Ford Excursion 2004 User Manual

Page 1
Table of Contents
Introduction 4
Instrument Cluster 10
Warning and control lights 10 Gauges 13
Entertainment Systems 17
AM/FM stereo cassette with CD 17 AM/FM stereo with CD 21 Rear seat controls 24 Rear seat entertainment system 26
Heater only 42 Manual heating and air conditioning 43 Electronic automatic temperature control 44 Rear window defroster 47
Lights 48
Headlamps 48 Turn signal control 50 Bulb replacement 52
Windshield wiper/washer control 57 Steering wheel adjustment 58 Power windows 63 Mirrors 63 Speed control 67 Message center 70
1
Page 2
Table of Contents
Locks and Security 81
Keys 81 Locks 81 Anti-theft system 83
Seating and Safety Restraints 93
Seating 93 Safety restraints 104 Air bags 115 Child restraints 119
Driving 130
Starting 130 Brakes 134 Transmission operation 137 Vehicle loading 158 Trailer towing 162 Recreational towing 166
Getting roadside assistance 167 Hazard flasher switch 168 Fuel pump shut-off switch 168 Fuses and relays 169 Changing tires 174 Jump starting 180 Wrecker towing 185
Reporting safety defects (U.S. only) 194
2
Page 3
Table of Contents
Cleaning 195
Maintenance and Specifications 201
Engine compartment 202 Engine oil 204 Battery 207 Fuel information 215 Air filter(s) 230 Tire Information 232 Part numbers 244 Refill capacities 245 Lubricant specifications 248
Accessories 256
Index 259
All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.
Copyright © 2003 Ford Motor Company
3
Page 4

Introduction

Introduction
CALIFORNIA Proposition 65 Warning
WARNING: Engine exhaust, some of its constituents, and
certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
CONGRATULATIONS
Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.
For more information on Ford Motor Company and its products visit the following website:
In the United States: www.ford.com
In Canada: www.ford.ca
In Australia: www.ford.com.au
In Mexico: www.ford.com.mx
Additional owner information is given in separate publications.
This Owner’s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available.
Remember to pass on this Owner’s Guide when reselling the vehicle. It is an integral part of the vehicle.
Fuel pump shut-off switch: In the event of an accident the
safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emergencies chapter.
4
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 5
Introduction
SAFETY AND ENVIRONMENT PROTECTION
Warning symbols in this guide
How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
Warning symbols on your vehicle
When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Protecting the environment
We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.
BREAKING-IN YOUR VEHICLE
There are no particular guidelines for breaking-in your vehicle. During the first 1,600 km (1,000 miles) of driving, vary speeds frequently. This is recommended to give the moving parts a chance to break in.
SPECIAL NOTICES
Emission warranty
The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
5
Page 6
Introduction
Service Data Recording
Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may access vehicle diagnostic information through a direct connection to your vehicle when diagnosing or servicing your vehicle.
Event Data Recording
Other modules in your vehicle event data recorders are capable of collecting and storing data during a crash or near crash event. The recorded information may assist in the investigation of such an event. The modules may record information about both the vehicle and the occupants, potentially including information such as:
how various systems in your vehicle were operating;
whether or not the driver and passenger seatbelts were buckled;
how far (if at all) the driver was depressing the accelerator and/or the
brake pedal;
how fast the vehicle was traveling; and
where the driver was positioning the steering wheel.
To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.
Special instructions
For your added safety, your vehicle is fitted with sophisticated electronic controls.
Please read the section Supplemental restraint system (SRS)
in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury.
6
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 7
Introduction
Front seat mounted rear-facing child or infant seats should
NEVER be placed in front of an active passenger air bag.
Notice to owners of diesel-powered vehicles
Read the 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owners Guide Supplement for information regarding correct operation and
maintenance of your Diesel-powered light truck.
Notice to owners of pickup trucks and utility type vehicles
Utility vehicles have a significantly higher rollover rate than
other types of vehicles.
Before you drive your vehicle, please read this Owners Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of vehicle control, vehicle rollover, personal injury or death.
Be sure to read Driving off road in the Driving chapter.
Snowplowing
The Excursion is not recommended for snowplow installation. Ford makes no representation as to the suitability of the Excursion for snowplowing, in particular regarding the potential for exceeding vehicle weight limits, airbag (SRS) deployment sensitivity, vehicle crash integrity, or powertrain durability. The Snowplow Package Option is not available.
Middle East/North Africa vehicle specific information
For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owners Guide; therefore, a supplement has been supplied that complements this book. By referring to the pages in the provided supplement, you can properly identify those features, recommendations and specifications that are unique to your vehicle. Refer to this
Owner’s Guide for all other required information and warnings.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
7
Page 8
Introduction
These are some of the symbols you may see on your vehicle.
Vehicle Symbol Glossary
Safety Alert
Fasten Safety Belt Air Bag-Front
Air Bag-Side Child Seat
Child Seat Installation Warning
Child Seat Tether Anchor
Anti-Lock Brake System
Traction Control AdvanceTrac
Master Lighting Switch Hazard Warning Flasher
Fog Lamps-Front Fuse Compartment
See Owner’s Guide
Child Seat Lower Anchor
Brake System
Brake Fluid ­Non-Petroleum Based
Fuel Pump Reset Windshield Wash/Wipe
Windshield Defrost/Demist
8
Rear Window Defrost/Demist
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 9
Vehicle Symbol Glossary
Introduction
Power Windows Front/Rear
Child Safety Door Lock/Unlock
Power Window Lockout
Interior Luggage Compartment Release Symbol
Panic Alarm Engine Oil
Engine Coolant
Engine Coolant Temperature
Do Not Open When Hot Battery
Avoid Smoking, Flames, or Sparks
Battery Acid
Explosive Gas Fan Warning
Power Steering Fluid
Maintain Correct Fluid Level
Emission System Engine Air Filter
MAX
MIN
Passenger Compartment Air Filter
Jack
Check fuel cap Low tire warning
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
9
Page 10

Instrument Cluster

Instrument Cluster
WARNING LIGHTS AND CHIMES
THEFT
TRANS
TEMP
BRAKE
4x4
LOW
RANGE
H
L
F
E
20
MPH
80
00
60
40
0
km/h
20
40
60
PRND2
RPMX1000
SELECT
RESET
D
Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicles functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.
Service engine soon: The Service engine soon indicator light
illuminates when the ignition is first turned to the ON position to check the bulb. Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.
H
CHECK
GAGE
C
H
CK
SUSP
C
Under engine misfire conditions, excessive exhaust temperatures
could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
Check fuel cap (if equipped):
Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Service engine soon warning light to come on. Refer to Fuel filler cap in the Maintenance and Specifications chapter.
10
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 11
Instrument Cluster
Check gage: Illuminates when any of the following conditions has occurred:
The engine coolant temperature is high.
The engine oil pressure is low.
The fuel gauge is at or near empty.
Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and START, or by applying the parking brake when the ignition is turned to the ON position. If the brake system warning light does not illuminate at this time, seek service immediately from your dealership. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately by your servicing dealership.
Driving a vehicle with the brake system warning light on is
dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehicle checked by your dealer immediately.
Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately. Normal braking is still functional unless the brake warning light also is illuminated.
Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately. A chime will also sound when a malfunction in the supplemental restraint system has been detected.
CHECK
GAGE
ABS
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
11
Page 12
Instrument Cluster
Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt.
Charging system: Illuminates when the battery is not charging properly.
Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter).
Speed control: Illuminates when the speed control is activated. Turns off when the speed control system is deactivated.
Transmission Tow/Haul Feature (4R100 5–speed automatic transmission) (if equipped-Diesel engines only):
Illuminates when the Tow/Haul feature has been activated. Refer to the Driving chapter for transmission function and operation. If the light flashes steadily, have the system serviced immediately, damage to the transmission could occur.
Four wheel drive low (if equipped): Illuminates when
four-wheel drive low is engaged.
LOW
RANGE
Four wheel drive indicator (if equipped): Illuminates when
four-wheel drive is engaged.
SecurilockAnti-theft system:
Flashes when the Securilock Passive Anti-theft System has been activated.
12
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
4x4
Page 13
Instrument Cluster
Door ajar: Illuminates when the ignition is in the ON position and any door is open.
Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check for a burned out bulb.
High beams: Illuminates when the high beam headlamps are turned on.
Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the drivers door is opened.
Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the drivers door is opened.
Parking brake ON warning chime: Sounds when the parking brake is set, the engine is running and the vehicle is driven more than 5 Km (3 mph).
GAUGES
4x4
LOW
RANGE
H
L
F
E
20
MPH
80
00
60
40
0
km/h
20
40
60
PRND2
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
THEFT
TRANS
TEMP
BRAKE
H
CHECK
GAGE
C
H
CK
SUSP
C
RPMX1000
SELECT
RESET
D
13
Page 14
Instrument Cluster
Speedometer: Indicates the current vehicle speed.
Engine coolant temperature gauge: Indicates engine coolant
temperature. At normal operating temperature, the needle will be in the normal range (between Hand
C). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.
Never remove the coolant reservoir cap while the engine is
running or hot.
Odometer: Registers the total kilometers (miles) of the vehicle.
Trip odometer: Registers the kilometers (miles) of individual journeys. Press the control once to switch from the odometer to the trip odometer. To reset the trip, press the control again until the trip reading is 0.0 miles.
Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
14
PRND2
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
D
Page 15
Instrument Cluster
Engine oil pressure gauge:
Indicates engine oil pressure. The needle should stay in the normal operating range (between Land H). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level. Add oil if needed. If the oil level is correct, have your vehicle checked at your dealership or by a qualified technician.
Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade.
Refer to Filling the tank in the
Maintenance and Specifications
chapter for more information.
Transmission fluid temperature gauge: If the gauge is in the:
White area (normal) - the
transmission fluid is within the normal operating temperature (between Hand C).
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
15
Page 16
Instrument Cluster
Yellow area (warning) the transmission fluid is higher than normal operating temperature. This can be caused by special operation conditions (i.e. snowplowing, towing or off road use). Refer to Special
Operating Conditions in the Scheduled Maintenance Guide for
instructions. Operating the transmission for extended periods of time with the gauge in the yellow area may cause internal transmission damage.
Altering the severity of the driving conditions is recommended to lower the transmission temperature into the normal range.
Red area (over temperature) the transmission fluid is overheating. Stop the vehicle to allow the temperature to return to normal range.
If the gauge is operating in the Yellow or Red area, stop the vehicle and verify the airflow is not restricted such as snow or debris blocking airflow through the grill. If the gauge continues to show high temperatures, see your Ford dealer.
16
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 17

