Engine compartment272
Engine oil274
Battery277
Fuel information285
Air filter(s)298
Part numbers300
Refill capacities302
Lubricant specifications304
Accessories311
Scheduled Maintenance Guide313
Normal Scheduled Maintenance and Log316
Special Operating Conditions and Log330
Index335
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company. Ford may change the contents without
notice and without incurring obligation.
WARNING: Engine exhaust, some of its constituents, and
certain vehicle components contain or emit chemicals known to
the State of California to cause cancer and birth defects or other
reproductive harm. In addition, certain fluids contained in vehicles and
certain products of component wear contain or emit chemicals known
to the State of California to cause cancer and birth defects or other
reproductive harm.
CONGRATULATIONS
Congratulations on acquiring your new Ford Escape Hybrid. Please take
the time to get well acquainted with your vehicle by reading this
handbook. The more you know and understand about your vehicle, the
greater the safety and pleasure you will derive from driving it.
For more information on Ford Motor Company and its products visit the
following website:
• In the United States: www.ford.com
• In Canada: www.ford.ca
Additional owner information is given in separate publications.
This Owner’s Guide describes every option and model variant available
and therefore some of the items covered may not apply to your
particular vehicle. Furthermore, due to printing cycles it may describe
options before they are generally available.
Remember to pass on this Owner’s Guide when reselling the vehicle. It
is an integral part of the vehicle.
Fuel pump and high voltage battery shut-off switches: In
the event of an accident the fuel pump shut-off switch may
automatically cut off the fuel supply to the engine and the high voltage
shut-off switch cuts off power from the high voltage battery. These
switches can also be activated through sudden vibration (e.g. collision
when parking). For information on resetting the fuel pump shut-off
switch and the high voltage battery shutoff switch, refer to the Fuelpump/high voltage shut-off switches in the Roadside Emergencies
chapter.
How can you reduce the risk of personal injury to yourself or others? In
this guide, answers to such questions are contained in comments
highlighted by the warning triangle symbol. These comments should be
read and observed.
Warning symbols on your vehicle
When you see this symbol, it is
imperative that you consult the
relevant section of this guide before
touching or attempting adjustment
of any kind.
Protecting the environment
We must all play our part in
protecting the environment. Correct
vehicle usage and the authorized
disposal of waste, cleaning and
lubrication materials are significant
steps towards this aim. Information in this respect is highlighted in this
guide with the tree symbol.
BREAKING-IN YOUR VEHICLE
Your vehicle does not need an extensive break-in. Try not to drive
continuously at the same speed for the first 1,000 miles (1,600 km) of
new vehicle operation. Vary your speed frequently in order to give the
moving parts a chance to break in.
Drive your new vehicle at least 500 miles (800 km) before towing a
trailer. For more detailed information about towing a trailer, refer to
Trailer towing in the Tires, Wheels and Loading chapter.
Do not add friction modifier compounds or special break-in oils during
the first few thousand miles (kilometers) of operation, since these
additives may prevent piston ring seating. See Engine oil in the
Maintenance and Specifications chapter for more information on oil
usage.
Your Escape Hybrid has unique qualities which cause it to operate
differently than a typical vehicle.
Starting the vehicle
• The engine will start and run when you first turn the ignition key to
the start position.
• The engine cannot be started in the N (Neutral) position.
• Depending upon temperature and the high voltage battery’s state of
charge, the engine may shut off shortly after starting the vehicle; this
is a normal condition and you do not need to restart the vehicle. The
Ready Indicator Light in the instrument cluster will illuminate to
indicate the vehicle is running. For more Ready Indicator Light
information, refer to Warning lights and chimes in the InstrumentCluster chapter.
DRIVING THE VEHICLE
Starting Out:
Under normal operation with the vehicle at operating temperature, the
engine will start automatically as you accelerate. Sometimes the engine
will start immediately as you begin moving, while other times the vehicle
will obtain a speed of up to 25 mph (40 km/h) before the engine starts.
