backup lamps
License plate lamp
Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance.
46
Page 47
Lights
Using the right bulbs
Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized D.O.T.for North America and an Efor Europe to assure lamp performance, light brightness, pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
Function Number of bulbs Trade number
Park/turn lamps (front)
Supplemental parking lamps (if equipped)
Front side marker lamps
Rear side marker lamps
Headlamps 2 9007 Rear stop/turn/tail
lamps Backup lamps 2 3156K Rear license plate
lamps High-mount brake
lamp Footwell courtesy
lamps Map lamps 2 575 Glove box lamp 1 168 To replace all instrument panel lights - see your dealer.
2
2
4
2
2
2
See a dealer or qualified technician
2
3457 AK (amber)
912
194
194
3157K
168
168
Interior bulbs
Check the operation of the following interior bulbs frequently:
front map lamps
For bulb replacement, see a dealer or qualified technician.
47
Page 48
Lights
Replacing headlamp bulbs
To remove the headlamp bulb:
1. Make sure headlamp switch is in
OFF position, then open the hood.
2. Pry up the two retainer pins to
release the headlamp assembly from the vehicle.
3. Remove the screw from the back
of the headlamp and pull headlamp forward.
4. Disconnect the electrical
connector from the bulb by pulling rearward.
5. Remove the bulb retaining ring by
rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb.
48
Page 49
Lights
6. Without turning, remove the old
bulb from the lamp assembly by pulling it straight out of the lamp assembly.
To install the new bulb:
Handle a halogen headlamp bulb carefully and keep out of
childrens reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.
1. With the flat side of the new bulbs plastic base facing upward, insert the glass end of the bulb into the lamp assembly. Turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly. When the grooves are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly.
2. Install the bulb retaining ring over the plastic base and lock the ring by rotating clockwise until it snaps into place.
3. Connect the electrical connector to the bulb.
4. Install the headlamp on vehicle by aligning the lamp on the vehicle, push rearward to fully seat the lamp assembly and install the screw on the headlamp.
5. Push the two retainer pins down.
6. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again.
49
Page 50
Lights
Replacing front parking lamp/turn signal bulbs
1. Make sure headlamp switch is in OFF position, then open the hood.
2. Pry up the two retainer pins to release the headlamp assembly from the vehicle.
3. Remove the screw from the back of the headlamp and pull headlamp forward.
4. Rotate bulb socket counterclockwise and remove from lamp assembly.
5. Carefully pull bulb straight out of socket and push in the new bulb.
6. Install bulb socket in lamp assembly by turning clockwise.
7. Install the headlamp on vehicle by aligning the lamp on the vehicle, push rearward to fully seat the lamp assembly and install the screw on the headlamp.
8. Push the two retainer pins down.
9. Turn the lamps on and make sure the new bulb works properly.
50
Page 51
Lights
Replacing front/rear side marker bulbs
1. Make sure the headlamp switch is in the OFF position and then remove the screw and carefully pull the lamp assembly out from the bumper.
2. Rotate bulb socket counterclockwise and remove from lamp assembly.
3. Carefully pull bulb straight out of socket and push in the new bulb.
4. To complete installation, follow the removal procedure in reverse order.
Replacing supplemental parking lamp bulbs (if equipped)
1. Make sure the headlamp switch is in the OFF position and then remove the screw and carefully pull the lamp assembly out from the bumper.
2. Rotate the bulb socket counterclockwise and remove from lamp assembly.
3. Pull the bulb straight out of the socket and push in the new bulb.
4. To complete installation, follow the removal procedure in reverse order.
51
Page 52
Lights
Replacing tail/brake/turn/backup lamp bulbs
The tail/brake//turn/backup bulbs are located in the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb:
Prior to pulling the carpet away, in step 1, the trunk trim scuff plate must be removed. This can be accomplished by pulling gently on the component until the 6 push pins along the rear of the trunk release. The part can be placed aside and the carpet pulled away. To replace the piece, re-align the pins and push into place.
1. Make sure the headlamp switch is in the OFF position and then open the trunk and carefully pull the carpet away to expose the nut and washer assemblies.
2. Remove the two nut and washer assemblies from the lamp assembly.
3. Pull the lamp assembly towards the rear of the vehicle disengaging the ball stud locator from the ball stud socket in the body. Carefully remove the lamp assembly from the vehicle.
4. Rotate the bulb socket counterclockwise and remove from lamp assembly.
5. Pull the bulb straight out of the socket and push in the new bulb.
6. To complete installation, follow the removal procedure in reverse order.
52
Page 53
Replacing license plate lamp bulbs
1. Make sure the headlamp switch is in the OFF position and then remove two screws and the license plate lamp assembly from the vehicle.
2. Rotate bulb socket counterclockwise and remove from lamp assembly.
3. Carefully pull the bulb from the socket and push in the new bulb.
4. Install the lamp assembly on liftgate with two screws.
Replacing high-mount brake lamp assembly
For bulb replacement, see a dealer or qualified technician.