Entertainment Systems

Entertainment Systems
PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED)
1. Power/volume: Press to turn ON/OFF; turn to increase/decrease volume.
2. Scan: Press to hear a brief sampling of all listenable stations, tape selections or CD tracks. Press again to stop.
3. CD Door: Insert a CD with the label side up.
CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should
SCAN
17
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 18
Entertainment Systems
not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your dealer for further information.
4. Cassette door: Insert the cassette with the opening to the right.
5. Eject: Press to eject the cassette/CD. The radio will resume playing.
6. Tape: Press to start tape play. Press to stop tape during rewind/fast forward.
CD: Press to start CD play. With the dual media audio, press CD to toggle between single CD and CD changer play (if equipped).
7. Mute: Press to MUTE playing media; press again to return to the playing media.
8. Auto: Press to set first six strongest stations (if available) into AM, FM1 or FM2 memory buttons; press again to return to normal stations.
9. Clock: Press to toggle between station mode and clock mode. Press and hold to set the clock. Press the
SEEK to increase hours. Press
18
SEEK to decrease hours or
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 19
Entertainment Systems
the TUNE to decrease minutes or TUNE to increase minutes. If your vehicle has a stand alone clock this control will not function.
10. Balance: Press BAL; then press SEL left/right speakers.
Fade: Press FADE; then press SEL rear/front speakers.
11. Memory preset buttons: To set a station: Select frequency band AM/FM, tune to a station, press and hold a preset button until sound returns.
12. Shuffle (CD): Press to play tracks in random order. Press again to disable.
13. Compression (CD): Press to bring soft and loud passages together for a more consistent listening level. Press again to disable.
14. Works in tape mode only. Reduces tape noise and hiss; press to activate/deactivate.
The Dolbynoise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolbyand the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation.
15. Side 1–2: Works in tape mode only. Press to play reverse side of the tape.
/ to shift sound to the
/ to shift sound to the
Dolbynoise reduction:
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
19
Page 20
Entertainment Systems
16. Fast Forward (FF): Press for a slow advance, press and hold for a fast advance. Press again to disable.
17. Rewind (REW): Press for a slow rewind, press and hold for a fast rewind. Press again to disable.
18. Select (SEL): Use with Bass, Treble, Balance and Fade controls.
19. Bass: Press BASS; then press SEL
/ to decrease/increase
the bass output.
Treble: Press TREB; then press SEL
/ to decrease/increase
the treble output.
20. Tune: Works in radio mode only. Press TUNE
/ to change
frequency down/up.
FF
2
SEEK
TUNE
REW
1
SEL
21. Seek: Press and release SEEK
/ for previous/next
strong station, selection or track.
22. AM/FM: Press to select AM/FM1/FM2 frequency band.
20
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
SEEK
TUNE
Page 21
Entertainment Systems
PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED)
1. Seek: Press and release SEEK strong station, or track of current
disc.
2. Rewind: Press for a slow rewind, press and hold for a fast rewind.
/ for previous/next
Fast forward: Press for a slow advance, press and hold for a fast advance.
3. Comp (Compression): In CD mode, press to adjust the soft and loud passages together for a more consistent listening level. Press the COMP control until COMP ON is displayed.
4. Mute: Press to MUTE playing media; press again return to playing media. In CD mode, MUTE acts as a pause feature.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
21
Page 22
Entertainment Systems
5. Eject: Press to eject a CD. EJECTING # (desired selection) will appear on the display. When the CD appears in the CD slot for removal, the display reads REMOVE CD # (desired selection). Press and hold to eject all loaded discs.
6. Bass: Press BASS; then press SEL the bass output.
Treble: Press TREB; then press SEL the treble output.
7. Select: Use with Bass, Treble, Balance and Fade controls to adjust levels. Use with MENU to set the clock and engage RDS.
8. Balance: Press BAL; then press SEL left/right speakers.
Fade: Press FADE; then press SEL rear/front speakers.
9. Menu: Press MENU and SEL to access clock mode, RDS on/off, Traffic, Program type, Show type and Compression modes.
Traffic: Allows you to hear traffic broadcasts. With the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it is broadcasting RDS data). Traffic information is not available in most
U.S. markets.
FIND Program type: Allows you to search RDS-equipped stations for a certain category of music format: Classic, Country, Info, Jazz, Oldies, R&B, Religious, Rock, Soft, Top 40.
Show TYPE: Displays the stations call letters and format.
Compression: Brings soft and loud CD passages together for a more
consistent listening level.
/ to decrease/increase
/ to decrease/increase
/ to shift sound to the
/ to shift sound to the
22
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 23
Entertainment Systems
Setting the clock: Press MENU until SELECT HOUR or SELECT MINS is displayed. Use SEL to manually increase ( hours/minutes. Press MENU again to disengage clock mode.
10. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. In CD mode, press to move between CDs. This radio is equipped with six station memory preset controls which allow you to set up to six AM stations and 12 FM stations (six in FM1 and six in FM2).
11. CD: Press to select CD mode.
Seamless play: In CD mode, the transition between the end of one CD and the beginning of another will not contain delay time unless SEEK or a preset control is pressed.
12. AM/FM: Press to select a frequency band in radio mode.
Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press and momentarily hold AM/FM. AUTOSET will flash on the display. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets. Press again to disengage.
13. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels.
) or decrease ( ) the
14. Load: Press to load a CD. SELECT SLOT will appear in the display. Select from 1–6onthe memory presets. MOVING TO # and then LOAD CD# will appear in the display. Insert the CD into the system, label side up. Press and hold to load up to six discs.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
23
Page 24
Entertainment Systems
15. Shuffle: Press to play tracks in random order. Press SHUF to cycle through SHUF TRAC, SHUF DISC or SHUF OFF.
16. Scan: Press to hear a brief sampling of all listenable stations or CD tracks. Press again to stop.
17. Disc/Tune: Radio: Press or to manually tune down or up
the frequency band. CD: Press
18. CD door: Insert a CD label side up.
REAR AUDIO CONTROLS (IF EQUIPPED)
The rear seat controls allow the middle seat passengers to operate the radio, tape, CD or CD changer (if equipped).
To engage, simultaneously press the memory preset controls 3 and 5. Press again to disengage.
1. Memory: Push successively to allow rear seat passengers to scroll through memory presets. Push in CD changer mode (if equipped) to advance to the next disc.
2. Seek: Press the previous or next station,
selection or track.
3. Headphone jack: Plug a 3.5 mm headphone into the jack.
4. Headphone/speaker: Press to turn all speakers off (headphone mode). Press again to deactivate the headphone and activate system speakers.
5. Volume: Press + to increase and to decrease volume levels. From the rear seat controls, volume cannot be set higher than the front seat setting.
6. Media: Push to toggle between AM, FM1, FM2, tape, CD or CD changer mode (if equipped).
or to select the previous or next track on the CD.
or to access
5
VOLUME MEDIA
4
MEM
2631
SEEK
24
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 25
Entertainment Systems
RADIO FREQUENCIES
AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are:
AM - 530, 540–1700, 1710 kHz
FM- 87.7, 87.9–107.7, 107.9 MHz
RADIO RECEPTION FACTORS
There are three factors that can affect radio reception:
Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception.
Terrain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception.
Station overload: When you pass a broadcast tower, a stronger signal may overtake a weaker one and play while the weak station frequency is displayed.
CASSETTE/PLAYER CARE
Do:
Use only cassettes that are 90 minutes long or less.
Tighten very loose tapes by inserting a finger or pencil into the hole
and turning the hub.
Remove loose labels before inserting tapes.
Allow tapes which have been subjected to extreme heat, humidity or
cold to reach a moderate temperature before playing.
Clean the cassette player head with a cassette cleaning cartridge after 10–12 hours of play to maintain good sound/operation.
Dont:
Expose tapes to direct sunlight, extreme humidity, heat or cold.
Leave tapes in the cassette player for a long time when not being
played.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
25
Page 26
Entertainment Systems
CD/CD PLAYER CARE
Do:
Handle discs by their edges only. Never touch the playing surface.
Inspect discs before playing. Clean only with an approved CD cleaner
and wipe from the center out.
Dont:
Expose discs to direct sunlight or heat sources for extended periods of time.
Insert more than one disc into each slot of the CD changer magazine.
Clean using a circular motion.
CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ball point pens may damage CDs. Please contact your dealer for further information.
AUDIO SYSTEM WARRANTY AND SERVICE
Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician.
REAR SEAT ENTERTAINMENT DVD SYSTEM (IF EQUIPPED)
Your vehicle may be equipped with a Rear Seat Entertainment DVD System which allows you to watch DVDs, play music CDs and to plug in and play video game systems. Please review this material to become familiar with the system features and safety information.
26
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 27
Entertainment Systems
DVD player controls
1. MAIN control
NEXT Press to access the next track on the CD, the next chapter on the DVD, or to go up in cursor mode.
PREV Press to access the previous track on the CD, the previous chapter on the DVD, or to go down in cursor mode.
REV Press to reverse in CD and DVD play modes or to move the cursor left in the menu active mode.
FWD Press to advance in CD and DVD play modes or to move the cursor right in the menu active mode.
2. PLAY/PAUSE control
Press to playback or pause the DVD.
3. DIM control
Adjust to increase (+) or decrease (-) the amount of brightness on the screen.
4. ENTER control
Press to select the function pointed to within the active menu. May also be used by some user interactive discs during movie play.
5. MENU control
Press to bring up the disc menu.
6. AUX control
Press to switch DVD player from play mode to auxiliary mode.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
27
Page 28
Entertainment Systems
7. Auxiliary jacks
Insert lines for standard video game players.
8. STOP/EJECT control
Press once to stop DVD play. Press again to eject the DVD.
9. DISPLAY (DISP) control
Press to enable on screen display of player menu and user display adjustments.
DVD control features
Menu control
Press the MENU control to enter into MENU mode. This allows you to move and choose within the DVD generated menu structure. Once in MENU mode:
Press the NEXT control to move the cursor one position upward
Press the PREV control to move the cursor one position downward
REV
REV
NEXT
PREV
NEXT
PREV
FWD
FWD
Press the REV control to move the cursor left one position
Press the FWD control to move the cursor right one position
28
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
REV
REV
NEXT
PREV
NEXT
PREV
FWD
FWD
Page 29
Entertainment Systems
Next/Previous control
The NEXT (up) and PREV (down) controls allow you to access the next or previous track on a CD or chapter on a DVD. When pressed, the playing audio will mute momentarily while the next chapter is accessed. Press and hold to advance or reverse multiple tracks or chapters.
REV/FWD control
Press the REV/FWD control during playback mode to reverse or advance at a normal speed. Press the REV/FWD control again to disengage the reverse/advance action and return to normal playback mode
Enter control
The ENTER control allows you to select items when in MENU mode.
Press the ENTER control to select the desired highlighted item.
CD play mode
Press NEXT during CD play to advance to the next track. If you press NEXT during the last track, the system will wrap around to the first track and begin play.
REV
REV
REV
NEXT
FWD
PREV
NEXT
FWD
PREV
ENTER
NEXT
FWD
PREV
Slow play mode
To enter slow play mode, press the PLAY/PAUSE control. Once the system is in pause mode, press the FWD or REV control for slow motion playback. Three different speeds are available depending on how long the control is held. Press the control once for slow motion playback. Press the control again to disengage slow motion playback. Press the PLAY/PAUSE control to return to normal playback mode.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
29
Page 30
Entertainment Systems
User menu mode
To adjust the display setting, press DISP once and the player menu will appear. Press DISP again to adjust the display setting. Use the arrow controls and the ENTER controls to select the various screen settings. (Available screen selections are 16x9, Normal, 4x3 and Zoom).
The DVD player will read the disc type and configure the display accordingly. Some movies have a wide screen movie format to fit a normal 4x3 screen. In this case, the movie will have black bars on the top and bottom. When shown on the screen, it may appear as a small screen within the wide screen. It may be desirable to view this type of movie in zoom mode. To enter zoom mode, press DISP once for the player menu and again to adjust the display setting. Select zoom from the screen settings by using the arrow and ENTER controls.
Remote control
1
2
DISP
REV
+
8
-
MNU
MODE
FWD
SEEKVOL
DISP
ENT
MEMORY
7
1. REWIND control
Press to reverse the direction of the DVD movie.
2. FAST FORWARD control
Press to advance the direction of the DVD movie.
3. PLAY/STOP control
Press to play or stop the DVD movie.
30
3
4
5
6
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 31
Entertainment Systems
4. SEEK control
Press to reverse or advance the chapter of the DVD or the track of the CD.
5. DISPLAY (DISP) control
Press to enable on screen display of player menu and user display adjustments. Once the display is on, use SEEK to choose the desired screen setting.
6. ENTER (ENT) MEMORY control
In DVD playback mode, press the control to select a designated item in menu mode.