You may hear and feel the engine starting as you transition from
electrical to hybrid (gas engine on) operation. This is a normal condition.
These are some of the conditions that may cause engine start-up:
• High voltage battery re-charge is required.
• Driver acceleration demands exceed electric motor capability.
• Outside air temperature is overly hot or cold.
• Certain climate system modes of operation.
• If you are starting up hill or accelerating quickly, the engine will start
immediately as operating conditions require additional power.
Note: If the high voltage battery is very cold or very hot, the engine may
operate more than under normal conditions, and vehicle performance
may be temporarily reduced. This is a normal condition.
• Your vehicle does not shift like a conventional vehicle. You may feel
transitions between the various operating modes of the hybrid system,
but no actual shifting occurs. For more information about transmission
operation, refer to Understanding the gearshift positions of the
electronically-controlled Continuously Variable Transaxle (eCVT)
in the Driving chapter.
Stopping the vehicle
• The vehicle’s engine may shut off as you come to a stop; this is a
normal condition and helps to conserve fuel. You do not need to
restart the vehicle.
Neutral operation
• The vehicle does not charge the high voltage battery in the N
(Neutral) position. Do not idle the vehicle in N (Neutral) for extended
periods as this will discharge the high voltage battery.
Low gear operation
• In L (Low) gear, you may feel an increased sensation of engine
braking as you remove your foot from the accelerator. L (Low) gear
can be helpful when driving down an incline; unlike in a conventional
vehicle, L (Low) does not offer an advantage over D (Drive) in uphill
or off-road driving conditions.
Reverse operation
• Vehicle speed is limited to 22 mph (35 km/h) while operating in R
(Reverse) gear.
ESCAPE HYBRID UNIQUE OPERATING CHARACTERISTICS
• You may hear some unique sounds from a hybrid vehicle. The Escape
Hybrid is equipped with a high voltage battery air conditioning system
in the rear of the vehicle which cools the high voltage battery in order
to ensure high voltage battery life and optimize performance. You may
hear a slight clunk or tap noise as the vent door operates, as well as a
fan noise in the rear of the vehicle; this noise is the high voltage
battery cooling fan. The high voltage battery cooling may also continue
to operate for short durations after the vehicle has been turned off.
These vehicle conditions and noises are normal and do not require
service.
• You may hear a pumping sound when you enter the vehicle or a
venting sound a few minutes after parking the vehicle. This is due to
charging and discharging of the hydraulic portion of the regenerative
braking system.
• You may hear a slight whine or whistle when operating your vehicle.
This noise could occur at idle, and during cruising and accelerating; it
is caused by the normal operation of electrical generator in the hybrid
system.
• The Escape Hybrid’s hydraulic brake system used for regenerative
braking is different from other vehicles. The noise from the ABS pump
motor and the brake pedal pulsation are much less than on vehicles
with conventional ABS. Noise and pedal pulsation during ABS may not
be noticed. For more information about braking, refer to Braking in
the Driving chapter.
• The engine speed in an Escape Hybrid is not directly tied to the
vehicle speed. Under certain conditions, the engine speed may appear
much higher than that of a conventional automobile. This is a normal
condition and is caused by engine speed optimization to maximize fuel
economy.
• During certain events (such as vehicle servicing) your low voltage
(underhood) battery may become disconnected or disabled. When this
occurs, and after reconnecting the low voltage (underhood) battery
and driving the vehicle, the engine may continue to operate for 3-5
seconds after the key is turned to the 1 (LOCK) position. This is a
normal condition, as the vehicle’s computers are relearning the
operating characteristics of your particular engine in order to operate
it at maximum efficiency.
• The high voltage battery may go through a self-reconditioning process
from time to time; these events optimize high voltage battery
performance. You may notice slight changes to driveability during the
reconditioning process. This is a normal condition.
• If the vehicle is left inoperative for over 31 days, it may be necessary
to jumpstart the vehicle. For more information, refer to Jumpstarting your vehicle (Low voltage [underhood] battery only) in
the Roadside Emergencies chapter.
