Flir N336ZD1 User Manual
Quick Connection Guide
N336ZD1
2.1MP HD Dome PTZ IP Camera
PACKAGE CONTENTS:
1 x IP PTZ Camera
4 x Mounting Bolt Set
1 x Insulated Glove
Quick Start Guides
1 x Wall Bracket
1 x 24V AC Adapter
1 x Allen Key
1 x CD
1
A
B
C
D
Installing the Camera
Loosen the dome cover
screws (3x) using the included
Allen key and remove the
dome cover from the camera.
Remove the foam ring around
the camera module. Replace
the dome cover and tighten
the dome cover screws.
Use the wall mount to mark holes for the
mounting bolts (4x) and connection cable. Drill
holes in the wall.
Loosen the M3x6 screw (1x)
on the wall bracket. Attach the
bracket connector to the wall
bracket so that it is flush with the
wall bracket. Tighten the M3x6
screw (1x) to
secure the
bracket connector.
Run the cables from the camera
through the wall bracket. Insert
the camera until it is flush with the bracket connector
and then tighten the allen bolts (3x) to secure the camera.
Foam ring
Wall bracket
Bracket connector
2
E
F
Mounting Bolts (4x)
G
Installing the Camera (Continued)
Place the anchors (4x) on the mounting bolts (4x) with the
expandable side on the wide end of the bolt. Insert the wide end
of the mounting bolt assembly into the wall and tap the bolts
into the wall with a hammer.
Run the connection cable through the surface and wall mount.
Place the wall mount over the mounting bolts and attach the
wall mount to the wall by screwing a flat washer (4x), spring
washer (4x), and nut (4x) on each bolt.
Anchors (4x)
Remove the vinyl film from the dome cover once installation is
complete.
Wide end of bolt
(insert into wall)
Flat Washer (4x)
Spring Washer (4x)
Nut (4x)
Expandable side of anchor
(place over wide end of bolt)
3
Connecting the Camera
4
1
3
2
1. Alarm I/O: Connect the camera to up to 2 alarm input devices
and 1 alarm output device. See the Instruction Manual on CD
for more details.
2. Audio I/O: Connect to a self-powered microphone for
listen-in audio, or to an audio output device (e.g., speakers).
3. Ethernet Port: Connect the camera to an NVR or a router or
switch on your network using Cat5e or better Ethernet cable
(not included). PoE Class 4 supported.
4. Power Input: If not using PoE, connect the camera to a 24V
AC power source (1.5A or higher required).
Latest software and manuals available on
www.flirsecurity.com/pro
For support, visit
www.flirsecurity.com/pro
Information in this document is subject to change
without notice. As our products are subject to continuous
improvement, FLIR Systems, Inc. and our subsidiaries reserve
the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE © 2014 FLIR Systems, Inc. All rights reserved.
7.3” / 186mm
9.3” /
235mm
5.0lbs / 2.3kg
Camera Only
Weights & Dimensions
10.2” / 259mm
Weight
6.2lbs / 2.8kg
Camera with Wall-Mount
16.4” /
419mm
Inserting the microSD Card (Optional)
For local recording, you can install a microSD card in the camera (up to 64GB).
SanDisk™ Extreme brand microSD cards are recommended for demanding 24/7
surveillance applications.
Loosen the dome cover screws (3x) and remove the
A
dome cover.
Insert a microSD card into the microSD card
B
slot with the back of the card facing the
camera lens. Replace the dome cover and
tighten the dome cover screws (3x).
NOTE: For details on configuring microSD
recording, see the Instruction Manual on the web.
microSD slot
Resetting the Camera
Loosen the dome cover screws (3x) and
A
remove the dome cover.
Press the reset button for 10 seconds
B
to reset the camera to default
settings. Replace the dome cover and
tighten the dome cover screws (3x).
Reset button
Safety Precautions
• Use an appropriate low voltage power cable to prevent fire or electrical
shock.
• Make sure to install the camera in an area that can support the camera
weight.
• There are no user serviceable parts inside the camera. Please do not
disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning material. Please use
a lint free micro-fiber cloth to clean the lens cover.
• Camera is rated for outdoor use (IP66), but is not intended for submersion
in water.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
N336ZD1_QCG_EN_R1
Loading...