In stop mode, press the control to select the next radio memory preset.
7. MNU/MODE control
In DVD playback mode, press to access the disc menu.
In stop mode, press to change to a different playing media (e.g. AM, FM, CD...)
8. VOLUME control
Press to increase (+) or decrease (-) volume level.
Battery replacement
Batteries are supplied with the remote control unit. Since all batteries have a limited shelf life, replace them when the unit fails to control the DVD player. There is a LED indicator light on the remote control that will illuminate when any control is pressed.
Slide the battery cover off as shown on the remote control to access the batteries.
The remote control unit uses two AAA batteries.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
31
Page 32
Entertainment Systems
Rear seat controls
The rear seat controls allow the rear seat passengers to operate the radio, tape, CD, DVD or AUX (if equipped).
Adjusting the volume from the rear seat controls
The volume control allows the rear seat passengers to adjust the volume level of the desired selection.
Press the + control to increase the volume. Press the - control to decrease the volume.
When in single play mode, the speaker volume cannot be set higher than the current volume radio setting. When using wired headphones, (dual play mode), the rear seat controls can change the volume setting to any desired level.
Mode select
Press MEDIA to toggle between AM, FM1, FM2, TAPE, CD, DVD and AUX modes (if equipped). When selected, the media source will illuminate in the radio display.
VOLUME MEDIA
VOLUME MEDIA
VOLUME MEDIA
MEM
MEM
MEM
SEEK
SEEK
SEEK
AM
AM radio frequency band
FM1, FM2
FM radio frequency bands
TAPE
cassette tape (if equipped)
CD
single CD player (if equipped)
in-dash six CD player (if equipped)
32
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 33
Entertainment Systems
DVD/AUX
DVD player / Auxiliary line input (if equipped)
Memory preset control
In radio mode, press the MEMORY control successively to scroll through the memory presets in AM, FM1 or FM2.
If your vehicle is equipped with an in-dash six CD player, press the MEMORY control to select the next disc in the compact disc changer. Play will begin with the first track.
Seek function
The SEEK control has varying functions depending on which mode is enabled.
In radio mode (AM, FM1, FM2):
Press the
control to find the next station down the frequency band.
VOLUME MEDIA
VOLUME MEDIA
MEM
MEM
SEEK
SEEK
Press the
In tape mode (if equipped), press the selection or
In single CD mode (if equipped), press the previous track or
If equipped with an in-dash six CD player, press the
control to find the next station up the frequency band.
control to access the previous
for the next selection.
control to access the
for the next track.
control to
access the previous track or to select the next track of the current disc.
In AUX/DVD mode, the SEEK control is not operational.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
33
Page 34
Entertainment Systems
Using wired headphones/Personal Audio Feature
Single play mode will allow all passengers to listen to the same media source through all speakers. The Personal Audio Feature (dual play) allows the front seat passengers to listen to one source (radio, TAPE, CD, DVD, or AUX) while the rear seat passengers listen to another. However, front and rear seat passengers cannot listen to two different radio stations simultaneously.
VOLUME MEDIA
MEM
SEEK
To activate from the rear seat controls, press the plug a 3.5mm headphone into the headphone jack. With the headphones
ON, the rear speakers will not operate. In this mode, the headphones are enabled (dual play mode). The rear seat passengers have control over the desired volume levels.
Press the MEDIA control to toggle to the desired media source.
Use the SEEK, VOLUME and MEM controls to make any desired adjustments.
Press the deactivate the Personal Audio Feature. In this mode, you can adjust the
audio output to all system speakers front and rear together. The rear seat passengers cannot raise the volume of the system above the level on the front radio bezel.
Parental control
Your Entertainment System allows you to have control over the rear seat controls. The DVD system is automatically activated when the ignition is ON. This enables rear seat passengers to utilize the Rear Seat Controls
(RSC). Once the headphone mode is activated, the appear in the radio display.
Press the memory preset controls 3 and 5 simultaneously on the front audio controls to disable the rear seat controls. They will remain disabled until the front seat passengers enablethem again by simultaneously pressing the 3 and 5 preset controls. The settings of the front seat controls will always override those of the rear seat controls.
/ control again to engage the rear speakers and
/ control and
symbol will
34
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 35
Entertainment Systems
Press the memory preset controls 2 and 4 simultaneously to toggle
1 2 3 4 5 6
between single play and the Personal Audio Feature.
Wireless headphones (for DVD system only)
Your system is equipped with 2 sets of wireless headphones. (Two AAA batteries are needed to operate the headphones.) Batteries are included.
To install the batteries, lightly press down on the top of the left earpiece and slide the cover off.
When replacing the batteries, use two new batteries (alkaline recommended) and install them with the correct (+) and (-) orientation.
Wireless headphone operation
To operate the headphones:
Press the ON/OFF button on the left-hand earpiece. The LED light on the right-hand earpiece will illuminate. Press again to turn off.
Adjust the headphones to comfortably fit your head.
Adjust the volume control to a comfortable listening level.
ON OFF
ON OFF
Note: The volume level of the wireless headphones can only be controlled by the thumbwheel. Neither the remote control nor the rear seat controls will affect the volume output of the wireless headphones.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
35
Page 36
Entertainment Systems
When not using the headphones, shut them off to preserve battery power. The headphones will automatically turn off after five minutes if they have not received an infrared audio signal from the overhead pod.
Ensure that the line of sight between the headphone and infrared transmitter (mounted on the DVD housing) is not obstructed.
Liquid Crystal Display (LCD) flip-down screen
The screen rotates down to view and into the housing to store when not in use. Be sure the screen is latched into the housing when being stored.
ER
OW P
VOL
1. 7.0(diagonal) active matrix liquid crystal display (LCD) screen.
2. Screen housing.
3. Dimmer switch. Press +/- to increase/decrease the brightness of the
screen.
36
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 37
Entertainment Systems
Playback and format
The DVD player of your Rear Seat Entertainment DVD System can only be used in the playbackmode. (The DVD player does not offer a record feature.)
The system plays standard CDs or DVDs.
The DVD player is only capable of playback of DVDs and CDs. The
player is not compatible with CDR/RW media.
Rear Seat Entertainment DVD System protection circuits
High temperature sensor circuit
Excessively high temperatures may cause damage to the DVD player.
When the temperature of the DVD player becomes too hot, the high
temperature sensor circuit stops machine operation. DVD/CD HOT will illuminate in the radio display.
The DVD player will remain inactive until it cools to a normal operating temperature. Length of time to cool will vary depending on conditions.
General operating tips
When the engine is not running, use the system sparingly. Otherwise, it will run the battery down.
When the ignition is turned to OFF, the Rear Seat Entertainment DVD System is also turned OFF. When the ignition is turned ON, the system will begin playback from the last selected media source when the play control is pressed.
To disable the DVD player, simultaneously press the 3 and 5 memory presets on the radio face. To enable the DVD player again, press the 3 and 5 presets simultaneously.
The DVD player is only capable of reading the bottom side of a disc. When inserting a single sided disc, the label should be up. For a multi-sided disc, the desired play side should be down when the disc is inserted into the player.
The DVD player is only capable of playback of DVDs and CDs. The player is not compatible with CDR/RW media.
DVDs are formatted by regions. This DVD system can only play region 1 DVDs (DVDs manufactured for U.S. and Canada).
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
37
Page 38
Entertainment Systems
This unit is designed to play commercially pressed 12 cm (4.75 in) audio compact discs and DVDs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford DVD/CD players. Irregular shaped discs, discs with a scratch protection film attached, and discs with homemade paper (adhesive) labels should not be inserted into the player. The label may peel and cause the disc to become jammed. It is recommended that homemade discs be identified with permanent felt tip marker rather than adhesive labels. Ball point pens may damage discs. Please contact your dealer for further information.
Inserting a CD/DVD
Inserting a CD/DVD into the DVD player automatically turns the power ON and playback should begin.
The counter is automatically reset to 0:00:00.
Removing a CD/DVD
1. Press the STOP/EJECT control to stop playback.
2. Press the STOP/EJECT control again to eject the CD/DVD.
If the CD/DVD is not removed within the allotted time, the system will pull the CD/DVD back into the system for safety purposes. If the CD/DVD will not eject from the system, press and hold the EJECT control for approximately 2 seconds. The disc should eject whether the vehicle ignition is ON or OFF.
Playing a video game/auxiliary device
1. Connect the video line from your video game device to the YELLOW
auxiliary input jack.
2. Connect the left and right audio lines to the WHITE and RED auxiliary
input jacks respectively.
3. Press the MODE control until DVD/CD AUX (no disc in player) or
DVD/CD play (disc in player) illuminates in the radio display. If a disc is in the system, playback should begin. To enable the aux inputs, press the STOP control or press the AUX control on the DVD player.
38
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 39
Entertainment Systems
On-screen indicators
Each time a control is pressed, the operational status of the DVD player is shown on the screen. The following are some possible indicators:
1. CD track
2. DVD chapter
3. SYSTEM COUNTER displays current viewing time of desired media.
(HOURS:MINUTES:SECONDS)
4. DVD/ CD STATUS (PLAY/FF/REW/PAUSE)
5. AUDIO OUTPUT (not changeable)
6. Subtitles (specific language type - English or Spanish, dependent on
disc capability and ON/OFF selection.)
7. Camera angle (of picture) - Adjustable with cursor controls and
ENTER control.
Safety information
Read all of the safety and operating instructions before operating the system and retain for future reference.
Do not attempt to service, repair or modify the Rear Seat Entertainment DVD System. See your Ford or Lincoln Mercury dealer.
Do not insert foreign objects into the DVD compartment.
The front glass on the liquid crystal display (LCD) flip-down
screen may break when hit with a hard surface. If the glass breaks, do not touch the liquid crystalline material. In case of contact with skin, wash immediately with soap and water.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
39
Page 40
Entertainment Systems
Do not expose the liquid crystal display (LCD) flip-down screen to direct sunlight or intensive ultraviolet rays for extensive periods of time. Ultraviolet rays deteriorate the liquid crystal.
Be sure to review User Manuals for video games and video game equipment when used as auxiliary inputs for your Rear Seat Entertainment DVD System.
Do not operate video games or video equipment if the power cords and/or cables are broken, split or damaged. Carefully place cords and/or cables where they will not be stepped on or interfere with the operation of seats and/or compartments.
Disconnect video games and video equipment power cords and/or cables when not in use.
Avoid touching auxiliary input jacks with your fingers. Do not blow on them or allow them to get wet or dirty.
Do not clean any part of the DVD player with benzene, paint thinner or any other solvent.
Federal Communication Commission (FCC) Compliance
Changes or modifications not approved by Ford Lincoln Mercury could void users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.
Care and service of the DVD player
Environmental extremes
DVD players that are subjected to harsh environmental conditions may be damaged or perform at less than maximum capability. To avoid these outcomes, whenever possible avoid exposing your DVD player to:
extremely hot or cold temperatures.
direct sunlight.
40
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 41
Entertainment Systems
high humidity.
a dusty environment.
locations where strong magnetic fields are generated.
Temperature extremes
When the vehicle is parked under direct sunlight or in an extremely cold place for a long period of time, wait until the cabin temperature of the vehicle is at normal temperature before operating the system.
Humidity and moisture condensation
Moisture in the air will condense in the DVD player under extremely humid conditions or when moving from a cold place to a warm one. If moisture condensation occurs, do not insert a CD or DVD into the player. If one is already in the player, remove it. Turn the DVD player ON to dry the moisture before inserting a DVD. This could take an hour or more.
Cleaning the liquid crystal display (LCD) flip-down screen
Clean the display screen by applying a small amount of water or any ammonia-based household glass cleaner directly to a soft cloth. Rub the screen gently until the dust, dirt or fingerprints are removed. Do not spray the screen directly with water or glass cleaning solvents. Overspray from these fluids could drip down into the internal electronics of the screen and cause damage. Do not apply excessive pressure while cleaning the screen.
Foreign substances
Exercise care to prevent dirt and foreign objects from entering the DVD player compartment. If liquid is accidentally spilled onto the system, immediately turn the system OFF and consult a qualified service technician.
Cleaning compact discs
Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion.
Cleaning the DVD player
Clean the exterior of the DVD player with a damp cloth. Do not use CD cleaning kits or CDs intended to clean the interior of your DVD player. Use of these products may damage your system.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
41
Page 42