Lights
53
Page 54
Driver Controls
WINDSHIELD WIPER/WASHER CONTROLS
Rotate the windshield wiper control to the desired interval, low or high speed position. The ignition must be in the ACC or RUN position to operate the windshield wiper.
The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.
Push the control on the end of the stalk to activate washer. Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use.
Speed dependent wipers
When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicles speed changes.
Windshield wiper blades
Check the wiper blades for wear at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades.
Checking the wiper blades
If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent. Rinse thoroughly with clean water. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
54
Page 55
Driver Controls
Changing the wiper blades
To replace the wiper blades:
1. Pull the wiper arm away from the windshield and lock into the service position.
2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
3. Attach the new wiper to the wiper arm and press it into place until a click is heard.
TILT/TELESCOPE STEERING COLUMN
Power tilt/telescope steering column
Never adjust the steering wheel when the vehicle is moving.
The steering column can be adjusted manually by moving the four-way rocker adjustment control located on the multi-function control below the turn signal/wiper control stalk. The control will adjust the column as long as held or until the column reaches the end of travel.
The telescope function is adjusted by moving the control toward the driver to telescope out and moving the control toward the instrument panel to telescope in.
The tilt function is adjusted by moving the control up to tilt up and moving the control down to tilt down.
55
Page 56
Driver Controls
During easy exit operation, the column will move to the full in and up position. When the key is inserted into the ignition switch, the column will return to the previous setting. When you remove the key, the column will move away.
AUXILIARY POWER POINT
The power point is an additional power source for electrical accessories.
A power point is located on the instrument panel.
Do not use the auxiliary power point as a cigarette lighter.
The use of non-Ford approved electrical accessories could cause damage not covered by your warranty.
Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.
POWER WINDOWS
Press and hold the rocker switches to open and close windows.
Press the top portion of the rocker switch to close.
ON
OFF
PASSENGER AIRBAG
56
AUTO
Page 57
Driver Controls
Press the bottom portion of the rocker switch to open.
AUTO
One touch down
Press AUTO completely down to the second detent. The drivers window will open fully. Depress up to stop window operation.
AUTO
Accessory delay
With accessory delay, the window switches, radio, and the convertible top motor, may be used for up to ten minutes after the ignition switch is turned to the OFF position or until either front door is opened.
Short drop glass
In order to improve door efforts and sealing, your vehicle is equipped with short drop glass. This feature lowers the glass when either door is opened. The glass returns to its closed position when the door is closed. If the optional removable top is not installed on your vehicle, this feature will also lower the glass when the convertible top switch is operated. The glass will return to its closed position if the transmission is shifted out of P (Park), or if the opposite door becomes closed.
57
Page 58
Driver Controls
Proper operation of the short drop glass requires that the windows be calibrated. Though your windows will have been calibrated before
your vehicle is delivered to you, it is possible for the windows to lose calibration. If a window loses its calibration, your short drop
feature will lower the window, but will not raise it again when the door is closed. To re-calibrate the window, press the up switch to raise the window until it completes its travel and hold the switch down for 2 seconds. Another possible effect of lost calibration is that the feature may not lower the window. To re-calibrate the window in this case, lower the window until it completes its travel and hold the switch down for 2 seconds. Immediately after releasing the window down switch, press the up switch to raise the window until it completes its travel and hold the switch down for 2 seconds.
POWER SIDE VIEW MIRRORS
The power mirrors can be operated at any time.
To adjust your mirrors:
1. Select L to adjust the left mirror
or R to adjust the right mirror.
LR
2. Move the control in the direction
you wish to tilt the mirror.
LR
3. Return to the center position to lock mirrors in place.
58
Page 59
Driver Controls
LOCKABLE AND ELECTRONIC TRUNK REMOTE CONTROL
The remote trunk release control is located on the drivers door trim panel and can be operated at any time, except when the security system is armed. This control will not work until the vehicle is disarmed.
You can render the switch inoperable by locking the button with your master key.
In the event of battery failure, you can open the trunk by using your master key on the key cylinder
located behind the driver’s seat.
SPEED CONTROL
To turn speed control on
Press ON.
Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph).
Do not shift the gearshift lever into N (Neutral) with the speed control on.
Do not use the speed
control in heavy traffic or on roads that are winding, slippery, or unpaved.
59
Page 60
Driver Controls
To turn speed control off
Press OFF or
Turn off the vehicle ignition.
Once speed control is switched off, the previously programmed set speed will be erased.
To set a speed
Press SET+ / SET−. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal.
Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed.
If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing RES will re-engage it.
60
Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
Page 61
Driver Controls
To set a higher set speed
Press and hold SET+. Release the control when the desired vehicle speed is reached or
Press and release SET + to operate the Tap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or
Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET +.
You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed.
