Flir MNTZX1PB User Manual
MNTZX1PB
IP66 Outdoor Power Box
Installation
Package Contents
Power Box 1pcs Rubber Plug 1pcs Waterproof
Hex Screw M6x25 4pcs
Spring Washer 4pcs
Small Flat Washer 4pcs
Mounting Bolt M8x55 4pcs
Anchor 4pcs
Anchor Cap 4pcs
Large Flat Washer 4pcs
Power Box Overview
1 Mounting plate
2 Bottom cover
3 Top cover
4 Electrical safety cover
5 Rail
6 Loop buckle
7 Shaft
8 M20 conduit cap
9 M6 screw
10 Gasket
11 M20 gasket
12 Rubber plug
13
14 Retaining ring
Cap 3pcs
Allen Key 1pcs
Waterproof lm
Make sure to install the product in an area that can support the
weight of the power box plus cameras and accessories.
Make sure to seal the box and all cable entrances according to
the instructions in this document.
Check www.irsecurity.com/pro for the latest compatibility list.
Loosen M6 screws (x2) on the left side of the top panel and open the power
1
box. Loosen the M6 screws (x2) inside the power box and remove the
mounting plate.
Bottom cover
Mounting plate
M6 screws inside power box (x2)
Use the mounting plate to mark holes for the mounting bolts (x4) and any
2
cables you are running through the mounting surface. Use outer holes to
mount power box to wall.
UP arrow on mounting plate should
be pointed up and away from the
mounting surface.
You must leave at least 30mm of
clearance from all sides of the
mounting plate to leave space to
install the power box.
Dimensions (units: mm)
Weight (power box only): 1.7Kg / 3.7lbs
NOTE: If installing power box on corner mount or pole mount, attach mounting
plate to the mount using the bolts supplied with the corner or pole mount. Skip
to step 5. Illustrations of complete installation shown below.
Drill holes for the mounting bolts (x4) and cables. Insert the anchors (x4)
3
and anchor caps (x4) into the holes as shown below. Run cables through
the mounting surface.
Anchor and
anchor cap (x4)
www.irsecurity.com/pro
MNTZX1PB_INSTALLATION_DIAGRAM_EN_R1
Place the mounting plate over the holes. Insert the mounting bolts (x4) and
4
large at washers (x4) to secure the mounting plate to the mounting
surface.
Mouting bolt and
large at washer (x4)
Run cables through rear M20 gaskets or bottom conduit holes.
5
Run the required cabling for the camera through the rubber plug on the top
7
cover of the power box.
Rubber plug
Install any required equipment inside the power box. Install the mount (not
8
included) and camera (not included) to the front of the power box with the
hex screws (x4), spring washer (x4), and small at washers (x4).
The below images show examples of items that can be installed to the power
box. All items below are not included with power box. Check www.irsecurity.com/pro for the latest compatibility list.
Follow all instructions below. Incorrect installation of cables may impact
the weatherproof rating of the power box.
To run cables through rear M20 gaskets:
1. Poke a hole in the gasket with a nail or pin.
2. Run the cable through the gasket.
3. Attach the connector to the cable on the inside of the gasket.
Connector
Gasket
Cable
You must install the connector after pushing the cable through the gasket.
You cannot push nished cables through the gaskets. The diameter of
cables run through the gaskets must be between 3.5mm and 12mm.
To run cables through bottom conduit holes:
1. Run cable without through the weatherproof cap.
2. Screw weatherproof cap into one of the bottom conduit ports.
3. Attach connector to cable inside power box.
Hex screw, spring
washer, and small
at washer (x4)
Lightning
protection
module
Heater
module
NOTE: Width of the rail is 35mm.
Push the top cover up about 2mm and then close the power box. Tighten
9
the M6 screw (x4) on the front of the power box to secure the top cover and
seal the power box.
Push up to close
top cover
Power
module
Air switch
M6 screw (x4)
NOTE: Bottom conduit
diameter is M20-P1.5.
Cable
Weatherproof cap
Place the power box over the mounting plate and slide into place. Tighten
6
the M6 screws (x2) inside the power box to secure it to the mounting plate.
Bottom cover
Mounting plate
M6 screws inside power box (x2)
Loading...