Climate Controls

Climate Controls
HEATER ONLY SYSTEM (IF EQUIPPED)
1. Fan speed adjustment: Controls the volume of air circulated in the vehicle.
2. Temperature selection: Controls the temperature of the airflow in the vehicle.
3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control.
: Distributes outside air through the instrument panel vents.
OFF: Outside air is shut out and the fan will not operate.
: Distributes outside air through the instrument panel vents and the
floor vents.
: Distributes outside air through the floor vents.
: Distributes outside air through the windshield defroster vents and
floor vents.
: Distributes outside air through the windshield defroster vents.
Operating tips
To reduce fog build up on the windshield during humid weather, place the air flow selector in the
To reduce humidity build up inside the vehicle during cold or warm weather, do not drive with the air flow selector in the OFF position.
Under normal weather conditions, do not leave the air flow selector in OFF when the vehicle is parked. This allows the vehicle to breathe using the outside air inlet vents.
Do not put objects under the front seats that will interfere with the air flow to the back seats.
Remove any snow, ice or leaves from the air intake area at the base of the windshield.
To aid in side window defogging/demisting in cold weather:
1. Select
2. Set the temperature control to full heat
3. Set the fan speed to HI
4. Direct the outer instrument panel vents towards the side windows
To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.
42
position.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 43
Climate Controls
Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.
MANUAL HEATING AND AIR CONDITIONING SYSTEM
1. Fan speed adjustment: Controls
the volume of air circulated in the vehicle.
2. Temperature selection:
Controls the temperature of the airflow in the vehicle.
3. Air flow selections: Controls the direction of the airflow in the
vehicle. See the following for a brief description on each control. MAX A/C: Uses recirculated air to cool the vehicle. Air flows from the
instrument panel vents only. A/C: Uses outside air to cool the vehicle. Air flows from the instrument
panel vents only.
: Distributes outside air through the instrument panel vents.
OFF: Outside air is shut out and the fan will not operate.
: Distributes outside air through the instrument panel vents and the
floor vents.
: Distributes outside air through the floor vents.
: Distributes outside air through the windshield defroster vents and
floor vents.
: Distributes outside air through the windshield defroster vents.
Operating tips
To reduce fog build up on the windshield during humid weather, place the air flow selector in the
To reduce humidity build up inside the vehicle: do not drive with the air flow selector in the OFF or MAX A/C position.
Do not put objects under the front seats that will interfere with the airflow to the back seats.
Under normal weather conditions, do not leave the air flow selector in MAX A/C or OFF when the vehicle is parked. This allows the vehicle to breatheusing the outside air inlet vents.
Remove any snow, ice or leaves from the air intake area at the base of the windshield.
position.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
43
Page 44
Climate Controls
To aid in side window defogging/demisting in cold weather:
1. Select
2. Select A/C.
3. Set the temperature control to maintain comfort.
4. Set the highest fan speed
5. Direct the outer instrument panel vents towards the side windows.
To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.
ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (EATC) SYSTEM
.
Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.
A/C
EXT TEMP
F
AUTO
OFFAUTO
1. A/C: Press to turn on the air
conditioning in all modes except
2. Recirculated air: Reduces cool
down time in very hot conditions by recirculating the cabin air. May also help keep undesired odors from entering the vehicle.
3. Defrost:
Press to defrost
the windshield.
44
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 45
Climate Controls
4. Fan speed: Press to manually
increase or decrease fan speed. When in AUTO mode, will be controlled automatically to meet the desired temperature.
5.
defroster and floor vents.
6.
7.
panel and floor vents.
8.
vents and the floor vents.
9. OFF: Press to turn the system
off.
10. Manual override controls:
Press any of these controls to leave automatic mode and to manually determine where airflow is directed. To return to full automatic control, press AUTO.
11. AUTO: Press to engage
automatic mode. The system will determine fan speed, airflow location, and outside or recirculated air depending on the selected temperature. Fan speed will remain automatic unless the fan control is pressed to manually adjust.
12. EXT TEMP: Press to display
the outside temperature. Will remain in the display until pressed again.
13. Temperature controls: Press
to manually increase or decrease the desired temperature. In automatic mode, the system will to heat or cool the vehicle to the selected temperature.
(Floor/defrost): Distributes outside air through the windshield
(Floor): Distributes outside air through the floor vents.
(Panel/floor): Distributes outside air through the instrument
(Panel): Distributes outside air through the instrument panel
Operating tips
To reduce fog build up on the windshield during humid weather, place the air flow selector in the
position.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
45
Page 46
Climate Controls
To reduce humidity build up inside the vehicle: do not drive with the air flow selector in the OFF or MAX A/C position.
Do not put objects under the front seats that will interfere with the airflow to the back seats.
Under normal weather conditions, do not leave the air flow selector in MAX A/C or OFF when the vehicle is parked. This allows the vehicle to breatheusing the outside air inlet vents.
Remove any snow, ice or leaves from the air intake area at the base of the windshield.
To aid in side window defogging/demisting in cold weather:
1. Select
2. Select A/C.
3. Set the temperature control to maintain comfort.
4. Set the highest fan speed
5. Direct the outer instrument panel vents towards the side windows.
To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.
AUXILIARY SYSTEM (IF EQUIPPED)
Your vehicle may be equipped with auxiliary climate controls. These allow the front or rear seat passengers to control airflow direction, temperature and fan level of the rear compartment to quickly heat or cool the entire vehicle.
Front auxiliary controls:
.
Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.
1. Fan control: Determines fan
speed levels. Turn to REAR to give rear seat passengers control of the rear auxiliary controls. Otherwise, the front controls will determine the settings for the entire vehicle cabin. If set to OFF, the front and rear auxiliary controls will not function.
2. Temperature control:Determines temperature level. If the main
climate control system is cooling in MAX A/C or auxiliary controls will not function as the entire vehicle will operate at a full cool temperature.
46
mode, the
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 47
Climate Controls
3. Airflow control: FLOOR directs air to the floor of the third row
seating. PANEL directs air to the overhead registers of the second and third row seating. To blend the airflow, select any position between PANEL and FLOOR.
Rear auxiliary controls:
Once the front auxiliary control is set to REAR, the rear seat passengers may use the rear auxiliary controls in the overhead console to make the desired adjustments.
1. Fan control: Determines fan
speed levels.
2. Temperature control:
Determines temperature levels. If the main climate control system is cooling in MAX A/C or the auxiliary controls will not function as the entire vehicle will operate at a full cool temperature.
3. Airflow control:FLOOR directs air to the floor of the third row
seating. PANEL directs air to the overhead registers of the second and third row seating. To blend the airflow, select any position between PANEL and FLOOR.
REAR WINDOW DEFROSTER
The rear defroster control is located on the instrument panel and works to defrost your rear window from fog and ice.
Ensure that the ignition is ON position. Press to turn the defroster ON/OFF. The indicator light will illuminate when ON.
Do not use razor blades or other sharp objects to clean the inside of the rear window or to remove decals from the inside of the rear window. This may cause damage to the heated grid lines and will not be covered by your warranty.
mode,
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
47
Page 48