To set a lower set speed
Press and hold SET . Release the control when the desired speed is reached or
Press and release SET to operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or
Press CANCEL or depress the brake pedal. When the desired vehicle speed is reached, press SET + / SET .
61
Page 62
Driver Controls
To disengage speed control
Press CANCEL, or
depress the brake pedal.
Disengaging the speed control will not erase the previously programmed set speed.
Pressing OFF will erase the previously programmed set speed.
62
Page 63
Driver Controls
To return to a previously set speed
Press RESUME. For RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Indicator light
This light comes on when the vehicle speed control is engaged and actively controlling vehicle speed.
STEERING WHEEL CONTROLS
These controls allow you to operate some audio control features.
Audio control features
Press MEDIA to select AM, FM1, FM2, TAPE, or CD (if equipped).
MUTE
MEDIA
VOL
63
Page 64
Driver Controls
In AM, FM1, or FM2 mode:
Press or to select preset stations within the selected radio band.
In Tape mode:
Press or to select the next selection on the tape.
In CD mode:
Press or to select the next selection on the CD.
In any mode:
Press VOL + or to adjust volume.
Press the PHONE/MUTE control to mute the playing media. Press again to return to the playing media.
If your vehicle is equipped with a factory installed cellular phone, refer to the Phone/Mute Mode section of the Audio chapter.
MUTE
VOL
MEDIA
MUTE
VOL
MEDIA
MUTE
VOL
MEDIA
CONVERTIBLE
Articles stored in the convertible top stowage compartment may break the rear glass window when the top is lowered.
Lowering the convertible top
The convertible top can be lowered with the side windows either up or down.
64
Page 65
Driver Controls
Do not lower the top when the top material is wet.
If you raise and lower the convertible top several times in a row, the motor will heat up, causing the thermal circuit breaker to open so that the top will stop operating. The convertible top will operate again after allowing the motor to cool several minutes.
To lower the convertible top:
1. Bring vehicle to a complete stop. Put the gearshift in the P (Park)
position. The convertible top will operate with the key in the RUN position,
RUN/ACC position or in the accessory delay mode. It is recommended that the vehicles engine is running when lowering the top to prevent draining the battery.
2. Check the convertible top stowage compartment behind the seat to be
sure it is empty and ready to receive the top.
3. Press the button on the
convertible top handle and pull the handle down and forward to release the clamps from the windshield header.
4. Push the convertible top
switch on the instrument panel and hold until the top is completely stored in the stowage compartment.
5. Push the handle back into the lock position.
Installation of the tonneau cover
Be sure the cover is tucked into the deck lid and all snaps are fastened before driving.
65
Page 66
Driver Controls
1. Push boot rearward and engage
boot under the upper back panel at the rear and the quarter panel along the sides.
2. Fasten the snaps on boot to the
quarter trim panel on both sides of the vehicle and at the center.
3. To remove unfasten the snaps.
4. Pull forward and lift off.
Raising the convertible top
To raise the convertible top:
1. Bring the vehicle to a complete stop. Put the vehicle in the P (Park)
position.
The convertible top will operate with the key in the RUN position, RUN/ACC position or in the accessory delay mode. It is recommended that the vehicles engine is running when raising the top to prevent draining the battery.
66
Page 67
Driver Controls
2. Remove the tonneau cover and store it in the luggage compartment.
3. Push the two screws down into
the windscreen panel of your vehicle.
4. Push the convertible top
switch, holding it until the top unfolds and moves forward toward the windshield header.
5. Press the button on the
convertible top handle and pull the handle down to open both top clamps before the top meets the windshield header.
6. Resume pushing the convertible top switch until it has reached the
fully closed position flush to the header.
7. The two pins under the forward edge of the top should seat
themselves in the matching holes in the header.
67
Page 68
Driver Controls
8. To fasten both clamps securely,
push the clamp handles into the header on the top until they are flush with the header. Pulling down on the header at the center grip while closing the latches may assist in fastening the clamps. Use the pull cups located on either side of the convertible top handle.
9. Push the convertible top handle
back up so that it locks into position.
Prolonged storage
It may be difficult to pull down and latch the convertible top after prolonged storage with the top in the down position over the winter or in colder temperatures. This difficulty will decline over time with warmer temperatures and the convertible top in the full up or latched position.
Convertible top and padded molding care
To avoid damage to the cloth top and moldings, use only an approved Ford cleaner, or equivalent. Do not use abrasive material or cleaners.
Hot waxes applied by automatic car washes can affect the cleanability of cloth material.
Using high water pressure or wand type car washes against the convertible top and windows may cause water leaks and possible seal damage.
68
Page 69
Driver Controls
REMOVABLE TOP (IF EQUIPPED)
For more information see the CD Rom included with this guide.
Installing the removable top
The front screw fittings must be checked to see that they are firmly seated after driving a distance of approximately 50 to 60
km (30 to 40 miles).
The removable top does not have the same crush resistance as an integrated steel roof in case of collision or rollover.