Fuel economy can be significantly impacted by your driving habits and
accessory usage. To optimize the fuel economy in your vehicle, please be
aware of the following vehicle functions which affect fuel economy:
A/C operation
• With the climate control system set to MAX A/C, defrost, or
defrost/floor mode (the orange graphics on your climate control), the
engine will typically run continuously, reducing fuel economy. Setting
the climate control system to A/C mode or A/C
reduces fuel economy, but in this case the A/C only operates when the
engine is already running due to other demands. Because the engine
does not run continuously, A/C and A/C
efficient than MAX A/C mode.
Driver habits
• In general, better fuel economy is achieved during moderate
acceleration and deceleration as opposed to aggressive acceleration
and deceleration. This is true regardless of the mode in which you’re
operating your vehicle.
• To maximize fuel economy, try to extend the length of time the
vehicle operates in electric mode by accelerating lightly. The more you
keep the vehicle in electric mode, the better fuel economy you will
achieve.
• For more information on improving the fuel economy of your Escape
Hybrid, refer to Essentials of good fuel economy in the Maintenanceand Specifications chapter.
mode are more fuel
mode also
SPECIAL NOTICES
New Vehicle Limited Warranty
For a detailed description of what is covered and what is not covered by
your vehicle’s New Vehicle Limited Warranty, refer to the WarrantyGuide that is provided to you along with your Owner’s Guide.
Special instructions
For your added safety, your vehicle is fitted with sophisticated electronic
controls.
Please read the section Supplemental restraint system (SRS)
in the Seating and Safety Restraints chapter. Failure to follow
the specific warnings and instructions could result in personal injury.
Front seat mounted rear-facing child or infant seats should
NEVER be placed in front of an active passenger airbag.
Service Data Recording
Service data recorders in your vehicle are capable of collecting and
storing diagnostic information about your vehicle. This potentially
includes information about the performance or status of various systems
and modules in the vehicle, such as engine, throttle, steering or brake
systems. In order to properly diagnose and service your vehicle, Ford
Motor Company, Ford of Canada, and service and repair facilities may
access vehicle diagnostic information through a direct connection to your
vehicle when diagnosing or servicing your vehicle.
Event Data Recording
Other modules in your vehicle — event data recorders — are capable of
collecting and storing data during a crash or near crash event. The
recorded information may assist in the investigation of such an event.
The modules may record information about both the vehicle and the
occupants, potentially including information such as:
• how various systems in your vehicle were operating;
• whether or not the driver and passenger seatbelts were buckled;
• how far (if at all) the driver was depressing the accelerator and/or the
brake pedal;
• how fast the vehicle was traveling; and
• where the driver was positioning the steering wheel.
To access this information, special equipment must be directly connected
to the recording modules. Ford Motor Company and Ford of Canada do
not access event data recorder information without obtaining consent,
unless pursuant to court order or where required by law enforcement,
other government authorities or other third parties acting with lawful
authority. Other parties may seek to access the information
independently of Ford Motor Company and Ford of Canada.
Notice to owners of pickup trucks and utility type vehicles
Utility vehicles have a significantly higher rollover rate than
other types of vehicles.
Before you drive your vehicle, please read this Owner’s Guide carefully.
Your vehicle is not a passenger car. As with other vehicles of this type,
failure to operate this vehicle correctly may result in loss of vehicle
control, vehicle rollover, personal injury or death.
Be sure to read Driving off road in the Driving chapter.
Using your vehicle with a snowplow
Do not use this vehicle for snowplowing.
Your vehicle is not equipped with a snowplowing package.
Using your vehicle as an ambulance
Do not use this vehicle as an ambulance.
Your vehicle is not equipped with the Ford Ambulance Preparation
Package.
Cell phone use
The use of Mobile Communications Equipment has become increasingly
important in the conduct of business and personal affairs. However,
drivers must not compromise their own or others’ safety when using
such equipment. Mobile Communications can enhance personal safety
and security when appropriately used, particularly in emergency
situations. Safety must be paramount when using mobile communications
equipment to avoid negating these benefits.