Lights

Lights
HEADLAMP CONTROL
Turns the lamps off.
Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps.
Turns the headlamps on.
Autolamp control (if equipped)
The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
The autolamp system also keeps the lights on for approximately 20 seconds after the ignition switch is turned to OFF.
To change the delay time of the autolamp feature, do the following:
1. Start with the ignition in OFF and the autolamps selected.
2. Deselect the autolamps.
3. Put the ignition in RUN.
4. Put the ignition in OFF.
5. Select the autolamps. Steps 2 through 5 must be performed within a 10 second period. At this point, the headlamps and parking lamps will turn on.
6. Deselect the autolamps after the desired autolamp delay time (maximum of 3 minutes). At this point, the headlamps and parking lamps will turn off.
A
A
48
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 49
Lights
Foglamp control (if equipped)
The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp
control is in the position and the high beams are not
turned on.
In autolamp mode, the foglamps wont be operational until lighting conditions warrant the activation of the headlamp/parklamp lighting.
Pull headlamp control towards you to turn foglamps on. The foglamp indicator light parklamps are on.
Daytime running lamps (DRL) (if equipped)
Turns the headlamps on with a reduced output.
To activate:
the ignition must be in the ON position,
the headlamp control is in the OFF or parking lamp and
the parking brake must be disengaged.
Always remember to turn on your headlamps at dusk or during
inclement weather. The Daytime Running Lamp (DRL) system does not activate with your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
, or
will illuminate when the switch is pulled and the
A
High beams
Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
49
Page 50
Lights
Flash to pass
Pull toward you slightly to activate and release to deactivate.
PANEL DIMMER CONTROL
Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation.
Move the control to the full upright position, past detent, to turn on the interior lamps.
AIMING THE HEADLAMPS
The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician.
TURN SIGNAL CONTROL
Push down to activate the left turn signal.
Push up to activate the right turn signal.
50
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 51
INTERIOR LAMPS
Dome/Map lamps (if equipped)
The map lamps and controls are located on the dome lamp. Press the controls on either side of each map lamp to activate the lamps.
Rear courtesy/reading lamps
Second row courtesy/reading lamp
Third row courtesy/reading lamp
Lights
The courtesy lamps light when:
any door is opened.
the instrument panel dimmer switch is held up until the courtesy
lamps come on.
any of the remote entry controls are pressed and the ignition is OFF.
The reading lamps can be turned on by pressing the rocker control.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
51
Page 52
Lights
Rear dome lamp
The dome lamp lights when:
any door is opened (and switch is in middle position).
the instrument panel dimmer switch is held up until the courtesy lamps come on.
any of the remote entry controls are pressed and the ignition is OFF (and switch is in the middle position).
With the ignition key in the ACC or ON position, the rear dome lamp can be turned ON or OFF by sliding the control.
BULBS
Replacing exterior bulbs
Check the operation of all the bulbs frequently.
Using the right bulbs
Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized D.O.T.for North America and an Efor Europe to assure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
Function Number of
bulbs
Headlamps 2 9007 Park/turn lamp 2 3157 AK Sidemarker lamp 2 194 Foglamp 2 9145 Tail/stop lamp 2 3157 K Backup lamp 2 3156K High-mount brakelamp 3 912 Rear dome lamp 1 921 Map/dome lamp 2 578
52
Trade number
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 53
Lights
Function Number of
bulbs
Second row reading lamp 2 578 Third row reading lamp 2 211-2 License lamp 2 194 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer
Interior bulbs
Check the operation of all bulbs frequently.
Replacing headlamp bulbs
1. Make sure that the headlamp control is in the OFF position then open
the hood.
2. Disconnect the electrical
connector from the bulb by pulling rearward.
3. Remove bulb retainer ring by
turning it counterclockwise, then slide the ring off the plastic base.
4. Pull the bulb out of headlamp
assembly.
Trade number
Handle a halogen headlamp bulb carefully and keep out of
childrens reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Install the new bulb(s) in reverse order.
Replacing front parking/turn signal bulbs
1. Make sure headlamp switch is in the OFF position, then open the hood.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
53
Page 54
Lights
2. Remove the two screws and carefully pull the parking lamp/turn signal assembly from the vehicle.
3. Rotate bulb socket counterclockwise and remove it from lamp assembly.
4. Pull the bulb straight out of the socket.
Install the new bulbs in reverse order.
54
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 55
Replacing foglamp bulbs
1. Make sure the headlamp switch is in the OFF position and then rotate the foglamp bulb counterclockwise and remove from foglamp (the rear side of the foglamp is shown).
2. Disconnect the electrical connector from the foglamp bulb.
Install the new bulb in reverse order.
Replacing tail lamp/turn/backup lamp bulbs
1. Make sure the headlamp switch is in the OFF position and remove the four screws and the lamp assembly from vehicle.
Lights
2. Rotate bulb socket counterclockwise and remove from lamp assembly.
3. Carefully pull the bulb straight out of the socket.
Install the new bulb(s) in reverse order.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
55
Page 56
Lights
Replacing high-mount brakelamp bulbs
1. Make sure the headlamp switch is in the OFF position and remove the two screws and then the lamp assembly.
2. Remove the bulb socket from lamp assembly and pull the bulb straight out.
Install the new bulb(s) in reverse order.
Replacing license plate lamp bulbs
1. Make sure the headlamp switch is in the OFF position and reach behind the rear bumper to locate the bulb socket.
2. Twist the socket counterclockwise and remove.
3. Pull the old bulb straight out.
Install the new bulb in reverse order.
56
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 57