The removable top is not, under any circumstances, to be used to carry or support external loads.
Movement of the removable top requires at least two people. The removable top weighs approximately 38 kg (84 lb). Also,
due to its shape, the weight is biased to the rear of the removable top.
Your vehicle must be turned OFF and placed in PARK on a level surface prior to installing or removing the top.
Before installing the removable top, unsnap and properly store the convertible top tonneau cover. Refer to Installation of the tonneau cover in the Convertible section. Also, thoroughly dry the convertible top and then lower. Open the doors, lower the windows, and clean the area where the removable top mounts on the body.
1. Remove the protective cover from the top. Using a mild detergent,
clean the weather-strips on the top before installing it on the vehicle.
2. Ensure that the removable top levers are rotated rearward to the fully
open position. Lock the wheels on the storage cart, loosen the restraining straps on the cart, and with the help of at least another person remove the top from the cart.
69
Page 70
Driver Controls
Once per year, apply a small amount of silicone lubricant, F5AZ–19553–AA, to the receivers as shown. The lubricant should be sprayed directly into the hole to avoid contaminating the trim parts.
3. Lower the rear of the top into
position so that the pins are placed into the bracket receivers.
4. Position the front of the top so that the locating tabs on each side are
placed in the mounting castings. Ensure that the weather-strip on the top is placed on the body mounted seal without any wrinkles or gaps. The joint should have a smooth and continuous transition to prevent water leaks.
5. Take the mounting key from the bag located in the trunk.
70
Page 71
6. Partially turn, 1/2 turn forward,
the levers of the top (located in the rear on the left and right-hand side of the vehicle).
7. Using the mounting key, loosely
screw in the two screws at the front of the top by two or three turns. The two screws are already located in the windscreen panel of your vehicle.
8. Turn and lock the levers fully
forward. The levers are locked when you feel the spring engage and the levers are pointing toward the front of the vehicle.
Driver Controls
9. Using the mounting key, finish tightening the screws at the front of
the removable top all the way so that they are secure.
The front screw fittings must be checked to see that they are firmly seated after a distance of approximately 50 to 60 km (30
to 40 miles).
71
Page 72
Driver Controls
Removing the top
It is recommended that you prepare the storage rack before removing the top. See Removable top storage rack in this section.
1. Take the mounting key from the bag located in the trunk.
2. Using the mounting key, loosen
the two screws at the front of the top. The two screws remain undetachable in the windscreen panel of your vehicle.
3. Push the two screws down into
the windscreen panel of your vehicle.
4. Undo the locking levers at the
rear right and left sides of the vehicle. Rotate the levers rearward while applying a slight upward force to the top.
5. With the aid of a second person,
lift the top off the vehicle and store it as described in Removable top storage in the chapter.
Removable top storage rack
It is recommended that you prepare the storage rack prior to removing the top from the vehicle.
72
Page 73
Driver Controls
1. Remove the storage rack from the package and place the bumper end
of the uprights on the floor with the wheels facing you.
2. Locate the two chrome locking
buttons on each of the two rack legs.
3. Firmly squeeze the two chrome
buttons (top and bottom) on one leg and rotate the leg toward you until the leg snaps into place.
4. Squeeze the second set of chrome
buttons (top and bottom) for the opposite leg until the leg snaps into place.
5. Turn the rack over on its wheels
and place the removable top storage rack on a flat level surface. Make sure the center Tsection is fully locked by attempting to move the section downward without depressing the chrome locking buttons.
6. Lock the two front wheels located
on the ends of each of the two rack legs.
7. To lock the wheels, push down on
the bottom part of the plastic tab located on the tip of each wheel.
73
Page 74
Driver Controls
8. Place the removable top on the
storage rack. Make sure the rear edge of the removable top rests on the rubber bumpers of the rack legs. This prevents damage to the painted edge and the weather-strips.
9. Buckle and tighten the retaining
strap and unlock the cart wheels before moving the top and cart.
To unlock the wheels, pull up on the lower portion of the plastic tab located on the tip of each wheel.
Place the mounting key in a safe place to use again.
Keep your removable top clean by placing the provided cover over it.
If you plan to drive with the convertible top down, ensure all the snaps on the convertible top tonneau cover are fastened and that the rear of the cover is firmly tucked before driving. Refer to Installation of the tonneau cover in the Convertible section.
74
Page 75
Driver Controls
CENTER CONSOLE
Your vehicle may be equipped with a variety of console features. These include:
Utility compartment
Cellular phone (if equipped)
Cupholders
Ash tray
POSITIVE RETENTION FLOOR MAT
Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.
75
Page 76
Locks and Security
KEYS
The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer.
You should always carry a second key with you in a safe place in case you require it in an emergency.
Refer to SecuriLockPassive Anti-Theft System for more information.
POWER DOOR LOCKS
Press the top of the control to unlock all doors and the bottom to lock all doors.
