Fluke 8846A, 8845A User manual

Download

8845A/8846A

Digital Multimeter

Programmers Manual

September 2006, Rev. 2, 6/08

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Each Fluke product is warranted to be free from defects in material and workmanship under normal use and service. The warranty period is one year and begins on the date of shipment. Parts, product repairs, and services are warranted for 90 days. This warranty extends only to the original buyer or end-user customer of a Fluke authorized reseller, and does not apply to fuses, disposable batteries, or to any product which, in Fluke's opinion, has been misused, altered, neglected, contaminated, or damaged by accident or abnormal conditions of operation or handling. Fluke warrants that software will operate substantially in accordance with its functional specifications for 90 days and that it has been properly recorded on non-defective media. Fluke does not warrant that software will be error free or operate without interruption.

Fluke authorized resellers shall extend this warranty on new and unused products to end-user customers only but have no authority to extend a greater or different warranty on behalf of Fluke. Warranty support is available only if product is purchased through a Fluke authorized sales outlet or Buyer has paid the applicable international price. Fluke reserves the right to invoice Buyer for importation costs of repair/replacement parts when product purchased in one country is submitted for repair in another country.

Fluke's warranty obligation is limited, at Fluke's option, to refund of the purchase price, free of charge repair, or replacement of a defective product which is returned to a Fluke authorized service center within the warranty period.

To obtain warranty service, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that service center, with a description of the difficulty, postage and insurance prepaid (FOB Destination). Fluke assumes no risk for damage in transit. Following warranty repair, the product will be returned to Buyer, transportation prepaid (FOB Destination). If Fluke determines that failure was caused by neglect, misuse, contamination, alteration, accident, or abnormal condition of operation or handling, including overvoltage failures caused by use outside the product’s specified rating, or normal wear and tear of mechanical components, Fluke will provide an estimate of repair costs and obtain authorization before commencing the work. Following repair, the product will be returned to the Buyer transportation prepaid and the Buyer will be billed for the repair and return transportation charges (FOB Shipping Point).

THIS WARRANTY IS BUYER'S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY.

Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation of incidental or consequential damages, the limitations and exclusions of this warranty may not apply to every buyer. If any provision of this Warranty is held invalid or unenforceable by a court or other decision-maker of competent jurisdiction, such holding will not affect the validity or enforceability of any other provision.

Fluke Corporation P.O. Box 9090 Everett, WA 98206-9090 U.S.A.

Fluke Europe B.V. P.O. Box 1186 5602 BD Eindhoven The Netherlands

11/99

To register your product online, visit http://register.fluke.com

Title Page

Introduction........................................................................................................ 1

Safety Information ............................................................................................. 1

Symbols ......................................................................................................... 2

Local and Remote Operation......................................................................... 2

Computer Interfaces ...................................................................................... 3

Optimizing System Speed for I/O Operation..................................................... 3

Selecting the Remote Interface Port .................................................................. 4

Configuring the IEEE-488 Port ......................................................................... 4

IEEE-488 Operating Limitations................................................................... 4

Setting the IEEE-488 (GPIB) Port Address .................................................. 4

Capability Commands ................................................................................... 5

Interconnections ............................................................................................ 5

Configuring the RS-232 Port ............................................................................. 6

Setting RS-232 Baud Rate............................................................................. 6

Setting RS-232 Parity and Data Bits ............................................................. 7

Setting RS-232 Stop Bits............................................................................... 7

Setting RS-232 Flow Control ........................................................................ 7

Setting RS-232 End-Of-Line Character ........................................................ 7

Enabling and Disabling Fluke 45 Emulation Echo........................................ 7

RS-232 Modes of Operation.......................................................................... 8

Operating with FlukeView Forms’................................................................ 10

Interconnections ............................................................................................ 10

Configuring the Ethernet (LAN) Port ................................................................ 12

Setting the IP Address ................................................................................... 13

Setting the LAN Subnet Mask....................................................................... 14

Reading the Domain Name ........................................................................... 14

Configuring the Host Name........................................................................... 14

Reading the MAC Address............................................................................ 15

Configuring the LAN Default Gateway ........................................................ 15

Configuring the General Network Socket Port.............................................. 15

Establishing an Ethernet Connection................................................................. 16

Terminating an Ethernet Connection................................................................. 17

Selecting the Programming Language ............................................................... 17

Getting Started With an Installation Test........................................................... 17

Installation Test for RS-232 Connections ..................................................... 17

8845A/8846A

Programmers Manual

Installation Test for IEEE-488 Connections.................................................. 18

If The Test Fails............................................................................................. 18

How the Meter Processes Input ......................................................................... 19

Input Strings .................................................................................................. 19

Input Terminators .......................................................................................... 19

Typical IEEE-488 Input Strings .................................................................... 20

Sending Numeric Values to the Meter .......................................................... 20

Sending Command Strings to the Meter........................................................ 20

How the Meter Processes Output....................................................................... 22

Triggering Input................................................................................................. 22

Internal Triggering......................................................................................... 22

External Triggering ....................................................................................... 23

Service Requests (IEEE-488 Only) and Status Registers .................................. 23

Standard Event Status and Standard Event Status Enable Registers............. 24

Questionable Data Event Register and Questionable Data Enable Register . 25

Status Byte Register ...................................................................................... 26

Reading the Status Byte Register .................................................................. 26

Service Request Enable Register................................................................... 27

Supported SCPI Commands .............................................................................. 28

SCPI Command Summary ............................................................................ 28

SCPI Command Details................................................................................. 37

Using the MEASure? Command ................................................................... 38

Using the CONFigure Command .................................................................. 39

Using the READ? Command ........................................................................ 42

Using the INITiate Command ....................................................................... 42

Using the FETCh? Command ....................................................................... 42

Using the SENSe Subsystem to Configure the Meter ................................... 43

Programming for Math Operations................................................................ 51

Programming the Trigger System.................................................................. 55

Using System-Related Commands ................................................................ 58

Using Status Reporting Commands............................................................... 61

Calibration Commands.................................................................................. 63

Using RS-232/Ethernet Interface Commands ............................................... 65

Command Terminators.................................................................................. 66

Alternate Programming Language Compatibility ......................................... 67

FLUKE 45 Command Emulation Summary...................................................... 68

Computer Interface Command Set ................................................................ 68

IEEE-488 Capabilities and Common Commands ......................................... 68

Triggering Output.......................................................................................... 75

Using FlukeView Forms.................................................................................... 76

FLUKE 8842A Emulation Mode....................................................................... 77

Example Notes............................................................................................... 77

Device-Dependent Command Set ................................................................. 79

Input Syntax................................................................................................... 87

Output Data ................................................................................................... 89

Service Requests............................................................................................ 91

Introduction........................................................................................................ 94

Introduction........................................................................................................ 103

Incompatible Fluke 45 Commands .................................................................... 103

Dual Functions............................................................................................... 103

Reading Rates................................................................................................ 104

Ranges ........................................................................................................... 104

Introduction........................................................................................................ 105

Your Meter and Your Network Administrator .................................................. 105

Network Primer.................................................................................................. 106

Contents (continued)

Physical Layer Wiring Schemes Supported by the Meter ............................. 106

Network Interconnection Devices ................................................................. 107

Basic Network Packet and Frame Contents .................................................. 107

IP Addresses and Segmented Networks ........................................................ 108

TCP/IP Protocol Stack................................................................................... 110

Introduction........................................................................................................ 113

Device Dependent Command Set ...................................................................... 113

Calibration Commands ...................................................................................... 113

Dn (Display Commands) ................................................................................... 114

Gn (Get Commands).......................................................................................... 114

Tn (Trigger Mode Commands).......................................................................... 114

Wn (Terminator Commands)............................................................................. 114

Numeric Entry Command.................................................................................. 114

Talk-Only Mode ................................................................................................ 114

Ranging in 8842A Emulation Mode.................................................................. 114

Operational Differences..................................................................................... 115

Appendices

A Error Codes ................................................................................................ 95

B Fluke 45 Emulation Limitations.................................................................. 103

C Network Consideration................................................................................ 105

D Fluke 8842A Emulation Limitations........................................................... 113

iii

8845A/8846A

Programmers Manual

List of Tables

Table Title Page

1. Safety and Electrical Symbols................................................................................ 2

2. IEEE-488 Compatibility Codes.............................................................................. 5

3. Factory Settings of RS-232 Communications Parameters ..................................... 6

4. Status Register Summary ....................................................................................... 23

5. Description of Bits in ESR and ESE ...................................................................... 25

6. Description of Bits in the Questionable Data Register........................................... 26

7. Description of Bits in the Status Byte Register...................................................... 27

8. CALibration command summary........................................................................... 28

9. CONFigure command summary ............................................................................ 29

10. IEEE-488.2 common command summary ............................................................. 29

11. Math command summary....................................................................................... 30

12. MEASure command summary ............................................................................... 30

13. Measurement configuration command summary ................................................... 31

14. RS-232 interface command summary .................................................................... 34

15. Status reporting command summary...................................................................... 35

16. System-Related command summary...................................................................... 36

17. Triggering command summary .............................................................................. 37

18. Preset Conditions for the MEASure? and CONFigure Commands ....................... 41

19. Allowed math/measurement function combinations.............................................. 51

20. IEEE-488.2 Common Commands.......................................................................... 68

21. Fluke 45 Function Commands and Queries ........................................................... 70

22. Function Modifier Commands and Queries ........................................................... 71

23. Range and Measurement Rate Commands and Querie .......................................... 72

24. Measurement Queries............................................................................................. 73

25. Compare Commands and Queries.......................................................................... 74

26. Trigger Configuration Commands ......................................................................... 74

27. Miscellaneous Commands and Queries ................................................................. 75

28. RS-232 Remote/Local Configuration Commands ................................................. 75

29. Trigger Types......................................................................................................... 76

30. 8842A Get Commands........................................................................................... 81

31. Serial Poll Register................................................................................................. 92

32. Serial Poll Register Description ............................................................................. 93

33. Execution Error Codes and Descriptions ............................................................... 94

34. Ethernet/ IEEE-488 Configuration Errors.............................................................. 99

35. Calibration Errors................................................................................................... 99

8845A/8846A

Programmers Manual

36. Non-compatible Fluke 45 Remote Commands ...................................................... 103

37. Fluke 45 Dual Function Compatibility Matrix....................................................... 104

38. IP Address Assignments ........................................................................................ 108

39. 8842A Device Dependent Commands Not Supported........................................... 113

40. Fluke 8845A/8846A Commands the Fluke 8842A Doesn't Support ..................... 113

41. 8842A Virtual Range Mapping.............................................................................. 115

List of Figures

Figure Title Page

1. RS-232 Pin-out and Cable Interconnect................................................................. 12

2. Typical IEEE-488 Input String .............................................................................. 21

3. Overview of Status Data Structure (8845A/8846A and Fluke 45)......................... 24

4. 884XA Triggering System ..................................................................................... 56

7. 8842A Emulation Data Output Format .................................................................. 80

vii

8845A/8846A

Programmers Manual

viii

Introduction

Remote operation of the 8845A or 8846A Digital Multimeter (hereafter “the Meter”) from a host, that is, a terminal, controller, PC, or computer, is accomplished by sending commands to it through one of its remote interfaces. This manual describes how to setup, configure, and operate the Meter through each of the remote interfaces.

Remote Operation

The Meter is controlled remotely using either Standard Commands for Programmable Instruments (SCPI), Fluke 45 or Fluke 8842A (8840A and 8842A) commands. Detailed information on the SCPI command set, and how the Meter processes those commands is included in this manual. Fluke 45 command limitations are covered in Appendix B and Fluke 8842A command limitations are covered in Appendix D in this manual.

Note

For more information regarding the SCPI programming language, visit

http://www.scpiconsortium.org

found at http://www.scpiconsortium.org/SCPI-99.pdf.

The level of detail in this chapter is based on the assumption that the reader is familiar with the basics of data communication interface, and the IEEE-488 bus.

. A free copy of the SCPI standard can be

Safety Information

This section addresses safety considerations and describes symbols that may appear on the Meter or in the manual.

A XW Warning statement identifies conditions or practices that could result in injury or death.

8845A/8846A

Programmers Manual

A W Caution statement identifies conditions or practices that could result in damage to the Meter or equipment to which it is connected.

Symbols

Table 1 is a list of safety and electrical symbols that appear on the Meter or in this manual.

Symbol Description Symbol Description

XW Warning

To avoid electric shock, personal injury, or death, carefully read the information under “Safety Information” before attempting to install, use, or service the Meter.

Table 1. Safety and Electrical Symbols

B F D

C R

Risk of danger. Important information. See manual

Hazardous voltage. Voltage > 30 V dc or ac peak might be present

AC (Alternating Current)

DC (Direct Current)

AC or DC (Alternating or Direct Current)

Continuity test or continuity beeper tone

Potentially hazardous voltage

Double insulated

Static awareness. Static discharge can damage part(s)

CAT II

Display ON / OFF

Earth ground

Capacitance

Diode

Fuse

Digital signal

Maintenance or Service

IEC 61010 Overvoltage (installation or measurement) Category 2.

Recycle

Do not dispose of this product as unsorted municipal waste. Go to Fluke’s website for recycle information.

Local and Remote Operation

When the Meter is operated from a host, it is said to be operated remotely. When operated from the front panel, it is said to be operated locally.

Most operations that can be performed locally can also be performed remotely over the remote interface. Some operations, like setting communications parameters for the RS-232 interface, and addressing the Meter for IEEE-488 operations can only be set through the front panel.

XW Warning

To avoid electric shock, turn off the signal source to the Meter before touching the test leads. The front panel display may not indicate the true input voltage while in remote mode. Always assume lethal voltages exist on the front-panel inputs.

Digital Multimeter

Computer Interfaces

Both the 8845A and 8846A Multimeters come equipped with an RS-232, Ethernet, and IEEE-488 interface. Only one remote interface can be enabled at a time. Using any of the interfaces turns the Meter into a fully programmable instrument that can be integrated into an automated instrumentation system. For a PC with only USB ports, Fluke makes a cable (Fluke PN 2675479) that converts between USB and RS-232 ports.

Note

The remote interface port and settings can be changed only through the Meter’s front-panel controls.

Enabling or selecting a port for remote operation is a separate process from setting the various parameters associated with a remote interface. An interface does not have to be selected to set its parameters; for example, the baud rate of the RS-232 port can be set while the Meter has the LAN port enabled as the remote control port.

Optimizing System Speed for I/O Operation

Several factors affect the remote system speed of the 8845A/46A. To make the fastest measurements, it is best to store the measurements in internal memory before transferring across the I/O bus. This is particularly true if you want to collect a large number of samples per measurement. Set up all of the parameters (i.e. function, range, filters, etc...) prior to taking the measurements. Use the internal trigger. Set the trigger delay to zero. Turn off the display. If operating with RS-232, use the fastest baud rate available.

One example of taking fast voltage readings is:

*cls # This clears all error prior to initiating readings

conf:volt:dc 0.1 # Set the DC range to manual and 100 mV.

volt:dc:nplc 0.02 # Set the NPLC to faster reading rate 4 1/2 digits.

zero:auto 0 # Turn Autozero off.

trig:sour imm # Set immediate trigger.

trig:del 0 # Set trigger delay to zero.

trig:coun 1 # Set trigger count to one or specify a larger number.

disp off # Turn display off. This may slightly improve reading rate.

syst:rem # Put the 8846A in remote. Only needed for RS-232 or Ethernet #(required for READ? or MEAS?)

samp:coun 100 # Set the sample count from 1 to 5000.

:INIT; *OPC? # "*OPC?" returns 1 indicating that the measurements have been

taken and are ready to be transferred to the computer using the FETCH? command.

:FETCH?

Note

For any sample count greater than 1, measurements are returned comma separated.

8845A/8846A

Programmers Manual

Selecting the Remote Interface Port

To enable or select a port for remote control of the Meter:

1. Press I.

2. Press PORT IF.

3. Press SELECT PORT.

4. Press the soft key labeled with the desired port: RS 232C, IEEE488, or LAN.

Port selection is non-volatile. Therefore, the selected port will remain active until another port is selected through the front panel.

Configuring the IEEE-488 Port

The IEEE-488 interface is designed in compliance with supplemental standard IEEE-

488.2. Devices connected to the bus in a system are designated as talkers, listeners, talker/listeners, or controllers. The connector for connecting the Meter to the IEEE-488 bus is located on the rear panel. Under control of an instrument controller, the Meter operates exclusively as a talker/listener on the IEEE-488 bus.

The Meter conforms to the Standard Specification IEEE-488.1 – 1987: IEEE Standard

Digital Interface for Programmable Instrumentation, and to IEEE-488.2 - 2004: Codes, Formats, Protocols, and Common Commands.

IEEE-488 Operating Limitations

The following limitations govern the IEEE-488 remote interface:

• A maximum of 15 instruments may be connected in a single IEEE-488 bus system.

• The maximum length of IEEE-488 cable used on a single IEEE-488 system must be the

lesser of 20 meters, or 2 meters times the number of devices in the system.

Setting the IEEE-488 (GPIB) Port Address

Before the Meter will accept commands through the IEEE-488 remote interface, IEEE488 must first be enabled or selected as the active interface port. This can only be done through the Meter’s front panel.

A controller uses an address between 1 and 32 to identify a specific instrument on the bus. The Meter is shipped from the factory with the IEEE-488 port address set to 1. To change the IEEE-488 address:

1. Press I.

2. Press PORT IF.

3. Press IEEE488.

4. Use the soft keys to set the address as follows.

Select the address digit to adjust by pressing either <-- or -->.

With the desired digit selected, press the soft key labeled -- to decrement the digit or ++ to increment the digit.

5. With the desired address set, press ENTER.

Digital Multimeter

Configuring the IEEE-488 Port

Capability Commands

To conform to the IEEE-488.1 standard specification, it is not essential for a device to encompass the full range of bus capabilities. The IEEE-488.1 document describes and codes the standard bus features, so that manufacturers may give brief coded descriptions of their own interfaces’ overall capability.

The codes that apply to the Meter are given in Table 1 below, together with short descriptions. These codes conform to IEEE-488.2 requirements.

Appendix C of the IEEE-488.1 document contains a complete description of each code.

Table 2. IEEE-488 Compatibility Codes

IEEE-488 Subset Interface Functions

SH1 Source Handshake Capability

AH1 Acceptor Handshake Capability

T5 Talker (basic talker, serial poll, unaddressed to talk if addressed to listen)

L4 Listener (basic listener, unaddressed to listen if addressed to talk)

SR1 Service Request Capability

RL1 Remote/Local Capability (includes local lockout)

PP0 No Parallel Poll Capability

DC1 Device Clear Capability

DT1 Device Trigger – Supports group trigger (GET).

C0 No Controller Capability

E2 Open-Collector and Three-State Drivers

Interconnections

Instruments fitted with an IEEE-488 interface communicate with each other through a standard set of interconnecting cables, as specified in the IEEE-488.1 Standard document.

The IEEE-488 interface connector is located on the Meter’s rear panel.

8845A/8846A

Programmers Manual

Configuring the RS-232 Port

The RS-232 Communication Interface allows ASCII, asynchronous, serial communication between the Meter and a host or terminal. The following sections describe the process of configuring the RS-232 port. To make the RS-232 port the active port for remote operation, see the “Selecting the Remote Interface Port” section above.

Table 3 lists the RS-232 parameter settings when the Meter leaves the factory.

To access the RS-232 setup menu:

Table 3. Factory Settings of RS-232 Communications Parameters

Parameter Factory Setting

Baud Rate 9600

Parity None (Parity bit 0)

Number of Data Bits 8 (7 data bits plus 1 parity bit)

Number of Stop Bits 1

Flow Control None

1. Press I.

2. Press the PORT IF soft key.

3. Press the RS 232C soft key.

At this point, all the RS-232 settings are made available.

All RS-232 port parameter settings are non-volatile and remain set until changed.

Setting RS-232 Baud Rate

To set the baud rate:

1. With the RS-232 set up menu displayed, press BAUD RATE.

There are eight pre-defined settings: 1200, 2400, 4800, 9600, 19200 38400, 57600, 115200, and 230400. These selections are displayed in two separate menus. When first entering baud rate selection, baud rates 9600 to 1200 are displayed. To get to the next five higher baud rates, press MORE. To get back to the lower baud rates, press B.

2. With the desired baud rate displayed, press the soft key under the chosen baud rate.

Note

Digital Multimeter

Configuring the RS-232 Port

Setting RS-232 Parity and Data Bits

To set the data bits:

1. With the RS-232 set up menu displayed, press PARITY DATA BIT.

2. Press the soft key under the desired parity, and data bit parameter.

NONE 8B DATA = No parity with 8 data bits ODD 7B DATA = Odd parity with 7 data bits EVEN 7B DATA = Even parity with 7 data bits

Setting RS-232 Stop Bits

To set the stop bits:

1. With the RS-232 set up menu displayed, press PARITY DATA BIT.

2. Press the soft key labeled 2 STOP BITS to toggle between 1 and 2 stop bits.

Note

When 2 STOP BITS is highlighted, the interface is configured to use 2 stop bits.

Setting RS-232 Flow Control

To set flow control:

1. With the RS-232 set up menu displayed, press FLOW CONTROL.

2. Press the soft key under the desired flow control.

NONE = No flow control XON = Software flow control Xon (hex 11) and Xoff (hex 13) RTS = Hardware flow control, RTS/CTS

Setting RS-232 End-Of-Line Character

To set the End-Of-Line (EOL) character:

1. With the RS-232 set up menu displayed, press EOL.

2. Press the soft key labeled with the desired End-Of-Line character(s).

CR = Carriage return only LF = Line Feed only CR LF = Carriage Return and Line Feed

Setting the EOL character(s) in RS-232 also sets the same EOL character(s) for Ethernet operation.

Note

Enabling and Disabling Fluke 45 Emulation Echo

Although you can turn echo on or off at anytime, the selection is only used or changed when the Meter’s command mode is set to Fluke 45 emulation.

To enable or disable Echo for the RS-232 port:

1. With the RS-232 set up menu displayed, press COMP/TERM ECHO.

2. Press either the ECHO or NO ECHO soft key.

8845A/8846A

Programmers Manual

RS-232 Modes of Operation

RS-232 communication is slightly different between the 8845A/46A and the Fluke 45 emulation modes. Switching between these two command languages is covered in the “Selecting the Programming Language” section later in this manual. The following sections explain the differences in communications protocol and how to set the Meter and computer parameters for proper operation.

8845A/8846A Mode

There are two modes of RS-232 operation when the Meter has the 8845A or 8846A command set selected: TERMINAL and COMPUTER. The terminal mode is an interactive mode where an operator inputs commands, with immediate returns for requested information (queries) and interface messages. In terminal mode, characters sent to the Meter are echoed on the host’s display screen and a command prompt (for example 3>) is returned after the CR/LF is entered by the terminal. If you send a character to the Meter over the RS-232 interface, pressing the <DELETE> or <BACKSPACE> key deletes the previous character. A backspace is echoed to the host terminal.

