Fluke 114, 115, 117 Data Sheet

Fluke 114, 115, 116 and 117

Digital Multimeters

Extended speciﬁcations

Technical Data

General speciﬁcations (all models)

Accuracy is speciﬁed for 1 year after calibration, at operating temperatures of 18 °C to 28 °C, with relative humidity of 0 % to 90 %.

Maximum voltage between any terminal and earth ground

Surge protection 6 kV peak per IEC 61010-1 600 V CAT III, Pollution Degree 2 W Fuse for A input 11 A, 1000 V FAST 17 kA Fuse (Fluke PN 803293) Display Digital: 6,000 counts, updates 4/sec; Bar Graph: 33 segments, updates 32/sec Temperature Operating: -10 °C to +50 °C; Storage: -40 °C to +60 °C Humidity 0 % to 90 % to 35 °C; 75 % to 40 °C; 45 % to 50 °C Temperature coefﬁcient 0.1 x (speciﬁed accuracy/°C) (< 18 °C or > 28 °C) Operating altitude 2,000 meters Battery 9 Volt Alkaline, NEDA 1604A/IEC 6LR61 Battery life Alkaline: 400 hours typical, without backlight Safety compliances ANSI/ISA 82.02.01 (61010-1) 2004, CAN/CSA C22.2 No 61010-1-04, UL 6101B (2003) and IEC/EN

Certiﬁcations UL, CSA, TUV, N10140 , VDE IP rating (dust and water protection) IP42

600 V

61010-1 2nd Edition for measurement Category III, 600 V, Pollution Degree 2, EMC EN61326-1

Accuracy speciﬁcations (all models)

Function Range Resolution

DC millivolts 600.0 mV 0.1 mV 0.5 % + 2 114, 115, 116, 117 DC volts 6.000 V

Auto-V LoZ1 true-rms 600.0 V 0.1 V 2.0 % + 3 4.0 % + 3 114, 116, 117

AC millivolts1 true-rms 600.0 mV 0.1 mV 1.0 % + 3 2.0 % + 3 114, 115, 116, 117 AC volts1 true-rms 6.000 V

Continuity

Ohms 600.0 W

Diode test 2.000 V 0.001 V 0.9 % + 2 115, 116, 117 Capacitance 1000 nF

LoZ capacitance (power-up option) 1 nF to 500 µF 10 % + 2 typical 115, 116, 117

All ac ranges except Auto-V LoZ are speciﬁed from 1 % to 100 % of range. Auto-V LoZ is speciﬁed from 0.0 V. Because inputs below 1 % of

range are not speciﬁed, it is normal for this and other true-rms meters to display non-zero readings when the test leads are disconnected from a circuit or are shorted together. For volts, crest factor of ≤ 3 at 4000 counts, decreasing linearly to 1.5 at full scale. For amps, crest factor of ≤ 3. AC volts is ac-coupled. Auto-V LoZ, ac mV, and ac amps are dc-coupled.

60.00 V

600.0 V

60.00 V

600.0 V 600 W 1 W

6.000 kW

60.00 kW

600.0 kW

6.000 MW

40.00 MW

10.00 µF

100.0 µF 9999 µF

0.001 V

0.01 V

0.1 V

0.001 V

0.01 V

0.1 V

0.1 W

0.001 kW

0.01 kW

0.1 kW

0.001 MW

0.01 MW

1 nF

0.01 µF

0.1 µF 1 µF

Accuracy ± ([% of Reading]

+ [Counts]) Model

0.5 % + 2 114, 115, 116, 117

DC, 45 Hz to

500 Hz

45 Hz to 500 Hz 500 Hz to 1 kHz

1.0 % + 3 2.0 % + 3 114, 115, 116, 117

Beeper on < 20 W, off > 250 W;

detects opens or shorts of

100 µF to 1000 µF: 1.9 % + 2

> 1000 µF: 5 % + 20

500 Hz to 1 kHz

500 µs or longer

0.9 % + 2

0.9 % + 1

1.5 % + 2

1.9 % + 2

114, 115, 116, 117

115, 116, 117

Accuracy speciﬁcations (all models) cont.