When the vehicles security system is armed, the power door locks and remote trunk release control are disabled; these features will not work until the security system is disarmed.
Smart locks
With the key in the ignition, and the drivers door open, the doors cannot be locked using the drivers power door lock switches. If this is attempted, both doors will lock, then the drivers door will immediately unlock.
The vehicle can still be locked. with the key in the ignition, using the manual lock button on the door, operating the remote entry transmitter, or locking the drivers door with the a key.
INTERIOR LUGGAGE COMPARTMENT RELEASE
Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment.
Adults are advised to familiarize themselves with the operation and location of the release handle.
76
Page 77
To open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated Tshaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light.
The Tshaped handle will be located either on the luggage compartment door (lid) or inside the luggage compartment near the tail lamps.
Keep vehicle doors and
luggage compartment locked and keep keys and remote transmitters out of a childs reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles.
Locks and Security
On hot days, the temperature in the trunk or vehicle interior can
rise very quickly. Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.
REMOTE ENTRY SYSTEM
This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
77
Page 78
Locks and Security
Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
Your remote entry system contains two remote transmitters which provide remote control of several features. Each remote transmitter will allow you to:
unlock the vehicle doors without a key
lock all the vehicle doors without a key
open the trunk without a key
activate the personal alarm
arm and disarm the perimeter anti-theft system
operate the illuminated entry feature
The remote transmitter features only operate with the ignition in the OFF or ACC positions. The remote transmitter features also operate if the ignition is in the RUN position and the gear shift is in P (Park). The personal alarm feature, however, will not operate when the ignition is in the RUN position.
When the vehicle is armed the power door locks and remote trunk release control are disabled. These will not work until the vehicle is disarmed.
If there is any potential remote keyless entry problem with your vehicle, ensure ALL remote entry transmitters are brought to the dealership, to aid in troubleshooting.
Locking the doors
Press this control to lock all the doors and arm the perimeter anti-theft system. To confirm all the doors and trunk are closed, the turn signal lamps will display one short flash. Press the control twice within 3 seconds the horn will chirp once, confirming that all doors, hood or trunk are closed. If any of the doors, hood or trunk are open or ajar, the horn will make two quick chirps, reminding you to properly close them.
78
Page 79
Unlocking the doors
Press this control to unlock the driver door and disarm the perimeter alarm (if armed). The interior lamps will illuminate.
Press the control a second time within three seconds to unlock all the doors.
Opening the trunk
Press this control to open the trunk.
Be certain the trunk is closed before driving your vehicle. The trunk may appear closed, but it may not be latched. Failure to do so may cause objects to fall out of the trunk or block rear view vision.
Locks and Security
Activating the personal alarm
Press this control to turn on the personal alarm.
Press the control a second time to turn off the personal alarm. The personal alarm will also turn off if the remote transmitter unlock control is pressed, or if the ignition is turned out of the OFF position, or after 2–3 minutes of operation.
79
Page 80
Locks and Security
Replacing the battery
The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by the following factors:
Weather conditions
Nearby radio towers
Structures around the vehicle
Other vehicles parked next to the vehicle
To replace the battery:
1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART.
2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit.
3. Snap the two halves back together.
Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.
Replacing lost transmitters
If a remote transmitter has been lost and you would like to remove it from the vehicles memory, or you would like to purchase additional transmitters for your vehicle (up to four may be programmed into memory):
Take all your vehicles
transmitters to your dealer for programming, or
Perform the reprogramming procedure yourself.
80
Page 81
Locks and Security
Reprogramming transmitters
It will be necessary to reprogram all the transmitters to the vehicle at the same time while performing this procedure.
To program the transmitter yourself:
1. To reprogram the transmitters yourself, place the key in the ignition and turn from (2) OFF to (4) RUN and cycle between (4) RUN and (2) OFF eight times in rapid succession (within 10 seconds) ending in the (4) RUN position.
2. After doors lock/unlock, press any control on all transmitters (up to four). With each control press of the transmitters, the door should cycle (lock/unlock) to confirm programming. When completed, turn the ignition to (2) OFF.
3. The door locks should cycle (lock/unlock) one last time to confirm completion of programming.
Illuminated entry
The illuminated entry feature will automatically turn on the interior lamps when the remote transmitter unlock control is pressed.
The illuminated entry feature will automatically turn off the interior lamps if the ignition is turned out of the OFF position, or if the remote transmitter lock control is pressed, or after 25 seconds of illumination.
The interior lamps will not turn off if:
they have been turned on with the instrument panel dimmer control, or
any door is open.
The battery saver will turn off the interior lamps 30 minutes after the last door is closed even if the dimmer control is on.
2
1
3
4
5
Autolock/Relock
This feature automatically locks all vehicle doors when:
all doors are closed,
the engine is running and
you shift out of P (Park).
81
Page 82
Locks and Security
Relock
The autolock feature repeats when:
the passengers door is opened then closed while the engine is running, and
you put the vehicle in motion.
