Follett MSC22SC Service Manual

Follett Maestro
Chewblet® 400 Series
Icemaker and Top Kit
for Remcor/Cornelius Countertop ice and beverage dispensers
Order parts online www.follettice.com
Installation, Operation and Service Manual
Following installation, please forward this manual
to the appropriate operations person.
801 Church Lane • Easton, PA 18040, USA Toll free (800) 523-9361 • (610) 252-7301 Fax (610) 250-0696 • www.follettice.com
00117259R04
Table of contents
Welcome to Follett Corporation
Important cautions
Specications
Installation
Operation
Cleaning
Replacement Parts
Models MTC22SC, MSC22SC
Models MTC24SC, MSC24SC
Models MTC30SC, MSC30SC
Model MSC44SC
3
3
4
6
14
14
16
16
17
18
19
Follett Corporation Equipment Return Policy
Follett equipment may be returned for credit under the following conditions:
1. The equipment is new and unused.
2. A return authorization number has been issued by customer service within 30 days after shipment.
3. Follett receives the equipment at the factory in Easton, PA within 30 days after issuance of the return authorization number.
4. The equipment must be returned in Follett packaging. If the packaging has been damaged or discarded, Follett will forward, at the customer’s expense, new packaging.
Note: Return freight charges are the responsibility of the customer. If equipment is returned and is damaged because of improper packaging,
Follett Corporation will not be held responsible.
Credit will be issued when: The equipment has been inspected by Follett and deemed suitable to be returned to stock.
Note: A 15% restocking charge will be deducted from the credit. If the cost to return the product to stock exceeds 15%, the actual cost will be deducted.
2
Welcome to Follett
MSC22SC
Icemaker configuration SC = self-contained
Dispenser size 22 = 22" wide 24 = 24" wide 30 = 30" wide 44 = 44" wide
Dispenser manufacturer C = Cornelius L = Lancer S = SerVend
Icemaker mounting MT = Maestro top mount MS = Maestro Satellite-fill
!
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale support. To ensure that this equipment delivers that same degree of service, we ask that you review the installation portion of this manual before beginning to install the unit. Our installation instructions are designed to help you achieve a trouble-free installation. Should you have any questions or require technical help at any point, please call our technical service group at (800) 523-9361 or (610) 252-7301.
Before you begin
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the ling of a claim, if necessary.
Check your paperwork to determine which model you have. Follett model numbers are designed to provide information about the type and capacity of Follett equipment. Following is an explanation of the different model numbers in the series.
Important cautions
Dispenser bin area contains mechanical, moving parts. Keep hands and arms clear of this area at all times. If access to this area is required, power to unit must be disconnected rst.
Follett recommends a Follett water lter system (part# 00130229 for the 400 series) be installed in the icemaker inlet water line.
Ice is slippery. Maintain counters and oors around dispenser in a clean and ice-free condition.
Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.
3
Specications
Electrical
Model number Full load amps Max. fuse size
MC400 series icemaker 115/60/1 11.0 amps 20 amps
Ambient specications
Air temperature +100 F/+38 C max. +50 F/+10 C min. (best performance below +80 F/+27 C)
Water temperature +90 F/+32 C max. +40 F/+4 C min. (best performance below +70 F/+21 C)
Water pressure 70 P.S.I. max.(482kPA) 10 P.S.I min. (89kPA)
Plumbing
Your new icemaker is equipped with a drain line to simplify draining the evaporator and oat reservoir. The tube labeled “oat/evap drain” is for SERVICE USE ONLY and must NOT be connected to the icemaker drain.
Water line sizes Make up water (inlet to oat) 1/4" min.
Condenser (water-cooled only) 3/8" min.
Drain line sizes Icemaker drain 3/4" min.
Condenser (water-cooled only) 3/8" min.
Slope to drain 1/4" per foot (6mm per 30.4cm run) 1/2" min.
Water shut-off recommended within 10 feet (3m), drain to be hard-piped and insulated
Separate drains for icemaker and condenser. To prevent back ow, do NOT connect drains.
Follett recommends installation of a Follett water lter system (part# 00130229) in icemaker inlet water line
Field Wiring: countertop dispensers with Satellite-ll icemakers
Consult enclosed D400A/W, R400A/W, MCD400A/W manual.
4
20.75" (527mm)
22.75" (578mm)
13.00"
(331mm)
4.875"
(124mm)
2.375"
(61mm)
1.875" (48mm)
7.00" (178mm)
A
A
B
B
F
F
D
E
C
A
B
C
C
17.00"
(432mm)
Front view — air-cooled
Satellite-fill
Side view — air-cooled and water-cooled
top mount and Satellite-fill
Satellite-fill air-cooled units only
Back view — air-cooled
top mount
Front view — water-cooled
Satellite-fill
Back view — water-cooled
top mount
12.875"
(327mm)
4.75"
(121mm)
8.375"
(213mm)
2.25"
(57mm)
1.875" (48mm)
Front view — air-cooled
top mount
Icemaker plug
configuration
NEMA 5-20
6.875"
(175mm)
2"
(51mm)
Dimensions and clearances
Required clearances – MCD400 series
Entire front of icemaker clear of obstruction/connections to allow removal.
12" (305mm) above icemaker for service
6" (153mm) minimum between louvered (exhaust) side of icemaker and any adjacent equipment.
MCD400AHS – 18" (457mm) minimum, 10 ft (3m) maximum between discharge and air intake grilles.
A – 3/4" MPT drain B – 3/8" OD push-in water inlet C – Electrical cord
D – 3/8" FPT condenser inlet E – 3/8" FPT condenser drain F – Bin signal cord
5
Installation
ON
OFF
agitation
timer
storage hopper
gate
restrictor
plate
flange extends
into storage
hopper through
gate opening
apply RTV to this surface to seal to
hopper gate
mounting plate
gasket
flat washer
10-32 nut
ice chute
ice diverter
(supplied)
gate
mounting
plate
1. Install Cornelius ice dispenser according to manufacturer’s specications.
Note: We recommend that the dispenser back
be mounted at least 1" (26mm) from wall to allow water, drain and electric lines from top-mount icemakers to be concealed behind dispenser.
2. Disconnect power to dispenser.
3. Remove front panel/merchandiser from the dispenser.
4. Adjust the agitation timer located on Cornelius PC board to 1 second on – 1 hour off (Fig. 1).
Fig. 1
5. Install supplied nugget ice diverter at dispenser opening.
a) Disassemble
chute assembly and discard gate restrictor (Fig. 2.1).
b) Reassemble with
supplied ice diverter as shown (Fig. 2.2).
6. Reinstall front panel.
Fig. 2
1
2
6
Loading...
+ 14 hidden pages