FLIR N347VW4 SERIES Quick Start Manual

flir.com/security/pro

6.3”
159mm

MODEL: N347VW4

SERIES

QUICK START GUIDE

English Version 2.0

FLIR Systems, Inc., Copyright © 2017
As our products are subject to continuous improvement, FLIR Systems
Inc. reserves the right to modify product design, specifications and
prices, without notice and without incurring any obligation. E&OE

flir.com/security/pro

VISIT

Compatible Accessories

IT’S ALL ON THE WEB!

FCC Notice

This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

N347VW4_QSG_EN_R2

This security camera has several mounting options:

Safety Precautions

• Use an appropriate low-voltage power cable to prevent fire
or electrical shock.

• Make sure to install the camera in an area that can support
the camera weight.

• There are no user-serviceable parts inside the camera. Do
not disassemble the camera.

• Do not clean the lens cover with an abrasive cleaning
material. Use a soft cloth to clean the lens cover.

• Camera is rated for outdoor use (IP66), but is not intended
for submersion in water.

• Extend the Ethernet-cable run for your camera up to
300ft. You can use an RJ45 coupler or network switch to
connect male ends of Ethernet cable together. A maximum
of 3 connections is recommended.

Weights & Dimensions

4.7”
118mm

2.0lbs / 0.9kg

Weight

Accessories Model Numbers

Junction Box S4JF6G*

Wall Mount S6WF1G

Pendant Cap S6PCF1G

Pole Mounts S4PA2G with S6WF1G, or

S1PA2G with S6CF1G

Corner Mounts S1RA2G with S6WF1G

Ceiling Mount S6CF1G

4MP Motorized Varifocal

Network Vandal Dome Camera

Adjusting Zoom and Focus

1

2

Adjust the camera’s zoom and focus using an NVR or the web
interface. For more information, see your NVR’s instruction
manual on www.flir.com/security/pro.

NVR: Right-click on the camera’s live view and then
click AutoFocus. Use the sliders to adjust the zoom and
focus.

Web Interface: Use the controls in the right-hand panel
to adjust the zoom and focus.

3

Manual Zoom In/Out: Located on the camera base, press
W to zoom out and T to zoom in.

*Required for conduit installation.

6.3” / 159mm

Package Contents

• 1× 4MP Network Vandal Dome Camera

• 3× Mounting Screws & Drywall Anchors

• 1× Security Screwdriver

• 1× Mounting Template

Use the included security screw driver to loosen the
dome cover screws (3×). Remove the dome cover.

ATTENTION:

Test the camera prior to selecting a permanent mounting location by
temporarily connecting the camera(s) and cables to the NVR.

Installing the Camera

1

Use the included mounting template to mark holes for
the mounting screws.

2
3

4

5

6

7

Drill holes for the mounting screws. Use the included
drywall anchors if needed.

Connect the cables. See “Camera Connections Overview”
section for details. To ensure weatherproof installation,
when you are running the cable through the cable
conduit:

Attach the camera base to the mounting surface using
the included mounting screws (3×).

Mounting
screws (3×)

Drywall
anchors (3×)

Set the position and angle of the camera:

A) Rotate the camera around the base (rotates 360°
maximum).

B) Use a Phillips screwdriver to loosen the tilt
adjustment screws (2×). Tilt the camera. Tighten
both screws when finished.

C) Adjust the position of the camera lens by twisting.

A

B

C

Replace the dome cover. Use the included security
screw driver to tighten the dome cover screws (3×).

ATTENTION:

Make sure IR LEDs are not blocked by the dome cover to prevent IR
reflection.

8

Remove the vinyl film from the dome cover.

Camera base

Camera Overview

A. IR LEDs
B. Light Sensor
C. Tilt Adjustment Screws (2×)
D. Reset Button: See “Resetting

the Camera” section for details.
E. microSD Card Slot: See

“Inserting the microSD Card”
section for details.

F. Manual Zoom In/Out: See
“Adjusting Zoom and Focus”
section for details.

Tilt Adjustment
screws (2×)

Reset
button

Resetting the Camera

1

2

Remove the dome cover. Make
sure the camera is powered on.

Press and hold the reset
button for 5 seconds
using a thin object to
reset the camera to
default settings.

Inserting the microSD Card

1

2

Remove the dome cover.

Insert the microSD card
(not included) into the slot
until you hear a click.

microSD slot

NOTE: For details on configuring microSD recording, see

the FLIR IP Series Instruction Manual on this camera’s
product page at www.flir.com/security/pro.

For local recording, you can install a microSD card up to 128GB.
SanDisk™ or Kingston™ brand microSD cards recommended.
microSD card Class 10 supported.

L. Dome Cover
M. Dome Cover Screws (3×)

N347VW4_QSG_EN_R2

A

B

C

D

E

F

H

J

K

G. Analog Video Out (RCA)
H. Audio I/O and Alarm

I/O Block

I. Cable Conduits (2×)
J. Ethernet Port (PoE):

PoE supported
(802.3af).

K. 12VDC / 24VAC Power
Input

L

M

I

A) Remove the cable conduit cap.
B) Run the cable through the cap.
C) Insert the cap back into the cable conduit. Use

silicone as needed.

G

Camera Connections Overview

Analog
Video Out

Audio
Output

Audio
Input

Audio
(GND)

Alarm
Output

Alarm
(GND)

Alarm
Input

Ethernet
Port (PoE)

12VDC/24VAC
Power (+)

12VDC/24VAC
Power (-)

NOTE: Use junction box model S4JF6G for conduit

installation.

J

Use either of the two cable conduits to run cables through the
camera base.

K

H

G

NOTE: See “Camera Overview” section for details.

* If not using PoE, connect the camera to a 12VDC/24VAC
power source. See the rating label on the camera for
minimum power requirements.

*