Installation Instructions
NZ, AU Installation Information
BI452 series
Built-In Compact
BI602 series
Built-In Oven
Oven
BI602CTE series
Built-In Oven/Cooktop combination
BI602ED series
Built-In Double
Oven
BI602XC series
Built-In Oven/
Microwave
combination
541768C 10.2004 NZ
Warnings and Safety information
Before you start
WARNING!
Cut Hazard
Take care - panel
edges are sharp.
Failure to use caution
could result in minor
injury or cuts.
CAUTION!
In order to avoid hazard these products
Please follow installation information
Failure to install the product correctly
The product is to be installed only by an
must be installed according to these
instructions.
carefully. If in doubt consult your local
building authority by-laws.
could invalidate any warranty or liability
claims.
authorised person.
IMPORTANT!
Please make this information available to
the person responsible for installing the
product as it could reduce your installation
costs.
The cavity must be a completely sealed
box with no gaps. This will ensure the
cooling air flows under the product and
through the oven frame to give the correct
venting and cooling for the oven and
cabinet surround. Failure to seal cavity
box may cause distortion of surrounding
cabinetry.
Read these instructions carefully before
installing or using this product.
Ensure a suitable disconnection switch
is incorporated in the permanent wiring,
mounted and positioned to comply with
the local wiring rules and regulations. A
means of disconnection with at least a
3mm air gap contact separation in all poles
must be incorporated into the fixed wiring
in accordance with the wiring rules, unless
the local wiring rules allow for the following
variation. A means of disconnection from
the supply having an air gap separation
in all active (phase) conductors must be
incorporated in to the fixed wiring.
Ensure that the location of the oven
connection socket is outside the installation
space if the product is flush to the rear wall.
Ensure the benchtop and the oven cavity are
square and level.
Ensure the electrician provides sufficient
free length of mains cable to reach from the
bottom rear of the cavity to at least 1.5 metres
in front of the bottom edge of the opening.
The cable may enter the cavity from the side,
top or bottom, but top entry must be at the
rear of the cavity.
Use easy to clean finishes for the wall surfaces
surrounding the oven and cooktop to aid
in removal of any cooking fume staining
resulting from the use of the oven and
cooktop.
Check the height from the floor suits the user.
Ensure that drawers and doors will be clear of
obstruction when fully opened.
1
Installation Instructions
Installation instructions
1
Check that the oven cavity is square
and within the limits in the installation
dimensions.
2
Remove the mains wiring access cover.
3
Connect the mains wiring and replace the
access cover.
4
Remove the oven door and accessories, lift
and slide oven into place. When installing
the oven it is essential to centre the product
in the cavity giving a spacing of 2.5mm from
the door edge to the joinery
5
Secure oven in cavity using the four ‘wood
screws’ and washers supplied through the
enamelled frame at either side of the oven as
shown in the flush fitting installation options.
6
Test then refit the door and accessories,
check that the oven is firmly secured in the
kitchen unit.
Installing a cooktop above an oven
If installing a cooktop above the oven ensure
adequate clearance is provided for the
cooktop as per the Cooktop Manufacturers
Instructions.
Flush fitting installation options
a
20 mm
2.5 mm
b
20 mm
2.5 mm
CUPBOARD FRONT
c
20 mm
2.5 mm
DRAWER FRONT
2
Height recommendation guide
Figures are based on an average height of 1650mm (5’5”) wearing shoes. The height of the
product may vary according to the height of the most frequent user.
3
BI602 series Single Built-In Oven BI602ED series Double Built-In Oven
59
595 mm
595 mm
5
m
m
55
0
m
m
550 mm
932 mm
5
m
2
6
915 mm
m
m
578 mm
m
m
0
2
m
m
0
6
4
r
o
o
d
n
e
v
o
m
m
2
6
5
m
m
0
6
4
r
o
o
d
r
e
p
p
u
20 m
m
m
5
1
3
r
o
o
d
r
e
w
o
l
922 mm
585 mm
600 m
m
m
m
0
0
6
16-20 mm
Top View
20 mm
600 mm
570 mm MIN
16-20 mm
Top View
570 mm MIN
20 mm
600 mm
4
BI602CTE series Built-In Oven/Cooktop
Combination
59
5
m
m
55
0
m
m
595 mm
Benchtop Detail
Benchtop
CookTop Cutout*
20 mm
Gap
55 mm
MIN.
578 mm
m
m
0
2
m
m
0
6
4
r
o
o
d
n
e
v
o
m
m
2
6
5
585 mm
m
600 m
*see cooktop installation
instructions p/n 599100
Cooktop Installation
1
Remove the brackets from the cooktop.
2
Place the cooktop in the cutout and secure
using the brackets previously removed.
3
Feed the cooktop wiring harness out
through the oven cavity.
4
Remove the oven connector block cover on
the oven top wiring cover.
5
Connect the cooktop wiring harness lining
the numbers/letters on the harness with
the numbers/letters on the oven connector
block. Leave plastic wiring card attached for
future reference.
6
Clamp the wiring harness with the wiring
clamp on the oven top wiring cover.
7
Replace the oven connector block cover.
OVEN
15 mm
MIN.
16-20 mm
5
Top View
20 mm
600 mm
8
Install the oven as described on page 2.
570 mm MIN
harness detail
plastic
wiring card
oven connector
block
54PNEEN321
54PNEEN321
BI452 series Compact Built-In Oven
595 m
m
550 m
m
BI602XC series Built-In Oven/Microwave
Combination
m
m
5
5
4
mm
0
3
microwave
door
5
6
4
595 m
m
m
560 m
m
m
932 mm
450 mm
m
m
5
1
3
o
o
d
n
e
v
o
Top View
m
0
2
5
r
440 mm
600 m
m
6
m
2
433 mm
m
m
m
m
0
6
4
o
d
n
e
v
o
935 mm
Top View
r
o
595 mm
m
0
2
0
6
930 mm
m
m
2
6
5
70 mm min.
clearance
m
m
0
m
16-20 mm
20 mm
600 mm
570 mm MIN
16-20 mm
20 mm
570 mm MIN
600 mm
6
Loading...