Mobile Communication Equipment includes, but is not limited to cellular
phones, pagers, portable email devices, in-vehicle communications
systems, telematics devices and portable two-way radios.
A driver’s first responsibility is the safe operation of the vehicle.
The most important thing you can do to prevent a crash is to
avoid distractions and pay attention to the road. Wait until it is safe to
operate Mobile Communications Equipment.
Warning lights and gauges can alert you to a vehicle condition that may
become serious enough to cause expensive repairs. A warning light may
illuminate when a problem exists with one of your vehicle’s functions.
Many lights will illuminate when you start your vehicle to test and make
sure the bulb works. If any light remains on after starting the vehicle,
refer to the respective system warning light for additional information.
Note: A message may be displayed in the message center in conjunction
with an illuminated warning light, refer to Message Center in the DriverControls chapter for more information.
Service engine soon: The Service
engine soon indicator light
illuminates when the ignition is first
turned to the RUN position to check
the bulb. Solid illumination after the engine is started indicates the On
Board Diagnostics System (OBD-II) has detected a malfunction. Refer to
On board diagnostics (OBD-II) in the Maintenance and Specifications
chapter. If the light is blinking, engine misfire is occurring which could
damage your catalytic converter. Drive in a moderate fashion (avoid
heavy acceleration and deceleration) and have your vehicle serviced
immediately by your authorized dealer.
Under engine misfire conditions, excessive exhaust temperatures
could damage the catalytic converter, the fuel system, interior
floor coverings or other vehicle components, possibly causing a fire.
Service soon: The Service soon
indicator illuminates when the
vehicle has detected a malfunction.
Report the fault to a dealer at the
earliest opportunity.
Brake system warning light: To
confirm the brake system warning
light is functional, it will
momentarily illuminate when the
ignition is turned to the RUN
position (when the engine is not running), or in a position between RUN
and START, or by applying the parking brake when the ignition is turned
to the RUN position. If the brake system warning light does not
illuminate at this time, seek service immediately from your authorized
dealer. Illumination after releasing the parking brake indicates low brake
fluid level and the brake system should be inspected immediately by
your authorized dealer.
Driving a vehicle with the brake system warning light on is
dangerous. A significant decrease in braking performance may
occur. It will take you longer to stop the vehicle. Have the vehicle
checked by your authorized dealer.
Anti-lock brake system (ABS): If
the lamp stays on for more than a
few seconds, then an ABS fault is
indicated, have the system serviced
immediately by your authorized
dealer. Normal braking is still functional unless the brake warning light
also is illuminated.
Airbag readiness: If this light fails
to illuminate when ignition is turned
to ON, continues to flash or remains
on, have the system serviced
immediately by your authorized
dealer. A chime will also sound when a malfunction in the supplemental
restraint system has been detected.
Safety belt: Reminds you to fasten
your safety belt. A chime will also
sound to remind you to fasten your
safety belt. If this light continues to
flash the chime will sound again to
remind you to fasten your safety belt.
component fault/failure that will
cause the vehicle to shutdown or
fail to start.
Note: If the vehicle is still running, the vehicle may soon
shutdown without further warning and should be stopped safely.
If this lamp is lit, stop the vehicle, shift to P (Park), turn the key to the
Off position, and attempt to restart the vehicle. If the fault remains, the
vehicle may require refueling, jump starting, resetting of the shut-off
switches, or service. For information regarding Low voltage
[underhood] battery only) and Fuel pump/High voltage shut-off
switches please refer to the Roadside Emergencies chapter.
Charging system: Illuminates when
the 12V charging system is not
working properly.
Ready indicator light: Illuminates
once the vehicle has successfully
started. Indicates the vehicle is
ready to drive even when you don’t
hear the engine running.
Engine oil pressure: Illuminates
when the oil pressure falls below the
normal range, refer to Engine oil in
the Maintenance andSpecifications chapter.