Note

^C (CNTRL C) is the RS-232 equivalent of IEEE-488 DCI (device clear), causing “1>” followed by a carriage return and line feed to be output.

The computer mode is used when the Meter is operated by computer program. In this mode, requested information is returned by query, and interface messages are queued and returned by command. Characters are not echoed on the host computer and command prompts are suppressed. The <DELETE> or <BACKSPACE> keys are ignored.

Selecting Between Computer and Terminal Mode

Although you can select between Computer and Terminal mode at any time, the selection is only used or changed when the Meter’s command mode is set to 8845A/46A.

To select computer or terminal mode from the front panel:

1. Press I and then PORT IF.

Note

If the RS-232 port is not already highlighted, press SELECT PORT and then RS 232C.

2. Press either RS 232C, COMP/TERM ECHO and select either COMPUTER or

TERMINAL.

Fluke 45 Mode

In the Fluke 45 Command emulation mode, there are two modes of RS-232 operation: ECHO or NO ECHO. In Echo mode, characters sent to the Meter are echoed on the host’s display screen. In No Echo mode, characters sent are not echoed.

To set the echo parameter, refer to the "Enabling and Disabling RS-232 Echo" section earlier in this manual. If you send a character to the Meter over the RS-232 interface, pressing the <DELETE> or <BACKSPACE> key deletes the previous character. A backspace is echoed to the display screen if Echo On mode is set.

In either mode, when the host sends a command to the Meter over the RS-232 interface, the Meter parses and executes the command, and returns a response if appropriate, and sends one of three prompts:

Digital Multimeter

Configuring the RS-232 Port

=> No errors were detected and the command was successfully parsed and

executed.

?> A Command Error was detected. The command was not executed because it

was not understood. For instance, this prompt would be returned if the Meter was sent an input string that contained a syntax error.

!> An Execution Error was detected. The command was understood but not

executed (i.e., a device-dependent error). For instance, this prompt would be returned if you attempted to use the decibels modifier (dB) on a frequency measurement (FREQ).

Note

^C (CNTRL C) is the RS-232 equivalent of IEEE-488 DCI (device clear), causing "=>" followed by a carriage return and line feed to be output.

Terminations for the end of line can be set to carriage return (CR), line feed (LF), or both (CRLF). Terminations for the end of line can be set in the <Instr SETUP><PORT IF><RS232C> selection.

To change the Meter to Fluke 45 Emulation Mode, setup the remote interface for RS-232 or IEEE-488 (Fluke 45 mode will not work over Ethernet):

For RS-232

1. Press I

2. Press PORT IF softkey.

3. Press the SELECT PORT softkey.

4. Press the RS 232C softkey.

Set the baud rate to 9600 as follows:

1. Press I

2. Press PORT IF softkey.

3. Press the RS 232C softkey.

4. Press the BAUD RATE softkey.

5. Press the 9600 softkey.

Set the RS-232 port to non-echo as follows:

1. Press I

2. Press PORT IF softkey.

3. Press the RS 232C softkey.

4. Press the COMP/TERM ECHO softkey.

5. Press the NO ECHO softkey.

For IEEE-488

1. Press I

2. Press PORT IF softkey.

3. Press the SELECT PORT softkey.

4. Press the IEEE488 softkey.

Set the IEEE-488 address to a system compatible value as follows:

8845A/8846A

Programmers Manual

1. Press I

2. Press PORT IF softkey.

3. Press the IEEE488 softkey.

4. Use the soft keys to set the address as follows.

5. With the desired address set, press ENTER.

To set the Meter to Fluke 45 emulation:

1. Press I

2. Press the COMMANDS softkey.

3. Press the FLUKE 45 softkey.

Operating with FlukeView Forms’

When first powered up, FlukeView Forms sends remote commands to the serial port asking an instrument to identify itself. Because the Meter does not recognize the commands for the other instruments, an error indication (Syntax error [-102]) is shown on the Meter’s front panel. This cannot be avoided and is considered normal operation. See FlukeView Forms documentation for information on setting up that application. When controlling the Meter with FlukeView Forms, ECHO must be set to NO ECHO and the Fluke 45 Command language must be selected.

Select the address digit to adjust by pressing either <-- or -->.

With the desired digit selected, press the soft key labeled -- to decrement the digit or ++ to increment the character.

Interconnections

The Meter communicates with a host through a DB-9 interface connector on the rear panel of the Meter. Connect the Meter to the host or terminal using a cable appropriate to your application that is less than 50 feet (15 meters) long. Longer cables are permitted, providing that the load capacitance measured at the interface point (including the signal terminator) does not exceed 2500 picofarads.

Figure 1 shows the pin-out of the Meter’s RS-232 port, and two possible cable connections for communicating with a PC.

Fluke 8842A Emulation Mode

The Fluke 8842A emulation mode is only available when the Meter has the IEEE-488 port selected. To change the Meter to Fluke 8842A Emulation Mode, setup the remote interface for IEEE-488 (Fluke 8842A emulation mode will not work over RS-232 or Ethernet):

1. Press I

2. Press PORT IF softkey.

3. Press the SELECT PORT softkey.

4. Press the IEEE488 softkey.

Set the IEEE-488 address to a system compatible value as follows:

1. Press

2. Press PORT IF softkey.

Digital Multimeter

Configuring the RS-232 Port

3. Press the IEEE488 softkey.

4. Use the softkeys to set the address as follows.

Select the address digit to adjust by pressing either <-- or -->.

With the desired digit selected, press the soft key labeled -- to decrement the digit or ++ to increment the character.

5. With the desired address set, press ENTER.

To set the Meter to Fluke 8842A emulation:

1. Press I.

2. Press the COMMANDS softkey.

3. Press the 8842 softkey.

8845A/8846A

Programmers Manual

8845A/8846A Cable (Null Modem such as Fluke RS43) PC

Not Used

RxData

TxData

Not Used

GND

Not Used

RTS

CTS

Not Used

8845A/8846A

Not Used

RxData

TxData

Not Used

GND

Not Used

RTS

CTS

Not Used

No Connect

RxData

TxData

DTR

GND

DSR

RTS

CTS

No Connect

Cable (USB to RS-232 such as Fluke 884X-USB) PC

No Connect

RxData

TxData

DTR

GND

DSR

RTS

CTS

No Connect

DCD

RxData

TxData

DTR

GND

DSR

RTS

CTS

USB

Adapter

DCD

RxData

TxData

DTR

GND

DSR

RTS

CTS

USB

Interface

Keys

DCD RxData TxData DTR GND

Data Carrier Detect

Receive Data

Transmit Data

Data Terminal Ready

Circuit Ground

DSR RTS CTS RI

Figure 1. RS-232 Pin-out and Cable Interconnect

Configuring the Ethernet (LAN) Port

The Meter can be remotely controlled through the LAN port on the Meter’s rear panel. To select the LAN port as the remote control port, see the “Selecting the Remote Interface” section above.

Configuring the LAN port is accomplished through the Instrument Setup function. The selectable LAN port parameters are: DHCP (Dynamic Host Configuration Protocol), IP Address, Net mask, Host Name, Mac Address, Gateway, Port number, and Domain.

When setting IP addresses, subnet masks, and default gateways on the Meter, keep in mind they are stored as 32-bit binary numbers and expressed as four 3-digit segments in

Data Set Ready

Request to Send

Clear to Send

Ring Indicator

caw058.eps

Digital Multimeter

Configuring the Ethernet (LAN) Port

dot-notation form. For example, xxx.xxx.xxx.xxx, where xxx is a byte value, is stored as a 32-bit binary number.

To set the LAN port parameters:

1. Press I.

2. Press the PORT IF soft key.

3. Press the LAN soft key.

Note

When addressing some LAN addresses, computers will often interpret 0's in the IP address as OCTAL values. As an example, if you configure your IP address from the front panel as 129.196.017.023 and then attempt to establish a connection to the meter, you should connect using the IP address 129.196.17.23. Attempting to establish a connection to

129.196.017.023 may result in a connection request to 129.196.15.19.

Setting the IP Address

An internet (IP) address is required for all internet and TCP/IP communications. If DHCP is enabled, the Meter will use the dynamic address supplied by the DHCP server. However, if the DHCP server fails to supply the address, or DHCP is disabled, the currently configured static IP address will be used.

Selecting Dynamic Host Configuration Protocol (DHCP)

Dynamic Host Configuration Protocol (DHCP) is a client-server protocol that eliminates having to manually set permanent/static IP addresses. The DHCP server provides configuration parameters (dynamic IP address, subnet mask, and default gateway IP addresses) which are required for a client to participate in an IP network.

Using DHCP is the easiest way to configure the Meter for remote communication through the LAN interface. DHCP is enabled when the Meter is shipped from the factory. When connected to a network, and the LAN port is enabled, the Meter will try and retrieve the parameters from a DHCP server necessary for communications. If the parameters can’t be obtained, the Meter switches to the parameters that were manually entered into the Meter.

To disable or enable DHCP on the Meter:

From the PORT IF menu, press LAN. If DHCP is already enabled, then DHCP will be highlighted in the display. Pressing DHCP will toggle between enabled and disabled.

Note

After changing any Ethernet setting (except the socket port), the Meter must be powered off and on again, using the rear-panel power switch, to make the change active.

Setting a Static Internet Address

The Meter comes from the factory with 000.000.000.000 in the static IP address register.

Note

If you are planning to use the Meter on a corporate LAN and do not wish to use DHCP, contact your network administrator for a static IP address to be used exclusively by your Meter. DHCP must be disabled to set a static IP address.

8845A/8846A

Programmers Manual

To change the Meter’s static IP Address:

1. From the LAN Port setup menu, press the IP_ADDR soft key.

2. Use the soft keys to set the IP Address as follows:

3. Press the ENTER soft key.

Setting the LAN Subnet Mask

If communication between the host computer and the Meter passes through a router or gateway, and DHCP is disabled, you must set the subnet mask and default gateway address on both the host computer and the Meter. Get the correct subnet mask and gateway address from your network administrator.

To select the address character to adjust, press either <-- or -->.

With the desired digit selected, press the soft key labeled -- to decrement the digit or ++ to increment the digit.

Note

The IP address is stored in non-volatile memory, and does not change when power is removed and reapplied to the Meter or when the Meter receives an *RST command.

The LAN Subnet Mask is a 32-bit number. This number is represented as four 3-digit segment numbers on the front-panel display. The default subnet mask set at the factory is

255.255.254.0.

To change the Meter’s subnet mask:

1. From the LAN Port setup menu, press the NETMASK soft key.

2. Use the soft keys to set the subnet mask as follows:

To select the mask character to adjust, press either <-- or -->.

With the desired digit selected, press the soft key labeled -- to decrement the digit or ++ to increment the digit.

3. Press the ENTER soft key.

The new Subnet Mask will not take effect until the Meter has been powered down and back up again using the rear-panel power switch.

Reading the Domain Name

The Domain Name is supplied by the DHCP server and cannot be changed. To read the domain name:

1. From the LAN Port setup menu, press MORE.

2. Press the DOMAIN soft key.

3. Press B to return to the LAN Port setup menu.

Configuring the Host Name

The Host Name is the host portion of the domain name, which is translated into an IP address. The Meter’s default host name is “test1”.

To change the Host Name:

Digital Multimeter

Configuring the Ethernet (LAN) Port

1. From the LAN Port setup menu, press the HOSTNAME soft key.

2. Use the soft keys to set the Host Name as follows:

To select the character to adjust, press either <-- or -->.

With the desired character selected, press the soft key labeled -- to decrement the character or ++ to increment the character.

3. Press the ENTER soft key.

The new Host Name will not take effect until the Meter has been powered down and back up again using the rear-panel power switch.

Reading the MAC Address

The MAC Address is set at the factory and cannot be changed. To read the MAC Address:

1. From the LAN Port setup menu, press MORE.

2. Press the MAC_ADDR soft key.

3. Press B to return to the LAN Port setup menu.

Configuring the LAN Default Gateway

The default gateway IP address is the IP address of a gateway (router) attached to the same network as the device. When the instrument detects that a host computer is not on the same network (using the network number), the data is sent through the gateway to reach the host computer.

The default for the Meter is “0” (no gateway, and subnetting is not being used).

To set the LAN Default Gateway address:

1. From the LAN Port setup menu, press MORE.

2. Press GATEWAY.

3. To select the digit to adjust, press either <-- or -->.

With the desired digit selected, press the soft key labeled -- to decrement the digit or ++ to increment the digit.

4. Press the ENTER soft key.

The new gateway address will not take effect until the Meter has been powered down and back up again using the rear-panel power switch.

Configuring the General Network Socket Port

In order to communicate with each other, a host computer and the Meter must use the same socket port number. The default port is 3490. Typically, the default port does not need to be changed. If the socket port must be changed, enter the Socket Port number supplied by your network administrator.

To change the Socket Port number:

1. From the LAN Port setup menu, press the MORE soft key.

2. Press the PORT # soft key.

8845A/8846A

Programmers Manual

3. To select the digit to adjust, press either <-- or -->.

4. Press the ENTER soft key.

The new Network Socket Port becomes effective immediately.

Establishing an Ethernet Connection

The easiest method of establishing an Ethernet connection with the Meter is through the commonly available program: Telnet. Telnet is a client-server protocol, based on TCP. The Telnet Protocol provides a fairly general, bi-directional, eight-bit byte oriented communications facility. Telnet is available on all UNIX servers and on most PCs.

Telnet clients typically connect to hosts on socket port 23. The LAN connection to the Meter must be established using the specified Network Socket Port. See the “Configuring the General Network Socket Port” section above. When the remote interface port is changed to LAN from the Meter’s front panel, a LAN server is initiated in the Meter which listens for client connections on the socket port at the specified IP address.

With the desired digit selected, press the soft key labeled -- to decrement the digit or ++ to increment the digit.

Note

The Network Socket Port Number is stored in non-volatile memory.

To establish a LAN connection to the Meter from a computer using either UNIX, LINUX, or MS-DOS command prompts, perform the following procedure:

1. On the Meter’s front panel, change the remote interface port to LAN

2. At the command prompt on the client computer, enter:

telnet <IP Address> <Socket Port>

Alternatively, if you are using DHCP and would like to connect using the host name

rather than the IP address, from the computer command prompt enter:

telnet <Domain Name> <Socket Port>

As an example, if you know the IP address is 129.196.136.131 and the Socket Port is set to 3490, enter the following at a command prompt from any client computer:

telnet 129.196.136.131 3490

If you are using DHCP and the host name is test1 and the fully qualified domain name is test1.na.flukecorp.com and the Socket Port is set to 3490, enter the following at the computer command prompt:

telnet test1.na.flukecorp.com 3490

Once the internal LAN server connects with the client computer, the LAN server will reject any other connection attempts by other computers and will “tunnel” a channel to the connected computer. This prevents multiple computers from trying to control the Meter.

Digital Multimeter

Terminating an Ethernet Connection

When you wish to terminate the Ethernet connection, you may do so one of two ways:

1. Change the Meter’s remote interface port to something other than LAN

2. Terminate the Telnet session on the client computer

If you have established a LAN connection to the Meter using Telnet and change the remote interface port using the Meter’s front panel, the LAN server in the Meter will automatically terminate the Telnet session on the client computer.

On the other hand, you may wish to terminate the Telnet session on the client computer but maintain the current LAN remote interface port configuration. Client Telnet session termination can vary from computer to computer, but typically terminating the shell (or command window in DOS) will terminate the telnet session. When the client terminates the Telnet session, the LAN server in the Meter will go back into listen mode waiting for a new client to make a LAN connection request.

Selecting the Programming Language

The Meter’s remote command set is switchable between 8845A/46A, 8842A, and Fluke 45 commands. The Meter’s standard remote command set (8845A/46A) is compatible with Agilent’s 34401A SCPI command set. Although every effort was made to make the Meter compatible with Fluke 45 commands and 8842A commands, there are some commands that are not compatible. See Appendix B, “Fluke 45 Emulation Limitations” for details on Fluke 45 commands that are not compatible with this Meter. See Appendix D, “Fluke 8842A Emulation Limitations” for details on Fluke 8842A commands that are not compatible with this Meter.

To change the Meter’s remote command set:

1. Press I.

2. Press the COMMANDS soft key.

3. Press the soft key labeled with the desired command set.

Getting Started With an Installation Test

After the Meter has been cabled to a host, and prepared to communicate with it via the RS-232 or IEEE-488 interface (as described above), test the system to verify that it is operational.

Installation Test for RS-232 Connections

The procedure below illustrates how the Meter performs a computer interface command, and at the same time, confirms that the Meter has been properly set up and connected for RS-232 remote operation:

1. Press the POWER button to turn on the Meter.

2. Start up a computer terminal program.

3. Verify that the computer interface parameters (e.g., baud, parity) are set correctly.

4. Send the Meter the following command.

*IDN? <CR>

5. Verify that the Meter sends the following response:

8845A/8846A

Programmers Manual

Installation Test for IEEE-488 Connections

The procedure below illustrates how the Meter performs a computer interface command, and at the same time, confirms that the Meter has been properly set up, and connected for IEEE-488 operation:

1. Turn on the Meter.

2. Verify that the meter's IEEE-488 address is set correctly.

3. Turn on the host or controller.

4. Enter the following at the host:

In Fluke 8845A mode (includes 8846A): Fluke, 884XA, nnnnnnnm, mm/dd/yy – tt:tt

In Fluke 45 mode: FLUKE, 45, nnnnnnn, n.n Dn.n

In these results, nnnnnnn is your Meter's serial number; n.n identifies the main software version; and Dn.n identifies the display software version.

Note

This is a BASIC program to give an idea of how the test could be done. Syntax may vary with the host.

INIT PORT 0<CR> CLEAR PORT 0<CR> PRINT @<address of meter>, "*IDN?"<CR> INPUT LINE @<address of meter>, A$<CR> PRINT A$<CR>

5. Verify that the meter sends the following response

In Fluke 8845A mode (includes 8846A): Fluke, 884XA, nnnnnnnm, mm/dd/yy – tt:tt

In Fluke 45 mode: FLUKE, 45, nnnnnnn, n.n Dn.n

In these results, nnnnnnn is your meter's serial number, n.n identifies the main software version, and

If The Test Fails

If the Meter does not respond to the test procedure as indicated:

1. Check all cable connections.

2. Check to see the remote interface has been properly enabled and addressed.

Dn.n identifies the display software version.

Digital Multimeter

How the Meter Processes Input

The following paragraphs summarize how the Meter processes input that is received from a host or stand-alone terminal.

Note

In this manual, input means a string sent to the Meter from a host. Output means a string sent from the meter through the computer interface to the host.

Input Strings

The meter processes and executes valid input strings sent by the host. A valid input string is one or more syntactically correct commands followed by an input terminator.

When the meter receives input, it stores it in a 350-byte input buffer.

Note

Input strings received over the RS-232 interface are not executed or checked for proper syntax until an input terminator is received or the input buffer becomes full.

The Meter accepts alphabetic characters in either upper- or lower-case. If a command cannot be understood (i.e. the equivalent of an IEEE-488 Command Error), the remainder of the command line is ignored.

Input Terminators

An input terminator is a character or command (IEEE-488.1) sent by the host that identifies the end of a string.

In RS-232 applications, when the Meter receives an input terminator, it executes all commands entered since the last terminator was received on a first-in, first-out basis.

As input characters are processed and executed, space is made available in the input buffer for new characters. In RS-232 applications, if a communications error (e.g., parity, framing, over-run) is detected, a device-dependent error is generated, and the input string is discarded. If the Meter's input buffer becomes full when it is used with the RS-232 interface, a device-dependent error is generated (see "Event Status and Event Status Enable Register"), and the input string is discarded. If, on the other hand, the input buffer becomes full when the IEEE-488 interface is used, the Meter stops accepting characters until there is room in the buffer. Characters in the input buffer cannot be over-written with the IEEE-488 interface.

Valid terminators for the RS-232 interface are:

• LF (Line Feed)

• CR (Carriage Return)

• CR LF (Carriage Return/ Line Feed)

Valid terminators for the IEEE-488 interface are:

• EOI (End or Identity) on any character

• LF (Line Feed)

In some instances, a terminator is automatically transmitted at the end of the host's output string (i.e., the Meter's input string). For example, in Fluke BASIC, the PRINT statement finishes with a CR LF pair.

8845A/8846A

Programmers Manual

Typical IEEE-488 Input Strings

Two typical strings that could be sent to the Meter over the IEEE-488 interface are shown in Figure 2. These strings are written in BASIC to be sent from an instrument controller or computer.

Sending Numeric Values to the Meter

Numeric values can be sent to the Meter as integers, real numbers, or real numbers with exponents, as shown in the following examples:

EXAMPLE EXPLANATION

+12345689 Sends the signed integer +12345689

-1.2345E2 Sends -1.2345 x 10

Sending Command Strings to the Meter

Observe the following rules when you construct strings to be sent to the Meter over the computer interface:

• RULE 1: READ METER'S OUTPUT BUFFER ONLY ONCE FOR EACH QUERY

COMMAND.

The Meter’s output buffer is cleared after it is read. This prevents previously read data from being read a second time by mistake. If you attempt to read the meter’s output buffer twice without an intervening query, the Meter will not respond to the second read.

• RULE 2: READ QUERY RESPONSES BEFORE SENDING ANOTHER QUERY

COMMAND STRING.

Output data remains available in the output buffer until read by the host or until the next command string is received by the Meter. This means the Meter’s output buffer must be read by the host before, and not after, the next command string is sent to the Meter.

• RULE 3: THE METER EXECUTES EACH COMMAND COMPLETELY, IN THE

ORDER RECEIVED, BEFORE MOVING ON TO THE NEXT COMMAND.

If an input string contains a trigger, enter the commands in the following order, that is, from left to right, as written:

1. Commands (if any) to configure the Meter.

2. The trigger command.

3. Commands to read the result of a triggered measurement (FETCh? or READ? for

the 884XA and VAL? for the Fluke 45 emulation), or to reconfigure the instrument (if any).

4. The terminator.

Figure 2 gives two examples of a command string for the Meter. The first example is a command recognized by the Meter in the 8845A or 8846A command mode. The second example is for the Fluke 45 command mode.

Digital Multimeter

In the following examples, <space> between commands is for readability only. However a <space> between a command and its argument is required. The PRINT command sends a terminator at the end of the string.

How the Meter Processes Input

EXAMPLE 1:

The following string configures the Meter and triggers an ohms reading to be shown on the primary display when the Meter is in 8845A or 8846A command mode.

IEEE-488 bus address

Reset to power-up configuration

Select function 1 ohm range

Select 1 PLC measurement rate

Select Bus triggering

Wart-for-trigger state

Trigger a reading

Return reading shown on primary display

EXAMPLE 2:

The following string configures the Meter and triggers an ohms reading to be shown on the primary display when the Meter is in Fluke 45 emulation mode.

PRINT @3, "*RST; CONF:RES 1; :RES:NPLC 1; :TRIG:SOUR BUS; :INIT; *TRG; FETCH?"

