Fire-Lite SLC User Manual

PN 51309:K ECN 08-118

Intelligent Control Panel

S L C

Wiring Manual

Document 51309
2/14/2008 Rev:

K

Fire Alarm System Limitations

While a fire alarm system may lower insurance
rates, it is not a substitute for fire insurance!

An automatic fire alarm system–typically made up of
smoke detectors, heat detectors, manual pull stations,
audible warning devices, and a fire alarm control panel with
remote notification capability–can provide early warning of a
developing fire. Such a system, however, does not assure
protection against property damage or loss of life resulting
from a fire.

The Manufacturer recommends that smoke and/or heat
detectors be located throughout a protected premise follow­ing the recommendations of the current edition of the
National Fire Protection Association Standard 72 (NFPA 72),
manufacturer's recommendations, State and local codes,
and the recommendations contained in the Guides for
Proper Use of System Smoke Detectors, which are made
available at no charge to all installing dealers. These docu­ments can be found at http:/www.systemsensor.com/html/
applicat.html. A study by the Federal Emergency Manage­ment Agency (an agency of the United States government)
indicated that smoke detectors may not go off in as many as
35% of all fires. While fire alarm
systems are designed to provide early warning against fire,
they do not guarantee warning or protection against fire. A
fire alarm system may not provide timely or adequate
warning, or simply may not function, for a variety of reasons:

Smoke detectors may not sense fire where smoke cannot
reach the detectors such as in chimneys, in or behind walls,
on roofs, or on the other side of closed doors. Smoke
detectors also may not sense a fire on another level or floor
of a building. A second-floor detector, for example, may not
sense a first-floor or basement fire.

Particles of combustion or "smoke" from a developing fire
may not reach the sensing chambers of smoke detectors
because:

• Barriers such as closed or partially closed doors, walls, or
chimneys may inhibit particle or smoke flow.

• Smoke particles may become "cold," stratify, and not
reach the ceiling or upper walls where detectors are
located.

• Smoke particles may be blown away from detectors by air
outlets.

• Smoke particles may be drawn into air returns before
reaching the detector.

The amount of "smoke" present may be insufficient to alarm
smoke detectors. Smoke detectors are designed to alarm
at various levels of smoke density. If such density levels are
not created by a developing fire at the location of detectors,
the detectors will not go into alarm.

Smoke detectors, even when working properly, have sens­ing limitations. Detectors that have photoelectronic sensing
chambers tend to detect smoldering fires better than flam­ing fires, which have little visible smoke. Detectors that have
ionizing-type sensing chambers tend to detect fast-flaming
fires better than smoldering fires. Because fires develop in
different ways and are often unpredictable in their growth,
neither type of detector is necessarily best and a given type
of detector may not provide adequate warning of a fire.

Smoke detectors cannot be expected to provide adequate
warning of fires caused by arson, children playing with
matches (especially in bedrooms), smoking in bed, and
violent explosions (caused by escaping gas, improper stor-

age of flammable materials, etc.).
Heat detectors do not sense particles of combustion and

alarm only when heat on their sensors increases at a
predetermined rate or reaches a predetermined level.
Rate-of-rise heat detectors may be subject to reduced
sensitivity over time. For this reason, the rate-of-rise
feature of each detector should be tested at least once
per year by a qualified fire protection specialist. Heat

detectors are designed to protect property, not life.
IMPORTANT! Smoke detectors must be installed in the

same room as the control panel and in rooms used by
the system for the connection of alarm transmission
wiring, communications, signaling, and/or power. If

detectors are not so located, a developing fire may
damage the alarm system, crippling its ability to report
a fire.

Audible warning devices such as bells may not alert
people if these devices are located on the other side of
closed or partly open doors or are located on another
floor of a building. Any warning device may fail to alert
people with a disability or those who have recently con­sumed drugs, alcohol or medication. Please note that:

• Strobes can, under certain circumstances, cause
seizures in people with conditions such as epilepsy.

• Studies have shown that certain people, even when
they hear a fire alarm signal, do not respond or com­prehend the meaning of the signal. It is the property
owner's responsibility to conduct fire drills and other
training exercise to make people aware of fire alarm
signals and instruct them on the proper reaction to
alarm signals.

• In rare instances, the sounding of a warning device
can cause temporary or permanent hearing loss.

A fire alarm system will not operate without any
electrical power. If AC power fails, the system will
operate from standby batteries only for a specified time
and only if the batteries have been properly maintained
and replaced regularly.

Equipment used in the system may not be technically
compatible with the control. It is essential to use only
equipment listed for service with your control panel.