Engine or motor electronic
coolant temperature: Illuminates
when the coolant temperature
exceeds the threshold. When the light is flashing or remains on, stop the
vehicle as soon as possible, switch off the engine and let cool. Refer to
Engine or motor electronic coolant in the Maintenance and
Specifications chapter.
Never remove the coolant reservoir cap while the engine is
running or hot.
Low tire pressure warning:
Illuminates when your tire pressure
is low. If the light remains ON at
start up or while driving, the tire
pressure should be checked. Refer
to Inflating Your Tires in the Tires, Wheels and Loading chapter.
When the ignition is first turned to ON, the light will illuminate for 3
seconds to ensure the bulb is working. If the light does not turn ON,
have the system inspected by your authorized dealer. For more
information on this system, refer to Understanding Your Tire PressureMonitoring System in the Tires, Wheels and Loading chapter.
ABS active/Traction control娂
active (if equipped): Flashes
when the ABS system is active. If
the light remains on, have the
system serviced immediately, refer
to the Driving chapter for more
information.
Anti-theft system: Flashes when
the Securilock娂 Passive Anti-theft
System has been activated.
Turn signal: Illuminates when the
left or right turn signal or the
hazard lights are turned on. If the
indicators stay on or flash faster, check for a burned out bulb.
High beams: Illuminates when the
high beam headlamps are turned on.
Key-in-ignition warning chime: Sounds when the key is left in the
ignition in the OFF/LOCK or ACCESSORY position and the driver’s door
is opened.
Headlamps on warning chime: Sounds when the headlamps or parking
lamps are on, the ignition is off (the key is not in the ignition) and the
driver’s door is opened.
Turn signal chime (if equipped): Sounds when the turn signal lever
has been activated to signal a turn and not turned off after the vehicle is
driven more than 2 miles (3.3 km).
Transmission not in park chime: Sounds when the PRNDL is not in P
(Park) position, the driver’s door is ajar and the ignition is ON.
HEV Engine off Reminder Chime: Sounds for 10 seconds when the
PRNDL is in the P (Park) position and the Driver’s door is ajar (open)
while ignition is ON. Always turn your ignition key to Off and remove key
before leaving your vehicle. (The engine may be off when the vehicle is
stopped, yet the key is on, and the engine can turn on at any time)
Message center activation chime: Sounds when a warning message
appears in the message center display for the first time.
Message center switch activation chime: Sounds when the message
center INFO or SET control is pressed.
Battery gauge: Provides
information about the vehicle’s
energy usage.
• ASSIST — Battery provides extra
power to boost the vehicle’s
acceleration.
• CHARGE — Storing extra energy
in the battery when coasting or
slowing down.
Odometer: Registers the total miles
(or kilometers) of the vehicle.
Trip odometer: Registers the miles
(or kilometers) of individual journeys.
To reset, press and hold the trip reset
button for two or more seconds; this
returns the trip odometer to zero.
Press and release the button to return
to the odometer display.
Tachometer: Indicates the engine
speed in revolutions per minute.
Driving with your tachometer
pointer continuously at the top of
the scale (in the red zone) may
damage the engine. The pointer will
indicate engine RPMs when the
engine is running and point at the
EV symbol when the engine is off and the vehicle is running on pure
electrical power.
Fuel gauge: Indicates
approximately how much fuel is left
in the fuel tank (when the ignition
is in the ON position). The fuel
gauge may vary slightly when the
vehicle is in motion or on a grade.
Satellite Compatible AM/FM Stereo In-Dash Single CD/MP3 Radio
(if equipped)
1. SEEK: Press and release
SEEK
strong station or track.
2. TEXT: The filename (Fi), song
title (So), artist text (Ar) or album
text (AL) may be viewed while
playing an MP3 selection. When MP3 selection text is shown on the
message display, its corresponding text indicator (Fi, So, Ar, or AL) is
shown in the elapsed time display. Press TEXT to scroll through the text
fields. The display will scroll through all of the text in the current field
before changing to the next field. (TEXT must be pressed within 3
seconds of the previous press to proceed to the next/last text display.