PRINT @3, "*RST;

IEEE-488 bus address

Reset to power-up configuration

Select function

Select 300 range

Select medium reading rate

Select external trigger (Rear panel trigger disabled, no trigger delay)

Trigger a reading

Return reading shown on primary display

Figure 2. Typical IEEE-488 Input String

OHMS; RANGE 1; RATE M; TRIGGER 2; *TRG; VAL1?"

aam19f.eps

8845A/8846A

Programmers Manual

How the Meter Processes Output

The following paragraphs summarize how the Meter processes output. The Meter outputs an alphanumeric string in response to a query command from the host. Query commands are easily identified because they all end with "?". An output string is terminated by a Carriage Return and Line Feed (<CR><LF>) for RS-232 or Ethernet applications, or a Line Feed with End or Identity (<LF><EOI>) for IEEE-488.

After sending the Meter a query command via the RS-232 interface, wait for the Meter to return a prompt before sending another query command. Although the Meter will accept and process all commands other than a query command, a device-dependent command error is generated; and the second command is discarded if it is a query command.

If the Meter is part of an IEEE-488 bus system, the output data is not actually sent onto the bus until the host addresses the Meter as a talker. When the output buffer is loaded, the Message Available (MAV) bit in the Status Byte Register is set true. (For more information, see "Status Byte Register.”)

Numeric output from the Meter is displayed as shown in the following examples:

EXAMPLE EXPLANATION

+1.2345E+0 Measured value of 1.2345

+1.2345E+6 Measured value of 1.2345 x 10

Triggering Input

While under remote control, the Meter must be placed in a wait-for-trigger state before a measurement can be triggered. The INITiate and READ? commands set the Meter in to a wait-for-trigger state. The number of measurements (samples) and the number of triggers the Meter will accept after being put in a wait-for-trigger state are variables set using remote commands. The defaults for these variables are one sample per trigger and one trigger per wait-for-trigger state. See the Trigger and Sample remote commands to set these values.

All available trigger methods fall into two basic categories:

• Internal triggering uses the Meter’s internal trigger circuit for a continuous source of

triggers.

• External triggering comes from a source outside the Meter controlled by the user.

Internal Triggering

When the Meter’s trigger source is set to immediate, measurements are triggered by the Meter’s internal trigger circuit. As an example, with the sample count set to 5 and the trigger count set to 2, the Meter will collect 10 measurements after it receives an INITiate or READ? command and then stop taking measurements. The READ? command will return all 10 readings immediately while the INITiate command must be followed by a FETCh? command to retrieve the measurements.

Digital Multimeter

Service Requests (IEEE-488 Only) and Status Registers

External Triggering

There are three methods of triggering the Meter externally:

• A trigger signal applied to the external trigger jack on the Meter’s rear panel.

When the Meter’s trigger source is set to external and the Meter is in a wait-fortrigger state, a negative-going signal on the external trigger jack will trigger a measurement cycle.

• IEEE-488.1 GET command (IEEE-488 Interface only)

• *TRG command

When the Meter’s trigger source is set to BUS and the Meter is in a wait-for-trigger state, either a *TRG or bus GET command will trigger the Meter to take measurements.

Service Requests (IEEE-488 Only) and Status Registers

Service requests let an instrument on the IEEE-488 bus get the attention of the host. Service requests are sent over the service request (SRQ) bus line.

If more than one instrument on the bus is capable of sending service requests, the host can determine which instrument made the request by taking a serial poll. Each instrument on the bus responds to the poll by sending the contents of its Status Byte Register. If an instrument on the bus has made a service request, the request service bit (RQS, bit 6) of its Status Byte Register will be set to 1, identifying it as an instrument that requested service.

The contents of the Status Byte Register (STB) is determined by the Service Request Enable Register (SRE), Standard Event Status Register (ESR), Standard Event Status Enable Register (ESE), Questionable Data Event Register, Questionable Data Enable Register, and the output buffer. These status registers are discussed below, and summarized in Table 4. Figure 3 shows the relationship of these registers.

Table 4. Status Register Summary

Status Byte Resister *STB? None SRE

Status Byte Enable Register *SRE? *SRE None

Standard Event Register *ESR? None ESE

Standard Event Enable Register

Questionable Data Event Register

*ESE? *ESE None

STAT:QUES:EVEN? None Questionable Data

Enable Register

Questionable Data Enable Register

STAT:QUES:ENAB? STAT:QUES:ENAB

<value>

None

8845A/8846A

Programmers Manual

Questionable Data Binary Wieghts

Event Register Enable Register

Voltage Overload

Current Overload1

Not Used

Not Used Not Used Not Used Not Used Not Used Not Used Not Used

Ohms Overload

Not Used Limit Test Fail LO11 Limit Test Fail HI12

Remote Mode

Not Used

STAT:QUES:EVEN? STAT:QUES:ENAB <value>

STAT:QUES:ENAB?

Standard Event

"OR"

20 = 1 2 2 2 2 2 2 2 2

3 4 5 6

Event Register Enable Register

Operation Complete

Not Used

Query Error2 Device Error3

Execution Error4

Command Error

Not Used

Power On

*ESR? *ESE <value>

*ESE?

"OR"

Figure 3. Overview of Status Data Structure (8845A/8846A and Fluke 45)

= 2 2

= 4 210 = 1024

= 8 211 = 2048

= 16 212 = 4096

= 32 213 = 8192

= 64 214 = 16384

= 128 215 = 32768

= 256

= 512

Status Byte

Summary Register Enable Register

Not Used Not Used

Not Used Questionable Data Message Available

Standard Event

Request Service

Not Used

Serial Poll (SPOLL) *STB?

*SRE <value> *SRE?

Output Buffer

"OR"

caw01f.eps

Standard Event Status and Standard Event Status Enable Registers

The Standard Event Status Register (ESR) assigns events to specific bits (see Figure 3 and Table 5). When a bit in the ESR is set (for example, 1), the event that corresponds to that bit has occurred since the register was last read or cleared. For example, if bit 3 (DDE) is set to 1, a device-dependent error has occurred.

The Standard Event Status Enable Register (ESE) is a mask register that allows the host to enable or disable (mask) each bit in the ESR. When a bit in the ESE is 1, the corresponding bit in the ESR is enabled. When any enabled bit in the ESR changes from O to 1, the Standard Event bit in the Status Byte Register also goes to 1. When the ESR is read (using the *ESR? command) or cleared (using the *CLS command), the Standard Event bit in the Status Byte Register returns to 0.

Digital Multimeter

Table 5. Description of Bits in ESR and ESE

Bit No. Name True (Set to 1) Conditions

Service Requests (IEEE-488 Only) and Status Registers

Operation Complete (OPC)

Not used

Query Error (QYE)

Device-Dependent Error (DDE)

Execution Error (EXE)

Command Error (CME)

Not used

Power On

All commands previous to receipt of an *OPC command have been executed. Interface is ready to accept another message.

Always set to zero.

Attempt has been made to read data from the Meter's output buffer when no output is present or pending. Possibly a new command line has been received before a previous query has been read or both input and output buffers are full.

Incorrect input during calibration, or RS-232 input buffer overflow.

Command was understood but could not be executed. Results from, for example, an inappropriate parameter.

Command not executed because it was not understood. This condition might occur when, for example, a command sent to the meter contained a syntax error.

Always set to zero.

(PON) Power has been cycled off and on since the last time the ESR was read or cleared.

Questionable Data Event Register and Questionable Data Enable Register

The Questionable Data Event Register provides information about the Meter’s measurements. Information such as overload conditions, high/low limits, and whether or not the Meter is in remote mode can be reported through the questionable data summary bit. Once a bit is set by the Meter, it remains set until it is read from the register or is cleared. The sixteen bits of the Questionable Data Event Register are described in Table

The Questionable Data Enable Register determines which of the bits in the Questionable Data Event Register will be used to the set the Questionable Data Summary bit in the Meter’s Status Byte. When a bit in the Questionable Data Enable Register is 1, the corresponding bit in the Questionable Data Event Register is enabled. When any enabled bit in the Questionable Data Event Register changes from 0 to 1, the Questionable Data bit in the Status Byte Register also goes to 1. When the Questionable Data Event Register is read (using the STAT:QUES:EVEN? command) or cleared (using the *CLS command), the Questionable Data bit in the Status Byte Register returns to 0.

8845A/8846A

Programmers Manual

Table 6. Description of Bits in the Questionable Data Register

Bit No. Name True (Set to 1) Condition

0 Voltage Overload

1 Current Overload

2 – 8 Not Used

9 Ohms Overload

10 Not Used

11 Limit Test Fail Lo

12 Limit Test Fail Hi

13 Remote Mode The Meter is set in remote mode.

14 – 15 Not Used

Status Byte Register

The Status Byte Register (STB) is a binary-encoded register that contains eight bits. Note that the Service Request Enable Register (SRE) uses bits 1 through 5, and bit 7 to set, the request service (RQS) bit 6, as enabled by the SRE. When the RQS bit is set true (l), the Meter sets the SRQ line true (1), which generates a service request. The eight bits of the Status Byte Register (as read by the *STB? command) are described in Table 7.

Input voltage has exceeded the upper limit of the range.

Input current has exceeded the upper limit of the range.

The resistance measurement has exceeded the upper limit of the range.

The measurement is below the low end of the test limit.

The measurement is above the high end of the test limit.

Reading the Status Byte Register

The host can read the Status Byte Register by performing a serial poll, or sending the Meter a *STB? query. The value of the status byte is not affected by the *STB? query. When the Status Byte Register is read, an integer is returned. This integer is the decimal equivalent of an 8-bit binary number. For example 48 is the decimal equivalent of the binary 00110000, and means that bit 4 (Message Available) and bit 5 (Standard Event) are set to “1”.

If the status byte is read by serial poll, bit 6 is returned as a request service (RQS); if it is read with an *STB? query, bit 6 is returned as Master Summary Status (MSS).

EXAMPLE EXPLANATION

*STB? Reads the Status Byte Register. Assume that “32” is returned. Converting 32

to the binary 00100000 indicates that bit 5 (Standard Event) is set to 1. To determine the event status, you would have to read the Standard Event Register in the same manner, using the *ESR? command.

Digital Multimeter

Table 7. Description of Bits in the Status Byte Register

Bit No. Name True (Set to 1) Condition

0 Not used Always set to 0.

1 Not used Always set to 0.

2 Not used Always set to 0.

3 Questionable Data One or more of the enabled events in the

4 Message Available (MAV) Data is available in the output buffer. Bit set to 1

5 Standard Event Status (ESB) One or more of the enabled events in the Event

Service Requests (IEEE-488 Only) and Status Registers

Questionable Data Event Register have occurred. To determine which Questionable Data events have occurred, send the Meter STAT:QUES:EVEN? to read the Questionable Data Event Register.

when response to query placed in output buffer. Bit cleared (set to 0) when output terminator sent to host.

Status Register have occurred. To determine which events have occurred, send the Meter *ESR? to read the Event Status Register.

6 Master Summary Status† (MSS) Set to 1 if any enabled bit in the STB (MSS) register

is set to 1, otherwise set to 0. Status of MSS bit returned by *STB? query command.

Request Service (RQS) Set to 1 if service requested from front panel, or MSS set to 1. Status of bit returned by serial poll, which clears RQS.

7 Not Used Always set to zero.

† As read by *STB? command. If the Status Byte Register is read by a serial poll, bit 6 is returned as RQS.

Service Request Enable Register

The SRE Register is an 8-bit register that enables or disables (i.e., masks) corresponding summary messages in the Status Byte Register.

The Meter may be programmed to make a service request on errors, questionable data, or when output is available. Conditions that trigger a service request are specified by writing a binary weighted value to the SRE Register, using the *SRE command.

EXAMPLE EXPLANATION

*SRE 16 Enables the generation of an SRQ when bit 4 (Measurement

Available) in the Status Byte Register is set to 1. 16 is the decimal equivalent of 00010000 binary. This means that bit 4 in SRE Register (that corresponds to the Measurement Available bit in the Status Byte Register) is 1, and all other bits are 0.

EXAMPLE EXPLANATION

*SRE 48 Enables the generation of an SRQ when bits 4 or 5 (Measurement

Available or Standard Event) in the Status Byte Register are set to 1. The binary equivalent of 48 is 00110000, indicating that bits 4 and 5 are set to 1.

8845A/8846A

Programmers Manual

If any bit in the SRE is set to 1, the RQS bit (bit 6) in the Status Byte Register is enabled, meaning a service request can be generated when the appropriate bits in STB become 1.

Use the *SRE? query (see Table 10) to read the SRE Register. The Meter returns a binary-weighted integer that represents the enabled bits in the register. (The value of bit 6 will always be zero.) Convert the returned value to binary to determine the status of register bits.

EXAMPLE EXPLANATION

*SRE? Reads the value of the SRE Register. Assume "32" is returned.

Supported SCPI Commands

This section explains the SCPI (Standard Commands for Programmable Instruments) commands available to program the Meter. This section includes the following information:

• A list of the supported SCPI Commands

• A discussion of how to use the command set

• A detailed description of each command in the set

• Error handling for the 8845A/8846A

Converting 32 to the binary 00100000 indicates that bit 5 in the SRE is set to 1.

Throughout this document, the following conventions are used for SCPI command syntax. Square brackets ( [ ] ) indicate optional keywords or parameters. Braces ( { } ) enclose parameters within a command string. Triangle brackets ( < > ) indicate that you must substitute a value for the enclosed parameter.

SCPI Command Summary

Tables 7 through 16 summarize the SCPI commands implemented in the 8845A and 8846A Digital Multimeters.

Table 8. CALibration Command Summary

Command Description

CALibration? [{on|off}] CALibration :COUNt? :RECord :SECure :CODE <new code> :STATe {off|on}, <code> :STATe? :STRing <quoted string> :STRing? :DATE <date> :DATE? :VALue <value> :VALue? :STEP <step #>[,Reference] :STEP?

Note

Perform a calibration Path to the calibration function Retrieves number of times Meter has been calibrated Records calibration values Path to calibration security function Change security code Unsecure / secure calibration mode Retrieves state of security mode Record calibration information Retrieves calibration information Set the calibration date Retrieve the calibration date Specify calibration signal value Retrieves calibration signal value Set the calibration step and reference Retrieve the calibration step

Digital Multimeter

Table 9. CONFigure Command Summary

Command Description

Supported SCPI Commands

CONFigure[:SCALar] [:VOLTage] [:DC [{range}[, {resolution}]]] :RATio :AC [{range}[, {resolution}]] :CURRent [:DC[ {range}][, {resolution}]]] :AC [{range}][, {resolution}]] :RESistance [{range}[, {resolution}]] :FRESistance [{range}[, {resolution}]] :FREQuency [{range}[, {resolution}]] :PERiod [{range}[, {resolution}]] :CAPacitance [{range}[, {resolution}]] :TEMPerature:FRTD [{<RTD Type>}] :TEMPerature:RTD [{<RTD Type>}] :CONTinuity :DIODe [{low current}][, {high voltage}]] CONFigure?

Table 10. IEEE-488.2 Common Command Summary

Command Description

*CLS

*ESE <enable value> *ESE?

Subsystem to set Meter function Path to set voltage function Selects dc volts function Selects dc volts ratio function Selects ac volts function Path to set current function Selects dc current function Selects ac current function Selects resistance function Selects 4-wire resistance function Selects frequency function Selects period function Selects capacitance function Selects 4-wire temperature function Selects 2-wire temperature function Selects continuity function Selects diode function Retrieves present Meter configuration

Clear status byte summary, and all event registers

Enable bits in standard event register Retrieve standard event enable register

*ESR?

*IDN?

*OPC *OPC?

*PSC {0|1} *PSC?

*RST

*SRE <enable value> *SRE?

*STB?

*TST

*TRG

Retrieve standard event register

Retrieve meter’s identification string

Set ‘Operation Complete” bit in Standard event reg. Returns “1” in output buffer after command execution.

Power-on status clear Retrieve power-on status clear setting

Reset Meter to its power-on state

Enable bits in status byte register Retrieve bits in status byte register

Retrieve the status byte summary register

Perform self-test. Returns “0” if the test succeeds, “1” if the test fails.

Trigger a measurement

8845A/8846A

Programmers Manual

Table 11. Math Command Summary

Command Description

CALCulate :AVERage :MINimum? :MAXimum? :AVERage? :COUNt? :DB :REFerence {<value>|MINimum|MAXimum} :REFerence? :DBM :REFerence {<value>|MINimum|MAXimum} :REFerence? :FUNCtion {NULL|DB|DBM|AVERage|LIMIt} :FUNCtion? :KMATh :STATe { on|off} :MMFactor{<value>} :MMFactor? :MBFactor{<value>} :MBFactor? :MUNits{<name>} :MUNits? :LIMit :LOWer{<value>|MINimum|MAXimum} :LOWer? :UPPer{<value>|MINimum|MAXimum} :UPPer? :NULL :OFFSet {<value>|MINimum|MAXimum} :OFFSet? [MINimum|MAXimum] :STATe {ON|OFF} :STATe?

Path to the math functions Path to MIN-MAX function Retrieves the recorded minimum value Retrieves the recorded maximum value Retrieves the recorded average value Retrieves the number of readings during MIN-MAX run Path to DB function Store relative value in relative register

Retrieves the relative value from the relative register Path to DBM function Select dBm reference value

Retrieves the present dBm reference value Sets the math function

Retrieves the present math function Path to math functions Disables/enables mx+b calculations Sets the value of “m” for mx+b Reads the value of “m” for mx+b Sets the value of “b” for mx+b Reads the value of “b” for mx+b Sets the units name for mx+b Reads the units name for mx+b Path to limit testing function Set the lower limit for limit testing Retrieves the lower limit Set the upper limit for limit testing Retrieves the upper limit Path to null function Sets the offset value Retrieves set or maximum or minimum offset value. Disable/enable selected math function Retrieves the state of the math function

DATA :FEED RDG_STORE, {“CALCulate”|” ”} :FEED?

Table 12. MEASure Command Summary

Command Description

MEASure[:SCALar] :CAPacitance? [{<range>|MIN|MAX|DEF}[{,<resolution>|MIN|MAX|DEF}]] :CONTinuity? :CURRent :DC? [{<range>|MIN|MAX|DEF}[, {<resolution>|MIN|MAX|DEF}]] :AC?

Path to storing readings taken with INITiate command Enables/disables storing of INITiate readings Retrieves state of storing INITiate readings

Path to measure control Preset and make capacitance measurement Make a continuity measurement Path to measure current Make a dc current measurement

Make an ac current measurement

Digital Multimeter

Table 12. MEASure Command Summary (cont.)

Command Description

Supported SCPI Commands

[{<range>|MIN|MAX|DEF}[{,<resolution>|MIN|MAX|DEF}]] :DIODe? [{low current}][, {high voltage}]] :FREQuency? :FRESistance? [{<range>|MIN|MAX|DEF}[{,<resolution>|MIN|MAX|DEF}]] :PERiod? [{<range>|MIN|MAX|DEF}[{,<resolution>|MIN|MAX|DEF}]] :RESistance? [{<range>|MIN|MAX|DEF}[{,<resolution>|MIN|MAX|DEF}]] :TEMPerature:FRTD? [{<RTD Type}] :TEMPerature:RTD? [{<RTD> Type>}] :VOLTage :AC? [{<range>|MIN|MAX|DEF}[{,<resolution>|MIN|MAX|DEF}]] [:DC]? [{<range>|MIN|MAX|DEF}[{,<resolution>|MIN|MAX|DEF}]] :RATio?

Table 13. Measurement Configuration Command Summary

[1]

Command

[SENSe:] FUNCtion[1/2] “CAPacitance” FUNCtion[1/2] “CONTinuity” FUNCtion[1/2] “CURRent:AC” FUNCtion[1/2] “CURRent:DC” FUNCtion[1/2] “DIODe” FUNCtion[1/2] “FRESistance” FUNCtion[1/2] “FREQuency” FUNCtion[1/2] “PERiod” FUNCtion[1/2] “RESistance” FUNCtion[1/2] “TEMPerature:FRTD” FUNCtion[1/2] “TEMPerature:RTD” FUNCtion[1/2] “VOLTage:DC” FUNCtion[1/2] “VOLTage:AC” FUNCtion[1] “VOLTage:RATio” FUNCtion[1/2] ? FUNCtion2 “None” VOLTage :AC :BANDwidth {3|20|200|MINimum|MAXimum} :BANDwidth? :RANGe {<range>|MINimum|MAXimum} :AUTO {OFF|ON} :AUTO? :RANGe? [MINimum|MAXimum] :RESolution {<resolution>|MINimum|MAXimum} :RESolution? [MINimum|MAXimum] [:DC]

Description

Path to Meter configuration Select capacitance function Select continuity function Select ac current function Select dc current function Select diode function Select 4-wire resistance function Select frequency function Select period function Select 2-wire resistance function Select 4-wire temperature function Select 2-wire temperature function Select dc voltage function Select ac voltage function Select dc voltage ratio function Retrieve present measurement function Turn off secondary display Path to configure voltage measurement range Path to ac voltage range Select filter Retrieve present filter setting Set ac voltage range Disable/Enable Autoranging Retrieve present autorange setting Retrieve the present range setting Set resolution for ac voltage measurement Retrieve ac voltage measurement resolution Path to dc voltage range

Make a diode measurement Make a frequency measurement Make a 4-wire resistance measurement

Make a period measurement

Make a 2-wire measurement

Make a 4-wire temperature measurement Make a 2-wire temperature measurement Path to voltage measurements Make an ac voltage measurement

Make a dc voltage measurement

Make a dc voltage ratio measurement

8845A/8846A

Programmers Manual

Table 13. Measurement Configuration Command Summary (cont.)

Command

[1]

Description

:FILTer [:STATe] {OFF|ON} [:STATe]? :DIGItal [:STATe]{OFF|ON} [:STATe]? :IMPedance :AUTO {OFF|ON} :AUTO? :NPLCycles {0.02|0.2|1|10|100| MINimum|MAXimum} :NPLCycles? [MINimum|MAXimum] :RANGe {<range>|MINimum|MAXimum} :AUTO {OFF|ON} :AUTO? :RANGe? [MINimum|MAXimum] :RESolution {<resolution>|MINimum|MAXimum} :RESolution? [MINimum|MAXimum] CURRent :AC :BANDwidth {3|20|200|MINimum|MAXimum} :BANDwidth? :RANGe {<range>|MINimum|MAXimum} :AUTO {OFF|ON} :AUTO? :RANGe? [MINimum|MAXimum] :RESolution {<resolution>|MINimum|MAXimum} :RESolution? [MINimum|MAXimum] [:DC] :FILTer [:STATe] {OFF|ON} [:STATe]? :DIGItal [:STATe]{OFF|ON} [:STATe]? :NPLCycles {0.02|0.2|1|10|100| MINimum|MAXimum} :NPLCycles? [MINimum|MAXimum] :RANGe {<range>|MINimum|MAXimum} :AUTO {OFF|ON} :AUTO? :RANGe? [MINimum|MAXimum] :RESolution {<resolution>|MINimum|MAXimum} :RESolution? [MINimum|MAXimum] RESistance :FILTer [:STATe] {OFF|ON} [:STATe]? :DIGItal [:STATe]{OFF|ON} [:STATe]?