Telephone lines needed to transmit alarm signals from
a premise to a central monitoring station may be out of
service or temporarily disabled. For added protection
against telephone line failure, backup radio transmis­sion systems are recommended.

The most common cause of fire alarm malfunction is
inadequate maintenance. To keep the entire fire alarm
system in excellent working order, ongoing maintenance
is required per the manufacturer's recommendations,
and UL and NFPA standards. At a minimum, the require­ments of NFPA 72 shall be followed. Environments with
large amounts of dust, dirt or high air velocity require
more frequent maintenance. A maintenance agreement
should be arranged through the local manufacturer's
representative. Maintenance should be scheduled
monthly or as required by National and/or local fire codes
and should be performed by authorized professional fire
alarm installers only. Adequate written records of all
inspections should be kept.

PrecauLarge.PMD 02/26/2007

Installation Precautions

Adherence to the following will aid in problem-free
installation with long-term reliability:

WARNING - Several different sources of power can be
connected to the fire alarm control panel. Disconnect all

sources of power before servicing. Control unit and asso­ciated equipment may be damaged by removing and/or
inserting cards, modules, or interconnecting cables while
the unit is energized. Do not attempt to install, service, or
operate this unit until this manual is read and understood.

CAUTION - System Reacceptance Test after Software
Changes. To ensure proper system operation, this product

must be tested in accordance with NFPA 72 after any
programming operation or change in site-specific software.
Reacceptance testing is required after any change,
addition or deletion of system components, or after any
modification, repair or adjustment to system hardware or
wiring.

All components, circuits, system operations, or software
functions known to be affected by a change must be 100%
tested. In addition, to ensure that other operations are not
inadvertently affected, at least 10% of initiating devices that
are not directly affected by the change, up to a maximum of
50 devices, must also be tested and proper system
operation verified.

This system meets NFPA requirements for indoor dry
operation at 0-49° C/32-120° F
93 ±2% RH (non-condensing) at 32 ±2° C/90 ±3° F.
However, the useful life of the system's standby batteries
and the electronic components may be adversely affected
by extreme temperature ranges and humidity. Therefore, it
is recommended that this system and all peripherals be
installed in an environment with a nominal room tempera­ture of 15-27° C/60-80° F.

Verify that wire sizes are adequate for all initiating and
indicating device loops. Refer to manual Specifications
section for maximum allowable I.R. drop from the specified
device voltage.

and at a relative humidity of

Like all solid state electronic devices, this system may
operate erratically or can be damaged when subjected to
lightning-induced transients. Although no system is
completely immune from lightning transients and
interferences, proper grounding will reduce susceptibility.

Overhead or outside aerial wiring is not recommended, due
to an increased susceptibility to nearby lightning strikes.

Consult with the Technical Services Department if any
problems are anticipated or encountered.

Disconnect AC power and batteries prior to removing or
inserting circuit boards. Failure to do so can damage
circuits.

Remove all electronic assemblies prior to any drilling,
filing, reaming, or punching of the enclosure. When
possible, make all cable entries from the sides or rear.
Before making modifications, verify that they will not
interfere with battery, transformer, and printed circuit board
location.

Do not tighten screw terminals more than 9 in-lbs.
Over-tightening may damage threads, resulting in reduced
terminal contact pressure and difficulty with screw terminal
removal.

This system contains static-sensitive components.

Always ground yourself with a proper wrist strap before
handling any circuits so that static charges are removed
from the body. Use static-suppressive packaging to
protect electronic assemblies removed from the unit.

Follow the instructions in the installation, operating, and
programming manuals. These instructions must be
followed to avoid damage to the control panel and
associated equipment. FACP operation and reliability
depend upon proper installation by authorized personnel.

FCC Warning

WARNING: This equipment generates, uses, and can

radiate radio frequency energy and if not installed and
used in accordance with the instruction manual, may
cause interference to radio communications. It has
been tested and found to comply with the limits for class
A computing device pursuant to Subpart B of Part 15 of
FCC Rules, which is designed to provide reasonable
protection against such interference when operated in a
commercial environment. Operation of this equipment
in a residential area is likely to cause interference, in
which case the user will be required to correct the
interference at their own expense.

PrecauLarge.PMD 02/26/2007

Canadian Requirements

This digital apparatus does not exceed the Class A
limits for radiation noise emissions from digital
apparatus set out in the Radio Interference Regulations
of the Canadian Department of Communications.