The last text field shown on the display will become the new display
message default.
TEXT is also available when equipped with Satellite radio. Your radio
comes equipped with Satellite ready capability. The kit to enable Satellite
reception is available through your dealer. Detailed Satellite instructions
are included with the dealer installed kit. Dealer installed satellite kit
Treble: Press TREB; then press
SEL
the treble output.
7. Select: Use with Bass, Treble,
Balance, Fade and other menu
selections.
8. Balance: Press BAL; then press
SEL
left/right speakers.
Fade: Press FADE; then press
SEL
rear/front speakers.
9. Menu: Press MENU and SEL to
access AUTOSET, Speed sensitive
volume and Setting the clock.
/to decrease/increase
/to decrease/increase
/to shift sound to the
/to shift sound to the
Entertainment Systems
Autoset: Press MENU until AUTOSET appears in the display. Press SEL
to toggle ON/OFF. Allows you to set the strongest local radio stations
without losing your original manually set preset stations for
AM/FM1/FM2. When the six strongest stations are filled, the station
stored in preset 1 will begin playing. If there are less than six strong
stations, the system will store the last one in the remaining presets.
Speed sensitive volume: Press MENU until SPEED VOL X appears in
the display. Then press SEL to increase (
volume setting. The level will appear in the display.
Radio volume changes automatically and slightly with vehicle speed to
compensate for road and wind noise. Recommended level is 1–3. Level 0
turns the feature off and level 7 is the maximum setting.
Setting the clock: Press MENU until SELECT HOUR or SELECT
MINUTE is displayed. Use SEL to manually increase (
) the hours/minutes. Press MENU again to disengage clock mode.
(
Folder/Track mode: In MP3 mode, press MENU until MODE appears in
the display. Use SEL to toggle between FOLDER (only tracks within
selected folder are accessible) or TRACK (all tracks on disc are
accessible) MODE.
10. REPEAT: Press to repeat the
current CD/MP3 track.
11. SHUFFLE: Press to play the
CD/MP3 tracks on the current disc
in random order.
12. FOLDER
the next MP3 directory.
: Press to access
) or decrease ()the
) or decrease
13. FOLDER
the previous MP3 directory.
14. FF(Fast forward): In CD/MP3
mode, press until desired selection
is reached.
15. REW(Rewind): In CD/MP3
mode, press until desired selection
is reached.
16. SAT (if equipped): Your radio
comes equipped with Satellite Ready
capability. The kit to enable the
Satellite reception is available through your dealer. Detailed satellite
instructions are included with the dealer installed kit. Dealer installed
satellite kit only available in the continental United States.
station: Select frequency band; tune
to a station, press and hold a preset
button until sound returns.
19. Power/volume: Press to turn
ON/OFF; turn to increase or
decrease volume levels.
20. CD: Press to enter CD mode.
CD units are designed to play commercially pressed 4.75 in
(12 cm) audio compact discs only. Due to technical
incompatibility, certain recordable and re-recordable compact
discs may not function correctly when used in Ford CD players.
Irregular shaped CDs, CDs with a scratch protection film
attached, and CDs with homemade paper (adhesive) labels should
not be inserted into the CD player. The label may peel and cause
the CD to become jammed. It is recommended that homemade
CDs be identified with permanent felt tip marker rather than
adhesive labels. Ballpoint pens may damage CDs. Please contact
your authorized dealer for further information.
21. COMP(Compression): Brings
soft and loud CD passages together
for a more consistent listening level
when in CD mode. Press COMP to turn the feature ON/OFF.
22. Scan: Press SCAN to hear a
brief sampling of radio stations or
CD/MP3 tracks. Press again to stop.
23. CAT/Tune: Press
manually tune down/up the radio
frequency band.
CAT: CAT is only available when equipped with Satellite Radio. Your
radio comes equipped with Satellite ready capability. The kit to enable
Satellite reception is available through your dealer. Detailed Satellite
instructions are included with the dealer installed kit. Dealer installed
satellite kit only available in the continental United States.