Path to analog filter Activates or deactivates 3-pole analog filter Retrieve the present analog filter setting Path to digital filter Activates or deactivates digital filter Retrieve the present digital filter setting Path to input impedance selection Turn auto-impedance mode off or on Retrieve present setting of auto impedance Set integration time for selected function

Retrieve integration time for selected function Set dc voltage range Disable/enable Autoranging Retrieve present autorange setting Retrieve the present range setting Set resolution for dc voltage measurement Retrieve dc voltage measurement resolution Path to configure current measurement range Path to ac current range Select filter Retrieve present filter setting Set ac current range Disable/enable Autoranging Retrieve present autorange setting Retrieve the present range setting Set resolution for ac current measurement Retrieve ac current measurement resolution Path to dc current range Path to analog filter Set analog filter off or on Retrieve the present analog filter setting Path to digital filter Activates or deactivates digital filter Retrieve the present digital filter setting Set integration time for selected function

Retrieve integration time for selected function Set dc current range Disable/enable Autoranging Retrieve present autorange setting Retrieve the present range setting Set resolution for dc current measurement Retrieve dc current measurement resolution Path to 2–wire resistance measurement range Path to analog filter Set the analog filter off or on Retrieve the present analog filter setting Path to digital filter Activates or deactivates digital filter Retrieve the present digital filter setting

Digital Multimeter

Table 13. Measurement Configuration Command Summary (cont.)

Command

[1]

Description

Supported SCPI Commands

:NPLCycles {0.02|0.2|1|10|100| MINimum|MAXimum} :NPLCycles? [MINimum|MAXimum] :RANGe {<range>|MINimum|MAXimum} :AUTO {OFF|ON} :AUTO? :RANGe? [MINimum|MAXimum] :RESolution {<resolution>|MINimum|MAXimum} :RESolution? [MINimum|MAXimum} FRESistance :FILTer :STATe {OFF|ON} :STATe? :DIGItal [:STATe]{OFF|ON} [:STATe]? :NPLCycles {0.02|0.2|1|10|100| MINimum|MAXimum} :NPLCycles? [MINimum|MAXimum] :RANGe {<range>|MINimum|MAXimum} :AUTO {OFF|ON} :AUTO? :RANGe? [MINimum|MAXimum] :RESolution {<resolution>|MINimum|MAXimum} :RESolution? [MINimum|MAXimum} FREQuency :APERture {0.01|0.1|1|MINimum|MAXimum} :APERture? [MINimum|MAXimum] :VOLTage :RANGe {<range>|MINimum|MAXimum} :AUTO {OFF|ON} :AUTO? :RANGe? [MINimum|MAXimum] PERiod :APERture {0.01|0.1|1|MINimum|MAXimum} :APERture? [MINimum|MAXimum] :VOLTage :RANGe {<range>|MINimum|MAXimum} :AUTO {OFF|ON} :AUTO? :RANGe? [MINimum|MAXimum] CAPacitance :RANGe {<range>|MINimum|MAXimum} :AUTO {OFF|ON} :AUTO? :RANGe? [MINimum|MAXimum] :RESolution {<resolution>|MINimum|MAXimum} :RESolution? [MINimum|MAXimum} TEMPerature :RTD :ALPHa <alpha value>

Set integration time for selected function

Retrieve integration time for selected function Set resistance measurement range Disable/enable Autoranging Retrieve present autorange setting Retrieve the present range setting Set resolution for resistance measurement Retrieve resistance measurement resolution Path to frequency measurement range Set aperture time for frequency function Retrieve aperture time for frequency function Path to frequency range configuration Set frequency measurement range Disable/enable Autoranging Retrieve present autorange setting Retrieve the present range setting Path to period measurement range Set aperture time for period function Retrieve aperture time for period function Path to period range configuration Set period measurement range Disable/enable Autoranging Retrieve present autorange setting Retrieve the present range setting Path to capacitance measurement range Set capacitance measurement range Disable/enable Autoranging Retrieve present autorange setting Retrieve the present range setting Set resolution for capacitance measurement Retrieve capacitance measurement resolution Path to temperature measurement Path to 2-wire temperature measurement Set RTD alpha parameter

8845A/8846A

Programmers Manual

Table 13. Measurement Configuration Command Summary (cont.)

Command

[1]

Description

:ALPHa? :NPLCycles {0.02|0.2|1|10|100| MINimum|MAXimum} :NPLCycles? [MINimum|MAXimum] :R0 <R0 value> :R0? :TYPe {PT100_385|PT100_392|CUST1} :TYPe?

:FRTD :ALPHa <alpha value> :ALPHa? :NPLCycles {0.02|0.2|1|10|100| MINimum|MAXimum} :NPLCycles? [MINimum|MAXimum] :R0 <R0 value> :R0? :TYPe {PT100_385|PT100_392|CUST1} :TYPe?

FILTer [:DC] [:STATe] {OFF|ON} [:STATe]? :DIGital [:STATe]{OFF|ON} [:STATe]?

Retrieve the present RTD alpha parameter Set integration time for selected function

Retrieve integration time for selected function Set resistance at 0 °C Retrieve present 0 °C resistance setting Set the type of RTD Retrieve the present RTD type (385|CUSTOM)

Path to 4-wire temperature measurement Set RTD alpha parameter Retrieve the present RTD alpha parameter Set integration time for selected function

Retrieve integration time for selected function Set resistance at 0 °C Retrieve present 0 °C resistance setting Set the type of RTD Retrieve the present RTD type (385|CUSTOM)

Path to filter selection Path to analog filter Set analog filter off or on for dc functions Retrieve the present analog filter setting Path to digital filter Activates or deactivates digital filter Retrieve the present digital filter setting

DETector :BANDwidth {3|20|200|MINimum|MAXimum} :BANDwidth? [MINimum|MAXimum]

ZERO :AUTO {OFF|ONCE|ON} :AUTO?

INPut :IMPedance :AUTO {OFF|ON} :AUTO?

ROUTe :TERMinals?

[1] Default parameters are shown in bold

Table 14. RS-232 Interface Command Summary

Command Description

SYSTem :LOCal :REMote :RWLock

Path to ac filter selection Set the ac input signal filter Retrieve the present ac filter setting

Path to configuring the autozero mode Set the autozero mode Retrieve the present autozero mode

Path to input impedance Path to input impedance configuration Disable/enable auto input impedance select Retrieve auto input impedance mode

Path to input terminal selection Retrieve input terminal selection (front or rear)

Path to RS-232 Interface commands Set Meter to local mode Set Meter to remote mode for RS-232 operation Set Meter to remote mode (lock out front panel)

Digital Multimeter

Table 15. Status Reporting Command Summary

Command Description

Supported SCPI Commands

*CLS

*ESE <enable value> *ESE?

*ESR?

*OPC

*OPC?

*PSC {0|1} *PSC? *SRE <enable value> *SRE?

*STB?

SYSTem :ERRor?

STATus :PRESet :QUEStionable :ENABle <enable value> :ENABle? :EVENt?

Clear status byte summary and all event registers

Enable bits in standard event register Retrieve standard event enable register

Retrieve standard event register

Set Operation Complete bit in standard event register Returns “1” in output buffer after command exec.

Power-on status clear Retrieve power-on status clear setting Enable bits in status byte register Retrieve bits in status byte register

Retrieve the status byte summary register

Path to meter’s error queue Retreive meter’s error queue

Path to meter’s status system Clear questionable data enable register Path to questionable data register Enable bits in questionable data enable register Retrieve questionable data register Retrieve questionable data enable register

8845A/8846A

Programmers Manual

Command

Table 16. System-Related Command Summary

[1]

Description

FETCh[1|2|3]?

READ?

DISPlay {OFF|ON} :TEXT <quoted string> :CLEar :TEXT?

DISPlay?

SYSTem :BEEPer :STATe {OFF|ON}

:STATe? :DATE <mm/dd/yyy> :DATE? :ERRor? :ERRor:BEEPer {OFF|ON} :ERRor:BEEPer? :TIME <hh:mm:ss> :TIME? :VERSion?

DATA :POINts?

Transfer stored readings to output buffer

Set trigger system to ‘wait-for-trigger’

Turn display off or on Write message to display Clear message from display Retreive displayed message

Retrieve display setting

Path to system controls Issue a single beep Disable/enable beeper for limit, and diode testing Retrieve state of beeper Sets the Meter’s date Retrieves the Meter’s date Retrieve meter’s error queue Enable/disable beeper for errors Retrieve beeper state for errors Sets the Meter’s time Retrieves the Meter’s time Retrieve meter’s SCPI version

Path to meter’s memory Retrieve the number of stored readings

*RST

IDN [ON|OFF], [Quoted String]

*IDN?

L1 L2 L3

Reset Meter to its power-on state

Enables or disables a secondary indentification defined by the quoted string. When disabled, *IDN? will return the indentification set by the Meter’s manufacturer.

Retrieve meter’s identification string

Set the command language to 8845A/46A Set the command language to Fluke 45 Set the command language to Fluke 8842A

[1] Default parameters are shown in bold

Digital Multimeter

Table 17. Triggering Command Summary

Command

[1]

Description

Supported SCPI Commands

INITiate

DATA

:FEED RDG_STORE, {“CALCulate”|” ”} :FEED?

READ?

SAMPle :COUNt {<value>|MINimum|MAXimum} :COUNt? [MINimum|MAXimum]

TRIGger :COUNt {<value>|MINimum|MAXimum|INFinite} :COUNt? [MINimum|MAXimum] :DELay {<seconds>|MINimum|MAXimum} :AUTO {OFF|ON} :AUTO? :DELay? [MINimum|MAXimum] :SOURce {Bus|IMMediate|EXTernal} :SOURce?

[1] Bold type denotes default parameter.

[1]

SCPI Command Details

All SCPI commands recognized by the Meter are listed in the following sections along with description and syntax rules.

Set trigger system to wait-for-trigger

Path to storing readings taken with INITiate command Enables/disables storing of INITiate readings Retrieves state of storing INITiate readings

Set trigger system to wait-for-trigger

Path to sample count Set number of samples per trigger Retrieve sample count

Path to trigger control Set the number of triggers Meter will accept Retrieve the number of tiggers Meter will accept Set the delay between trigger and measurement Disable/Enable automatic trigger delay Retrieve automatic trigger delay status Retreive present trigger delay value Set meter’s trigger source Retrieve the meter’s present trigger source

8845A/8846A

Programmers Manual

Using the MEASure? Command

The MEASure? command provides the quickest and simplest program method for getting the Meter to make a single measurement through remote control. However, MEASure? does not provide control over all possible parameters associated with a measurement function. With the exception of function, range, and resolution, the MEASure? command does not allow changing settings before the measurement is taken. Instead, the Meter uses predefined settings for each function (See Table 18) and makes a measurement as soon as the command is received. The measurement is immediately sent to the output buffer.

A MEASure? command is the same as using a CONFigure command followed by the READ? Command.

MEASure[:SCALar][:<function>]?[<range> or <RTD type> or <low current> [,<resolution> or <high voltage>]]

Description Sets the Meter function with the preset parameters (See Table 18), and

makes the measurement using the specified range and resolution. The reading is placed in the output buffer. For the temperature function, the range variable is replaced by the RTD type variable.

Note

The dc portion of the function keyword is optional, as is the VOLTage portion. For instance, MEAS:AC? will be interpreted by the Meter as meaning Volts ac function.

Parameters <function> = CAPacitance Capacitance

CURRent:AC AC current CURRent:DC DC current VOLTage:AC AC voltage VOLTage:DC DC voltage VOLTage:DC:RATio DC voltage ratio

[1]

[7]

RESistance 2-wire resistance FRESistance 4-wire resistance FREquency Frequency PERiod Period TEMPerature:RTD 2-wire temperature TEMPerature:FRTD 4-wire temperature DIODe Diode CONTinuity Continuity

[5]

[3]

[2]

[6]

[4]

<range> = a number between the upper and lower limits of the

function. MIN Lowest range of the function MAX Highest range of the function DEF Autorange

<low current> = ON or 1 Sets diode current to 0.1 mA OFF or 0 Sets diode current to 1 mA

<high voltage> ON or 1 Sets diode voltage to 10 V OFF or 0 Sets diode voltage to 5 V.

<resolution> = a number in the same units, not in number of digits, as

the measurement function,. MIN Smallest value acceptable MAX Largest value acceptable DEF 5½ digits

Digital Multimeter

Supported SCPI Commands

Note

Issuing a MEASure? command without specifying a function, puts the Meter into volts dc and triggers a measurement. You must specify a range to use a resolution parameter.

Example MEAS:volt:ac? 10 = Returns a measurement after configuring the

Meter for volts ac and setting the range to the 10 volt range.

MEAS:diod? ON = Sets diode function using low current and returns

the diode measurement. 9.90000000E+37 is the value returned for an open diode.

Notes [1] For ac measurements, resolution is fixed at 6½ digits. The resolution

parameter only affects the front panel display.

[2] For frequency measurements, the multimeter uses one “range” for all

inputs between 3 Hz, and 300 kHz. With no input signal applied, frequency measurements return zero.

[3] For period measurements, the multimeter uses one “range” for all

inputs between 0.33 seconds, and 3.3 µsec. With no input signal applied, period measurements return zero.

[4] The range and resolution are fixed for temperature measurements.

However, placing PT100_385 or PT100_392 into the range field will set the RTD type. Placing CUST1 into the range field will cause the Meter to use the values set into the R

[5] The range and resolution are fixed for diode test: 10 Vdc range and 5½

digits. When set to ON, the low current parameter sets the diode test current to 0.1 mA. When OFF, the current is 1 mA. When set to ON, the high voltage parameter sets the diode test voltage to 10 volts. When OFF, the voltage is 5 volts. To specify a diode test voltage, you must also include ON or OFF for the low current parameter.

[6] The range and resolution are fixed for continuity tests: 1 kΩ range and

5½ digits.

[7] DC measurement voltage divided by dc reference voltage. For dc ratio,

connect the reference HI/LO to the HI/LO sense terminals of the Meter and the measurement voltage to the HI/LO input terminals of the Meter. Note the specified measurement range applies to the input terminals only.

For best results in RATIO, the two input commons must be shorted at the Meter terminals. The analog filter (AFLTR) should be off.

Using the CONFigure Command

The CONFigure command allows more configuration control than the MEASure command. As with the MEASure command, the CONFigure command presets the Meter’s parameters for the desired configuration (See Table 18). However, a measurement does not start automatically, and therefore affords the opportunity to change measurement parameters prior to triggering a measurement.

Note

and Alpha parameters.

The CONFigure command is very useful when most of the parameters preset by CONFigure are what you want and you only need to change one or two parameters. The

8845A/8846A

Programmers Manual

SENSe:FUNCtion command provides a means of changing a function’s parameters. Other commands, such as INPut, SENSe, CALCulate, and TRIGger allow for more detailed control of the Meter’s parameters.

The CONFigure command does not initiate a measurement and will need to be followed by READ? command, or the INITiate and FETCh? commands.

CONFigure[:SCALar][:<function>] [<range |MIN|MAX|DEF> or <RTD type> or <low current>][,<resolution |MIN|MAX|DEF> or <high voltage>]]

Description Sets the Meter function with the preset parameters (See Table 18) and

configure the Meter using the specified range and resolution. This command must be followed by a READ? command, or the INITiate and FETCh? commands to cause the Meter to take a measurement. For the temperature function, the range variable is replaced by the RTD type variable.

Note

The dc portion of the function keyword is optional, as is the VOLTage portion. For instance, CONF:AC will be interpreted by the Meter as meaning Volts ac function.

Parameters <function> = CAPacitance Capacitance

CURRent:AC AC current CURRent:DC DC current VOLTage:AC AC voltage VOLTage:DC DC voltage VOLTage:DC:RATio DC voltage ratio

[1]

[7]

RESistance 2-wire resistance FRESistance 4-wire resistance FREquency Frequency PERiod Period TEMPerature:RTD 2-wire temperature TEMPerature:FRTD 4-wire temperature DIODe Diode CONTinuity Continuity

[5]

[3]

[2]

[6]

[4]

<range> = a number between the upper and lower limits of the

function. MIN Lowest range of the function MAX Highest range of the function DEF Autorange

<low current> = ON or 1 Sets diode current to 0.1 mA OFF or 0 Sets diode current to 1 mA.

<low voltage> = ON or 1 Sets diode voltage to 5 volts OFF or 0 Sets diode voltage to 10 volts.

<resolution> = a number in the same units, not in number of digits, as

the measurement function,. MIN Smallest value acceptable MAX Largest value acceptable DEF 5½ digits

Note

You must specify a range whenever specifying a resolution parameter.

Digital Multimeter

Supported SCPI Commands

Notes [1] For ac measurements, resolution is fixed at 6½ digits. The resolution

parameter only affects the front panel display.

[2] For frequency measurements, the Meter uses one range for all inputs

between 3 Hz, and 300 kHz. With no input signal applied, frequency measurements return zero.

[3] For period measurements, the Meter uses one range for all inputs

between 0.33 seconds, and 3.3 µsec. With no input signal applied, period measurements return zero.

[4] The range and resolution are fixed for temperature measurements.

However, placing PT100_385 or PT100_392 into the range field will set the RTD type. Placing CUST1 into the range field will cause the Meter to use the values set into the R

and Alpha parameters.

[5] The range and resolution are fixed for diode test: 10 Vdc range and 5½

[6] The range and resolution are fixed for continuity tests: 1 kΩ range and

5½ digits.

[7] DC measurement voltage divided by dc reference voltage. For dc ratio,

Note

For best results in RATIO, the two input commons must be shorted at the Meter terminals. The analog filter (AFLTR) should be off.

Table 18. Preset Conditions for the MEASure? and CONFigure Commands

Parameter Setting

AC Filter (DET:BAND) 20 Hz

Autozero (ZERO:AUTO) OFF if NPLC <1, ON if NPLC >=1

DC Digital Filter ON

Input Impedance (INP:IMP:AUTO) OFF

Samples per trigger (SAMP:COUN) 1

Trigger count (TRIG:COUN) 1

Trigger delay (TRIG:DEL) Automatic

Trigger source (TRIG:SOUR) Internal (immediate)

Math Function (CALCulate subsystem) OFF

8845A/8846A

Programmers Manual

Setting Range and Resolution Parameters

The MEASure? and CONFigure commands incorporate parameters for setting the Meter’s function, its range, and its resolution. Placing the input signal’s expected amplitude into the range value causes the Meter to select a range appropriate for the supplied signal amplitude.

Although the frequency and period functions use a single range for all inputs between 3 Hz and 300 kHz, it is necessary to specify a range whenever specifing a resolution setting for these functions. When specifying resolution, specify it in the units of the function instead of number of digits. For ac or dc volts, specify the resolution in volts. The resolution specification for frequency is in hertz.

Using the READ? Command

READ?

Description READ? causes the Meter to take a measurement the next time the trigger

Note

A range parameter is required when specifying the resolution parameter.

condition is met after the READ? command is received. After the measurement is taken, the reading is placed in the output buffer. The READ? command will not cause readings to be stored in the Meter’s internal memory.

All measurements are sent to the output buffer until the buffer becomes full, at which point the Meter stops taking measurements. To keep the measurements running, measurements must be continually read out of the output buffer.

Always process the reading(s) from the output buffer after each READ? command. Failure to do so may cause some of the data from the previous READ? command to appear in the response for the last READ? command. For those times the buffer cannot be read after a READ? command, send a device clear (DC1) before issuing another READ? command.

Using the INITiate Command

Once the Meter has been configured for a measurement, the INITiate command causes the Meter to take a measurement when the trigger conditions have been met. The measurement reading(s) are placed in the Meter’s internal memory (up to 5,000 readings) to be read at a later time using the FETCh? command.

With one exception, the INITiate command stops the Meter from accepting any other remote commands until the Meter has completed both taking the measurement and storing the reading. The exception occurs when the trigger source is set to BUS with the TRIGger:SOURce command. Under this condition, the *TRG command or the IEEE-488 Group Execute Trigger will be processed to start the measurement.

Using the FETCh? Command

To process readings from the Meter’s internal memory to the output buffer, send the Meter a FETCh? command. With readings in the output buffer, a bus controller can then retrieve the readings over the bus.

Note

Digital Multimeter

Supported SCPI Commands

Using the SENSe Subsystem to Configure the Meter

Setting Meter functions and function parameters are controlled through the SENSe subsystem of commands. Both primary and secondary display functions are set using the FUNCtion commands. The parameters of each Meter function are also controlled through this subsystem of commands.

[SENSe]:FUNCtion[1/2] "<function>"

Description Sets the Meter to the measurement function listed in the function

parameter. The function must be enclosed in quotes in the command string (e.g. FUNC “VOLT:DC”).

[1]

Parameters [1/2]

= Use 1 for primary display, and 2 for secondary display

<function> = CAPacitance Capacitance CURRent:AC AC current CURRent:DC DC current VOLTage:AC AC voltage VOLTage:DC DC voltage VOLTage:DC:RATio DC voltage ratio

[3]

RESistance 2-wire resistance FRESistance 4-wire resistance FREQuency Frequency PERiod Period TEMPerature:RTD 2-wire temperature TEMPerature:FRTD 4-wire temperature DIODe Diode CONTinuity Continuity NONe

[2]

Turn off secondary display

Examples FUNC “VOLT:DC” Sets the Meter to volts dc

FUNC1 “VOLT:DC”; FUNC2 “VOLT:AC” Dual function command

Query FUNCtion[1/2]? Query measurement function

FUNC2? will return the measurement mode selected for the secondary display (assuming its been enabled using the FUNC2 command). FUNC1? or FUNC? will return the measurement mode for the primary display.

Notes [1] Using FUNC without a 1 or 2 will default to 1 for the primary display.

[2] Valid only when used with FUNC2.

[3] Valid only when used with FUNC or FUNC1.

[SENSe:]<function>

The SENSe subsystem allows configuring the Meter’s functions.

Parameters <function> = CAPacitance Capacitance

CURRent:AC AC current CURRent[:DC] DC current VOLTage:AC AC voltage VOLTage[:DC] DC voltage RESistance 2-wire resistance FRESistance 4-wire resistance FREQuency Frequency

Note

8845A/8846A

Programmers Manual

Notes [1] Valid only when used with FUNC2.

[SENSe:]<function>:RANGe(?) <n>

Description Sets the range according to the value supplied for n, of the Meter function

Parameters <n> = value of reading Expected reading in volts, amps or ohms

PERiod Period TEMPerature:RTD 2-wire temperature TEMPerature:FRTD 4-wire temperature DIODe Diode CONTinuity Continuity NONe

[1]

Turn off secondary display

specified in the variable <function>. Not having selectable ranges, an error is returned when using temperature, diode test, or continuity as the function with the RANGe command. This setting is stored in volatile memory

For the frequency and period functions, the range command value refers to the signal’s input voltage and not the range of the frequency or period measurement. Also, the word VOLTage must follow the function before the RANGe command. See examples below.

