Fluke 43B, 345 Data Sheet

Fluke 43B Power Quality Analyzer
Maintain power systems, troubleshoot power problems, diagnose equipment failures
The Fluke 43B Power Quality Analyzer performs the measurements you need to maintain power systems, troubleshoot power problems and diagnose equipment failures. All in a rugged handheld package.
operating time of 6.5 hours Combines the most useful capabilities of a
power quality analyzer, multimeter and scope Calculates 3-phase power on balanc
from a single-phase measurement Trends voltage, current, frequency, power
harmonics and captures voltage sags, transients and inrush current Monitoring functions help track intermittent
problems and power system performance Records two selectable parameters for up
to 16 days 20 measurement memories to save/recall
screens and data with cursor readings FlukeView®Software can log harmonics
and all other readings over time and provides a complete harmonics profile up to the
st
harmonic
51 Measures resistance, diode voltage drop,
continuity, and capacitance Users/applications manual and power quality
video to help answer tough questions Complete package with voltage probes and
400 A current clamp, FlukeView Software and optically isolated interface cable 3 year warranty on the Fluke 43B, 1 year on
accessories
ed loads,
On screen graphics show you how to set up
3-phase power measurements
atts, power factor, displac
W
factor (Cos φ), VA and VAR Voltage and current waveforms
ement power
Voltage and current waveforms
True-rms voltage and current
Frequenc
y
Voltage, current, and power harmonics
Up to 51st harmonic
otal harmonic distortion (T
T
Phase angle of individual harmonics
HD)
Specifications
• Measurements are always automatically recorded to instantly show changes over time
• Use cursors to read time and date of sags and swells
• Catch voltage transients and waveform distortion down to 40 nS
• Catch and save up to 40 transients
• Correlate the cause of transients with time and date stamps
Accuracies are stated as ± (percentage of reading + counts) without probes unless
Specifications are valid for signals with a fundamental between 40 and 70 Hz.
otherwise noted.
Input Characteristics Ranges Accuracy
Input impedance 1 M, 20 pF Voltage rating 600 Vrms, CAT III
Volt/Amps/Hertz
True-rms voltage (AC+DC) 5.000 V, 50.00 V, 500.0 V, 1250 V* ± (1 % + 10 counts) True-rms current (AC+DC) 50.00 A, 500.0 A, 5.000 kA, 50.00 kA, 1250 kA ± (1 % + 10 counts) Frequency 10.0 Hz to 15.0 kHz ± (0.5 % + 2 counts) CF Crest Factor 1.0 to 10.0 ± (5 % + 1 count)
Power
W, VA, VAR Reactive Power 250 W 2.50 kW, 25.0 kW, 250kW, 2.50 MW, ± (2 % + 6 counts) Total Power 1-phase and 3-phase, 3 25 MW, 250 MW, 625 MW, 1.56 GW ± (4 % + 4 counts) Fundamental conductor balanced loads Power
PF Power Factor 0.00 to 1.00 ± 0.04 DPF Displacement Power Factor 0.00 to 0.25 not specified
Hz Frequency fundamental 40.0 to 70.0 Hz ± (0.5 % + 2 counts)
Harmonics
Volts, Amps, Watts Fundamental V, A ± (3 % + 2 counts),
Frequency of fundamental 40 Hz to 70 Hz ± 0.25 Hz Phase Volt & Amps (between Fund. & Harmonic) 2nd (± 3°) … 51st (± 15°)
K-Factor (Amps & Watts) 1.0 to 30.0 ± 10 % THD 0.00 to 99.99 ± (3% + 8 counts)
Sags & Swells
Recording times (selectable) 4 min to 16 days Vrms actual, Vrms max, 5.000 V, 50.00 V 500.0 V, 1250 V* Readings ± (2 % +10 counts)
min (AC + DC) Cursor readings ± (2 % + 12 counts)
Arms actual, Arms max, 50.00 A, 500.0 A, 5.000 kA, 50,00 kA min (AC + DC)
Recording
ording times (selectable)
Rec
arameters
P
V/A/Hz Line Voltage, Current, Frequency Power Watts, VA, VAR, PF, DPF, Frequency Harmonics THD, Volts (Fund. & Harmonic), Amps(F&H) Watts(F&H) Freq.(H), %(H) of total, Phase(H), KF Ohms Ohms, Diode, Continuity, Capacitance Temperature °C or °F Scope DC Voltage, DC Current, AC Voltage, AC Current, Frequency, Pulse Width + or -,
ansients
Tr
Minimum pulse w Useful bandw
er of transients
Numb
oltage threshold settings
V Referenc
Vpeak min, Vpeak max at cursor 10 V, 25 V, 50 V, 125 V, 250 V, 500 V, 1250 V ± 5 % of full scale
e sig
idth
idth input
nal
0.25 to 0.90 ± 0.04
0.90 to 1.00 ± 0.03
2 to 31st Harmonic V, A ± (5 % + 3 counts),
32 to 51st Harmonic V, A ± (15 % + 5 counts),
Watts (between Volt Fund. & Amps Harmonic ) Fund (± 5°) … 51st (± 15°)
6 days
4 min to 1 Choose one or two parameters from one of the g
eak min, P
Phase, Duty c
40 ns
C to 1 M
D 40 20 %, 50 %, 1 After S
data a pure sinewave is calculated as reference for threshold setting.