Function Range Resolution

Temperature (K-Type thermocouple) -40 °C to 400 °C

AC amps true-rms1 (45 Hz to 500 Hz) 6.000 A

-40 °F to 752 °F

10.00 A 20 A overload for 30 seconds maximum

0.1 °C

0.2 °F

0.001 A

0.01 A

Accuracy ± ([% of Reading]

+ [Counts]) Model

1 % + 10 1 % + 18

1.5 % + 3 115, 117

116

AC µAmps true-rms1 (45 Hz to 1 kHz) 600.0 µA 0.1 µA 1.5 % + 3 (2.5 % + 3 > 500 Hz) 116 DC amps 6.000 A

10.00 A 20 A overload for 30 seconds maximum

0.001 A

0.01 A

1.0 % + 3 115, 117

DC µAmps true-rms 600.0 µA 0.1 µA 1.0 % + 2 116 Hz (V or A input)

Hz (V input)

All ac ranges except Auto-V LoZ are speciﬁed from 1 % to 100 % of range. Auto-V LoZ is speciﬁed from 0.0 V. Because inputs below 1 % of range

are not speciﬁed, it is normal for this and other true-rms meters to display non-zero readings when the test leads are disconnected from a circuit or are shorted together. For volts, crest factor of ≤ 3 at 4000 counts, decreasing linearly to 1.5 at full scale. For amps, crest factor of ≤ 3. AC volts is ac-coupled. Auto-V LoZ, ac mV, and ac amps are dc-coupled.

AC Volts Hz is ac-coupled and speciﬁed from 5 Hz to 50 kHz. AC Amps Hz is dc-coupled and speciﬁed from 45 Hz to 5 kHz. Amps input burden

voltage (typical): 6 A input 2 mV/A, 10 A input 37 mV/A.

Frequency is ac-coupled, 45 Hz to 50 kHz.

99.99 Hz

999.9 Hz

9.999 kHz

50.00 kHz

99.99 Hz

999.9 Hz

9.999 kHz

50.00 kHz

0.01 Hz

0.1 Hz

0.001 kHz

0.01 kHz

0.01 Hz

0.1 Hz

0.001 kHz

0.01 kHz

0.1 % + 2 115, 117

0.1 % + 2 116

Frequency counter sensitivity (models 115, 116, 117)

Typical sensitivity (rms sine wave)

Input range 5 Hz to 45 Hz 45 Hz to 5 kHz 5 kHz to 10 kHz 10 kHz to 50 kHz

Volts AC 6 V

AC Amps (115, 117 only)

60 V

600 V

6 A

10 A

0.2 V 2 V

20 V

N/A N/A

0.2 V to 0.3 V 2 V to 3 V

20 V to 30 V

0.4 A

0.5 A

0.3 V to 0.4 V 3 V to 4 V

30 V to 40 V

N/A N/A

0.4 V to 1.0 V 4 V to 10 V

40 V to 100 V

N/A N/A

Input characteristics (all models)

Function

Volts AC > 5 MW < 100 pF > 60 dB at dc, 50 or 60 Hz

Volts DC > 10 MW < 100 pF > 100 dB at dc, 50 or 60 Hz > 60 dB at 50 or 60 Hz

Auto-V LoZ ~3 kW < 500 pF > 60 dB at dc, 50 or 60 Hz

Ohms < 2.7 V dc

Diode Test < 2.7 V dc 2.000 V dc < 1.2 mA

Input impedance

(nominal) Common mode rejection ratio(1 kW unbalanced) Normal mode rejection

Open circuit test voltage Full scale voltage Short circuit current

To 6.0 MW 40 MW

< 0.7 V dc < 0.9 V dc

Fluke. Keeping your world up and running.™

< 350 µA

For more information call: In the U.S.A. (800) 443-5853 or Fax (425) 446-5116 In Europe/M-East/Africa +31 (0) 40 2675 200 or

Fluke Corporation PO Box 9090, Everett, WA USA 98206

Fluke Europe B.V. PO Box 1186, 5602 BD Eindhoven, The Netherlands

Fax +31 (0) 40 2675 222 In Canada (800)-36-FLUKE or Fax (905) 890-6866 From other countries +1 (425) 446-5500 or Fax +1 (425) 446-5116 Web access: http://www.fluke.com

2 Fluke Corporation Fluke 11X Series Digital Multimeters Extended Speciﬁcations