Fisher-Price W9858 Instruction Sheet

Visit service.fisher-price.com

for assembly video

Please keep this instruction sheet for future reference,

as it contains important information.

Requires three “C” (LR14) alkaline batteries (not included) for operation.

Adult assembly is required. Tool required: Phillips screwdriver (not included).

Wipe this toy with a clean, damp cloth. Do not immerse.

This toy has no consumer serviceable parts. Do not take apart.

fisher-price.com

Assembled Parts

CAUTION

This package contains small parts. For adult assembly only.

Chute

Inflatable Ball

2 Ramp Walls

Arch Spinner

(Front and Back)

Round Base

Ramp Spinner

Trampoline Disk

2 Bases

(Left and Right)

Arch

Connector

Trampoline Base

(Left and Right)

Gate

2 Ramp Connectors

(Front and Back)

Gate Post Outer Post

Gate Frame

Assembled Parts

Arch

8 Curved Ramps (all different)

Base Ramp

Upper Ramp

Arch Post

Center Post

Hint: We recommend installing

the batteries before beginning the assembly of this toy. The battery

compartment is located on the bottom side of the center post.

#8 x ¾" (1,9 cm) Screw – 35

SHOWN ACTUAL SIZE

Tighten and loosen all screws

with a Phillips screwdriver.

Do not over-tighten.

Battery Installation

1,5V x 3

“C” (LR14)

Hint: We recommend alkaline batteries

for longer battery life.

Center Post

• Locate the battery compartment on the bottom of the center post.

• Loosen the screws in the battery compartment door with a Phillips screwdriver and remove the door.

• Insert three “C” (LR14) alkaline batteries.

• Replace the battery compartment door and tighten the screws. Do not over-tighten.

• If this toy begins to operate erratically, you may need to reset the electronics. Slide the power/volume switch off and back on.

• When sounds or lights become faint or stop, it’s time for an adult to change the batteries.

• Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities.

Battery Safety Information

In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:

• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.

• Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may explode or leak.

• Never short-circuit the battery terminals.

• Use only batteries of the same or equivalent type, as recommended.

• Do not charge non-rechargeable batteries.

• Remove rechargeable batteries from the product before charging.

• If removable, rechargeable batteries are used, they are only to be charged under adult supervision.

Assembly

Base

Center Post

• Fit a base onto the bottom of the center post.

Hint: Each base is designed to ﬁ t one way. If it does not seem to ﬁ t, try the other base.

• Insert three screws into the holes in the base and tighten.

• Repeat this procedure to assemble the other base to the center post.

• Turn the assembly upright.

Assembly

Gate Post

• Fit the gate post into the socket in the base assembly A.

Hint: If the gate post does not seem to ﬁ t, try the other socket in the base assembly.

• Turn the gate post B and then push down C to “snap” it in place. Pull up on the gate post to be sure it is secure.

• Fit the long end of the gate frame into the connector on the center post.

• Insert a screw into the center post connector and tighten.

Gate Frame

Assembly

• “Snap” the free end of the gate frame into the top of the gate post. Pull up on the gate frame to be sure it is secure.

Gate Door

Smiling Face

Inner

Groove

Outer

Groove

• Position the gate door with the smiling face upright.

• First, ﬁ t the inner groove on the gate door to the gate post.

• Next, wrap the outer groove around the gate post. Hold the gate assembly in place.

Assembly

• Insert two screws into the gate door and tighten.

Trampoline Base

Trampoline Disk

• Fit the trampoline disk into the slots in one of the trampoline bases.

• With the disk tilted toward the center post, ﬁ t the trampoline assembly to the gate frame.

Assembly

• Fit the remaining trampoline base to the door frame, trampoline disk and trampoline base.

• To hold the trampoline assembly in place, ﬁ rst insert a screw into the top center hole and tighten A.

• Insert three more screws into the trampoline assembly and tighten B.

Assembly

Arch Post

• Fit the arch post into the remaining socket in the base assembly A.

• Turn the arch post B and then push down C to “snap” it in place. Pull up on the arch post to be sure it is secure.

+ 22 hidden pages