Fisher & Paykel CMOTTK30, MOTTK30 Installation manual

MODEL CMOTTK30 CONVECTION MICROWAVE TRIM KIT

INSTALLATION INSTRUCTIONS

Before you begin, read these instructions completely and carefully.

Getting Started

Remove packaging

Contents Tools Required

Part Description Qty

Trim Assembly 1

Base 1

Rear Duct 1

Forward Duct 1

Foam Tape 2 ft

Mounting Bracket (L/R) 2

Sheet Metal Screws 14

1/8” Drill

#2 Phillip Screwdriver

Before installing trim kit, install the convection duct as follows:

1. Insert the rear section of the duct into the forward section of the duct and install 4 screws
supplied (Fig. 01).

2. Install foam tape on 2 anges of the rear section of the duct (Fig. 02).

3. Remove and retain the 2 top screws, left and right, located at the rear vertical edges
of the Microwave (Fig. 03).

4. Place the duct on top of the Microwave and reinsert the 2 screws removed in Step 3 (Fig. 04).

4 Screws

Fig. 01

Fig. 03

Foam Tape

Foam
Tape

Fig. 02

Fig. 04

Installing T rim Kit

1/16"

1. Cut opening in the cabinet face per the following dimensions:

Height: 19-3/16” + 1/16”, –0
Width: 25-3/4” + 1/16”, –0

Note: Refer to diagram on the following page.

The minimum cabinet depth is 20”.

When installing the Microwave and Trim Kit in
combination with a Wall Oven or Warming Drawer,
please follow the recommendations in the Microwave
Installation/ Use & Care Manual.

2. Add adequate platform base support in the bottom
of the cabinet for trim kit base to rest on.

3. Mark a centerline on the front edge of the cabinet bottom
(Fig. 05).

4. Place trim kit base and align centerline mark to the
triangular notch on the front edge

of the base (Fig. 06).

Fig. 05

5. Drill 1/8”
template and install a screw through the base into the
cabinet to prevent the base from shifting (Fig. 07).

6. Insert Microwave into opening on top of the base.
The
for correct alignment. The Microwave should be
in at this point.

7. Place the right and left mounting bracket supports by
resting the
of the cutout
should clear the
(see Fig. 09). Install top screws into the cabinet face by first
drilling 1/8”

8. Install trim kit face by inserting top pins of trim into
corresponding sockets on the top corners of clip support
plates (see insert 1).

9. Finish the
the
(see insert 3).

pilot holes in the cabinet using the base as a

Microwave feet should sit in the recesses on the base

plugged

bottom edges of the supports on the bottom

(Fig. 08). The long flange on the side supports

side of the cutout by approximately 1/16”

pilot holes (see inserts 3 and 4).

assembly by inserting the bottom pins into

corresponding sockets on front edge of the base

Check for proper door opening clearances.

Fig. 06

Fig. 07

Bracket
Support
on the
bottom
of cutout

Fig. 09

Fig. 08

REAR

CABINET

SCREW HOLE

INSERT 4

FORWARD

CONVECTION

DUCT

TRIM KIT
ASSEMBLY

FOAM TAPE ON
THIS FLANGE

MOUNTING

BRACKET
SUPPORT

CONVECTION

DUCT

FOAM TAPE ON
THIS FLANGE

25 3/4"+1/16"-0

FOAM TAPE ON
THIS FLANGE

HORIZONTAL CLIP

ORIENTATION

ON MOUNTING

"

1/8" HOLE FOR
MOUNTING
SCREW

CENTER
LINE

BRACKET

TOP PIN

OF TRIM

20 1/2”

BOTTOM PIN OF TRIM

INSERT 3

Stainless Steel Care

29 11/16”

FLANGE

TRIANGULAR

1 1/2”

SCREW HOLE

Note: when installed, the trim assembly is positioned
symmetrically over the cabinet cut-out

TOP SCREW

LOCATE MOUNTING BRACKET
IN BOTTOM CORNERS
OF CUTOUT

CENTERING
NOTCH

BASE

CABINET CUT-OUT:
19 3/16" +1/16" -0"

HORIZONTAL
CLIP ORIENTATION
ON BASE

INSERT 1

INSERT 2

This Trim Kit is made of stainless steel. Use the mildest cleaning procedure first.

Start with hot soapy water,
rinse and dry. If the trim kit has food soil remaining, try a general kitchen cleaner, such as Fantastik®,
Simple Green® or Formula 409®. Apply cleaner with a damp sponge,
Always scrub lightly in the direction of the grain. Do not use a steel wool
To touch up noticeable scratches in the stainless steel, sand very lightly with dry 100

rinse thoroughly and dry.

pad, it will scratch the surface.

grit emery paper,

rubbing in the direction of the grain. After cleaning use a stainless steel polish, such as Stainless Steel

Magic®.

5800 Skylab Road, Huntington Beach, CA 92647
Tel: [phone] • Fax: [phone]
Customer Service: 888.936.7872
www.fisherpaykel.com

241185D 01/18