For information regarding SIRIUS Satellite Radio, please call toll-free
888-539-SIRIUS (888-539-7474) or visit the SIRIUS website at
www.siriusradio.com
24. CD slot: Insert a CD with the label side up.
Premium Satellite Compatible AM/FM Stereo In-Dash Six CD/MP3
Radio (if equipped)
Audiophile Satellite Compatible AM/FM Stereo In-Dash Six CD/MP3
Radio (if equipped)
1. SEEK: Press and release
SEEK
strong station or track.
2. TEXT: The filename (Fi), song
title (So), artist text (Ar) or album
text (AL) may be viewed while
playing an MP3 selection. When MP3 selection text is shown on the
message display its corresponding text indicator (Fi, So, Ar, or AL) is
shown in the elapsed time display. Press TEXT to scroll through the text
fields. The display will scroll all of the text in the current field before
changing to the next field. (TEXT must be pressed within 3 seconds of
the previous button press to proceed to the next/last text display.)
TEXT is also available when equipped with Satellite radio. Your radio
comes equipped with Satellite ready capability. The kit to enable Satellite
reception is available through your dealer. Detailed Satellite instructions
are included with the dealer installed kit. Dealer installed satellite kit
and a memory preset to eject a
specific disc. Press and hold to eject
all loaded discs.
6. Bass: Press BASS; then press
SEL
the bass output.
Treble: Press TREB; then press
SEL
the treble output.
7. Select: Use with Bass, Treble,
Balance, Fade and other menu
functions.
8. Balance: Press BAL; then press
SEL
left/right speakers.
Fade: Press FADE; then press
SEL
rear/front speakers.
9. Menu: Press to access the
following features:
RDS (if equipped): Press and hold
MENU to access RDS on/off. Use
SEL to toggle RDS on/off. Press MENU again to access Traffic mode,
Program Type mode or Show Type mode. (MENU must be pressed
within 10 seconds to proceed to the next RDS mode).
The Federal Communications Commission (FCC) and the Canadian Radio
and Telecommunications Commission (CRTC) recommend that FM radio
broadcasters use RDS technology to transmit information. FM radio
stations are independently operated and individually elect to use RDS
technology to transmit station ID and program type as desired.
Traffic: Allows you to hear traffic broadcasts. With the feature ON, press
SEEK or SCAN to find a station broadcasting a traffic report (if it is
broadcasting RDS data). Traffic information is not available in most
U.S. markets.
FIND Program type: Allows you to search RDS-equipped stations for a
certain category of music format: Classic, Country, Info, Jazz, Oldies,
R&B, Religious, Rock, Soft, Top 40.
Press and hold MENU until RDS XX is shown in the display. Press MENU
until FIND appears in the display. Use SEL to scroll through music types.
Press SEEK or SCAN to search for a station playing the requested music
category.
Show TYPE: Displays the station’s call letters or music format.
Press and hold MENU until RDS XX is shown in the display Press MENU
until SHOW appears in the display. Use SEL to select NAME or TYPE.
Occupancy mode: Press MENU until occupancy mode appears in the
display. Press SEL to select ALL SEATS, DRIVER SEAT or REAR SEATS
occupancy mode.
Compression: Brings soft and loud CD passages together for a more
consistent listening level when in CD mode. Press MENU until
compression status is displayed. Press the SEL control to enable the
compression feature when COMPRESS OFF is displayed. Press the SEL
control again to disable the feature when COMPRESS ON is displayed.
Autoset: Allows you to set the strongest local radio stations without
losing your original manually set preset stations for AM/FM1/FM2 . Press
MENU until AUTOSET appears in the display. Press SEL to toggle
ON/OFF. When the six strongest stations are filled, the station stored in
preset 1 will begin playing. If there are less than six strong stations, the
system will store the last one in the remaining presets.
Speed sensitive volume: Radio volume changes automatically and
slightly with vehicle speed to compensate for road and wind noise.