Driver Controls

Driver Controls
MULTI-FUNCTION LEVER
Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.
Speed dependent wipers: When the wiper control is on, the speed of the wipers will automatically adjust with the vehicle speed. The faster your vehicle is travelling the faster the wipers will go.
Windshield washer: Push the end of the stalk:
briefly: causes a single swipe of the wipers without washer fluid.
a quick push and hold: the wipers will swipe three times with washer fluid.
a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.
Rear window wiper/washer controls
For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select:
INT 1 3.5 second interval rear wiper.
INT 2 10.5 second interval rear wiper.
OFF Rear wiper and washer off.
For rear wash cycle, rotate (and hold as desired) the rear wiper/washer control to either
From either position, the control will automatically return to the INT2 or OFF position.
position.
57
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 58
Driver Controls
Changing the wiper blades
1. Pull the wiper arm away from the
vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
2. Attach the new wiper to the
wiper arm and press it into place until a click is heard.
3. Replace wiper blades every 6 months for optimum performance.
TILT STEERING WHEEL
To adjust the steering wheel:
1. Pull and hold the steering wheel
release control toward you.
2. Move the steering wheel up or
down until you find the desired location.
3. Release the steering wheel
release control. This will lock the steering wheel in position.
Never adjust the steering wheel when the vehicle is moving.
58
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 59
Driver Controls
TRANSMISSION CONTROL
Tow/Haul feature
(5–speed automatic transmission) (if equipped)
Gearshift lever type A
Gearshift lever type B
To activate, press the transmission control switch (TCS) located on the gearshift. The TOW/HAUL indicator light will illuminate on the gearshift lever or in the instrument cluster, depending on how your vehicle is equipped. The transmission will operate in all gears. Press the transmission control switch again to deactivate Tow/Haul mode. When you shut off and re-start your vehicle, the transmission will automatically return to normal mode with Tow/Haul feature deactivated, refer to the Driving chapter for more information.
Overdrive cancel
(4–speed automatic transmission) (if equipped)
To deactivate overdrive, press the transmission control switch (TCS) located on the gearshift. The OFF indicator light will illuminate on the gearshift. The transmission will operate in all gears except overdrive. Press the transmission control switch again to return to normal overdrive mode. When you shut off and re-start your vehicle, the transmission will automatically return to normal (Overdrive) mode.
For additional information about the gearshift and the transmission control switch operation refer to the Driving chapter.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
59
Page 60
Driver Controls
ILLUMINATED VISOR MIRROR
Lift the mirror cover to turn on the visor mirror lamps.
OVERHEAD CONSOLE
The appearance of your vehicles overhead console will vary according to your option package.
Forward storage bin (if equipped)
Press the release control to open the storage compartment. The door will open slightly and can be moved to full open.
The storage compartment may be used to secure sunglasses or a similar object.
Installing a garage door opener (if equipped)
The storage compartment can be converted to accommodate a variety of aftermarket garage door openers:
Place Velcro hook onto back side of aftermarket transmitter opposite of actuator control.
Place transmitter into storage compartment, control down.
Place the provided height adaptors onto the back of the storage bin door as needed.
Press the storage compartment door to activate the transmitter.
60
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 61
Power quarter rear windows (if equipped)
Driver Controls
When closing the power quarter rear windows, you
V
EN
VENT
T
should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.
Press the
portion of the VENT
MODE E/M
RESET
control to open the power rear quarter windows.
Press the
portion of the VENT control to close the power rear
quarter windows.
AUXILIARY POWER POINT
Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.
Do not plug optional electrical accessories into the cigarette lighter. Use the power point.
Do not use the power point for operating the cigarette lighter element.
The Maximum power each power point can supply depends on the fuse rating. For example: a 20A fuse should supply a maximum of 240 Watts, a 15A fuse should supply a maximum of 180 Watts and a 10A fuse should supply a maximum of 120 Watts. Exceeding these limits will result in a blown fuse.
Always keep the power point caps closed when not being used.
There are up to four auxiliary power points in the following locations:
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
61
Page 62
Driver Controls
Located on the instrument panel.
Located on the back side of the
center console (Accessible from the second row seats).
Located in the left side storage compartment in the third row seating position.
POWER POINT
Located on the right trim panel in the rear cargo area.
62
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 63
Driver Controls
POWER WINDOWS
When closing the power
windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.
Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window.
One touch down
Allows the drivers window to open fully without holding the control down. Press completely down on AUTO and release quickly. Press again to stop.
Window lock
The window lock feature allows only the driver to operate the power windows.
To lock out all the window controls except for the drivers press the left side of the control. Press the right side to restore the window controls.
Accessory delay (if equipped)
With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.
MIRRORS
Automatic dimming inside rear view mirror (if equipped)
Your vehicle is equipped with an inside rear view mirror with an auto-dimming function. The electronic day/night mirror will change from
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
63
Page 64
Driver Controls
the normal state to the non-glare state when bright lights (glare) reach the mirror. When the mirror detects bright light from front or behind, it will automatically adjust to minimize glare.
Press the control located on the bottom of the mirror to turn the mirror on or off. The mirror will automatically return to the normal state whenever the vehicle is placed in R (reverse)(when the mirror is on) to ensure a bright clear view when backing up.
Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.
Power side view mirrors (if equipped)
To adjust your mirrors:
1. Select L to adjust the left mirror or R to adjust the right mirror.
2. Move the control in the direction you wish to tilt the mirror.
3. Return to the center position to disable the adjust function.
Heated outside mirrors
The main mirror glass is heated automatically to remove ice, mist and fog and activates when the vehicle is started.
Note: The mirrors may be hot to the touch but will not burn. This is a normal condition.
Type A
The mirror heating elements are designed to operate regardless of the geographic location of the vehicle. There is no switch to turn on, or other operator involvement required other than to start the vehicle.
64
(if equipped)
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 65
Driver Controls
Type B
The spotter mirror, below the main mirror, is not heated and must be adjusted manually.
Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.
Mirror mounted side turn signal indicator (if equipped)
Type A
When the vehicle turn signals are activated, the mirrors will show a blinking red arrow.
The turn signal provides an additional warning to other drivers that your vehicle is about to turn.
Type B
When the vehicle turn signals are activated, the outer portion of the mirror housing will blink amber.
The turn signal feature can be seen by other drivers who may approach from the rear of the vehicle.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
65
Page 66
Driver Controls
Clearance lamps (if equipped)
Illuminates when the headlamps or parking lamps are switched on.
This provides additional visibility of your vehicle to other drivers on the road.
Fold-away mirrors
The mirrors can be manually folded forward or backwards for narrow spaces like driving through an automatic car wash or backing out of a garage with the trailer tow mirror.
The telescoping feature (if equipped) allows the mirror to extend approximately 80 mm (3.15 inches). This feature is especially useful to the driver when towing a trailer.
66
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 67
Driver Controls
POWER ADJUSTABLE FOOT PEDALS
The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position.
Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you.
The adjustment allows for approximately 71–76 mm (3 inches) of maximum travel.
Never adjust the accelerator and brake pedal with feet on the
pedals while the vehicle is moving.
SPEED CONTROL (IF EQUIPPED)
With speed control set, you can maintain a speed of 48 km/h (30 mph) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 48 km/h (30 mph).
Do not use the speed control in heavy traffic or on roads that
are winding, slippery or unpaved.
Setting speed control
The controls for using your speed control are located on the steering wheel for your convenience.
1. Press the ON control and release it.
2. Accelerate to the desired speed.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
ON
OFF
67
Page 68
Driver Controls
3. Press the SET ACCEL control and release it.
4. Take your foot off the accelerator pedal.
5. The indicator
light on the
instrument cluster will turn on.
Note:
Vehicle speed may vary momentarily when driving up and down a steep hill.
If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed.
If the vehicle speed decreases more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage.
Resuming a set speed
Press the RES/RESUME control and release it. This will automatically return the vehicle to the previously set speed. The RES/RESUME control will not work if the vehicle speed is not faster than 48 km/h (30 mph).
RES
ACCEL
COAST
RES
SET
ACCEL
COAST
SET
Increasing speed while using speed control
There are two ways to set a higher speed:
Press and hold the SET ACCEL control until you get to the desired speed, then release the control. You can also use the SET
RES
SET
ACCEL
COAST
ACCEL control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1.6 km/h (1 mph).
Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET ACCEL control.
68
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 69
Driver Controls
Reducing speed while using speed control
There are two ways to reduce a set speed:
Press and hold the COAST control until you get to the desired speed, then release the control. You can also use the COAST control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1.6 km/h (1 mph).
Depress the brake pedal until the desired vehicle speed is reached, press the SET ACCEL control.
Turning off speed control
There are two ways to turn off the speed control:
Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicles previously set speed.
Press the speed control OFF control.
Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
RES
ACCEL
COAST
RES
SET
ACCEL
COAST
ON
OFF
SET
Indicator light
This light comes on when either the SET ACCEL or RES controls are pressed. The vehicle speed must be at or above 48 km/h (30 mph). It turns off when the speed control OFF control is pressed, the brake is applied, or the ignition is turned to the OFF position.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
69
Page 70
Driver Controls
STEERING WHEEL CONTROLS (IF EQUIPPED)
These controls allow you to operate some radio and climate control features.
Radio control features
Press MODE to select AM, FM1, FM2, TAPE or CD (if equipped).
In Radio mode:
Press NEXT to select a preset station from memory.
In Tape mode:
Press NEXT to listen to the next selection on the tape.
In CD mode:
Press NEXT to listen to the next track on the disc.
In any mode:
Press VOL up or down to adjust the volume.
Climate control features
Press TEMP up or down to adjust temperature.
Press FAN up or down to adjust fan speed.
NEXT
MODE
TRIP COMPUTER (IF EQUIPPED)
The trip computer tells you about the condition of your vehicle through a constant monitor of vehicle systems. You may select display features on the trip computer for a display of status.
The appearance of your vehicles trip computer may differ depending on your vehicle’s option package, but the functions are the same.
The trip computer only operates with the ignition in the ON position. Trip computer features are as follows:
70
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 71
Driver Controls
Selectable features
English/metric display
Press this control to change the trip computer display between metric and English units.