MINimum Lowest range MAXimum Highest range

Examples VOLT:RANG 10 Sets the Meter’s dc volts to the 10 volt range. CURR:AC:RANG 1e-3 Sets the Meter’s ac amps to the 100 mA range. RES:RANG 20e3 Sets the Meter’s ohms to the 100 kΩ range. FREQ:VOLT:RANG 5 Sets the voltage input range to the 10 volt range

for frequency measurements.

Query VOLT:RANG? Returns the set range for dc volts. VOLT:RANG? MIN Returns the minimum range of the dc volts

function. (1.00000000E-01 or 100 mV)

RES:RANG? MAX Returns the maximum range of the 2-wire

resistance function. (1.00000000E+09 or 1 GΩ)

[SENSe:]<function>:RANGe:AUTO(?) {OFF|ON}

Description Switches the Meter between autoranging and manual ranging. Not having

selectable ranges, an error is returned when the temperature, diode test, or continuity function is used with the RANGe:AUTO function. This setting is stored in volatile memory

For the frequency and period functions, the RANGe:AUTO command refers to the signal’s input voltage and not the range of the frequency or period measurement. Also, the word VOLTage must follow the function before the RANGe command. See examples below.

Note

Autorange thresholds are set for down range with readings <11 % of range and up range with readings >120 % of range.

Examples VOLT:RANG:AUTO ON Sets the Meter’s dc volts to autorange. CURR:AC:AUTO OFF Sets the Meter’s ac amps to manual ranging. FREQ:VOLT:RANG ON Sets the Meter’s voltage input to autorange

while making a frequency measurement.

Digital Multimeter

Supported SCPI Commands

Query VOLT:RANG:AUTO? Returns the dc volts autorange state. A zero

means off and a one means on.

[SENSe:]<function>:RESolution(?) <n>

Description Sets the resolution according to the value supplied for n, for the Meter

function specified in the variable <function>. Resolution is specified in the same units as the function. i.e., volts for the volts ac and dc functions. This setting is stored in volatile memory

For functions that do not have selectable ranges, an error is returned when using frequency, period, temperature, diode test, or continuity as the function in the RESolution command.

Parameters <n> = resolution value Desired resolution in volts, amps, ohms, or

farads. MIN Highest resolution MAX Lowest resolution

Examples VOLT:RES 1e-4 Sets the dc volts resolution to 100 μV. CURR:AC:RES 1e-8 Sets the ac amps resolution to 10 nA.

Query VOLT:RES? Returns the set resolution for dc volts. VOLT:RES? MIN Returns the minimum resolution of the dc volts

function.

[SENSe:]<function>:NPLCycles(?) <n>

Description Sets the Meter’s integration time for the function specified in <function>,

based on the number of power line cycles. This setting is stored in volatile memory

This command is only valid for dc voltage, dc current, temperature, and resistance (2-wire and 4-wire) functions.

Parameters <n> = 0.02 to 100 sets integration time to a preset value of a

power line cycle (0.02, 0.2, 1, 10, and 100) MIN 0.02 NPLC MAX 100 NPLC

Examples VOLT:DC:NPLC .2 Sets the dc volts integration time to 0.2 of a

power line cycle.

Query VOLT:NPLC? Returns the integration time for dc volts. CURR:NPLC? MIN Returns the minimum integration time for the dc

current function.

[SENSe:]TEMPerature:[TRANsducer:]<subfunction>:R0(?) <n>

Description Sets the resistance at zero degrees C specified by <n> for the R0 parameter

of the temperature function. This setting is stored in volatile memory.

Parameters <subfunction> = RTD 2-wire RTD FRTD 4-wire RTD

<n> = 0 to 1010 Resistance at 0 °C

Examples TEMP:RTD:R0 120 Sets the resistance at 0 °C to 120 ohms. Query TEMP:RTD:R0? Returns the set resistance at 0 °C.

8845A/8846A

Programmers Manual

[SENSe:]TEMPerature:[TRANsducer:]<subfunction>:TYPe(?) <n>

Description Sets the RTD type for the temperature function. This setting is stored in

Parameters <subfunction> = RTD 2-wire RTD

FRTD 4-wire RTD

<n> = PT100_385 Sets the RTD type to PT100 385 (R0 to

PT100_392 Sets the RTD type to PT100 392 (R0 to

CUST1 Sets the RTD type to be set by R0 and Alpha

Examples TEMP:RTD:TYP PT100_385 Sets the RTD type to PT100 385.

Query TEMP:RTD:TYP? Returns 385 or CUSTOM.

[SENSe:]TEMPerature:[TRANsducer:]<subfunction>:ALPHa(?) <n>

Description Sets the alpha variable for the temperature function. This setting is stored

volatile memory.

100Ω and Alpha to 0.00385055)

100Ω and Alpha to 0.00391600

settings.

in volatile memory.

Parameters <subfunction> = RTD 2-wire RTD FRTD 4-wire RTD

<n> = .00374 to .00393 Sets the alpha parameter

Examples TEMP:RTD:ALPH 0.00392 Sets the alpha parameter to 0.00392.

Query TEMP:RTD:ALPH? Returns the alpha setting of the temperature

[SENSe:]FREQuency:APERature(?) <n>

Description Sets the gate time for the frequency function to the value specified by <n>.

This setting is stored in volatile memory.

Parameters <n> = 0.01 Gate time of 10 ms (4½ digits)

0.1 (default) Gate time of 100 ms (5½ digits) 1 Gate time of 1 second (6½ digits) MIN Gate time of 10 ms (4½ digits) MAX Gate time of 1 second (6½ digits)

Examples FREQ:APER 0.1 Sets the frequency measurement gate time to 100

Query FREQ:APER? Returns the gate time for the frequency function.

[SENSe:]PERiod:APERature(?) <n>

Description Sets the gate time for the period function to the value specified by <n>.

This setting is stored in volatile memory.

function.

ms.

Parameters <n> = 0.01 Gate time of 10 ms (4½ digits)

0.1 (default) Gate time of 100 ms (5½ digits) 1 Gate time of 1 second (6½ digits) MIN Gate time of 10 ms (4½ digits) MAX Gate time of 1 second (6½ digits)

Digital Multimeter

Supported SCPI Commands

Examples PER:APER 0.1 Sets the period measurement gate time to 100

ms.

Query PER:APER? Returns the gate time for the period function.

[SENSe:]CURRent:AC:BANDwidth(?) <n>

Description Sets the appropriate filter for the frequency specified by <n>. This setting

is stored in volatile memory.

Parameters <n> = 3 Selects slow filter 20 (default) Selects medium filter 200 Selects fast filter MIN Selects slow filter MAX Selects fast filter

Examples CURR:AC:BAND 200 Sets the filter for ac current to fast.

Query CURR:AC:BAND? Returns the filter selection.

[SENSe:]VOLTage:AC:BANDwidth(?) <n>

Description Sets the appropriate filter for the frequency specified by <n>. This setting

is stored in volatile memory.

Parameters <n> = 3 Selects slow filter 20 (default) Selects medium filter 200 Selects fast filter MIN Selects slow filter MAX Selects fast filter

Examples VOLT:AC:BAND 20 Sets the filter for ac voltage to medium.

Query VOLT:AC:BAND? Returns the filter selection.

[SENSe:]DETector:BANDwidth(?) <n>

Description Sets the appropriate filter for the frequency specified by <n>. This setting

is stored in volatile memory and sets the filter for all functions that use an ac filter.

Parameters <n> = 3 Selects slow filter 20 Selects medium filter 200 Selects fast filter MIN Selects slow filter MAX Selects fast filter

Examples DET:BAND 20 Sets the filter to medium.

Query DET:BAND? Returns the filter selection.

DET:BAND? MAX Returns +2.00000000E+02 to indicate the fast

filter.

[SENSe:]FILTer[:DC][:STATe](?) <n>

Description Activates or deactivates the 3-pole analog filter to improve noise immunity

for dc functions. This setting is stored in volatile memory.

Parameters <n> = OFF or 0 Turns the analog dc filter off. ON or 1 Turns the analog dc filter on.

8845A/8846A

Programmers Manual

Examples FILT ON Turns the analog dc filter on.

Query FILT? Returns the analog dc filter setting.

[SENSe:]FILTer[:DC]:DIGital[:STATe](?) <n>

Description Activates or deactivates the digital averaging filter to improve noise

Parameters <n> = OFF or 0 Turns the digital averaging filter off.

ON or 1 Turns the digital averaging filter on.

Examples FILT:DIG ON Turns the digital averaging filter on.

Query FILT:DIG? Returns the digital averaging filter setting. (0 =

Note

Since the corner frequency of the analog filter is about 8 Hz, the filter does not add much rejection until frequencies are significantly higher than that.

immunity for dc functions. This setting is stored in volatile memory.

OFF and 1 = ON)

[SENSe:]VOLTage[:DC]:FILTer[:STATe](?) <n>

Description Activates or deactivates the 3-pole analog filter to improve noise immunity

for dc voltage functions. This setting is stored in volatile memory.

Parameters <n> = OFF or 0 Turns the analog dc voltage filter off. ON or 1 Turns the analog dc voltage filter on.

Examples VOLT:FILT ON Turns the analog dc voltage filter on.

Query VOLT:FILT? Returns the analog dc voltage filter setting.

[SENSe:]VOLTage[:DC]:FILTer:DIGital[:STATe](?) <n>

Description Activates or deactivates the digital averaging filter to improve noise

immunity for dc voltage functions. This setting is stored in volatile memory.

Parameters <n> = OFF or 0 Turns the digital averaging filter off. ON or 1 Turns the digital averaging filter on.

Examples VOLT:FILT:DIG ON Turns the digital averaging filter on.

Query VOLT:FILT:DIG? Returns the digital averaging filter setting. (0 =

OFF and 1 = ON)

[SENSe:]CURRent[:DC]:FILTer[:STATe](?) <n>

Description Activates or deactivates the 3-pole analog filter to improve noise immunity

for dc current functions. This setting is stored in volatile memory.

Parameters <n> = OFF or 0 Turns the analog dc current filter off. ON or 1 Turns the analog dc current filter on.

Examples CURR:FILT ON Turns the analog dc current filter on..

Query CURR:FILT? Returns the analog dc current filter setting. (0 =

OFF and 1 = ON)

Digital Multimeter

Supported SCPI Commands

[SENSe:]CURRent[:DC]:FILTer:DIGital[:STATe](?) <n>

Description Activates or deactivates the digital averaging filter to improve noise

immunity for dc current functions. This setting is stored in volatile memory.

Parameters <n> = OFF or 0 Turns the digital averaging filter off. ON or 1 Turns the digital averaging filter on.

Examples CURR:FILT:DIG ON Turns the digital averaging filter on.

Query CURR:FILT:DIG? Returns the digital averaging filter setting. (0 =

OFF and 1 = ON)

[SENSe:]RESistance[:DC]:FILTer[:STATe](?) <n>

Description Activates or deactivates the 3-pole analog filter to improve noise immunity

for the 2-wire resistance function. This setting is stored in volatile memory.

Parameters <n> = OFF or 0 Turns the analog 2-wire resistance filter off. ON or 1 Turns the analog 2-wire resistance filter on.

Examples RES:FILT ON Turns the analog 2-wire resistance filter on.

Query RES:FILT? Returns the analog 2-wire resistance filter

setting. (0 = OFF and 1 = ON)

[SENSe:]RESistance[:DC]:FILTer:DIGital[:STATe](?) <n>

Description Activates or deactivates the digital averaging filter to improve noise

immunity the 2-wire resistance dc function. This setting is stored in volatile memory.

Parameters <n> = OFF or 0 Turns the digital averaging filter off. ON or 1 Turns the digital averaging filter on.

Examples RES:FILT:DIG ON Turns the digital averaging filter on.

Query RES:FILT:DIG? Returns the digital averaging filter setting. (0 =

OFF and 1 = ON)

[SENSe:]FRESistance[:DC]:FILTer[:STATe](?) <n>

Description Activates or deactivates the 3-pole analog filter to improve noise immunity

for the 4-wire resistance function. This setting is stored in volatile memory.

Parameters <n> = OFF or 0 Turns the analog 4-wire resistance filter off. ON or 1 Turns the analog 4-wire resistance filter on.

Examples FRES:FILT ON Turns the analog 4-wire resistance filter on.

Query FRES:FILT? Returns the analog 4-wire resistance filter

setting. (0 = OFF and 1 = ON)

8845A/8846A

Programmers Manual

[SENSe:]FRESistance[:DC]:FILTer:DIGital[:STATe](?) <n>

Description Activates or deactivates the digital averaging filter to improve noise

Parameters <n> = OFF or 0 Turns the digital averaging filter off.

ON or 1 Turns the digital averaging filter on.

Examples FRES:FILT:DIG ON Turns the digital averaging filter on.

Query FRES:FILT:DIG? Returns the digital averaging filter setting. (0 =

[SENSe:]UNIT:TEMPerature(?) <units>

Description Sets the temperature units for the temperature function. This setting is

Parameters <units> = Cel Sets temperature units to Celsius

Far Sets temperature units to Fahrenheit

Examples UNIT:TEMP C Sets temperature units to Celsius.

immunity for the 4-wire resistance function. This setting is stored in volatile memory.

OFF and 1 = ON)

stored in volatile memory.

Kel Sets temperature units to Kelvin

Query UNIT:TEMP? Returns the temperature units setting. (C =

Celsius, F = Fahrenheit, and K = Kelvin)

[SENSe:]ZERO:AUTO <n>

Description Activates (default) or deactivates the autozero mode. This setting is stored

in volatile memory.

Parameters <n> = OFF Turns Autozero mode off. ON Turns autozero mode on. ONCE Initiates a zero measurement immediately.

Examples ZERO:AUTO ON Turns autozero mode on.

Query ZERO:AUTO? Returns the state of the autozero mode. (0 = OFF

and 1 = ON)

[SENSe:]VOLTage[:DC]:IMPedance:AUTO(?) <n>

Description Activates or deactivates (default) the automatic input impedance mode for

dc voltage measurements. With AUTO OFF, the input impedance is fixed at 10 MΩ for all ranges. With AUTO ON, the input impedance is set to >10 GΩ for the 100 mV, 1 V, and 10 V ranges. This setting is stored in volatile memory.

Parameters <n> = OFF or 0 Turns off automatic input impedance. ON or 1 Turns on automatic input impedance.

Examples VOLT:IMP:AUTO ON Turns on automatic input impedance.

Query VOLT:IMP:AUTO? Returns the state of the input impedance mode.

(0 = OFF and 1 = ON)

Digital Multimeter

Supported SCPI Commands

INPut:IMPedance:AUTO(?) <n>

Description Activates or deactivates (default) the automatic input impedance mode for

Parameters <n> = OFF or 0 Turns off automatic input impedance. ON or 1 Turns on automatic input impedance.

Examples IMP:AUTO ON Turns on automatic input impedance.

Query IMP:AUTO? Returns the state of the input impedance mode.

(0 = OFF and 1 = ON)

ROUTe:TERMinals?

Description A query that returns the state of the front or rear panel input terminals

switch.

Examples ROUT:TERM? Returns “FRON” or “REAR”.

Programming for Math Operations

Of the five possible Meter math functions, only one can be enabled at a time. Once a math function is selected, it stays selected until the Meter is powered down, or another math function is set. A reset command received through the remote interface will also disable the math function. Presetting some math registers are possible.

Table 19 is a matrix indicating which math functions work with each Meter function. Selecting a math function that is not allowed with a Meter function causes math to be disabled. Selecting a math function that is not allowed after selecting an allowed math function will result in a “Setting Conflict” error.

Note

Math must be enabled before writing to the zero (null) or dB measurement registers.

Table 19. Allowed Math/Measurement Function Combinations

DCV ACV DCI ACI 2W 4W Freq Period Cont Diode Temp Cap

Null Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes

Average Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes

dB No Yes No No No No No No No No No No

dBm No Yes No No No No No No No No No No

Limit Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes

8845A/8846A

Programmers Manual

CALCulate:FUNCtion(?) {NULL|DB|DBM|AVERage|LIMit}

Description Selects one of five math functions. This setting is stored in volatile

Parameters <n> = NULL Uses the present reading as an offset to zero

DB Selects the DB mode. DBM Selects the dBm mode. AVERage Selects the average mode LIMit Selects the Limit Testing mode.

Examples CALC:FUNC DBM Selects the dBm mode.

Query CALC:FUNC? Returns the selected math function.

CALCulate:STATe(?) <n>

Description Activates or deactivates the math function selected with CALC:FUNC

Parameters <n> = ON or 1 Activates the math function set previously by

OFF or 0 Deactivates the math function.

memory. Selecting a math function disables any math function which may have been set previously. For the selected math function to take effect, the CALCulate:STATe must be ON.

the returned reading.

command. This setting is stored in volatile memory.

CALC:FUNC command.

Examples CALC:STAT ON Turns on the math function.

Query CALC:STAT? Returns the state of the math function. (0 = OFF

CALCulate:AVERage:MINimum?

Description Retrieves the minimum value measured during a statistics operation. This

value is cleared whenever the Meter is powered off then back on, a statistics function is enabled, or the Meter receives a reset through the remote interface. This setting is stored in volatile memory.

Query CALC:AVER:MIN? Returns the minimum value of the statistics operation.

CALCulate:AVERage:MAXimum?

Description Retrieves the maximum value measured during a statistics operation. This

Query CALC:AVER:MAX? Returns the maximum value of the statistics operation.

CALCulate:AVERage:AVERage?

Description Retrieves the average value measured during a statistics operation. This

and 1 = ON)

Query CALC:AVER:AVER? Returns the average value of the statistics operation.

Digital Multimeter

Supported SCPI Commands

CALCulate:AVERage:COUNt?

Description Retrieves the number of measurements taken during a statistics operation.

This value is cleared whenever the Meter is powered off then back on, a statistics function is enabled, or the Meter receives a reset through the remote interface. This setting is stored in volatile memory.

Query CALC:AVER:COUN? Returns the count value of the statistics operation.

CALCulate:NULL:OFFSet(?) {<value>|MINimum|MAXimum}

Description Sets the offset value used for the zero function. Math operation must be

enabled to write to the zero offset register. This setting is stored in volatile memory.

Parameters <value> = 0 to 120 % of highest range. MINimum Sets offset register to -120 % of highest

range of selected function. MAXimum Sets offset register to 120 % of highest range

of selected function.

Examples CALC: NULL:OFFS 100 Sets zero offset register to 100.

Query CALC:NULL:OFFS? Returns the zero offset register value.

CALCulate:DB:REFerence(?) {<value >|MINimum|MAXimum}

Description Sets the relative value used for the dB function. Math operation must be

enabled to write to the dB relative register. This setting is stored in volatile memory.

Parameters <value> = 0 to ±200 dBm. MINimum Sets dB relative register to -200 dBm.

MAXimum Sets dB relative register to 200 dBm.

Examples CALC:DB:REF 25 Sets dB relative register to 25 dBm.

Query CALC:DB:REF? Retrieves the dB relative register value.

CALCulate:DBM:REFerence(?) {<value>|MINimum|MAXimum}

Description Sets the reference impedance for the dBm function. Math operation must

be enabled to write to the dBm reference impedance register. This setting is stored in volatile memory.

Parameters <value> = 2, 4, 6, 16, 50, 75, 90, 93, 100, 110, 124, 125, 135, 150, 250,

300, 500, 600 (default), 800, 900, 1000, 1200, or 8000 Ω.

MINimum Sets dBm reference impedance register to

50 Ω. MAXimum Sets dBm reference impedance register to

8000 Ω.

Examples CALC:DBM:REF 110 Sets dBm reference impedance register to

110 Ω.

Query CALC:DBM:REF? Retrieves the present dBm reference impedance

8845A/8846A

Programmers Manual

CALCulate:LIMit:LOWer(?) {<value >|MINimum|MAXimum}

Description Sets the lower limit value used for limit testing. This setting is stored in

Parameters <value> = 0 to 120 % of highest range. MINimum Sets lower limit register to -120 % of highest

MAXimum Sets lower limit register to 120 % of highest

Examples CALC:LIM:LOW 235 Sets lower limit register to 235.

Query CALC: LIM:LOW? Retrieves the lower limit register value.

CALC:LIM:LOW? MIN Returns -120 % of highest range of selected

CALC:LIM:LOW? MAX Returns 120 % of highest range of selected

CALCulate:LIMit:UPPer {<value >|MINimum|MAXimum}

Description Sets the upper limit value used for limit testing. This setting is stored in

volatile memory.

range of selected function.

function.

volatile memory.

Parameters <value> = 0 to 120 % of highest range. MINimum Sets upper limit register to -120 % of highest

MAXimum Sets upper limit register to 120 % of highest

Examples CALC:LIM:UPP -150 Sets upper limit register to -150.

Query CALC:LIM:UPP? Retrieves the upper limit register value.

CALC:LIM:UPP? MIN Returns -120 % of highest range of selected

CALC:LIM:UPP? MAX Returns 120 % of highest range of selected

DATA:FEED RDG_STORE, <n>

Description Enables (default) or disables storing measurements in the Meter’s internal

memory when an INITiate command is executed. When enabled, 5,000 measurements are stored in the Meter’s internal memory when executing an INITiate command.

Note The MEASure? and CONFigure commands automatically

enable the storing of measurements.

Disabling the storage of readings may be beneficial when performing statistics operations. Minimum, maximum, and average values can be calculated without storing each measurement.

range of selected function.

function.

Note While readings are disabled, attempting to transfer readings to

the output buffer with a FETCh? command will generate an error.

Digital Multimeter

Supported SCPI Commands

Parameters <n> = “CALCulate” Enable the storing of measurements. “” Disable the storage of measurements.

Example DATA:FEED RDG_STORE, “CALC”.

DATA:FEED?

Description Retrieves the state of the reading store setting.

Query DATA:FEED? Returns CALC or “”.

CALCulate:KMATh:MMFactor(?) <value>

Description Sets the value in the “m” register for the mx+b calculation. Parameters <value> = 0 to ±999.999999

Examples CALC:KMAT:MMF 37 Sets “m” register to 37.

Query CALC: KMAT:MMF? Retrieves the “m” register value.

CALCulate:KMATh:MBFactor(?) <value>

Description Sets the value in the “b” register for the mx+b calculation. Parameters <value> = 0 to ±999.999999

Examples CALC:KMAT:MBF 37 Sets “b” register to 37.

Query CALC: KMAT:MBF? Retrieves the “b” register value.

CALCulate:KMATh:MUNits(?) <name> = 3 characters using ‘A’ through ‘Z’

Description Sets the units for the mx+b calculation.

Parameters <name> = A to ZZZ Up to three letters

Examples CALC:KMAT:MUN VOL Sets units to “VOL”.

Query CALC: KMAT:MUN? Retrieves the set units value.

CALCulate:KMATh:STATe(?) <n>

Description Enables or disables the mx+b calculation.