Recommended level is 1–3. Level 0 turns the feature off and level 7 is
the maximum setting.
Press MENU until SPEED VOL X appears in the display. Then press SEL
to increase (
appear in the display.
Setting the clock: Press MENU until SELECT HOUR or SELECT MINS
is displayed. Use SEL to manually increase (
hours/minutes. Press MENU again to disengage clock mode.
) or decrease () the volume setting. The level will
Folder/Track Mode: In MP3 mode, press MENU until MODE appears in
the display. Use SEL to toggle between FOLDER (only tracks within
selected folder are accessible) or TRACK (all tracks on disc are
accessible) MODE.
10. REPEAT: Repeats current
CD/MP3 track when active (ON).
Press to show repeat status. Press
again to toggle status.
11. SHUFFLE: Plays CD/MP3
tracks in random order when active
(ON). Press to show shuffle status.
Press again to toggle status.
12. FOLDER
the next MP3 directory.
: Press to access
13. FOLDER
the previous MP3 directory.
14. FF(Fast forward): In CD mode,
press until desired selection is
reached.
15. REW(Rewind): In CD mode,
press until desired selection is
reached.
16. SAT (if equipped): Your radio
comes equipped with Satellite Ready
capability. The kit to enable the
Satellite reception is available through your dealer. Detailed satellite
instructions are included with the dealer installed kit. Dealer installed
satellite kit only available in the continental United States.
17. BAND: Press to toggle between
AM/FM1/FM2 frequency band.
18. Memory presets: To set a
station: Select frequency band, tune
to a station, press and hold a preset
button until sound returns.
ON/OFF; turn to increase or
decrease volume levels.
20. Load: Press to load a CD. Press
LOAD and a memory preset to load
to a specific disc slot. Press and
hold to load up to six discs.
21. CD: Press to enter CD mode.
CD units are designed to play commercially pressed 4.75 in
(12 cm) audio compact discs only. Due to technical
incompatibility, certain recordable and re-recordable compact
discs may not function correctly when used in Ford CD players.
Irregular shaped CDs, CDs with a scratch protection film
attached, and CDs with homemade paper (adhesive) labels should
not be inserted into the CD player. The label may peel and cause
the CD to become jammed. It is recommended that homemade
CDs be identified with permanent felt tip marker rather than
adhesive labels. Ballpoint pens may damage CDs. Please contact
your authorized dealer for further information.
22. Scan: Press SCAN to hear a
brief sampling of radio stations or
CD/MP3 tracks. Press again to stop.
23. Disc/Tune: Press
manually tune down/up the radio
frequency band, or to listen to the
previous/next CD.
CAT: CAT is only available when equipped with Satellite Radio. Your
radio comes equipped with Satellite ready capability. The kit to enable
Satellite reception is available through your dealer. Detailed Satellite
instructions are included with the dealer installed kit. Dealer installed
satellite kit only available in the continental United States.
For information regarding SIRIUS Satellite Radio, please call toll-free
888-539-SIRIUS (888-539-7474) or visit the SIRIUS website at
www.siriusradio.com
AM/FM stereo in-dash six CD modular audio (if equipped)
1. CD: To begin CD play, press
LOAD. When the system is ready to
accept a disc, IN will appear on the
radio display. You may then insert a CD. The system will load the CD and
begin play after a short pause. The disc number and track number will
illuminate in the display.
If a CD is already loaded into the system, press CD to enter CD mode
and select the desired CD to play.
CD units are designed to play commercially pressed 4.75 in
(12 cm) audio compact discs only. Due to technical
incompatibility, certain recordable and re-recordable compact
discs may not function correctly when used in Ford CD players.
Irregular shaped CDs, CDs with a scratch protection film
attached, and CDs with homemade paper (adhesive) labels should
not be inserted into the CD player. The label may peel and cause
the CD to become jammed. It is recommended that homemade
CDs be identified with permanent felt tip marker rather than
adhesive labels. Ballpoint pens may damage CDs. Please contact
your dealer for further information.