Flir N437BEW, N437BDL Quick Start Guide
Quick Connection Guide
N437BEW / N437BDL SERIES
Network Bullet Camera
PACKAGE CONTENTS:
1 x IP Bullet Camera
4 x Mounting Screws
1 x RJ45 Waterproof Cap
1 x Star Key
4 x Drywall Anchors
1 x Mounting Template
1
A
B
C
D
Installing the Camera
Use the included mounting template to mark holes
for the screws.
Drill holes for the mounting screws.
NOTE: Use the included drywall anchors if installing
into drywall.
Connect cables as shown in the section “Connecting
the Camera”.
Mount the camera to the surface using the included
mounting screws (4x).
2
A
Adjusting the Camera
Use the included Star key to loosen the adjustment
screw on the camera stand. Tighten the adjustment
screw when finished.
1. Twist the camera to make sure picture is level.
2. Tilt the camera.
3. Rotate the camera base.
2
1
3
Adjustment screw
3
1. Power Input: If not using PoE, connect the camera to a 24V
AC power source (750mA or higher required).
2. Ethernet Port: Connect the camera to an NVR or a router or
switch on your network using Cat5e or better Ethernet cable
(not included). PoE Class 3 supported (802.3af).
NOTE: Install the included RJ45 waterproof cap if needed.
3. Alarm I/O: Connect alarm/sensor devices (not included).
4. Audio I/O: See the Instruction Manual for details.
Connecting the Camera
1
2
3 4
Quick Start Guides
1 x BNC Test Cable
Latest software and manuals available on
www.flir.com/security/support
For support, visit
www.flir.com/security/support
Information in this document is subject to change
without notice. As our products are subject to continuous
improvement, FLIR Systems, Inc. and our subsidiaries reserve
the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE © 2015 FLIR Systems, Inc. All rights reserved.
Drywall anchors (4x)
Mounting screws (4x)
Use the included Star key to remove the compartment cover.
A
1
2
1. Video Out: Connect a test monitor using the included BNC test
cable.
2. microSD Slot: Insert a microSD card (not included) into the slot.
3. Zoom Controls: Hold the joystick left / right to zoom out / in. The
camera will focus automatically.
4. Reset Button: Press and hold the button for 5 seconds using a
thin object to reset the camera to default settings.
5. Not supported. Service only.
Close the compartment cover and secure the screw when finished.
B
3
4
5
B
3.9” /
100mm
Remove the vinyl film from the camera lens once
installation is complete.
4.3” / 109mm
Weight
3.1lb / 1.4kg
10.6” /
268mm
NOTE: The camera has a default setting of 30/25fps.
60/50fps is supported. To use 60/50fps, make sure your
recording device supports this setting.
Safety PrecautionsWeights & DimensionsService Compartment
• Use an appropriate low voltage power cable to prevent fire or electrical
shock.
• Make sure to install the camera in an area that can support the camera
weight.
• There are no user serviceable parts inside the camera. Please do not
disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning material. Please use
a lint free micro-fiber cloth to clean the lens cover.
• Camera is rated for outdoor use (IP66), but is not intended for submersion
in water.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
N437BEW_N437BDL_SERIES_QCG_EN_R2
Loading...