Flir C237EC Quick Start Guide
On-Screen Display (OSD) Menu
Package Contents
Configure OSD menu options using the
integrated control stick on the camera
cable (see image to the right).
To use the OSD menu:
• OPTIONAL: Connect a test monitor to the
camera’s analog (yellow) BNC connector.
• Push the middle of the joystick to open the
OSD menu.
• Move the joystick / to select a setting,
then / to change the setting value.
• Push the middle of the joystick to confirm selection.
• Arrows beside settings indicate a submenu ( ).
Select the setting and push the joystick to enter.
• Select RETURN and push the joystick to return to the
previous menu, or EXIT from the main menu to exit.
See the full OSD menu tree below. For detailed
explanation of camera settings, see the OSD
instruction manual on www.flirsecurity.com/pro.
Language
Video Format
Backlight
DNR
Advanced Lens ELC
Version
Exit
OFF
WDR
BLC
HLC
ALC
Exposure
White Balance
Day&Night
Image
Special Black Level
Reset
Brightness
Shutter
Sens-Up
AGC
Auto
ATW
Preset
Manual
Mode
Delay
D N Level
N D Level
Smart IR
Smart IR Level
Sharpness
Color Gain
Freeze
Flip
D-Zoom
Defog
Privacy
DP Comp
• 1x 1.3MP Motorized Varifocal Lens WDR Dome
Camera
• 4x Mounting Screws
• 4x Drywall Anchors
• 1x Allen Key
• 1x Mounting Template
NOTE: 12V DC / 24V AC power supply not included.
Safety Precautions
• Use an appropriate low voltage power cable to
prevent fire or electrical shock.
• Make sure to install the camera in an area that can
support the camera weight.
• There are no user serviceable parts inside the
camera. Please do not disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning
material. Please use a soft cloth to clean the lens
cover.
IT’S ALL ON THE WEB!
VISIT
www.flirsecurity.com/pro
FLIR Systems, Inc., Copyright © 2015
As our products are subject to continuous improvement, FLIR
Systems Inc. reserves the right to modify product design,
specifications and prices, without notice and without incurring
any obligation. E&OE
1.3MP Motorized Varifocal Lens
QUICK START GUIDE
English Version 2.0
www.flirsecurity.com/pro
WDR Dome Camera
MODEL: C237EC/
C237ECP
Installing the Camera
ATTENTION:
Test the camera prior to selecting a permanent
mounting location by temporarily connecting the
camera(s) and cables to the DVR.
To install the camera:
1. Use the included Allen key to
loosen the security screw on the
dome cover.
2. Rotate the camera base counter-clockwise to separate
it from the ball camera and dome cover.
3. Use the included mounting template to mark and drill
holes for the included mounting screws.
NOTE: Insert the included drywall anchors if installing into
drywall.
4. Feed the camera cable through the camera base.
5. Connect the video and power cable as detailed in the
section ‘Setting up the Camera’.
6. Attach the camera base to the mounting surface using
the included screws.
7. Position the dome cover over the ball camera and twist
clockwise onto the camera base. Do not tighten completely.
8. Move the ball camera to the desired position. While
holding the ball camera in place, twist the dome cover the
rest of the way to secure it to the camera base. Holding
the camera prevents it from moving while tightening the
dome cover.
Setting up the Camera
1. Connect one of the two BNC connectors on the camera to the
video cable. See “Camera Wiring” for details.
2. Connect a power source to the power terminal block. The
camera supports both 12V DC and 24V AC power supplies.
NOTE: Make sure to follow correct polarity as marked on the
power connector. For AC power, connect multiple cameras using
consistent wiring polarity to prevent video rolling.
A REGULATED 12V DC or 24V AC power supply is REQUIRED for
use with this camera. Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.
WARNING:
Adjusting Zoom & Focus
Hold the joystick on the camera cable / to zoom in / out.
The camera will focus itself automatically.
NOTE: You can also adjust zoom and focus remotely if the
camera is connected to a FLIR MPX DVR using the MPX
video connector. See your MPX DVR’s instruction manual
for details.
Camera Wiring
Connect to a
12V DC or 24V AC
power supply.*
Analog
MPX
MPX
Connect to an MPX DVR for
720p viewing / recording.
* Camera focus may be affected if the power connection is too
long. It is recommended not to extend the power connection
past 200ft (61m).
Analog
Connect to an analog DVR for
960H viewing / recording.
Extension Cable Options
Camera Specifications
Image Sensor
Video Format
Effective Pixels
Resolution
Scan System
Sync System
S / N Ratio
Iris
AES Shutter Speed
Min. Illumination
Video Output
Lens Focal Length / Type
FOV (Horizontal)
Termination
IR Range / Qty.
Power Requirement
Power Consumption
Operating Temp. Range
Environmental Rating
Dimensions (W x H)
Weight
1/3” 1.3MP CMOS
NTSC (C237EC)/PAL (C237ECP)
H: 1305 V: 1049
Digital: 720p
Analog: 960H
Progressive
Internal
≥ 50dB (AGC Off)
AES
1/60 (1/50) ~ 1/60,000 sec.
0.1 LUX (IR Off)
0 LUX (IR LEDs On)
Digital: 720p MPX HD-CVI
Analog: Composite 1.0Vpp @ 75ohm
2.8-12mm F1.4 / Varifocal
Digital: 30-80°
Analog: 30-80°
BNC Type
100ft / 30m; 36 IR LED’s
12V DC ± 10%
24V AC ± 10%
12V DC: 740mA MAX with IR LED
24V AC: 465mA MAX with IR LED
–22° ~ 140°F / –30° ~ 60°C
IP66
4.7” x 3.9”
120mm x 99mm
1.4lbs / 0.6kg
Camera Dimensions
9. Use the included
Allen key to tighten
the security screw
on the dome cover.
Mounting
Surface
Camera Base
Ball Camera
Dome Cover
4 pcs
The entire length of the cable run must be made using a single
extension cable between the camera and the DVR.
Specification Maximum Length
RG59 20AWG Conductor 95% Braid
CSA/UL or C(UL) Approved
RG6 20AWG Conductor 95% Braid
CSA/UL or C(UL) Approved
Analog CCTV Balun Up to 300ft (91m)
† Long cable runs over 1000ft (300m) may be affected by
electro-mechanical interference (EMI), which can increase the
amount of noise in the picture in some installations.
Up to 1500ft (455m)
Up to 2300ft (700m)
†
†
3.9”
99mm
4.7” / 120mm
Loading...