Deactivating/activating the autolock/relock feature
Before following the procedure, make sure that the ignition is OFF and all vehicle doors are closed.
You must complete steps 1-5 within 30 seconds or the procedure will have to be repeated. Wait 30 seconds before repeating the procedure.
1. Turn the ignition key to RUN.
2. Press the power door unlock control three times.
3. Turn the ignition key from RUN to OFF.
4. Press the power door unlock control three times.
5. Turn the ignition back to RUN. The horn will chirp to indicate that
you have entered the programming mode.
6. Press the unlock control, then press the lock control. The horn will
chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated.
7. Turn the ignition to OFF. The horn will chirp once to confirm the
procedure is complete.
SECURILOCKPASSIVE ANTI-THEFT SYSTEM
SecuriLockpassive anti-theft system is an engine immobilization system. This system is designed to prevent the engine from being started unless a coded key programmed to your vehicle is used.
The SecuriLockpassive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
THEFT INDICATOR
The theft indicator is the flashing red indicator located on the dash panel.
When the ignition is in the OFF position, the indicator will flash once every 2 seconds to indicate the SecuriLocksystem is functioning as a theft deterrent.
82
Page 83
Locks and Security
When the ignition is in the ON position, the indicator will glow for 3 seconds to indicate normal system functionality.
If a problem occurs with the SecuriLocksystem, the indicator will flash rapidly or glow steadily when the ignition is in the ON position. If this occurs, the vehicle should be taken to an authorized dealer for service.
Automatic arming
The vehicle is armed immediately after switching the ignition to the 2 (OFF) position.
Automatic disarming
Switching the ignition to the 4 (RUN) position with a coded key disarms the vehicle. The
then go out. If the
THEFT
indicator will illuminate for three seconds and
THEFT
indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your dealership or a qualified technician.
Key information
Your vehicle is supplied with two coded keys. Only a coded key will start your vehicle.
Spare coded keys can be purchased from your dealership. Your dealership can program your key or you can do it yourself.Refer to
Programming spare keys.
The following items may prevent the vehicle from starting:
Large metallic objects
Electronic devices on the key chain that can be used to purchase
gasoline or similar items
A second key on the same key ring as the coded key
If any of these items are present, you need to keep these objects from touching the coded key while starting the engine. These objects and devices cannot damage the coded key, but can cause a momentary no startcondition if they are too close to the key during engine start. If a
2
1
3
4
5
83
Page 84
Locks and Security
problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Ford coded key.
If your keys are lost or stolen you will need to do the following:
Use your spare key to start the vehicle. or
Have your vehicle towed to a dealership or a locksmith. The key codes
will need to be erased from your vehicle and new key codes will need to be re-coded.
Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience.
The correct coded key must be used for your vehicle. The use of the wrong type of coded key may lead to a no startcondition.
If an unprogrammed key is used in the ignition it will cause a no startcondition.
Programming spare keys
A maximum of eight keys can be coded to your vehicle. Only SecuriLockkeys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicles engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure.
If two previously programmed coded keys are not available, you must bring your vehicle to your dealership to have the spare coded key(s) programmed.
Please read and understand the entire procedure before you begin.
1. Insert the first previously programmed coded key into the ignition and turn the ignition from 1 (LOCK) to 4 (RUN) (maintain ignition in 4 (RUN) for at least one second).
2. Turn ignition to 1 (LOCK) and remove the first coded key from the ignition.
2
1
3
4
5
84
Page 85
Locks and Security
3. Within ten seconds of turning the ignition to 1 (LOCK), insert the second previously programmed coded key into the ignition and turn the ignition from 1 (LOCK) to 4 (RUN) (maintain ignition in 4 (RUN) for at least one second but no more than ten seconds).
4. Turn the ignition to 1 (LOCK) and remove the second coded key from the ignition.
5. Within 20 seconds of turning the ignition to 1 (LOCK), insert the new unprogrammed key (new key) into the ignition and turn the ignition from 1 (LOCK) to 4 (RUN) (maintain ignition in 4 (RUN) for at least one second). This step will program your new key to a coded key.
6. To program additional new unprogrammed key(s), repeat this procedure from step 1.
If successful, the new coded key(s) will start the vehicles engine and the theft indicator will illuminate for three seconds and then go out.
If not successful, the new coded key(s) will not start the vehicle’s engine, the theft indicator will flash on and off and you may repeat steps 1 through 6. If failure repeats, bring your vehicle to your dealership to have the new spare key(s) programmed.
PERIMETER ALARM SYSTEM
The perimeter anti-theft system will help protect your vehicle doors, hood and trunk from unauthorized entry.
When the vehicle is armed the power door locks and remote trunk release control are disabled. These will not work until the vehicle is disarmed. Refer to Driver Controls chapter for more information.
If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are brought to the dealership, to aid in troubleshooting.