Parameters <n> = ON or 1 Enables mx+b calculations.

OFF or 0 Disable mx+b calculations

Examples CALC:KMAT:STAT ON Enables mx+b calculations.

Query CALC: KMAT:STAT? Retrieves the state of the mx+b calculation (0 =

OFF, 1 = ON).

Programming the Trigger System

The Meter is designed to provide extensive control over the triggering of a single measurement or series of measurements. One trigger can cause the Meter to take a single measurement or multiple measurements; up to 50,000 per trigger.

Operating the Meter remotely requires selecting one of three trigger methods: internal, external, or bus triggering. Once a source is selected, the Meter must be in a “wait-fortrigger” state before the trigger will start a measurement cycle.

Figure 4 shows the multimeter’s triggering system.

8845A/8846A

Programmers Manual

Initiate Triggering

MEASure? READ? INITiate

Trigger Source

TRIGger:SOURce IMMediate TRIGger:SOURce EXTernal TRIGger:SOURce BUS Front-panel "Single" key

Triggering Delay

TRIGger:DELay

Sample (*) Annuniator

Idle

State

Wait-for-

Trigger

State

Delay

Measurement

Sample

Sample Count # 1

Trigger Count # 1

dae02.eps

Figure 4. 884XA Triggering System

The Meter can be put into a wait-for-trigger state remotely by sending it a MEASure?, READ?, or INITiate command. Once received by the Meter, it takes approximately 20

ms to setup the Meter and put it in to the wait-for-trigger state. Any triggers received during this set-up time are ignored.

Using the Triggering Commands

INITiate

Description Sets the Meter to the wait-for-trigger state in which the next trigger from

the selected source triggers a measurement cycle. Up to 5,000 measurements are placed into the Meter’s internal memory, where they can be retrieved with the FETCh? command.

Examples INIT Sets the Meter to the wait-for-trigger state.

READ?

Description Sets the Meter in to the wait-for-trigger state where the next trigger from

the selected source triggers a measurement cycle. Measurements are sent directly to the output buffer.

Examples READ? Sets the Meter to the wait-for-trigger state.

Digital Multimeter

Supported SCPI Commands

TRIGger:SOURce(?) {BUS|IMMediate|EXTernal}

Description Sets the source from which the Meter will expect a measurement trigger.

Parameters <n> = BUS Sets the Meter to expect a trigger through the

IEEE-488 bus or upon execution of a *TRG

command. IMMediate Selects Meter’s internal triggering system. EXTernal Sets the Meter to sense triggers through the

trigger jack on the rear panel of the Meter.

Examples TRIG:SOUR BUS Sets the Meter to expect a trigger through the

IEEE-488 bus or upon execution of a *TRG command.

Query TRIG:SOUR? Retrieves the trigger source for which the Meter

has been set (BUS, IMM, or EXT).

TRIGger:DELay <n>

Description Sets the delay between receiving a trigger and the beginning of

measurement cycle.

Parameters <n> = 0 to 3600 Delay specified in seconds. MINimum Delay set to 0 seconds. MAXimum Delay set to 3600 seconds.

Examples TRIG:DEL 14 Sets the trigger delay to 14 seconds.

Query TRIG:DEL? Retrieves the amount of time set for a trigger

delay. TRIG:DEL? MIN Returns 0 seconds TRIG:DEL? MAX Returns 3600 seconds

TRIGger:DELay:AUTO <n>

Description Enables or disables automatic trigger delay. The amount of delay is set

based on selected function, integration time, and filter setting. When a specific trigger delay is set using the TRIG:DELAY <n> command, automatic trigger delay is disabled. This setting is stored in volatile memory.

Parameters <n> = ON or 1 Automatic trigger delay is enabled. OFF or 0 Automatic trigger delay is disabled.

Examples TRIG:DEL:AUTO ON Enables automatic trigger delay

Query TRIG:DEL:AUTO? Retrieves the state of the automatic trigger delay

( 0 = OFF, 1 = ON).

SAMPle:COUNt {<value>|MINimum|MAXimum}

Description Sets the number of measurements the Meter takes per trigger. This setting

is stored in volatile memory.

Parameters <n> = 0 to 50,000 Number of measurements per trigger MINimum Number of measurements per trigger set to 1. MAXimum Number of measurements per trigger set to

50,000.

Examples SAMP:COUN 2450 Number of measurements per trigger set to

2,450.

8845A/8846A

Programmers Manual

Query SAMP:COUN? Retrieves the number of samples per trigger

SAMP:COUN? MIN Returns 1 to indicate the minimum number of

SAMP:COUN? MAX Returns 50,000 to indicate the maximum number

TRIGger:COUNt <n>

Description Sets the number of triggers the Meter will take before switching to an idle

Parameters <n> = 0 to 50,000 Number of triggers before Meter becomes

MINimum Number of triggers is set to 1. MAXimum Number of triggers is set to 50,000. INFinite Continuously accepts triggers. A device clear

Examples TRIG:COUN 430 Number of triggers set to 430.

presently set in the Meter.

samples the Meter will accept per trigger.

of measurements the Meter will accept per

trigger.

state. This setting is stored in volatile memory.

idle.

is required to set the Meter to idle state after INFinite has been set.

Query TRIG:COUN? Retrieves the number of triggers presently set in

TRIG:COUN? MIN Returns 1 to indicate the minimum number of

TRIG:COUN? MAX Returns 50,000 to indicate the maximum number

Using System-Related Commands

FETCh[1/2]?

Description Moves measurements stored in the Meter’s internal memory to the output

buffer. FETCh1? or FETCh? returns measurements from the primary display. FETCh2? Returns readings from the secondary display.

Example FETCh2? Retrieves a single measurement from the Meter’s

FETCh3?

Description Retrieves the last measurement from the Meter's primary display. Unlike

the FETCh? or FETCh1? commands which require that the meter be first placed in the "wait for trigger" state using the INIT command to trigger a measurement or multiple measurements from the primary display, FETCh3? will return a single measurement from the primary display if there is one. If a measurement isn't available, the command is ignored.

the Meter. Returns 9.90000000E+37 if trigger

count has been set to INFinite.

triggers the Meter will accept per trigger.

of triggers the Meter will accept per trigger.

internal memory that was taken by the secondary

display if the secondary measurements are

enabled.

Examples FETCh3? Retrieves the last measurement from the primary

display of the Meter.

Digital Multimeter

Supported SCPI Commands

DISPlay <n>

Description Enables or disables the Meter’s display. This setting is stored in volatile

memory.

Parameters <n> = ON or 1 Enables the display. OFF or 0 Disables the display.

Examples DISP ON Enables the Meter’s display.

Query DISP? Retrieves the state of the display ( 0 = OFF and 1

= ON).

DISPlay:TEXT(?) <quoted string >

Description Displays a message on the Meter’s display. This setting is stored in volatile

memory.

Note

The Meter must be remote before executing this command.

Parameters <quoted string> = Up to 12 characters. Additional characters are

truncated.

Examples DISP:TEXT “Hello” Hello is displayed in the Meter’s display.

Query DISP:TEXT? Retrieves the text sent to the Meter in a

DISPlay:TEXT:CLEar

Description Clears the displayed message on the Meter’s display.

Examples DISP:TEXT:CLE Meter’s display message is cleared.

SYSTem:BEEPer

Description Causes the Meter to beep once.

Examples SYST:BEEP Meter beeps.

SYSTem:BEEPer:STATe? <n>

Description Enables or disables the Meter’s beeper. This setting is stored in volatile

memory. Disabling the beeper causes the Meter to not beep for the following conditions:

a new minimum or maximum is detected during statistics a limit is exceeded during a limits test a forward-biased diode is measured during a diode test

Parameters <n> = ON or 1 Enables the Meter’s beeper. OFF or 0 Disables the Meter’s beeper.

DISP:TEXT command.

Examples SYST:BEEP:STAT ON Enables the beeper.

Query SYST:BEEP:STAT? Retrieves the state of the Meter’s beeper ( 0 =

OFF and 1 = ON).

SYSTem:DATE(?) <date>

Description Sets the system clock date.

8845A/8846A

Programmers Manual

Parameters <date> = MM/DD/YYYY or MM-DD-YYYY. MM between 1 and 12 DD between 1 and 31 YYYY between 1970 and 2038

Examples SYST:DATE 10/25/2007

Query SYST:DATE? Returns the Meter’s system clock date.

SYSTem:TIME(?) <time>

Description Sets the system clock time in 24 format.

Parameters <time> = HH:MM:SS or HH-MM-SS

HH between 0 and 23 MM between 0 and 59 SS between 0 and 59

Examples SYST:TIME 14:25:10 Sets time to 2:25:10 PM

Query SYST:TIME? Returns the Meter’s system clock time.

SYSTem:VERSion?

Description Retrieves the Meter’s present SCPI command version.

Examples SYST:VERS? Returns the SCPI version.

DATA:POINts?

Description Retrieves the number of measurements contained in the Meter’s internal

memory.

Examples DATA:POIN? Returns number of measurements in internal

*RST

Description Resets the Meter to its power-up configuration.

Examples *RST Resets the Meter.

IDN <n>, [<quoted string>]

Description Enables or disables the retrieval of a user-specified IDN string or factory-

set IDN string with the *IDN? command. Also sets the user defined IDN string.

Parameters <n> = ON or 1 Enables user-defined string. OFF or 0 Disables user-defined string and causes the

<quoted string> = Up to a 35 character string.

memory.

factory IDN string to be returned for an *IDN?

command.

Example IDN ON, “My Meter” Sets the IDN string to “My Meter” and enables

the user defined string to be returned when the

*IDN? command is received by the Meter.

Digital Multimeter

Supported SCPI Commands

*IDN?

Description Returns the IDN string. If IDN is enabled (ON), then the Meter returns the

user defined string. If IDN is disabled (OFF), the the Meter returns the IDN string set at the factory.

Query *IDN? Returns up to 35 character string.

Using Status Reporting Commands

SYSTem:ERRor?

Description Retrieves an error from the Meter’s error queue. Errors are retrieved in

first-in, first-out (FIFO) order. Each error may contain up to 80 characters. The error queue will store up to 16 errors at which point no additional errors will be stored until errors are removed from the queue.

Examples SYST:ERR? Returns the next error in the error queue.

Performing a SYST:ERR? command when the

error queue is empty causes +0,″No error″ to be

returned.

SYSTem:ERRor:BEEPer(?) <n>

Description Enable or disables the Meter’s beeper for error messages. This setting is

stored in volatile memory.

Parameters <n> = ON or 1 Enables beeper for error messages. OFF or 0 Disables beeper for error messages.

Examples SYST:ERR:BEEP ON Set Meter to beep when errors are detected.

Query SYST:ERR:BEEP? Returns state of beeper for error messages ( 0 =

STATus:QUEStionable:ENABle(?) <n>

Description Enables or disables bits in the Meter’s Questionable Data enable register.

Parameters <n> = 0 to 65535 Binary-weighted decimal value representing the

Examples STAT:QUES:ENAB 4 Sets bit 2 to one and all others to zero.

Query STAT:QUES:ENAB? Retrieves a binary-weighted decimal value

STATus:QUEStionable:EVENt?

Description Enables or disables bits in the Meter’s Questionable Data event register.

OFF and 1 = ON).

bits to set in the register. Although a 16-bit

65535, only bits 0, 1, 9, 11, 12, and 13 are used.

representing the bits set in the questionable data

enable register.

Parameters <n> = 0 to 65535 Binary-weighted decimal value representing the

bits to set in the register. Although a 16-bit

65535, only bits 0, 1, 9, 11, 12, and 13 are used.

Query STAT:QUES:EVEN? Retrieves a binary-weighted decimal value

representing the bits set in the questionable data

event register.

8845A/8846A

Programmers Manual

STATus:PRESet

Description Sets all bits to zero in the Meter’s Questionable Data enable register.

Examples STAT:PRES Sets all bits to zero.

*CLS

Description Sets all bits to zero in the Meter’s status byte register and all event

Examples *CLS Sets all bits to zero and clear error queue.

*ESE <enable value>

Description Enables or disables bits in the Meter’s Standard Event enable register.

Parameters <n> = 0 to 255 Binary-weighted decimal value representing the

Examples *ESE 160 Sets bits 5 and 7 to one and all other bits to zero.

registers. Also clears the error queue.

bits to set in the register. Although this register

has 8 bits and will accept a number from 0 to

255, only bits 0, 2 through 5, and 7 are used.

*ESE?

*ESR?

*OPC

*OPC?

Description Retrieves the value in the Meter’s Standard Event enable register.

Examples *ESE? Retrieves a binary-weighted decimal value

representing the bits set in the Standard Event

enable register.

Description Retrieves the value in the Meter’s Standard Event register.

Examples *ESR? Retrieves a binary-weighted decimal value

representing the bits set in the Standard Event

Description Sets bit 0 (Operation complete) in the Meter’s Standard Event register.

Examples *OPC Sets bit 0 in the Standard Event register.

Description Returns a one to the Meter’s output buffer.

Examples *OPC? A “1” is placed in the output buffer of the Meter.

*PSC <n>

Description Enables or disables the clearing of the Status Byte Enable register and

Standard Event Enable register when Meter power is turned on. This setting is stored in non-volatile memory.

Parameters <n> = 0 Disables clearing Status Byte and Standard

Event Enable register at power-up. 1 Enables clearing Status Byte and Standard Event

Enable register at power-up.

Digital Multimeter

Supported SCPI Commands

*PSC?

Description Returns the state of the clearing of the Status Byte and Standard Event

Enable registers at power-up.

Examples *PSC? Returns zero if clearing is disabled. Returns one

if clearing is enabled.

*SRE <enable value>

Description Enables or disables bits in the Meter’s Status Byte enable register.

Parameters <n> = 0 to 255 Binary-weighted decimal value representing the

bits to set in the register. Although this register

has 8 bits and will accept a number from 0 to

255, only bits 3 through 5 are used.

Examples *SRE 48 Sets bits 4 and 5 to one and all other bits to zero.

*SRE?

Description Retrieves the value in the Meter’s Status Byte enable register.

Examples *SRE? Retrieves a binary-weighted decimal value

representing the bits set in the enable register.

*STB?

Description Retrieves the value in the Meter’s Status Byte summary register. Although

like a serial poll, this command is processed as an instrument command. Returned results are the same as when receiving a serial poll, but the SRQ bit is not cleared if a serial poll has occurred.

Examples *STB?

Calibration Commands

CALibration? [{ON|OFF}]

Description After entering the proper code using the CAL:SEC:CODE command, this

command causes the Meter to perform an adjustment using the values supplied with the CAL:VAL command. See the 8845A/8846A Service Manual for details on using this command.

Parameters <n> = ON or 1 Execute only one calibration step. OFF or 0 Execute a group (mode) of related calibration

Examples CAL? ON Execute one calibration step for the calibration

CAL? Returns +0 (good) or +1 (failed)

steps at one time.

group specified by the CAL:VAL command.

8845A/8846A

Programmers Manual

CALibration:COUNt?

Description Retrieves the number of times Meter points have been calibrated. Read this

Examples CAL:COUN? Retrieves the number of times points have been

CALibration:RECord

Description Stores the calibration values.

Example CAL:REC Stores all of the Meter’s changed calibration

value just after receiving the Meter to obtain a starting value. This setting is stored in non-volatile memory.

Note

This value increments once for each calibration point. A complete calibration will increment this value many times. The maximum count is 4,294,967,295, at which point the next calibration causes this value to reset to zero.

calibrated.

values.

CALibration:SECure:CODE <new code >

Description Sets a new calibration password. Before entering a new code, you must

first enter the old password using the CAL:SEC:STAT command. The Meter has a password of FLUKE884X when shipped from the factory.

Parameters <new code> = Up to 12 characters of capital letters and

Example CAL:SEC:CODE 12B Sets the new calibration password to 12B.

The password cannot be recalled, but the password can be reset to the factory default without returning the Meter for service.

XW Warning

To avoid electric shock and or injury, do not open the Meter unless you are qualified to do so.

Follow the instructions in the 8845A/8846A Service Manual for opening the Meter case. Located at the rear of the chassis, behind the Ethernet connector (J17), there is a jumper connector labeled W2. Short the pins of W2 together and power cycle the Meter to reset the password to FLUKE884X.

CALibration:SECure:STATe(?) <n>,<code >

Description Secure or unsecure the Meter for calibration. This setting is stored in non-

volatile memory.

numerials (A-Z, 0-9).

Parameters <n> = ON or 1 Secures the Meter from calibration. OFF or 0 Unsecures the Meter for calibration.

<code> = Up to 12 character string.

Example CAL:SEC:STAT OFF 12B Unsecures the Meter for calibration when the

password is 12B.

Query CAL:SEC:STAT? Retrieves the state of the Meter’s calibration

security ( 0 = OFF and 1 = ON).

Digital Multimeter

Supported SCPI Commands

CALibration:STRing(?) <quoted string>

Description Store calibration information in the Meter’s memory. This setting is stored

in non-volatile memory.

Parameters <quoted string> = Up to a 40 character string.

Query CAL:STR? Retrieves the Meter’s calibration string.

CALibration:DATE(?) <date>

Description Sets the calibration date on the 8845A only since it does not have a real-

time clock.

Parameters <date> = MM/DD/YYYY or MM-DD-YYYY. MM between 1 and 12 DD between 1 and 31 YYYY between 1970 and 2038

Examples CAL:DATE 10/25/2007

Query CAL:DATE? Returns the Meter’s calibration date.

CALibration:VALue(?) <mode>, <value >

Description Sets up the Meter for a calibration point. The mode parameter is the name

of the functional group being calibrated. The value parameter is the Meter’s range for the calibration point. Refer to the calibration procedure in the 8845A/8846A Service Manual for mode names and values.

Parameters <mode> = See 8845A/8846A Service Manual <value> = See 8845A/8846A Service Manual

Query CAL:VAL? Retrieves the Meter’s calibration value.

CALibration:STEP(?) <step #> [,Reference]

Description Specifies the calibration step number and the optional reference value of

the known calibration signal used by the calibration procedure. See the 8845A/8846A Service Manual for a list of calibration steps with values.

Parameters <step #> = (See the 8845A/8846A Service Manual)

Examples CAL:STEP 5 Sets the calibration step to number 5.

Query CAL:STEP? Returns the Meter’s calibration step.

Using RS-232/Ethernet Interface Commands

There are four remote commands that are specifically applicable to controlling the Meter using the RS-232 or Ethernet remote interface.

SYSTem:LOCal

Description Places the Meter in the local mode. Front-panel keys still function.

Example SYST:LOC

8845A/8846A

Programmers Manual

SYSTem:REMote

Description Places the Meter in the remote mode for RS-232 or Ethernet remote

Example SYST:REM

SYSTem:RWLock

Description Like the SYST:REM command, this command places the Meter into

Example SYST:RWL

Ctrl-C

Description Immediately stops transfers of data over the RS-232 interface and clears

control. All front-panel keys, except the local key, are disabled.

Note

To avoid unpredictable operation, send a SYS:REM command to the Meter before sending or receiving data over the RS-232 or Ethernet interface.

remote mode, but with all front-panel keys, including the local key, disabled.

any output data.

This the same as sending a device clear over the IEEE-488 bus.

Command Terminators

A command string sent to the Meter must terminate with a <new line> character. The IEEE-488 EOI (end-or-identify) message is interpreted as a <new line> character and can be used to terminate a command string in place of a <new line> character. A <carriage return> followed by a <new line> is also accepted. Command string termination will always reset the current SCPI command path to the root level.

SCPI Parameter Types

The SCPI language defines several different data formats to be used in program messages and response messages.

Numeric Parameters

Commands that require numeric parameters will accept all commonly used decimal representations of numbers including optional signs, decimal points, and scientific notation. Special values for numeric parameters like MINimum, MAXimum, and DEFault are also accepted. You can also send engineering unit suffixes with numeric parameters (e.g., M, K, or u). If only specific numeric values are accepted, the Meter will automatically round the input numeric parameters. The following command uses a numeric parameter:

Note

VOLTage:DC:RANGe {<range>|MINimum|MAXimum}

Digital Multimeter

Supported SCPI Commands

Discrete Parameters

Discrete parameters are used to program settings that have a limited number of values (like BUS, IMMediate, EXTernal). They have a short form and a long form just like command keywords. You can mix upper- and lower-case letters. Query responses will always return the short form in all upper-case letters. The following command uses discrete parameters:

TRIGger:SOURce {BUS|IMMediate|EXTernal}

Boolean Parameters

Boolean parameters represent a single binary condition that is either true or false. For a false condition, the Meter will accept OFF or 0. For a true condition, the Meter will accept ON or 1. When you query a boolean setting, the instrument will always return “0” or “1”. The following command uses a boolean parameter:

INPut:IMPedance:AUTO {OFF|ON}

String Parameters

String parameters can contain virtually any set of ASCII characters. A string must begin and end with matching quotes; either with a single quote or with a double quote. You can include the quote delimiter as part of the string by typing it twice without any characters in between. The following command uses a string parameter:

DISPlay:TEXT <quoted string>

Alternate Programming Language Compatibility

The Meter can be configured to accept and execute 8845A/46A SCPI commands (HP 34401A compatible), non SCPI compliant modes Fluke 8842A or Fluke 45 multimeter commands. Remote operation will only allow you to access the functionality of the multimeter language selected. Full Meter capability is available through the 8845A/46A SCPI programming language. For more information on selecting the alternate languages from the front panel menu, see Selecting the Programming Language earlier in this manual. From the remote interface, use the following commands to select the alternate languages:

L1 selects SCPI language L2 selects Fluke 45A language L3 selects Fluke 8842A language

The Meter implements virtually all of the commands available for the Fluke 45, Fluke 8842A, and HP 34401A, with the exception of the self-test and calibration commands. You must always calibrate the Meter using the SCPI language setting. The calibration commands from the other multimeters will not be executed.

Be aware that measurement timing, triggering, and range mapping may be different in the alternate language compatibility modes.

8845A/8846A

Programmers Manual

FLUKE 45 Command Emulation Summary

Computer Interface Command Set

RS-232 and IEEE-488 commands, grouped by related function, are listed in the tables that follow. These commands are identical, except where indicated. A parameter that must be supplied by the user or a string returned by the Meter is enclosed in angle brackets (<value>).

• IEEE-488 Common Commands (Table 20)

• Function Commands and Queries (Table 21)

• Function Modifier Commands and Queries (Table 22)

• Range and Measurement Rate Commands and Queries (Table 23)

• Measurement Queries (Table 24)

• Compare Commands and Queries (Table 25)

• Trigger Configuration Commands (Table 26)

• Miscellaneous Commands and Queries (Table 27)

• RS-232 Remote/ Local Configuration Commands (Table 28)

IEEE-488 Capabilities and Common Commands

Table 20 summarizes the IEEE-488 Commands that are common between the Fluke 8845A/46A and the Fluke 45.

Table 20. IEEE-488.2 Common Commands

Command Name Description

*CLS Clear Status Clears all event registers summarized in the status byte,

except for "Message Available," which is cleared only if *CLS is the first message in the command line.

