Fluke 80i-110s User Manual

The ideal current probe for

Fluke ScopeMeter®Test Tools

80i-110s AC/DC

Current Probe

Technical Data

Accurate current measurements
become more and more critical
when troubleshooting electric,
electronic, and automotive cir­cuits. The Fluke 80i-110s AC/DC
Current Probe is designed to
provide you with safe, high
accuracy measurements for a
wide range of applications.

The specially designed built­in safety features such as the
600 V rms rating at the input
jaws, output cable, and BNC
connector enhance work safety
in industrial and commercial
power distribution systems.

The probe is shielded for
high noise immunity, to prevent
unwanted noise when trou­bleshooting around noise gen­erating devices like adjustable
speed motor drives and ignition
systems.

The 80i-110s accurately
reproduces current waveforms
as they occur. Connect the
clamp to a Fluke ScopeMeter
Test Tool or other waveform
recording device like a Fluke
Power Harmonics Analyzer, to
clearly see distorted waveforms
that result from non-linear loads
such as computers, adjustable
speed motor drives, and elec­tronic ballasts for fluorescent
lighting.

Current clamps, not specifi­cally designed for oscilloscopes,
may add distortion to the actual
signal present in the system

under test. This makes it diffi­cult to get an accurate wave­form measurement.

The wide measurement
range from 50 milliamps to 100
Amps with a high fidelity milli­volt output gives you full
advantage of the high resolu­tion oscilloscope displays. This
gives you the true picture of
your current situation, and
allows useful measurements as
low as 10 milliamps.

The broad band frequency
response of the Fluke 80i-110s
AC/DC Current Probe from dc to
100 kHz supports a wide range
of applications where the probe
can be used. The probe can be
used to track down leakage
currents discharging car batter­ies or to measure dc currents
in an Uninterruptible Power

Supply (UPS), that uses a
battery backup system.

With its narrow jaw design,
the Fluke 80i-110s makes it
easy to take measurements in
tight spots.

Specifications

Electrical specifications

Current ranges:

0 to 10 A dc or ac peak
0 to 100 A dc or ac peak

Output signals:

10 A range: 100 mV/A
100 A range: 10 mV/A

Working voltage
(clamp jaws to ground):

600 V ac rms on Installation
Category II per IEC 1010-1
circuits.
300 V ac rms on Installation
Category III per IEC 1010-1
circuits.

Page 1 of 2, Document #2228
80i-110s AC/DC Current Probe
©2002 Fluke Corporation
Rev. A-9/2002

Fluke Corporation

PO Box 9090, Everett, WA USA 98206

Fluke Europe B.V.

PO Box 1186, 5602 BD
Eindhoven, The Netherlands

For more information call:

In the U.S.A. [phone] or
Fax [phone]
In Europe/M-East/Africa (31 40) 2 675 200 or
Fax [phone]
In Canada (800)-36-FLUKE or
Fax [phone]
From other countries [phone] or
Fax [phone]
Web access: http://www.fluke.com/

Fluke. Keeping your world

up and running.

Floating voltage (output
cable and connector to
ground):

600 V ac rms on Installation
Category II per IEC 1010-1
circuits.
300 V ac rms on Installation
Category III per IEC 1010-1
circuits.

Basic accuracy (dc to 1 kHz)

Extended accuracy:

For other frequencies, refer to
the appropriate input current
range and add the error listed
below to the “Basic Accuracy.”

Phase shift, dc to 65 Hz:

10 A range < 1.5 degree
100 A range < 1 degree

Input load impedance
(of host instrument):

> 1 MΩ in parallel with up to
100 pF

Useful bandwidth (-3 dB):

0 to 100 kHz

Rise or fall time: < 4 msec
Output noise level:

10 mV/A typ. 480 mV pk-pk
100 mV/A typ. 3 mV pk-pk

Maximum non-destructive
current:

0 to 2 kHz 140 A peak
2 to 10 kHz 110 A peak
10 to 20 kHz 70 A peak
20 to 50 kHz 30 A peak
50 to 100 kHz 20 A peak

Temperature coefficient:

2000 ppm/°C max. for tempera­ture from 0 °C to 50 °C (32 °F to
132 °F)

All Electrical Specifications are valid at a
temperature of 3 °C to 23 °C (5 °F to 73 °F)

General specifications

Dimensions:

67 x 231 x 36 mm
(2.6 x 9.1 x 1.4 inches)
Wei ght: 330 g (11.6 oz), battery
included

Output cable:

1.6 meters (63 inches)

Maximum conductor size:

11. 8 mm (.46 inch)

Maximum jaw opening:

12.5 mm (.49 inch)

Temperature:

Operating: 0 °C to 50 °C
(32 °F to 122 °F)
Non-operating: -30 °C to 70 °C
(-22 °F to 158 °F)

Relative humidity (operating):

0 to 85 % (0 °C to 35 °C; 32 °F
to 95 °F)
0 to 45 % (35 °C to 50 °C;
95 °F to 122 °F)

Altitude:

Operating: 0 to 2,000 meters
(0 to 6,560 feet)
Non-operating: 0 to 12,000
meters (0 to 40,000 feet)

Safety specification

Designed to meet the require­ments of IEC 1010 and CSA­C22.2 No. 1010.1: Installation
Category II, Working Voltage
600V, Pollution Degree 2.
Installation Category III,
Working Voltage 300V,
Pollution Degree 2.

Installation (Overvoltage)
Category II refers to local
level, appliances, and portable
equipment.

Installation (Overvoltage)
Category III refers to distribu­tion level and fixed installation
circuits inside a building
electrical service entrance.

Designed to meet the
requirements of UL1244,
Protection Class II Double
Insulation.

Battery information

Battery: 9 volt, IEC 6LR61
Consumption: 8.6 mA typical;

12 mA maximum

Service life:

55 hours typical, when Alkaline
IEC 6LR61 is used
40 hours minimum, when
Alkaline IEC 6LR61 is used

Battery indicator (ON):

Green LED dims when battery
voltage is below 6.5V

Overload indicator (OL):

Red LED indicates that wave­form or impulse is out of range

Instrument compatibility

The 80i-110s is compatible
with any Fluke ScopeMeter Test
Tool, Power Harmonics
Analyzer, Oscilloscope,
Multimeter, or other voltage
measurement device that has
the following features:

•

BNC input connector. A
BNC-to-banana adapter
(order PM 9081/001 from
Fluke) can also be used with
standard inputs on a digital
multimeter (DMM).

•

Input accuracy of 2 % or
better to take full advantage
of the accuracy of the probe.

•

Input impedance of greater
than or equal to 1 MΩ in
parallel with a maximum of
100 pF.

•

A passband of more than
four times the frequency
of the waveform to be
measured.

Warranty

One-year warranty

Input current

Error (after zero check)

dc or ac peak

100 mV/A 10 mV/A

50 mA to 10 A < 3 % of reading —

+ 50 mA

50 mA to 40 A — < 4 % of reading

+ 50 mA

40 to 80 A — < 12 % of reading

+ 50 mA

80 to 100 A — < 15 % of reading

Additional error
Frequency 100 mV/A 10 mV/A
1 to 5 kHz 3 % 3 %
5 to 20 kHz 12 % 12 %
> 20 kHz Not specified Not specified

Ordering information

Model

80i-110s AC/DC Current Probe

Page 2 of 2, Document #2228
80i-110s AC/DC Current Probe
©2002 Fluke Corporation
Rev. A-9/2002