Theft indicator
When the perimeter alarm is armed, the theft indicator on the instrument panel will flash briefly every two seconds to indicate the perimeter alarm system is protecting your vehicle.
85
Page 86
Locks and Security
Arming the system
When armed, the perimeter alarm will help protect your vehicle from unauthorized entry. When unauthorized entry occurs, the system will flash the turn signal lamps and the theft indicator lamp and will sound the horn.
The system is ready to arm whenever the key is out of the ignition. The system will arm 20 seconds after one of the following actions:
Press the remote transmitter lock control.
Open a door and press the power door lock control.
Disarming the system
You can disarm the system by any of the following actions:
Unlock the doors by using your remote entry transmitter.
Unlock the drivers door by using your key.
Turn ignition to RUN.
86
Page 87
Seating and Safety Restraints
SEATING
Adjustable head restraints (if equipped)
Your vehicles seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
The head restraints can be moved up and down.
Push control to lower head restraint.
87
Page 88
Seating and Safety Restraints
Using the manual lumbar support
The lumbar control is located on the front of the drivers seat cushion.
Turn to adjust lumbar support.
Using the manual recline function (if equipped)
Never adjust the drivers seat or seatback when the vehicle is moving.
The driver and passenger seat must be in the upright position and the lap belt must be snug and low across the hips while the
vehicle is moving.
To adjust the front seatback using the manual recliner:
Lift and hold the handle located
on the side of the seat.
Lean against the seatback to
adjust it to your desired position. You can recline the seat back or bring it forward.
Release the handle when the
desired position has been reached.
Adjusting the driver’s power seat
Never adjust the drivers seat or seatback when the vehicle is moving.
Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
88
Page 89
Seating and Safety Restraints
The driver and passenger seat must be in the upright position and the lap belt must be snug and low across the hips while the
vehicle is moving.
Reclining the seatback can cause an occupant to slide under the seats safety belt, resulting in severe personal injuries in the
event of a collision.
The seat position control is located on the outboard side of the seat cushion.
Press front to raise or lower the front portion of the seat cushion.
Press rear to raise or lower the rear portion of the seat cushion.
Press the control to move the seat forward, backward, up or down.
Adjusting the passengers power seat
Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
89
Page 90
Seating and Safety Restraints
The driver and passenger seat must be in the upright position and the lap belt must be snug and low across the hips while the
vehicle is moving.
Reclining the seatback can cause an occupant to slide under the seats safety belt, resulting in severe personal injuries in the
event of a collision.
The control is located on the outboard side of the seat cushion.
Press the control to move the seat forward or backward.
SAFETY RESTRAINTS Safety restraints precautions
The driver and passenger seat must be in the upright position and the lap belt must be snug and low across the hips while the
vehicle is moving.
To reduce the risk of injury, make sure children sit where they can be properly restrained.
Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from
injury in a collision.
All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is
provided.
90
Page 91
Seating and Safety Restraints
It is extremely dangerous to ride in a cargo area, inside or
outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.
In a rollover crash, an unbelted person is significantly more likely
to die than a person wearing a safety belt.
Each seating position in your vehicle has a specific safety belt
assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm.
2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.
Combination lap and shoulder belts
Before fastening the safety belt, make sure the shoulder belt passes through the belt holder on the top of the seatback.
91
Page 92
Seating and Safety Restraints
1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
2. To unfasten, push the release button and remove the tongue from the buckle.
Energy Management Feature
The safety belts in the vehicle are combination lap and shoulder belts.
This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision.
This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupants chest.
After any vehicle collision, the seat belt system at all passenger
seating positions must be checked by a qualified technician to verify that the automatic locking retractorfeature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.
92
Page 93
Seating and Safety Restraints
BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if
the seat belt assembly automatic locking retractorfeature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual.
Failure to replace the Belt and Retractor assembly could
increase the risk of injury in collisions.
Vehicle sensitive mode
The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.
Automatic locking mode
How to use the automatic locking mode
Buckle the combination lap and shoulder belt.
93
Page 94
Seating and Safety Restraints
Grasp the shoulder portion and pull downward until the entire belt is extracted.
Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt.
The automatic locking mode is not available on the driver safety belt.
When to use the automatic locking mode
Anytime a child safety seat is installed in the vehicle. Refer to Safety Restraints for Children or Safety Seats for Children later in this
chapter.
How to disengage the automatic locking mode
Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
After any vehicle collision, the combination lap and shoulder belt
system at all passenger seating positions must be checked by a qualified technician to verify that the automatic locking retractor feature for child seats is still functioning properly, in addition to other checks for proper seat belt system function.
94
Page 95
Seating and Safety Restraints
BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if
the seat belt assembly automatic locking retractorfeature or any other seat belt function is not operating properly. In addition, all seat belts should be checked for proper function.
Failure to replace the belt and retractor assembly could increase
the risk of injury in collisions.
Safety belt pretensioner
Your vehicle is equipped with safety belt pretensioners at the driver and front passenger seating positions.