*ESE <value> Event Status Enable Sets Event Status Enable Register to <value>, an integer

between 0 and 255, where <value> is an integer whose binary equivalent corresponds to the state (1 or 0) of bits in the register. If <value> is not between 0 and 255, an Execution Error is generated.

EXAMPLE: decimal 16 converts to binary 00010000. Sets bit 4 (EXE) in ESE to 1.

*ESE? Event Status Enable

Query

*ESR? Event Status

Meter returns the <value> of the Event Status Enable Register set by the *ESE command, where <value> is an integer whose binary equivalent corresponds to the state (1 or 0) of bits in the register.

Meter returns the <value> of the Event Status Register and then clears it. The <value> is an integer whose binary equivalent corresponds to the state (1 or 0) of bits in the register.

Digital Multimeter

Table 20. IEEE-488.2 Common Commands (cont.)

Command Name Description

*IDN? Identification Query Meter returns the identification code of the meter as four fields

separated by commas. These fields are: manufacturer ("FLUKE"); model (“45"); seven-digit serial number; version of main software and version of display software. FLUKE, 45, 9080025, 2.0, D2.0)

*OPC Operation Complete

Command

*OPC? Operation Complete

Query

*RST Reset Meter performs power-up reset, except that the state of IEEE-

*SRE <value>

Service Request

Enable

Meter sets the Operation Complete bit in the Standard Event Status Register when parsed.

Meter places an ASCII "1 " in the output queue when parsed.

488 interface is unchanged, including: instrument address, Status Byte, and Event Status Register.

Sets the "Service Request Enable Register" to <value>, an integer between 0 and 255. The value of bit six is ignored because it is not used by the Service Request Enable Register.

FLUKE 45 Command Emulation Summary

[1]

(example:

Note that <value> is an integer whose binary equivalent corresponds to the state (1 or 0) of bits in the register. If <value> is not between 0 and 255, an Execution Error is generated.

*SRE?

*STB? Read Status Byte Meter returns the <value> of the Status Byte with bit six as the

*TRG Trigger Causes the meter to trigger a measurement when parsed.

*WAI Wait-to-continue Command required by IEEE-488.2 standard. Non-operational

[1] The user defined IDN 8845A/46A command identification response will set the *IDN? Indentification query

response for both 8845A/46A and Fluke 45 modes of operation. IDN is an “8845A/46A” only command.

Service Request

Enable Query

Meter returns the <value> of the Service Request Enable Register (with bit six set to zero); <value> is an integer whose binary equivalent corresponds to the state (1 or 0) of bits in the register.

Master Summary bit.

<value> is an integer whose binary equivalent corresponds to the state (1 or 0) of bits in the register.

in Fluke 45 Dual Display Multimeter. Command accepted but has no effect.

8845A/8846A

Programmers Manual

Function Commands and Queries

The commands in Table 21 lists the measurement function commands for the Fluke 45. See Tables 22A and 22B for ranges and measurement rates. Commands under Primary Display and Secondary Display cause functions to be performed using the primary display or secondary display, respectively.

Table 21. Fluke 45 Function Commands and Queries

Primary Display

AAC

ADC

—

CONT

DIODE

FREQ

FUNC1 ?

OHMS

VAC

VDC

Commands

Secondary Display

AAC2

ADC2

CLR2

—

DIODE2

FREQ2

—

FUNC2?

OHMS2

VAC2

VDC2

Function

AC current

DC current

Clears measurement from secondary display if one shown.

Continuity test. Available in the primary display only.

Diode test

Frequency

Meter returns the function selected for the primary display as command mnemonic.

EXAMPLE: If frequency is selected for the primary display, "FUNC1?" returns "FREQ".

Meter returns the function selected for the secondary display as command mnemonic. If the secondary display is not in use, an Execution Error is generated.

EXAMPLE: If frequency is selected for the secondary display, FUNC2? returns "FREQ".

Resistance

AC volts

DC volts

Digital Multimeter

FLUKE 45 Command Emulation Summary

Function Modifier Commands and Queries

The commands in Table 22 relate to the function modifiers. A function modifier causes the Meter to modify the normal operation of a measurement function (or perform an action on a measurement) before displaying a reading.

Table 22. Function Modifier Commands and Queries

Command Description

AFILT (on/off)

AFILT?

DBCLR

DBPOWER

DBREF <value>

DBREF?

DFILT (on/off)

Activates or deactivates the 3-pole analog filter to improve noise immunity for dc functions. This filter is only available in DCV, DCI, 2-Wire and 4-Wire resistance. The default setting is OFF. If an attempt is made to enable the filter in a mode not permitted, the request is ignored.

Returns the state of the analog filter.

Meter enters decibels modifier. Any reading shown in the primary display is in decibels.

An Execution Error is generated if the meter is not in a volts ac and/or dc function.

Meter exits the decibels modifier and displays readings in normal units. Also clears dB and Power modifiers.

Meter enters dB Power modifier if the reference impedance is set to 2, 4, 8, or 16 ohms and a voltage function has been selected. Otherwise, an Execution Error is generated. In dB Power, readings shown in the primary display are in watts.

Set dB reference impedance to a <value> shown in Table 22A. This value corresponds to the reference impedance (ohms) indicated.

If <value> is not a value shown in Table 22A, an Execution Error is generated.

Table 22A. Reference Impedance Values

Value

1 2 3 4 5 6 7 8 9 10 11

Meter returns a <value> shown in Table 22A. This value corresponds to the reference impedance indicated.

Activates or deactivates the digital averaging filter to reduce noise for dc functions. This filter is only available in DCV, DCI, 2-Wire and 4-Wire resistance. The default setting is ON. If an attempt is made to enable the filter in a mode not permitted, the request is ignored.

Ref Impedance

2 4 8 16 50 75 93 110 124 125 135

Value

12 13 14 15 16 17 18 19 20 21

Ref Impedance

150 250 300 500 600 800 900 1000 1200 8000

8845A/8846A

Programmers Manual

Command Description

DFILT?

MOD?

Range and Measurement Rate Commands and Queries

The commands in Table 23 relate to ranging and measurement rates (i.e., readings/ second). In the autorange mode, the Meter automatically selects a range for each reading; in the manual range mode, the user selects a fixed range.

Command Description

AUTO

AUTO?

FIXED

RANGE <range>

Table 22. Function Modifier Commands and Queries (cont.)

Returns the state of the digital averaging filter.

Meter returns a numeric value indicating modifiers in use. 8=dB, 16=dB Power, 32 = Relative, 64 = Compare.

Table 23. Range and Measurement Rate Commands and Queries

Causes the meter to enter the autoranging mode on the primary display. If the autorange mode cannot be selected (e.g., if dB or diode/continuity test is selected), an Execution Error is generated.

Causes meter to return "1" in autorange, or "0" if it is not.

Causes the meter to exit autoranging on the primary display and enter manual ranging. The present range becomes the selected range.

Sets the primary display to the range designated by <range>, where <range> is a number between 1 and 7 that corresponds to a range shown in Tables 5-12A and 5-12B.

Table 23A. Ranges at Fast & Medium Measurement Rate

Range

Value

1 2 3 4 5 6 7

* 1000 V dc, 750 V ac

Range

Value

1 2 3 4 5 6 7

* 1000 V dc, 750 V ac

Voltage

Range

300 mV

3 V

30 V

300 V

1000 V dc*

ERROR ERROR

Table 23B. Ranges at Slow Measurement Rate

Voltage

Range

100 mV 1000 mV 10 V 100 V 1000 V dc* ERROR ERROR

Ohms

Range

300 Ω

3 k Ω

30 k Ω

300 k Ω

3 M Ω

30 M Ω

300 M Ω

Ohms

Range

100 Ω 1000 Ω 10 k Ω 100 k Ω 1000 k Ω 10 M Ω 100 M Ω

Current

Range

30 mA

100 mA

10 A ERROR ERROR ERROR ERROR

Current

Range

10 mA 100 mA 10 A ERROR ERROR ERROR ERROR

1000 Hz 10 kHz 100 kHz 1000 kHz 1 MHz ERROR ERROR

Frequency

Range

1000 Hz

10 kHz

100 kHz

1000 kHz

1 MHz ERROR ERROR

Frequency

Range

Digital Multimeter

Table 23. Range and Measurement Rate Commands and Queries (cont.)

Command Description

RANGE1?

RANGE2?

RATE <speed>

RATE?

Returns the range presently selected on the primary display.

Returns the range presently selected on the secondary display. If the secondary display is inactive, an Execution Error is generated.

Sets the measurement rate to <speed>. RATE <speed> is either "S" for slow (2.5 readings/second), "M" for medium (5 readings/second), or "F" for fast (20 readings/second). "S", "M", and "F" can be sent as either upper- or lower-case letters. Any other entry for <speed> generates an Execution Error.

Returns <speed> as "S" for slow (2.5 readings/second), "M" for medium (5.0 readings/second), or "F" for fast (20 readings/second).

FLUKE 45 Command Emulation Summary

Measurement Queries

The commands in Table 24 cause the Meter to return readings shown on the primary and/or secondary displays.

Table 24. Measurement Queries

Command Description

MEAS1?

MEAS2?

MEAS?

VAL1?

VAL2?

VAL?

Meter returns the value shown on the primary display after the next triggered measurement is complete.

Meter returns the value shown on the secondary display after the next triggered measurement is complete. If the secondary display is off, an Execution Error is generated.

If both displays are on, the Meter returns the value shown on both displays after the next triggered measurement is complete in the format selected. These values are separated by a comma (format 1) or a space, measurement units, a comma and space (format 2).

Example: +1.2345E+0,+6.7890E+3<CR><LF>

If the secondary display is not on, MEAS? is equivalent to MEAS1?

Note If MEAS is used in external trigger (TRIGGER 2 through TRIGGER 5), unexpected results will be obtained.

Meter returns the value shown on the primary display. If the primary display is blank, the next triggered measurement is returned.

Meter returns the value shown on the secondary display. If the secondary display is blank, the next triggered measurement is returned. If the secondary display is off, an execution error is generated.

If both displays are on, the Meter returns the value shown on both displays. These values are separated by a comma.

Example: +1.2345E+0,+6.7890E+3<CR><LF>. If the secondary display is not on, VAL is equivalent to VAL1. If a display is blank, the next triggered measurement on that display (or displays) is returned.

8845A/8846A

Programmers Manual

Compare Commands and Queries

The commands in Table 25 cause the Meter to determine whether a measurement is higher than, lower than, or within a specified range.

Command Description

COMP

COMP?

COMPCLR

COMPHI <high value>

COMPLO <low value>

Table 25. Compare Commands and Queries

Meter enters compare (COMP) function.

Meter returns "Hl" if the last COMP measurement reading was above the compare range, "LO" if it was below it, "PASS" if within compare range, or "— " if a measurement has not been completed.

Meter exits compare function, and restores display to normal operation.

Sets HI compare (COMP) value to <high value>, where <high value> can be a signed integer, signed real number without exponent, or signed real number with exponent.

Sets LO compare (COMP) value to <low value>, where <low value> can be a signed integer, signed real number without exponent, or signed real number with exponent.

Trigger Configuration Commands

The commands in Table 26 set and return the trigger configuration.

Table 26. Trigger Configuration Commands

Command Description

TRIGGER <type>

TRIGGER?

Sets the trigger configuration to <type>.

<type> corresponds to a number between 1 and 5 selected from Table 26A. If the <type> entered is not one of these listed numbers, an Execution Error is generated.

Table 26A. Trigger Type

Type Trigger Rear Trigger Settling Delay

Internal

External

[1] Although the Fluke 45 disabled the rear-panel trigger for these trigger types, the 8845A/46A leaves the rear-panel trigger enabled.

When the input signal is not stable, select a trigger type with the settling delay (type 3 or 5) enabled before a measurement is triggered.

Returns the trigger <type> set by the TRIGGER command.

Enabled Enabled

[1]

Off On Off On

Digital Multimeter

FLUKE 45 Command Emulation Summary

Miscellaneous Commands and Queries

Miscellaneous commands and queries are summarized in Table 27.

Table 27. Miscellaneous Commands and Queries

Command Description

^C (CNTRL C)

SERIAL?

The RS-232 equivalent of IEEE-488 DCL. Causes <CR><LF> and =><CR><LF> to be output.

Meter returns its serial number.

RS-232 Remote/Local Configurations

The commands in Table 28 are used with the RS-232 interface to set up the Remote/ Local configuration of the Meter. These commands are valid only when the RS-232 interface is enabled.

Table 28. RS-232 Remote/Local Configuration Commands

Command Description

REMS

RWLS

LOCS

LWLS

Puts the Meter into remote state where all front-panel keys, except the local key, are disabled. LOCAL is shown above the first soft key in the display.

Puts the Meter in the remote state, with front-panel lockout. LOCKED is shown in the display. When in RWLS, all front panel buttons are disabled.

Puts the Meter in the local state, i.e., local operating mode without lockout. All front panel buttons are enabled.

Puts the Meter in the IEEE-488 LWLS state, i.e., local operating mode lockout. All front panel buttons are disabled.

Triggering Output

The Meter takes measurements when it is triggered to do so. The five available trigger types are listed in Table 29. All available trigger methods fall into two basic categories:

• Internal triggering uses the Meter’s internal trigger circuit for a continuous source of

triggers.

• External triggering comes from a source outside the Meter controlled by the user.

Setting the Trigger Type Configuration

To select a trigger type over the computer interface, send the command:

TRIGGER <type>

where <type> is a number between 1 and 5 that identifies a trigger type. If <type> is not one of these numbers, an Execution Error is generated.

Select a trigger type that enables the settling delay (type 3 or 5) when the input signal is not stable before a measurement is triggered.

8845A/8846A

Programmers Manual

External Triggering

A measurement can be externally triggered in three ways:

To trigger a measurement over the RS-232 or IEEE-488 computer interface, send the Meter a *TRG command over the computer interface. The GET command is only valid for the IEEE-488 interface.

When set for external trigger, the Meter will trigger measurements when a negative-going signal is applied to the rear-panel trigger jack.

• External trigger.

• GET command (IEEE-488 Interface only)

• *TRG command

Note

The Fluke 45 provides a method of triggering through its RS-232 port. The 8845A and 8846A do not provide this method of triggering.

Table 29. Trigger Types

Type Trigger Rear Trigger Settling Delay

1 2 3 4 5

[1] Although the Fluke 45 disabled the rear-panel trigger for these trigger types, the 8845A/46A leaves the rear-panel

trigger enabled.

Internal External External External External

Enabled Enabled

[1]

Off On Off On

Using FlukeView Forms

You can use FlukeView Forms to download and store readings from the Meter to a PC running MicroSoft’s Windows operating system. FlukeView Forms Basic Documenting Software must first be installed on the PC. Refer to the FlukeView Forms Installation

Guide to install FlukeView Forms on your Windows PC.

Note

The Meter’s RS-232 port must be enabled and properly configured before FlukeView forms will communicate with the Meter. In addition, the Fluke 45 command language must be selected in the Meter.

To connect and configure the Meter to the PC with the installed FlukeView Forms Basic Documenting Software:

1. Connect a null-modem cable between the RS-232 port of the Meter and the PC’s RS-

232 port.

2. Open FlukeView Forms Documenting Software.

3. The current COM serial port setting is displayed at the bottom right of the FlukeView

Forms Basic window. Double-click on it to change the COM port setting to the virtual COM port used by the null-modem cable.

4. Turn the Meter on.

5. Select the Fluke 45 Command language by following the instructions in the Selecting

the Program Language section of Chapter 3 of the Users Manual.

Digital Multimeter

FLUKE 8842A Emulation Mode

6. Ensure the Meter’s RS-232 port is set to 9600 Baud, No parity, and Echo Off using

the instructions found in the Configuring the RS-232 Port section of Chapter 3 Users Manual.

7. Follow the instructions for transferring data from the Meter to the PC, found in the

online FlukeView Forms Users Manual.

FLUKE 8842A Emulation Mode

The Fluke 8842A emulation mode is only available through the GPIB interface. Whenever the 8846A or 8845A has the RS-232 or LAN interface selected, 8842A emulation mode is not selectable through the front panel.

The 8842A IEEE-488 commands are listed in the following tables. These commands are identical, except where indicated. For operational differences and commands that are not supported in the 8845A or 8846A, refer to Appendix D.

Example Notes

In the examples in this manual, device-dependent commands are shown enclosed within quotation marks, as they would be entered in Fluke BASIC. For clarity, the commands are also separated by spaces. However, the spaces are are not necessary and may be omitted.

Example Explanation

“* F3 R1 S1 T2” This example is equivalent to “*F3R1S1T2” or

“*,F3,R1,S1,T2”.

Using the Fluke 1722A Instrument Controller, these commands might be written into a BASIC program as shown in Figure 5. Examples using other controllers are given at the end of this section.

Here is a typical command string as it might be sent from a Fluke 1722A Instrument Controller. The string configures the meter and triggers a reading. The PRINT command automatically sends terminators (CR, LF, and/or EOI) to the meter at the end of the command string.

PRINT @3, “* F3 R4 S1 T2 ?”

IEEE-488 bus address

Resets the meter to the

power-up configuration

Selects the 2 WIRE kΩ function

Selects the 200 kΩ range

Selects the medium reading rate

Selects the external trigger mode

(Rear panel trigger disabled)

Triggers a reading

Figure 5. Typical Command String for 8842A Emulation

caw65.eps

Examples of 8842A emulation output data show the terminators CR and LF. The terminator EOI is not shown because it is a uniline message. However, the terminators CR, LF, and EOI are all selectable using the Write commands.

8845A/8846A

Programmers Manual

Function Commands

F1 V dc (Default) F2 V ac F3 2 WIRE kΩ F4 4 WIRE kΩ F5 mA dc F6 mA ac

Range Commands

R0 Autorange On (Default) R1 200 mV, 200 Ω R2 2 V, 2 kΩ R3 20 V, 20 kΩ R4 200 V, 200 kΩ, 200 mA dc R5 1000 V dc, 700 V ac, 2 MΩ, 2000 mA R6 20 mΩ R7 Autorange Off R8 20 mV, 20 Ω

Reading Rate Commands

S0 Slow (Default) S1 Medium S2 Fast

Trigger Mode Commands

Command

T0 (Default)

T1 T2 T3 T4

Trigger

Mode

Internal External External External External

Setting

Delay

On On Off Off

Offset Commands

B0 Offset Off (Default) B1 Offset On

Display Commands

D0 Normal Display (Default) D1 Blank Display

Suffix Commands

Y0 Disable Output Sffix Y1 Enable Output Suffix

Terminator Commands

W0 Enable CR LF EOI (Default) W1 Enable CR LF Only W2 Enable CR EOI Only W3 Enable CR Only W4 Enable LF EOI Only W5 Enable LF Only

Figure 6. 8842A Emulation Device-Dependent Command Set

Clear Commands

* Device Clear (Reset meter to default conditions) X0 Clear Error Register

Single-Trigger Commands

? Trigger Measurement

Get Commands

G0 Get Instrument Configuration (F,R,S, and T) G1 Get SRQ Mask G3 Get User-Defined G4 Get Calibration Status G5 Get IAB Status (Input F/R, Autorange On/Off, Offset On/Off) G6 Get YW Status (Suffix Enabled/Disabled, Terminator Selection) G7 Get Error Status G8 Get Instrument Identification

Put Commands

P0 Put Instrument Configuration (F,R,S, and T) P1 Put SRQ Mask

Put Command Format

N <value> P0 N <value> P1

SRQ Mask Values

00 for SRQ Disabled (Default) 01 for SRQ On Overrange 16 for SRQ On Data Available 32 for SRQ On Any Error

Note: Add SRQ mask values for connections. Example: 33 for SRQ on overrange or

any error.

Self-Test Command

Z0 Begin Self-Test

Terminators

CR (Carriage Return) Execute LF (Line Feed) Execute EOI (End Or Identify) Execute GET (Group Execute Trigger) Trigger and Execute

Note: GET is an interface message.

caw66.eps

Digital Multimeter

FLUKE 8842A Emulation Mode

Device-Dependent Command Set

Device-dependent commands are the heart of 8842A emulation remote control. They tell the Meter how and when to make measurements, when to put data on the bus, when to make service requests, etc. The complete set of device-dependent commands is listed in Figure 6. The commands may be entered using either upper- or lower-case letters.

Device-dependent commands are device-dependent messages. For the Meter to receive them, they must be sent over the IEEE-488 bus when the Meter is in remote and has been addressed as a listener.

The following paragraphs describe the device-dependent commands in alphabetical order. Special characters (* and ?) are described last.

Bn (Offset Commands)

When the Meter receives the B1 command, the Meter stores the present reading as an offset for the present function. The B0 command cancels the offset. Only one offset is allowed at a time.

The offset status (not the offset value) can be read using the G5 command. The Meter defaults to B0 on both power-up and on any device-clear command (*, DCL, or SDC).

Dn (Display Commands)

The Display commands allow the user to blank the display in the Meter. The D0 command causes the display to operate normally, and is the default on power-up and upon any device-clear command (*, DCL, or SDC).

The D1 command blanks the display. The D1 command is used for best performance when high IEEE-488 Interface Data rates are required.

Fn (Function Commands)

The function commands duplicate the front panel function buttons. The Meter defaults to Fl on power-up and on any device-clear command (*, DCL, or SDC). If F0 is sent to the Meter, it is internally converted to F1. The function setting can be read using the G0 command.

As with the front panel commands, selecting F6 automatically selects the 2000 mA range (R5). If the instrument is in range R8, commanding F5 automatically selects the 200 mA range (R4). If the instrument is in R1 through R6, commanding F5 automatically selects the 2000 mA range (R5). If the Meter is in a resistance function (F3 or F4) and in R6, selecting any other function automatically selects R5. If the Meter is in range R8 and F2 or F3 is commanded, range R1 is selected.

Get Commands

The Get commands "get" information from the Meter for the controller. Each Get command loads the output buffer with an output string in the format shown in Figure 7. Status data (the output from Get commands G0, G1, G3, G4, G5, G6, G7 and G8) is interpreted as shown in Table 30. The Get commands should not be confused with the interface message GET (Group Execute Trigger).

8845A/8846A

Programmers Manual

Output Data Type Format

Numeric Data +n.nnnnnE+nn[suffix][CR][LF][EOI] (From trigger)

Examples:

+12.3456E+6 Measured value +12.3456E+6, Ohm Measured value

-9.99999E+9 Overrange (≥ 200,000 counts) +9.99999E+9,>VDC Overrange (≥ 200,000 counts) +1.0032E+21 Error Message

Instrument Configuration Data nnnn [CR] [LF] [EOI] (From G0, G4, G5, G6, and G7) Example: 1100 Default G0 value

SRQ Mask Data nn [CR] [LF] [EOI] (From G1) Example: 32 SRQ on any error

Numeric data is always in volts, amps, or ohms. The terminators CR, LF, and EOI are selected with the Terminator Commands (Wn). The suffix, defined below, is enabled with the Y1 command and disabled with the Y0 command. (Default = Y0.)