MODE
Mode control
Each press of the MODE control will display a different feature as follows:
Average fuel economy. The display will indicate the vehicles
MODE
average fuel economy in liters/100 km (or miles/gallon) since the average fuel economy was last reset.
If you calculate your average fuel economy by dividing liters of fuel used by 100 kilometers traveled (miles traveled by gallons used), your figure may be different than displayed for the following reasons:
your vehicle was not perfectly level during fill-up
differences in the automatic shut-off points on the fuel pumps at
service stations
variations in top-off procedure from one fill-up to another
rounding of the displayed values to the nearest liter (gallon)
To reset the average fuel economy:
1. Press the MODE control repeatedly until average fuel economy is
displayed (this is the only resettable display).
E/M
RESET
E/M
RESET
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
71
Page 72
Driver Controls
2. Press the E/M and MODE
controls simultaneously. The display will illuminate the AVGindicator. While the indicator is lit, release both controls to reset the average
MODE
fuel economy.
Fuel range. This function estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel.
The DTE function will flash for 5 seconds when you have approximately:
80 km (50 miles) left before you run out of fuel
40 km (25 miles)
16 km (10 miles)
DTE is calculated using a running average fuel economy, which is based on your recent driving history of 800 km (500 miles). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected.
E/M
RESET
Outside air temperature (if equipped)
The temperature can be displayed in Centigrade or Fahrenheit by pressing the E/M control.
If the outside temperature falls
MODE
E/M
below 3°C (38°F), the display will alternate from ICEto the outside
RESET
temperature at a two second rate for one minute.
Off. In this mode the display is off.
Compass
The compass display is contained in the overhead console. The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W and NW.
72
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 73
Driver Controls
The compass heading is displayed in average fuel economy modes, fuel range modes and temperature modes.
The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy. Adjustments may need to be made to the zone and calibration of the compass.
Compass zone adjustment
1. Determine which magnetic zone
you are in for your geographic location by referring to the zone map.
2. Locate the trip computer on the
4
overhead console.
3. Turn ignition to the ON position.
5
4. Press and hold both trip
computer controls. After approximately four seconds, the trip computer will enter zone setting mode. Zone setting mode is indicated when the display lights the ZONEindicator.
5. Release both controls.
Subsequent pressing of either control will increment the zone. Press the control repeatedly until the correct zone setting for your geographic location is displayed on the trip computer.
6. To exit the zone setting mode and save the displayed zone in memory,
release both controls for greater than five seconds.
Compass calibration adjustment
Perform this adjustment in an open area free from steel structures and high voltage lines.
For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.
123
6 7 8 9 1011
MODE
E/M
RESET
15
14 13
12
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
73
Page 74
Driver Controls
1. Locate the trip computer located in the overhead console.
2. Start the vehicle.
3. Press and hold both trip
computer controls. After approximately eight seconds, the trip computer will enter CAL mode. CAL mode is indicated when the
MODE
display lights the CALindicator.
4. Release both controls. The display
will return to normal, except that the CAL indicator will remain lit until the compass is successfully calibrated.
5. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until
the CAL indicator turns off. It may take up to five circles to complete calibration.
6. The compass is now calibrated.
HOMELINKWIRELESS CONTROL SYSTEM (IF EQUIPPED)
The HomeLinkWireless Control System, located on the drivers visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most current transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.
E/M
RESET
When programming your HomeLinkWireless Control System to a garage door or gate, be sure that people and objects are out of
the way to prevent potential harm or damage.
Do not use the HomeLinkWireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLinkat: www.homelink.com or 1–800–355–3515.
Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLinkequipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelinkbuttons be erased for security purposes, refer to Programming in this section.
74
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 75
Driver Controls
Programming
Do not program HomeLinkwith the vehicle parked in the garage.
Note: Your vehicle may require the ignition switch to be turned to the
ACC position for programming and/or operation of the HomeLink.Itis also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLinkfor quicker training and accurate transmission of the radio-frequency signal.
1. Press and hold the two outside
buttons releasing only when the red light begins to flash after 20 seconds. Do not repeat step one to program additional hand-held transmitters to the remaining two HomeLinkbuttons. This will erase previously programmed hand-held transmitter signals into HomeLink.
2. Position the end of your
hand-held transmitter 2–8cm(1–3 inches) away from the HomeLink button you wish to program (located on your visor) while keeping the red light in view.
3. Simultaneously press and hold
both the HomeLinkand hand-held transmitter button. Do not release
the buttons until step 4 has been completed.
Some entry gates and garage door openers may require you to replace step 3 with procedures noted in the Gate Operator and Canadian Programmingin this section for Canadian residents.
4. The red light will flash slowly and then rapidly. Release both buttons
when the red light flashes rapidly. (The rapid flashing light indicates acceptance of the hand-held transmittersradio frequency signals.)
5. Press and hold the just-trained HomeLinkbutton and observe the red
light. If the light is a constant red, programming is complete and your device should activate when the HomeLinkbutton is pressed and released. Note: To program the remaining two HomeLinkbuttons, begin with step 2 in the Programmingsection do not repeat step 1.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
75
Page 76
Driver Controls
Note: If the red light blinks rapidly for two seconds and then turns to a continuous red, proceed with steps 6 through 8 to complete programming of a rolling code equipped device.
6. At the garage door opener receiver (motor-head unit) in the garage,
locate the learnor smartbutton (usually near where the hanging antenna wire is attached to the unit).
7. Press and release the learnor smartbutton. (The name and color
of the button may vary by manufacturer.)
Note: There are 30 seconds in which to initiate step eight.
8. Return to the vehicle and firmly press, hold for two seconds and
release the HomeLinkbutton. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming.
HomeLinkshould now activate your rolling code equipped device. To program additional HomeLinkbuttons begin with step 2 in the Programmingsection. For questions or comments, please contact HomeLink at www.homelink.com or 1–800–355–3515.
Gate Operator & Canadian Programming
During programming, your hand-held transmitter may automatically stop transmitting not allowing enough time for HomeLinkto accept the signal from the hand-held transmitter.
After completing steps 1 and 2 outlined in the Programming section, replace step 3 with the following:
Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the cyclingprocess to prevent overheating.
Continue to press and hold the HomeLinkbutton (note step 3 in the
Programmingsection) while you press and release every two seconds (cycle) your hand-held transmitter until the frequency
signal has been accepted by the HomeLink. The red indicator light will flash slowly and then rapidly after HomeLinkaccepts the radio frequency signal.
Proceed with step 4 in the Programmingsection.
76
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 77
Driver Controls
Operating the HomeLinkWireless Control System
To operate, simply press and release the appropriate HomeLinkbutton. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLinkat www.homelink.com or
1–800–355–3515.
Erasing HomeLinkbuttons
To erase the three programmed buttons (individual buttons cannot be erased):
Press and hold the two outer HomeLinkbuttons until the red indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.
HomeLinkis now in the train (or learning) mode and can be programmed at any time beginning with step 2intheProgramming” section.
Reprogramming a single HomeLinkbutton
To program a device to HomeLinkusing a HomeLinkbutton previously trained, follow these steps:
1. Press and hold the desired HomeLinkbutton. Do NOT release the
button.
2. The red indicator light will begin to flash after 20 seconds. Without
releasing the HomeLinkbutton, follow step 2 in the Programming section.
For questions or comments, contact HomeLinkat www.homelink.com or 1–800–355–3515.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
77
Page 78
Driver Controls
CENTER CONSOLE
Your vehicle may be equipped with a variety of console features. These include:
Utility compartment
Coin holder slots
Pen holder
Use only soft cups in the cupholder. Hard objects can
injure you in a collision.
Utility compartment
Pen holder
Space for lap-top computer
CELL PHONE USE
The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or otherssafety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits.
Mobile Communication Equipment includes, but is not limited to cellular phones, pagers, portable email devices, in vehicle communications systems, telematics devices and portable two-way radios.
A driver’s first responsibility is the safe operation of the vehicle.
The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road. Wait until it is safe to operate Mobile Communications Equipment.
78
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 79
Driver Controls
CARGO NET (IF EQUIPPED)
The cargo net secures lightweight objects in the cargo area. Attach the net to the anchors provided.
This net is not designed to
restrain objects during a collision.
TRIDOOR
The TriDoor area is intended for cargo storage only, not for passengers. You can open and close the TriDoors from outside the vehicle only. You cannot open the liftgate or cargo doors from inside the vehicle.
To open the liftgate, unlock the liftgate (with the key, the remote entry transmitter by pressing the UNLOCK button twice or power door locks) and pull up on the liftgate handle.
To open the cargo doors, open the liftgate, then open right cargo door first, using the handle on top of the door, then open the left cargo door using the handle on the side of the door.
For wider loads, the cargo doors can be opened wider by unhooking the check straps from the door hinge. Make sure the check straps are reattached after loading and before closing the cargo doors..
To close and lock the liftgate and cargo doors, close the left cargo door first, then the right cargo door, then pull down and close the liftgate. Lock the TriDoor with the key, remote entry transmitter or the power door lock button.
The cargo doors and liftgate should be closed before driving your
vehicle. Make sure the liftgate and/or the cargo doors are closed to prevent exhaust fumes from being drawn into the vehicle. Leaving the liftgate and/or the cargo doors open could cause serious damage to the TriDoors and its components. If you must drive with the cargo doors and liftgate window open, keep the vents open so outside air comes into the vehicle.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
79
Page 80
Driver Controls
LUGGAGE RACK
Maximum load is 90 kg (200 lbs) on the roof rack structure, or 45 kg (100 lbs) on the roof panel rails. Distribute the load equally on the cross bars.
To adjust the cross-bar position:
1. Release the latch at both ends of the cross-bar (both cross-bars are adjustable).
2. Slide cross-bar to the desired location.
3. Tighten the latch at both ends of the cross-bar.
To remove the cross-bar assembly
from the roof rack side rails:
1. Loosen the latch at both ends of the cross-bar (both cross-bars are adjustable).
2. Slide cross-bar to the end of the rail.
3. Press down on the locking feature inside the side rail and slide the cross-bar over it.
4. Slide the assemblies off the end.
Vehicles with a higher center of gravity such as utility and
four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sport cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles. Failure to drive cautiously could result in an increase risk of loss of vehicle control, vehicle rollover, personal injury and death.
80
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 81