ycle + or -, P
Hz (w
00 %, 200 % ab
ART, the Vrms and frequency of the signal are measured. From these
T
eak max, P
ith test leads TL24)
ove or b
elow reference signal
W ± (5 % + 2 counts)
W ± (10 % + 10 counts)
W ± (30 % + 5 counts)
Cursor Readings Average ± (2 % +10 counts)
roups below
eak min-max, Crest F
actor
*Rated 600 V CAT II
Inrush Current Ranges Accuracy
Current ranges (selectable) 1 A, 5 A, 10 A, 50 A, 100 A, 500 A, 1000 A Inrush times (selectable) l s, 5 s, 10 s, 50 s, 100 s, 5 min Cursor readings A peak max at cursor 1 and cursor 2 ± 5 % of full scale Time between cursors** 4 to 235 pixels ± (0.2 % + 2 pixels)
Scope, dual channel scope with measurement reading
Input impedance Input 1 1 M/12 pF; with BB120: 20 pF ± 2 pF; with BB120 ± 3 pF Input 2 1 M/10 pF; with BB120: 18 pF ± 2 pF; with BB120 ± 3 pF
Vertical
Voltage ranges 50 mV/div to 500V/div ± (1% + 2 pixels) Vertical sensitivity, resolution 5 mV/div to 500V/div, 8 bit (256 levels) Bandwidth input 1 (voltage) DC to 20 MHz at inputs, or with VPS40 probe (Opt);
Bandwidth input 2 (current) DC to 15 kHz at inputs
Coupling DC, AC (10Hz (-3 dB)
Horizontal
TimeBase modes Normal, roll, single TimeBase ranges 60 s/div to 20 ns/div ± (0.4 % + 1 pixel) Sampling rate 25 MS/s Record length 512 per channel
(min / max samples) Trigger source Input 1 or Input 2 or Automatic selection Trigger mode Automatic Connect-and-View™, Free Run,
Connect-and-View™ Advanced automatic triggering that recognizes signal patterns and automatically
Pre-trigger Up to 10 divisions Measurement readings, Volts & Amps (DC, AC, AC + DCrms, Peak max, Peak min, Peak min / max ),
per channel selectable Frequency, Duty cycle + or - , Phase, Pulse Width + or -, Crest factor
Ohms, Diode, Continuity, Capacitance
Ohms 500.0
Diode voltage 0 to 3.000 V ± (2 % +5 counts) Continuity, shorts > 1 ms Beeper on at < 30 ±5 Ω, Capacitance 50.00 nF, 500.0 nF, 5.000 µF, 50.00 µF, ±(2 % +10 counts)
Temperature*** -100.0 °C to 400.0 °C, ±(0.5 % +5 counts)
Max current, max open circuit volt. 0.5 mA, < 4 V (all functions above)
Memory
Number of screens 20
Optical Isolated Interface
To printer Supports HP LaserJet™, DeskJet, Epson FX/LQ and Postscript printers with
To PC FlukeView®Power Quality Analyzer software with PM9080 Interface
FlukeView®Power Quality Software
Hardware requirements PC or 100 % compatible with Windows®95, 98, Me, 2000, NT4.0.
1 MHz with TL24 Leads
10 kHz with 80i-500s Current Clamp
Single Shot.
adjusts triggering, timebase and amplitude. Automatically displa of complex and dynamic signals like motor drive and control signals.