The safety belt pretensioner is a device which removes excess webbing from the safety belt system. The safety belt pretensioner uses the same crash sensor system as the front air bag supplemental restraint system (SRS). When the safety belt pretensioner deploys, webbing from the lap and shoulder belt is tightened. The driver and front passenger seat belt system (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results in deployment of front air bags and safety belt pretensioners. Refer to the Safety belt maintenance section in this chapter.
Failure to replace the safety belt assembly under the above
conditions could result in severe personal injuries in the event of a collision.
Safety belt warning light and indicator chime
The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.
95
Page 96
Seating and Safety Restraints
Conditions of operation
If... Then...
The driver’s safety belt is not buckled before the ignition switch is turned to the RUN position...
The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
The driver’s safety belt is buckled before the ignition switch is turned to the RUN position...
BeltMinder
The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the drivers safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster.
If... Then...
The driver’s safety belt is not buckled before the vehicle has reached at least 5 km/h (3 mph) and 1-2 minutes have elapsed since the ignition switch has been turned to ON...
The driver’s safety belt is buckled while the safety belt indicator light is illuminated and the safety belt warning chime is sounding...
The driver’s safety belt is buckled before the ignition switch is turned to the ON position...
The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
The safety belt warning light and warning chime turn off.
The safety belt warning light and indicator chime remain off.
The BeltMinder feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until safety belt is buckled.
The BeltMinder feature will not activate.
The BeltMinder feature will not activate.
96
Page 97
Seating and Safety Restraints
The purpose of the BeltMinder is to remind occasional wearers to wear safety belts all of the time.
The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data)
Reasons given... Consider...
Crashes are rare events
Im not going far3of4fatal crashes occur within 25 miles of home.Belts are
uncomfortable
I was in a hurry Prime time for an accident. BeltMinder reminds
Safety belts dont work
Traffic is light Nearly 1 of 2 deaths occur in single-vehicle
Belts wrinkle my clothes
The people Im
with dont wear belts
I have an air bagAir bags offer greater protection when used with
36700 crashes occur every day. The more we drive, the more we are exposed to rareevents, even for good drivers. 1 in 4 of us will be
seriously injured in a crash during our lifetime.
We design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort.
us to take a few seconds to buckle up.
Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks.
crashes, many when no other vehicles are around.
Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted.
Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see.
safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers.
97
Page 98
Seating and Safety Restraints
Reasons given... Consider...
Id rather be thrown clear
Do not sit on top of a buckled safety belt to avoid the Belt
Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.
One time disable
Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, BeltMinder will be disabled for that ignition cycle only.
Deactivating/activating the BeltMinder feature
Read steps1-9thoroughly before proceeding with the deactivation/activation programming procedure.
The BeltMinder feature can be deactivated/activated by performing the following procedure:
Before following the procedure, make sure that:
The parking brake is set.
The gearshift is in P (Park) (automatic transmission) or the neutral
position (manual transmission).
The ignition switch is in the OFF position.
All vehicle doors are closed.
The drivers safety belt is unbuckled.
The parklamps are in OFF position.
Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help
prevent ejection, WE CANT PICK OUR CRASH.
To reduce the risk of injury, do not deactivate/activate the Belt
Minder feature while driving the vehicle.
1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.)
2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes.)
Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated.
98
Page 99
Seating and Safety Restraints
3. Buckle then unbuckle the safety belt three times, ending with the
safety belt unbuckled. This can be done before or during BeltMinder warning activation.
4. Turn on the parklamps, turn off the parklamps.
5. Buckle then unbuckle the safety belt three times, ending with the
safety belt unbuckled.
After step 5 the safety belt warning light will be turned on for three seconds.
6. Within seven seconds of the safety belt warning light turning off,
buckle then unbuckle the safety belt.
This will disable BeltMinder if it is currently enabled, or enable BeltMinder if it is currently disabled.
7. Confirmation of disabling BeltMinder is provided by the safety belt
warning light flashing four times per second for three seconds.
8. Confirmation of enabling BeltMinder is provided by:
The safety belt warning light flashing four times per second for three seconds.
Followed by three seconds with the safety belt warning light off.
Once again, the safety belt warning light will flash four times per
second for three seconds.
9. After receiving confirmation, the deactivation/activation procedure is
complete.
Safety belt extension assembly
If the safety belt is too short when fully extended, there is a 20 cm (8 inch) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost.
Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended.
Do not use extensions to change the fit of the shoulder belt across the torso.
Safety belt maintenance
Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure
99
Page 100
Seating and Safety Restraints
there are no nicks, tears or cuts. Replace if necessary. All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if equipped), child safety seat tether bracket assemblies (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.
Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe
personal injuries in the event of a collision.
Refer to Interior in the Cleaning chapter.
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity. This information will assist Ford Motor Company in servicing the vehicle and in helping to better understand real world collisions and further improve the safety of future vehicles.
100
Loading...