Locks and Security

Locks and Security
KEYS
The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer.
You should always carry a second key with you in a safe place in case you require it in an emergency.
Refer to SecuriLockPassive Anti-Theft System for more information.
POWER DOOR LOCKS
Press control to unlock all doors.
Press control to lock all doors.
Smart locks (if equipped)
This feature prevents you from locking yourself out of the vehicle if your key is still in the ignition.
When you open the drivers door and you lock the vehicle with the power door locks, all the doors will lock, then the drivers door will automatically unlock reminding you that your key is still in the ignition.
The vehicle can still be locked, with the key in the ignition, using the manual lock button on the door, locking the driver’s door with a key, or by using the lock button on the remote entry transmitter (if equipped).
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
81
Page 82
Locks and Security
Childproof door locks
When these locks are set, the rear doors cannot be opened from the inside.
The rear doors can be opened from the outside when the doors are unlocked.
The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors.
Move lock control up to engage the childproof lock.
Move control down to disengage childproof locks.
REMOTE ENTRY SYSTEM
This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
The typical operating range for your remote entry transmitter is approximately 10 meters (33 feet). A decrease in operating range could be caused by:
weather conditions,
nearby radio towers,
structures around the vehicle, or
other vehicles parked next to your vehicle.
Your vehicle is equipped with a remote entry system which allows you to:
82
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 83
Locks and Security
unlock the vehicle doors without a key.
lock all the vehicle doors without a key.
activate the personal alarm.
If there is any potential remote keyless entry problem with your vehicle, ensure ALL remote entry transmitters are taken to the dealership, to aid in troubleshooting.
Unlocking the doors
1. Press and release to unlock the drivers door. Note: The interior
lamps and running board lamps (if equipped) will illuminate.
2. Press
and the liftgate.
Locking the doors
1. Press and release to lock all the doors and liftgate. The parking
lamps will flash once if all doors, the liftgate and the hood are closed and locked.
2. Press
doors and liftgate are closed and locked. Note: The doors will lock again, the horn will chirp once, and the parking lamps will flash once more.
If any of the doors, the liftgate or the hood are not properly closed, the horn will make two quick chirps.
and release again within three seconds to unlock all doors
and release again within three seconds to confirm that all the
Power door lock disable feature (if equipped)
The UNLOCK inside the vehicle when:
the ignition has been turned to the 3 (OFF) position, and
20 seconds elapse after all vehicle doors are closed and locked using
the remote entry transmitter, or the power door lock control (while the accompanying door is open).
feature on your power door locks will not work from
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
83
Page 84
Locks and Security
The UNLOCK feature will work again after:
a door has become ajar,
the ignition is turned to the 4 (ON) position,
unlocking the vehicle using the keyless entry keypad,
or using the UNLOCK
equipped).
This feature is initially deactivated, but may be activated by taking your vehicle to an authorized Ford dealer.
Sounding a panic alarm
Press (ACCESSORY) or 4 (ON) to deactivate.
Note: The panic alarm will only operate when the ignition is in the 3 (OFF) position.
Replacing the battery
The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent.
To replace the battery:
1. Twist a thin coin between the two
halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.
to activate the alarm. Press again or turn the ignition to 1
control on your remote entry transmitter (if
84
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 85
Locks and Security
2. Do not wipe off any grease on the
battery terminals on the back surface of the circuit board.
3. Remove the old battery.
4. Insert the new battery. Refer to the diagram inside the remote entry
transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity.
5. Snap the two halves back together.
Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.
Replacing lost remote entry transmitters
If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming.
How to reprogram your remote entry transmitters
You must have all remote entry transmitters (maximum of four) available before beginning this procedure.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
85
Page 86
Locks and Security
To reprogram the remote entry transmitters:
1. Ensure the vehicle is
electronically unlocked.
2. Put the key in the ignition.
3. Turn the key from the 2 (LOCK)
position to 3 (OFF).
4. Cycle eight times rapidly (within
10 seconds) between the 3 (OFF) position and 4 (ON). Note: The eighth turn must end in the 4 (ON) position.
5. The doors will lock, then unlock, to confirm that the programming
mode has been activated.
6. Within 20 seconds press any button on the remote entry transmitter.
Note: If more than 20 seconds have passed you will need to start the procedure over again.
7. The doors will lock, then unlock, to confirm that this remote entry
transmitter has been programmed.
8. Repeat Step 6 to program each additional remote entry transmitter.
9. Turn the ignition to the 3 (OFF) position after you have finished
programming all of the remote entry transmitters. Note: After 20 seconds, you will automatically exit the programming mode.
10. The doors will lock, then unlock, to confirm that the programming
mode has been exited.
3
2
1
4
5
Illuminated entry
The interior lamps illuminate when the remote entry system is used to unlock the door(s) or liftgate.
The illuminated entry system will turn off the interior lights if:
the ignition switch is turned to the 4 (ON) position, or
the remote transmitter lock control is pressed, or
the 7 8 and the 9 0 controls on the keyless entry keypad are
pressed, or
after 25 seconds of illumination.
The dome lamp control must not be set to the off position for the illuminated entry system to operate.
86
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 87
Locks and Security
The inside lights will not turn off if:
they have been turned on with the dimmer control, or
any door or the liftgate is open.
The battery saver will shut off the interior lamps 30 minutes after the ignition has been turned to the 3 (OFF) position, 10 minutes after if the dome lamp is off, and 30 minutes after if the dome lamp switch is left on.
KEYLESS ENTRY SYSTEM
You can use the keyless entry keypad to:
lock or unlock the doors without using a key.
activate or deactivate the autolock feature.
The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5–digit personal entry code.
When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.
Programming a personal entry code
To create your own personal entry code:
1. Enter the factory set code.
2. Within five seconds press the 1 2 on the keypad.
3. Enter your personal 5-digit code. Each number must be entered
within five seconds of each other.
4. The doors will again lock then unlock to confirm that your personal
keycode has been programmed to the module.
Tips:
Do not set a code that uses five of the same number.
Do not use five numbers in sequential order.
The factory set code will work even if you have set your own personal
code.
If you set a second personal code it will erase your first personal code.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
87
Page 88
Locks and Security
Erasing personal code
1. Enter the factory set 5–digit code.
2. Within five seconds, press the 1 2 on the keypad and release.
3. Press and hold the 1 2 for two seconds. This must be done within
five seconds of completing step 2. Your personal code is now erased and only the factory set 5–digit code
will work.
Anti-scan feature
If an incorrect code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash during this time.
The anti-scan feature will turn off after:
one minute of keypad inactivity.
pressing the
the ignition is turned to the 4 (ON) position.
Unlocking and locking the doors using keyless entry
To unlock the drivers door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. The interior lamps will illuminate after entering a valid keypad entry code.
To unlock all doors, press the 3 4 control within five seconds. To lock all doors, press the 7 8 and the 9 0 at the same time. You
do not need to enter the keypad code first. Note: The interior lamps
will turn off.
Autolock (if equipped)
This feature automatically locks all vehicle doors when the following conditions are met:
the ignition key is in the 4 (ON) position,
all the doors are closed,
the brake is pressed before reaching 8 km/h (5 mph), and
the vehicle is traveling more than 8 km/h (5 mph).
Relock
The autolock feature repeats when the following conditions are met:
the vehicles speed is less than 8 km/h (5 mph),
control on the remote entry transmitter.
88
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 89
Locks and Security
any door is opened then closed while the ignition is in the 4 (ON) position,
the brake is pressed before reaching 8 km/h (5 mph), and
the vehicle is traveling more than 8 km/h (5 mph).
To deactivate/reactivate the autolock feature using the keypad
Your vehicle comes with the autolock feature activated. To deactivate/reactivate this feature:
1. Ensure that the anti-theft system is not armed.
2. Turn the ignition to the 3 (OFF) position.
3. Close all the doors, liftgate and cargo doors.
4. Enter the 5-digit entry code.
5. Press and hold the 7 8. While holding the 7 8, press and release
the 3 4.
6. Release the 7 8.
The horn will chirp once when the system has been successfully deactivated.
The horn will chirp twice (one short and one long chirp) when the system has been successfully reactivated.
To deactivate/reactivate the autolock feature using the power door unlock control
You must complete Steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds.
1. Insert the key and turn the ignition to the 4 (ON) position.
2. Press the power door unlock control three times.
3. Turn the ignition from the 4 (ON) position to the 3 (OFF) position.
4. Press the power door unlock control three times.
5. Turn the ignition back to the 4 (ON) position. The horn will chirp.
6. Press the unlock control, then press the lock control. The horn will
chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. Note: Pressing the power door UNLOCK/LOCK button again will toggle between activating and deactivating the autolock feature.
7. Turn the ignition to the 3 (OFF) position. The horn will chirp once to
confirm the procedure is complete.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
89
Page 90
Locks and Security
SECURILOCKPASSIVE ANTI-THEFT SYSTEM
SecuriLockpassive anti-theft system is an engine immobilization system. This system is designed to prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a no-startcondition.
Your vehicle comes with two coded keys; additional coded keys may be purchased from your dealer. The dealer can program your spare keys to your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key.
Note: The SecuriLockpassive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded key and restart the engine.
Theft indicator
The theft indicator is located in the instrument cluster.
When the ignition is in the 2 (LOCK) position, the indicator will flash once every 2 seconds to indicate the SecuriLocksystem is functioning as a theft deterrent.
When the ignition is in the 4 (ON) position, the indicator will glow for 3 seconds, then turn off to indicate normal system functionality.
If a problem occurs with the SecuriLocksystem, the indicator will flash rapidly or glow steadily when the ignition is in the 4 (ON) position. If this occurs, the vehicle should be taken to an authorized dealer for service.
90
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 91
Locks and Security
Automatic arming
The vehicle is armed immediately after switching the ignition to the 3 (OFF) position.
The
THEFT
every two seconds when the vehicle is armed.
Automatic disarming
Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle.
The
If the
flashes rapidly, have the system serviced by your dealer.
Replacement keys
If your keys are lost or stolen and you dont have an extra coded key, you will need to have your vehicle towed to a dealership. The key codes need to be erased from your vehicle and new coded keys will need to be programmed.
Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.
Programming spare keys
You can program your own coded keys to your vehicle. Please read and understand the entire procedure before you begin.
Tips:
A maximum of eight keys can be coded to your vehicle.
Only use Securilockkeys.
You must have two previously programmed coded keys (keys that
already operate your vehicles engine) and the new unprogrammed key(s) readily accessible.
If two previously programmed coded keys are not available, you must take your vehicle to your dealer to have the spare key(s) programmed.
indicator will flash
THEFT
indicator will illuminate for three seconds and then go out.
THEFT
indicator stays on for an extended period of time or
3
2
1
4
5
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
91
Page 92
Locks and Security
1. Insert a previously programmed
coded key into the ignition.
3
2
1
2. Turn the ignition from the 3 (OFF) position to the 4 (ON) position.
Keep the ignition in the 4 (ON) position for at least one second, but no more than 10 seconds.
3. Turn the ignition to the 3 (OFF) position.
4. Remove the previously programmed coded key from the ignition.
5. Within ten seconds of removing the previously programmed coded key,
insert the other previously programmed coded key into the ignition.
6. Turn the ignition from the 3 (OFF) position to the 4 (ON) position.
Keep the ignition in the 4 (ON) position for at least one second but not more than 10 seconds.
7. Turn the ignition to the 3 (OFF) position.
8. Remove the previously programmed coded key from the ignition.
9. Within twenty seconds of removing the previously programmed coded
key, insert the unprogrammed key (new/valet key) into the ignition.
10. Turn the ignition from the 3 (OFF) position to the 4 (ON) position.
Keep the ignition in the 4 (ON) position for at least one second, but no more than 10 seconds.
11. Your new, unprogrammed key is now programmed.
If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and then go out.
If the key was not successfully programmed, it will not start your vehicles engine and the theft indicator light will flash on and off, or stay on for more than three seconds. If failure repeats, bring your vehicle to your dealer to have the new key(s) programmed.
To program additional new unprogrammed key(s), repeat this procedure from Step 1 for each additional key.
4
5
92
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 93

Seating and Safety Restraints

SEATING
Notes:
Reclining the seatback can cause an occupant to slide under the seats safety belt, resulting in severe personal injuries in the
event of a collision.
Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
40/20/40 seat (if equipped)
Lift the track release bar to move the seat forward or backward. Ensure that the seat is relatched into place.
Seating and Safety Restraints
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
93
Page 94
Seating and Safety Restraints
60/40 split bench seat (if equipped)
Lift the release bar to move the seat forward or backward. Ensure the seat is relatched into place.
Pull the seatback handle up to recline the seat.
Captain’s chair (if equipped)
Lift the track release bar to move the seat forward or rearward. Make sure that the seat is relatched into place.
Pull the seatback handle up to recline the seat.
Push down the lever (if equipped) located at the bottom of the seatback to quickly fold the seatback forward.
94
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 95
Seating and Safety Restraints
Memory seats and adjustable pedals (if equipped)
This system allows automatic positioning of the driver seat and adjustable pedals to two programmable positions.
The memory seat control is located on the driver door.
To program position one, move the driver seat to the desired position using the seat controls. Press the SET control. The SET control indicator light will briefly illuminate. While the light is illuminated, press control 1.
To program position two, repeat the previous procedure using control
2.
A position can only be recalled when the transmission gearshift is in Park or Neutral. A memory seat position may be programmed at any time.
Using the manual lumbar support
For more lumbar support, turn the lumbar support control toward the front of vehicle.
For less lumbar support, turn the lumbar support control toward the rear of vehicle.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
95
Page 96
Seating and Safety Restraints
Adjusting the front power seat (if equipped)
The control is located on the outboard side of the seat cushion.
Press to raise or lower the front portion of the seat cushion.
Press to raise or lower the rear portion of the seat cushion.
Press the control to move the seat forward, backward, up or down.
Heated seats (if equipped)
To operate the heated seats, do the following:
Push control to activate.
Push again to deactivate.
The indicator light on the control will illuminate when activated.
96
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 97
Seating and Safety Restraints
The system will not automatically shutoff unless control is pushed to deactivate. If system is not manually terminated at last use, then system will remain active at next ignition key cycle.
40/20/40 front seat armrest and console (if equipped)
To release the armrest, pull forward on the strap and pull the armrest down. Lift up armrest to return it to a center seatback.
To gain access to the storage compartment in your armrest, lift the latch to open the lid. The lid cannot be opened in the upright position.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
97
Page 98
Seating and Safety Restraints
REAR SEATS
Head restraints
To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Push or pull the head restraint to the desired position.
Rear folding seats (if equipped)
Folding down rear seats into load floor
Ensure that no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down and insure the seat is fully latched rearward.
For assistance, refer to the label located on the seat side shield.
1. Lift strap to release seat cushion.
98
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Page 99
Seating and Safety Restraints
2. Lift seat cushion up and rotate
forward.
3. The headrest must be removed in
order to fold the seatback down. Remove 2nd row seat headrest by pushing in both tabs while pulling up on headrest simultaneously.
4. Stow headrest into the green caps
found on the top of the seat cushion.
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
99
Page 100
Seating and Safety Restraints
5. Lift the lower seat control and
flip the seatback down.
6. For bench seats only, lift up flap
on seatback to release closeout panel.
7. For bench seats only, rotate panel
to closeout the space between the seatback and the floor.
Returning the seat to upright
Ensure the seat is pulled back to the locked position, whether the seat is occupied or empty. If not latched, the seat may cause
injury during a sudden stop.
1. For bench seats, rotate the closeout panel onto the seatback and
secure with the retaining flap.
100
2004 U137 Excursion (hdw) Owners Guide (post-2002-fmt) USA English (fus)
Loading...