, 500.0 kΩ, ± (0.6 % +5 counts)
, 50.00 k
5.000 k
5.000 M, 30.00 M
500.0 µF
-200.0 °F to 800.0 °F
optional PAC91 Printer Adapter Cable
Adapter included
ys stable pictures
• Inrush current up to 500A with supplied current probe
• Use cursors to measure inrush current timing
• Connect-and-View™ scope for quick
veform displa
wa 20MHz bandwidth with optional 10:1 voltage
y
probe. 15kHz on current channel with optional current clamp
** 1 pixel = inrush time/250 *** Requires optional temperature accessory
FlukeView
®
ower Quality Analy
P
zer software
(included)
• Capture measurement screens for professional-looking reports
• Log readings to your computer disk drive
• Works with Windows word processing, spreadsheet and analysis software
• Window
s 95 / 98 / Me / 2000 / NT 4.0
General Specifications
43B POWER QUALITY ANALYZER
HOLD RUN
PRINT
ENTER
F1 F2 F3
RECORD
MENU
SAVE
12
Power
Line voltage adapter/battery charger included Installed battery Rechargeable NiMH pack (4.8v dc)
Operating time 4 hours Charging time 7 hours
Environmental
Temperature 0 ºC to 50 ºC (32 ºF to 122 ºF) Environmental MIL 28800E, Type 3, Class I II, Style B Enclosure IP51 (dust, drip water proof)
Mechanical Data
Size (H x W x D) 232 x 115 x 50 mm (9.1 x 4.5 x 2 inches) Weight 1.1 kg (2.5 lbs.) incl. battery pack
Safety
For measurements on 600 Vrms Category III installations, Pollution Degree 2 in accordance with E N 61010- 1 ANSI /ISA S82.01-1994 CAN/CSA-C22.2 No. 61010.1-04
Surge protection 6 kV on input 1 and 2 Floating measurements 600 Vrms from any terminal to ground
Warranty 3 years parts and labor on Fluke 43B, 1 year on accessories
Ordering Information
Fluke 43B Power Quality Analyzer
Included Accessories
C120 Hard Case TL24 Test Leads AC20 Industrial Test Clips AC85 Large Jaw Alligator Clips TP1 Flat-tipped Slim-Reach™ Test
TP4 4 mm Round Slim-Reach™
i400s 400 A AC Current Clamp
B
S
C4U
O
BP120MH Rechargeable NiMH Battery
PM8907 Line Voltage Adapter/Battery
W43W
S
er Quality CD with:
ow
P
User’s manual
• Power quality video
• Application guide
Getting started guide Shielded Banana-to-
es
Prob
es
est Prob
T
Optically Isolated U
S
Interface Adapter
Pack (installed)
Charger FlukeView®P
ower Quality Analyzer Software for Windows
BNC adapter
B
Optional Accessories
C789 Soft Carrying Case 80i-110s 100A AC/DC Current Probe i200s AC Current Clamp i1000s 1000A AC Current Clamp i2000flex Flexible 2000A AC Current
Probe
i3000s Clamp-On AC Current Clamp VPS40 10:1 Voltage Probe BB120 Two Shielded Banana-to-
BNC Adapters
80TK Thermocouple Module 80T-150U Universal Temperature Probe PAC91 Parallel Printer Adapter TLK225 SureGrip®Master Accessory
L220
T
63" T
TL221 Extension Lead Set TL223 Electrical Test Lead Set
Test Lead Kit
est L
ead Set
Fluke. Keeping your world
up and running.
Fluke Corporation
O Box 9
P Fluke Europe B.V.
PO Box 1186, 5602 BD Eindhoven, The N
For more information call: In the U.S.A. (800) 443-5853 or
ax (425) 446-5
F In Europe/M-East/Africa (31 40) 2 675 200 or
ax (31 40) 2 675 222
F In Canada (8 Fax (905) 890-6866 From other countries (425) 446-5500 or Fax (425) 446-5116 Web access: http://www.fluke.com/
©2005 Fluke Corporation Trademarks are the property of their respective owners. Printed in U.S.A. 11/2005 1266142 D-ENG-N Rev H
Printed on rec
0, Everett, W
9
0
00) 36-
ycled paper
etherlands
6
1
1
LUKE or
F
. All rights reser
.
A U
A 9820
S
ved
6
.
Loading...