Flir N233ZD User Manual
Quick Connection Guide
N233ZD
2.1MP HD IP Micro PT Camera
PACKAGE CONTENTS:
1x Micro PT IP Camera
3x Mounting Screws
1x Mounting Plate
Quick Start Guides
1x Allen Key
3x Drywall Anchors
1x Mounting Template
1x CD
1
A
Installing the Camera
Use the included mounting template to mark holes for the
mounting screws and camera cable.
Drill holes for the mounting screws and camera cable.
B
NOTE: Use the included drywall anchors if installing on a drywall
surface.
Align the metal mounting plate so that the 3 screw holes in the
plate line up with the 3 holes drilled in the wall.
C
Attach the flat side of the mounting plate to the surface using the
D
included mounting screws (3x).
Mounting surface
Drywall anchors (3x)
Mounting screws (3x)
Remove the M2x5 screw from the side of the camera using the
E
included Allen key.
M2x5 screw
Mounting plate
2
F
G
H
Pegs (x3)
I
J
Installing the Camera (continued) Connecting the Camera
Ensure the camera is grounded with the
pre-inserted M2x5 screw.
GND port
Connect cables as shown in the section “Connecting the Camera”.
Align the 3 notches on the side of the dome camera with the
3 corresponding pegs on the mounting plate. Push the camera
gently into the mounting plate until you hear a ‘click‘.
NOTE: The pegs and notches only align one way. Do not force
the camera to fit into the mounting plate.
Re-insert the M2x5 screw removed in Step E. Tighten firmly using
the included Allen key.
Remove the vinyl film from the camera lens once installation is
complete.
3
Notches (x3)
1
2
1. Ethernet Port: Connect the camera to an NVR or a router or
switch on your network using Cat5e or better Ethernet cable
(not included). PoE Class 3 supported.
2. Power Input: If not using PoE, connect the camera to a 12V
DC power source (300mA or higher required).
Latest software and manuals available on
www.flirsecurity.com/pro
For support, visit
www.flirsecurity.com/pro
Information in this document is subject to change
without notice. As our products are subject to continuous
improvement, FLIR Systems, Inc. and our subsidiaries reserve
the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE © 2014 FLIR Systems, Inc. All rights reserved.
Weight
0.6lbs / 0.3kg
2.3” /
58mm
5.1” /
130mm
Inserting the microSD Card
Separate the camera from the mounting plate if needed.
A
Remove the 2 screws from the compartment
B
cover using a Phillips screwdriver (not included).
Slide the microSD carriage cover to open, then
lift upward.
C
Place a microSD card (not included) into the
D
carriage with the metal contacts facing down.
Close and lock the carriage cover. Replace the
E
compartment cover on the camera base.
Resetting the Camera
Separate the camera from the mounting plate
if needed.
A
Remove the 2 screws from the compartment
B
cover using a Phillips screwdriver (not included).
Press and hold the reset button for 4 seconds.
C
Replace the compartment cover on the
D
camera base.
OPEN
LOCK
OPEN
Reset button
Safety PrecautionsWeights & Dimensions
• Use an appropriate low voltage power cable to prevent fire or electrical
shock.
• Make sure to install the camera in an area that can support the camera
weight.
• There are no user serviceable parts inside the camera. Please do not
disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning material. Please use
LOCK
a lint free micro-fiber cloth to clean the lens cover.
• Camera is rated for outdoor use (IP66), but is not intended for submersion
in water.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
N233ZD_QCG_EN_R1
Loading...