Suffix Format

Leading Comma (Always present in suffix). Most versions of BASIC expect multiple input values to be separated by commas. (e.g.,input@I,N,S$) to acquire the numeric portion and suffix string.

> Reading is overrange (≥ 200,000 counts) <space> Reading is not overrange but can be over voltage (> 1000 V dc or 700 Vac)

V dc V ac

Ohm

IDC IAC

Function Indicator

Figure 7. 8842A Emulation Data Output Format

caw67.eps

Digital Multimeter

Table 30. 8842A Get Commands

Command Output String Description

frst f = 1 – 6 for function selection

nn nn = 00 for SRQ disabled

G2 Error 51 Not supported in 8842A emulation mode.

r = 1 – 6 for selected range s = 0 – 2 for selected measurement rate t = 0 – 4 for selected trigger mode

01 for SRQ on overrange 16 for SRQ on data available 32 for SRQ on any error Note: SRQ mask values may be added for combinations. Example: 33 for SRQ on overrange or any error.

FLUKE 8842A Emulation Mode

[1]

G8 FLUKE,8842A, nnnnnnn,V5.0 nnnnnnn = Instrument serial number

[1] The 8845A and 8846A have an error queue of 16. For multiple errors, G7 will dequeue the errors one by one but

will not clear the ERROR indicator on the front panel when the queue is empty. X0 clears the ERROR annunciator.

FL8842A.1-8-2008 Can’t set user defined message in 8842A

emulation.

10vm v = 0 Not in cal verification

m = 0 Not in calibration mode

1iab i = 0 Front-panel inputs selected

1 Rear-panel inputs selected a = 0 Autorange on 1 Autorange off (manual ranging) b = 0 Offset off 1 Offset on

10yw y = 0 Output suffix disabled

1 Output suffix enabled w = 0 – 5 Selected terminator command

10nn nn = Error code

The output data from some Get commands starts with a leading 1 or 10. This prevents the controller from suppressing leading zeroes and gives a uniform four-character length to all instrument configuration data (the data from Get commands G0, G4, G5, G6, and G7).

The Get commands are described further in the following paragraphs. For more information about output data, see Syntax Rules later in this section.

G0 (Get Instrument Configuration)

The G0 command copies the function, range, reading rate, and trigger mode of the Meter into the output buffer in the format shown in Figure 7. The four digits returned represent the arguments for the equivalent F, R, S, and T commands, as shown in Table 30. An example output string follows:

Example Explanation

3410 CR LF 3: F3 (2-Wire kΩ function)

8845A/8846A

Programmers Manual

4: R4 (200 kΩ range)

1: S1 (Medium reading rate)

0: T0 (Continuous trigger)

The second digit, which can vary from 1 to 6, indicates what measurement range the Meter is in regardless of whether the Meter is in autorange or manual range.

The output string from a G0 command is acceptable as an argument for an "N" command. This allows you to configure the Meter from the front panel and then record the configuration over the bus for future use with a P0 command.

G1 (Get SRQ Mask)

The G1 command copies the present SRQ mask into the output buffer in the format shown in Figure 7. The SRQ mask values are explained in Table 30. An example output string follows. For more information about the SRQ mask, see the “Status Data” section later in this section.

Example Explanation

33 CR LF Enable SRQ on any error or overrange.

G3 (Get User-Defined Message)

The G3 command loads the output buffer with the indentification string and calibration date of the Meter.

Example Explanation

FL8842A 10-8-2008 CR LF Identifies Meter and gives calibration date.

G4 (Get Calibration Status)

The command loads the output buffer with the instrument's calibration status in the format shown in Figure 7. The status is represented by a four-digit integer which is interpreted in Table 30.

The first two digits are always 1 and 0. The third digit indicates whether or not the calibration verification mode is enabled. The fourth digit indicates whether or not the calibration mode is enabled. Since the Meter can only be calibrated in 8845A/8846A mode, the response to the G4 command in the 8842A emulation mode will always be

1000.

Example Explanation

1000 CR LF 1: Leading 1

0: Leading 0

0: Not in cal verification

0: Cal mode disabled

G5 (Get IAB Status)

The G5 command loads the output buffer with the IAB status in the format shown in Figure 7. As Table 30 explains, the IAB status is a four-character string which indicates the status of the FRONT/REAR switch (front or rear analog inputs selected), the autorange feature (autorange on or off), and the OFFSET feature (OFFSET on or off). The first digit is always 1. An example output string follows.

Example Explanation

Digital Multimeter

1011 CR LF 1: Leading 1

FLUKE 8842A Emulation Mode

0: FRONT inputs

1: Autorange off

1: OFFSET feature on

It is useful to know whether autorange is on or off because this information is not available from the G0 command. For example, the G0 command could indicate that the Meter was in the 200 mV range, but it would not indicate whether the Meter was in autorange or manual range

G6 (Get YW Status)

The G6 command loads the output buffer with the YW status in the format shown in Figure 7. The YW status is a four-character string which indicates which terminators are selected and whether the output suffix is enabled or disabled, as shown in Table 30. The first two digits are always 1 and 0. An example output string follows.

Example Explanation

1015 CR LF 1: Leading 1

0: Leading 0

1: Y1 (enable output suffix)

5: W5 (enable LF only)

G7 (Get Error Status)

The G7 command copies the error status register into the output buffer in the format shown in Figure 7. The first two digits are always 1 and 0. The second two digits represent the appropriate error code, if an error has occurred. (Error codes are listed in Appendix A). If an error has not occurred, the second two digits are 00. An example output string follows.

Example Explanation

1071 CR LF 1: Leading 1

0: Leading 0

71: Syntax error in device-dependent command string

The G7 command gives the error status as it exists when the command is executed at its position in the input string. The G7 command does not clear the error status register. For more information about error messages, see the Output Data section later in the section.

G8 (Get Instrument Identification)

The G8 command copies the Meter instrument identification into the output buffer in the format shown in Figure 7. The identification is represented by four comma separated fields that are interpreted in Table 30.

The first field indicates the manufacturer, the second indicates the instrument model number, the third is always the serial number, and the fourth indicates the version number of the IEEE-488 interface software.

Example Explanation

FLUKE,8842A,1234567,V5.0 CR LF This Meter is a Fluke 8842A with IEEE-488 interface

software version 5.0.

8845A/8846A

Programmers Manual

N (Numeric Entry Command)

Format Explanation

N<numberic entry> Where <numeric entry> is one of the following:

Example Explanation

“N12001” Enters the five-digit integer 12001

“N-1.23E2” Enters -1.23 x 10

“N+154.33E-1” Enters 1.5433 x 10

The N command enters numeric values for use with subsequent Put commands. The interpretation of the numeric value depends on which Put command it is used with.

The E can be used within an N command for entering an exponent of 10. The N can be used without an E, but an E requires a prior N. The exponent can be any integer from -9 to +9.

The mantissa may exceed 5-1/2 digits. The 8842A accurately calculates the appropriate exponent and then disregards all but the first 5-1/2 digits of the mantissa. However, a syntax error will occur if the numeric entry overflows the input buffer.

Example Explanation

“N123456789” Enters +1.23456 x 10

Put Commands

The Put commands P0 and P1 set up the configuration of the Meter and its operating modes by entering ("putting") information in the appropriate registers. The put commands are described further in the following paragraphs.

P0 (Put Instrument Configuration)

Format Explanation

N<frst>P0 Where <frst> is a four-digit integer interpreted as

Example Explanation

“N3120 P0” Identical to F3 R1 S2 T0. Selects 2-Wire kΩ function,

The P0 command allows broadside loading of the Function, Range, Reading Rate, and Trigger Mode commands (F, R, S, and T). The codes for these commands are listed in Figure 6.

arguments for the F, R, S, and T commands.

200Ω range, fast sample rate, and continuous trigger.

A numeric entry for P0 must be within +1000 and +6824. Each of the four digits must not exceed its maximum allowed value (6, 8, 2, and 4, respectively) or an error message will occur and the instrument configuration will remain unchanged. The entry may be expressed as an integer, real number, or real number with exponent, as described under the N command. Any fractional part is ignored.

Example Explanation

“N3112 P0” Sets the Meter to F3, R1, S1, and T2.

Digital Multimeter

FLUKE 8842A Emulation Mode

P1 (Put SRQ Mask)

Format Explanation

N< SRQ mask >P1 Where < SRQ mask> is a two-digit integer from 00 to

63.

The P1 command is used to program the 8842A to make service requests on user-specified conditions. The two-digit code for the SRQ mask is interpreted in Table 30 under the G1 command. For more about the SRQ mask, see the “SRQ Mask” section later in this section.

Numeric entries for the P1 command must be between 0 and +63 (inclusive), or an error will occur and the SRQ mask will remain unchanged. The entry may be expressed as an integer, real number, or real number with exponent, as described under the N command. Any fractional part is ignored.

Example Explanation

“N0.17E+2 P1” Sets SRQ mask to 17. Enables SRQ on data available

or overrange.

“N1 P1” Sets SRQ mask to 01. (A leading zero is assumed.)

Enables SRQ on overrange.

Rn (Range Commands)

The Range commands duplicate the front panel range buttons. For example, R0 selects autorange, and R3 selects the 20V/20 kΩ range.

The R7 command turns autorange off, just as the RANGE button does when it is toggled. Command R7 puts the Meter into manual range, selecting whatever range the instrument is in when the command is received.

The Meter defaults to R0 on power-up and any device-clear command (*, DCL, or SDC). The range setting can be read using the G0 command.

Sn (Reading Rate Commands)

The 8842A defaults to S0 on power-up and any device-clear command (*, DCL, or SDC). The reading rate can be read using the G0 command. The reading rate command also selects the number of digits displayed and the filter setting.

Tn (Trigger Mode Commands)

The Trigger Mode commands duplicate the front panel TRIG button. In addition, the commands can enable or disable the automatic settling time delay.

The front panel TRIG button is enabled only while the instrument is under local control.

In the continuous trigger mode (T0), triggers are initiated at the selected reading rate. Each new reading is loaded into the output buffer as it becomes available, unless the Meter is busy sending previous output data.

Note

The trigger mode can be read using the G0 command. The Meter defaults to T0 on both power-up and any device-clear command (*, DCL, or SDC).

8845A/8846A

Programmers Manual

Wn (Terminator Commands)

The Terminator commands select what terminators the Meter appends to every output string. The available terminators are: Carriage Return (CR), Line Feed (LF), and End Or Identify (EOI).

CR and LF are ASCII control codes, sent over the data lines just like output data. EOI is a uniline message which is sent simultaneously with the last character in the output string. Normally, each output string is terminated with CR followed by LF and EOI.

The terminator selection can be read using the G6 command. The Meter defaults to W0 on power-up and any device-clear command.

X0 (Clear Error Register Command)

The X0 command clears the error status register of the Meter. After an X0 command is executed, a G7 command (Get Error Status) would return 1000 (no errors).

Note that the error status register is also cleared when any device-clear command (*, DCL, or SDC) is executed. However, X0 is useful for clearing the error status register without forcing a complete instrument clear (as do the device-clear commands).

Yn (Suffix Commands)

The Suffix commands enable or disable a suffix which the Meter can append to all numeric data. The suffix includes a comma, an overrange indicator (>), and a function indicator (VDC, VAC, OHM, IDC, or IAC). The suffix is illustrated in Figure 7. An example of suffixed data is given in the “Numeric Data and Error Messages” paragraph later in this section.

To read suffixed data with a controller using BASIC, one can read the whole line into a string variable and then convert the numeric part into a numeric variable. However, it is much easier to read the numeric part directly into a numeric variable and the suffix into a string variable. The leading comma of the suffix serves as a convenient delimiter. For example, a BASIC program statement might be:

INPUT @1,A, B$

The suffix status can be read using the G6 command. The Meter defaults to Y0 on powerup and any device-clear command (*, DCL, or SDC), unless in talk-only mode.

Z0 (Self-Test Command)

The Z0 command intiates the diagnostic self-tests.

Since the Meter is reset at the end of the self-tests, the Z0 command should be the last command in a given command string. The Meter will ignore any subsequent commands in the same command string.

When the self-tests are complete and no errors have occurred, the serial poll register will have bit 5 (Data Available) true and bit 6 (Any Error) false.

Device Clear Command

The asterisk command (*) is a device-dependent message which resets the Meter to the power-up default settings and clears all registers and buffers except for the input buffer. The remote/local status remains unchanged. The asterisk command performs the following:

1. Implements the default settings Fl, R0, S0, T0, D0, B0, Y0, W0.

2. Clears the error status register (equivalent to X0).

Digital Multimeter

FLUKE 8842A Emulation Mode

3. Zeros the SRQ mask, prohibiting service requests (equivalent to N0 P1).

4. Zeros the numeric entry register (equivalent to N0).

5. Zeros the serial poll register.

6. Sets the SRQ line false.

The asterisk command is executed in its proper turn in a string, just like any other command, without affecting the contents of the input buffer. All commands which precede the asterisk command are performed.

The asterisk command is useful to ensure that the Meter is initialized to the same state each time a program is run. By contrast, the similar interface messages DCL (Device Clear) and SDC (Selected Device Clear) cause the entire input buffer to be cleared immediately.

DCL, SDC, and the asterisk command are all considered to be device-clear commands because the results are so similar; however, DCL and SDC are not identical to the asterisk command described here.

? (Single-Trigger Command)

The Single-Trigger command (?) causes the Meter to take a reading and place the result into the output buffer. To accept this command, the Meter must be in external trigger mode (selected by the T1, T2, T3, or T4 command).

The Single-Trigger command is one of five ways to trigger a reading. Of these, only the Single-Trigger command (?) and the Group Execute Trigger command (GET) are loaded into the input buffer.

Input Syntax

The following paragraphs describe how to construct groups of commands for the 8842A command emulation. A few definitions are presented first, followed by a description of how the Meter processes input commands. Guidelines are then summarized in four syntax rules.

Definitions

• Output commands: Commands which load data into the output buffer. The output

commands are: the Get commands (G0 through G8); the Single-Trigger Command (?); the Continuous Trigger command (T0); and Group Execute Trigger (GET), not to be confused with the Get commands.

• Input terminator: An ASCII control code sent by the controller which tells the Meter

to execute all device-dependent commands since the previous terminator. Terminators are CR (Carriage Return), LF (Line Feed), EOI (End Or Identify), and GET (Group Execute Trigger).

• Input command string: One or more device-dependent commands followed by a

terminator

Input Processing

When the Meter receives commands from the bus, it stores them in a 350-character input buffer as a continuous string of characters. Commands in the input buffer are not executed or checked for syntax until an input terminator is received or the input buffer becomes full. The only valid input terminators are CR, LF, GET (Group Execute Trigger), and/or EOI.

8845A/8846A

Programmers Manual

When the Meter receives an input terminator, it executes the previous commands in the order in which they were received. As input characters are processed and executed, space is made available in the input buffer for new characters.

If the input buffer becomes full, the Meter stops accepting characters from the bus until all complete command strings currently in the input buffer have been executed. In this way, characters sent to the Meter are never lost due to buffer overflow.

In some instances, a terminator is automatically transmitted at the end of the controller's output string. For example, in Fluke BASIC, the PRINT statement always finishes with a CR LF pair. If a controller does not have this feature, the programmer must transmit a terminator explicitly.

The Meter accepts alphabetic characters in either upper or lower case. Spaces, commas, and control codes are ignored and are not placed in the input buffer. If the Meter receives a group of terminators (such as CR LF or CR LF EOI), only a single terminator is loaded into the input buffer. Numeric values used in PUT commands may be in NR1, NR2, or NR3 format as described in the IEEE-488 Codes and Formats Recommended Practice. (These correspond to the signed integer, real number, and realnumber-with exponent formats described under the N command).

Illegal commands (e.g., F9) generate an error message, but are otherwise ignored, and do not affect the instrument's configuration.

Example Explanation

“* F9” This would load the output buffer with an error

Syntax Rules

Four syntax rules should be followed when constructing input command strings. They are:

• RULE 1: Read output data only once.

To prevent old (previously read) data from being read a second time by mistake, the output buffer is always cleared after it has been read. If the output buffer is read twice without an intervening output command, the Meter will not respond to the second attempt to read the output buffer. (However, if the Meter is in T0, no intervening command is necessary.)

• RULE 2: Use no more than one output command per input command string.

Because the Meter has only one output buffer, it writes new data over old. If an input command string contains more than one output command, only the data from the last command can be read.

Example Explanation

“F1 T3 ? F2 ?” Improper construction. The second trigger writes over

message and select F1 (established by the * command).

the first. To obtain two readings, send two complete command strings (separated by terminators).

“F2 R3 S0 T3 ?” Correct construction. The string contains only one

output command.

“F2 R3 S0” Correct construction. It is permissible for a string not

to contain an output command.

• RULE 3: Read the output data generated by one input command string before

sending the next input command string.

Digital Multimeter

FLUKE 8842A Emulation Mode

Output data remains available in the output buffer until it is read, or until the next input command string is received. As soon as the controller finishes reading the output buffer, or as soon as the Meter receives a new input terminator, the Data Available bit in the serial poll register is set false. When this bit is false, data can no longer be read from the output buffer. Therefore, an output string which is available must be read by the controller before, rather than after, the next input command string is sent.

Rule 3 is most evident in the external trigger mode, and is best demonstrated by a programming example. The following program is written first incorrectly, and then correctly, in Fluke BASIC using the 1722A Instrument Controller.

Incorrect Example

100 PRINT @3, "T1 ? " 200 PRINT @3, "F4" 300 INPUT @3, A

In this incorrect example, the INPUT statement is located incorrectly for reading the measurement data from line 100. The new input command string "F4" disallows the reading of data from the output buffer.

Correct example

• RULE 4: If an input command string contains a trigger, enter the commands in the

following order:

a. Commands to configure the instrument (if any).

b. The trigger command.

c. Commands to re-configure the instrument (if any).

d. Terminator(s).

The principle behind this rule is that the 8842A executes all commands in the exact order they are received, from left to right as written.

Example Explanation

“F3 F4 ?” Improper construction. F3 is effectively discarded.

“F3 ? F4” Correct construction. The Meter is configured in F3,

Output Data

The following paragraphs describe the data that can be loaded into the output buffer of the Meter and sent to the IEEE-488 bus. The paragraphs describe how and when data is loaded into the output buffer, the types of output data, and their relative priority.

100 PRINT @3, "T1 ? " 200 INPUT @3, A 300 PRINT @3, "F4"

and the trigger is executed. Then the Meter is left in F4.

Note that the Meter can also send data to the IEEE-488 bus from the serial poll register. For a description of this data, see the “Status Data” section later in the manual.

Loading Output Data

The output buffer is loaded when the Meter receives an output command, or when an error occurs. Output commands are those device-dependent commands which load the output buffer with data:

8845A/8846A

Programmers Manual

Because the Meter gives priority to input processing, it completely processes all characters in the input buffer before it loads the output buffer. When the output buffer is loaded, the Data Available bit in the serial poll register is set true.

Data from the output buffer is not actually loaded onto the IEEE-488 bus until the controller addresses the Meter as a talker. This is done by sending the interface message MTA (My Talk Address).

Types of Output Data

The types of data that can be loaded into the output buffer are shown in 7. Each type has its own format. Error messages, which are loaded into the output buffer if an error occurs, are formatted as numeric data.

Numeric Data and Error Messages

Numeric data is loaded into the output buffer in response to an instrument trigger. The exponent is always a multiple of 3, as in engineering notation.

• Get commands (G0 through G8)

• Single-trigger command (?)

• Group execute trigger (GET)

• Continuous Trigger (T0)

Numeric data is of constant length, It is 11 characters (plus terminators) when the suffix is disabled, and 16 characters (plus terminators) when the suffix is enabled.

The suffix is enabled by the Y1 command, and consists of five ASCII characters as shown in Figure 7. The suffix is appended only to numeric data, never to status data. The terminators are determined by the Terminator commands. The default is CR LF EOI.

There are three types of numeric data: measurement data, overrange indication, and error messages.

Overrange Indication

If a reading is overrange (≥200,000 counts), the measurement data has the following format:

±9.99999E+9 <suffix> <terminators>

Overvoltage readings (> 1000V dc or 700V ac) do not result in this display.

Error Messages

If the Meter detects an error, it loads an error message into the output buffer in the following numeric format:

The digits xx represent a two-digit error code. (Error codes are listed in Appendix A. The suffix is always suppressed for error messages.

+1.00xxE+21 <terminators>

Example Explanation

+1.0071E+21 CR LF ERROR 71: Syntax error in device-dependent

command string.

As with local operation, none of the errors are latching except for ERROR 31. If the mA DC or mA AC function is requested while the FRONT/REAR switch is in the REAR

Fluke 8846A, 8845A User manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Programmers Manual

Table of Contents

List of Tables

List of Figures

Introduction

Remote Operation

Safety Information

Symbols

Local and Remote Operation

Computer Interfaces

Optimizing System Speed for I/O Operation

Selecting the Remote Interface Port

Configuring the IEEE-488 Port

IEEE-488 Operating Limitations

Setting the IEEE-488 (GPIB) Port Address

Capability Commands

Interconnections

Configuring the RS-232 Port

Setting RS-232 Baud Rate

Setting RS-232 Parity and Data Bits

Setting RS-232 Stop Bits

Setting RS-232 Flow Control

Setting RS-232 End-Of-Line Character

Enabling and Disabling Fluke 45 Emulation Echo

RS-232 Modes of Operation

8845A/8846A Mode

Selecting Between Computer and Terminal Mode

Fluke 45 Mode

Operating with FlukeView Forms’

Interconnections

Fluke 8842A Emulation Mode

Configuring the Ethernet (LAN) Port

Setting the IP Address

Selecting Dynamic Host Configuration Protocol (DHCP)

Setting a Static Internet Address

Setting the LAN Subnet Mask

Reading the Domain Name

Configuring the Host Name

Reading the MAC Address

Configuring the LAN Default Gateway

Configuring the General Network Socket Port

Establishing an Ethernet Connection

Terminating an Ethernet Connection

Selecting the Programming Language

Getting Started With an Installation Test

Installation Test for RS-232 Connections

Installation Test for IEEE-488 Connections

If The Test Fails

How the Meter Processes Input

Input Strings

Input Terminators

Typical IEEE-488 Input Strings

Sending Numeric Values to the Meter

Sending Command Strings to the Meter

How the Meter Processes Output

Triggering Input

Internal Triggering

Service Requests (IEEE-488 Only) and Status Registers

External Triggering

Standard Event Status and Standard Event Status Enable Registers

Questionable Data Event Register and Questionable Data Enable Register

Status Byte Register

Reading the Status Byte Register

Service Request Enable Register

Supported SCPI Commands

SCPI Command Summary

SCPI Command Details

Using the MEASure? Command

Using the CONFigure Command

Setting Range and Resolution Parameters

Using the READ? Command

Using the INITiate Command

Using the FETCh? Command

Using the SENSe Subsystem to Configure the Meter

Programming for Math Operations

Programming the Trigger System