Le present appareil numerique n'emet pas de bruits
radioelectriques depassant les limites applicables aux
appareils numeriques de la classe A prescrites dans le
Reglement sur le brouillage radioelectrique edicte par
le ministere des Communications du Canada.

This Page Intentionally Left Blank

4 The SLC Wiring Manual PN 51309:K 2/14/08

Introduction 8

Scope ............................................................................................................................8

Reference Documentation ..................................................................................... 9

Overview ................................................................................................................... 10

Polling Protocols ............................................................................ ..........................10

Available Protocols ......................................................................................... .... 10

Devices ....................................................................................................................... 10

Isolator Module ................................................................................................... 10

Monitor Modules .................................................................................................10

Control Modules ................................................................................................. 11

Relay Modules .................................................................................................... 11

Intelligent Detectors ............................................................................. ............... 11

Manual Pull Station .................................................................................... ......... 12

300 Series Addressable Devices ................................................................ ......... 12

SLC Performance ........................................................................... ..........................12

Surge Suppression .................................................................................................... 12

Wiring Requirements 13

Wire Sizing ............................................................... .................................. ............... 13

CLIP (Classic Loop Interface Protocol) Mode ................................................... 13

LiteSpeed Mode .................................................................................................. 13

Measuring Resistance & Length ............................................................................. 14

Two-Wire SLC - Style 4 (Class B) .....................................................................14

Loop Resistance ............................................................................... ............ 14

Total Wire Length ........................................................................................14

Four-Wire SLC Style 6 & 7 (Class A) ................................................................ 15

Loop Resistance ............................................................................... ............ 15

Total Wire Length ........................................................................................15

Shield Wire Termination ......................................................................................... 16

Control Panel Terminal Blocks ...............................................................................17

MS-9200 .............................................................................................................. 17

MS-9600, MS-9600LS, MS-9600LSC & MS-9600UDLS ................................. 17

MS-9200UD & MS-9200UDLS .................................................. ....................... 18

MS-9050UD ........................................................................................................ 18

Non-Isolated Circuits 19

Overview ................................................................................................................... 19

NFPA Style 4 SLC .................................................................................................... 19

NFPA Style 6 SLC .................................................................................................... 20

SLC Circuits with Isolators 21

Fault Isolator Module - I300 ...................................................................................21

Isolating an SLC Branch ..................................................................................... 21

Wiring an Isolator Module ..................................................................................21

NFPA Style 4 SLC Using an I300 Module .............................................................22

NFPA Style 6 SLC Using an I300 Module .............................................................23

NFPA Style 7 SLC Using an I300 Module .............................................................24

Monitor Modules 25

Descriptions ............................................................................................................... 25

MMF-300 Monitor Module ................................................................................25

MMF-302 Monitor Module ................................................................................25

MDF-300 Dual Monitor Module ........................................................................26

MMF-301 Monitor Module ................................................................................26

MMF-300-10 ....................................................................................................... 27

The SLC Wiring Manual PN 51309:K 2/14/08 5

MMF-302-6 .........................................................................................................28

Installation .................................................................................................................29

Setting an SLC address for a Single Point Module .............................................29

Setting an SLC address for a Multi-Point Module ..............................................30

MMF-300 Wiring Diagrams ....................................................................................31

Wiring a NFPA Style B IDC with an MMF-300 ...............................................31

Wiring a NFPA Style D IDC with an MMF-300 ............................................... 32

MMF-300-10 Wiring Diagrams ............................................................................... 33

Wiring a NFPA Style B IDC with an MMF-300-10 .......................................... 33

Wiring a NFPA Style D IDC with an MMF-300-10 ..........................................34

MDF-300 Wiring Diagrams ..................................................................................... 35

Wiring a NFPA Style B IDC with an MDF-300 ................................................35

MMF-302 Wiring Diagrams ....................................................................................36

Wiring a NFPA Style B IDC with an MMF-302 ................................................36

Wiring a NFPA Style D IDC with an MMF-302 ................................................ 37

MMF-302-6 Wiring Diagrams .................................................................................38

Wiring a NFPA Style B IDC with an MMF-302-6 .............................................38

Wiring a NFPA Style D IDC with an MMF-302-6 .............................................39

Control Modules 40

Description ................................................................................................................ 40

CMF-300 Installation ...............................................................................................40

Setting an SLC address for an CMF-300 Module ............................................... 40

Wiring a Notification Appliance Circuit (NAC) with an CMF-300 ................... 40

Wiring a CMF-300 Module .....................................................................................41

Wiring a Style Y NAC (Two-Wire) ...................................................................41

Wiring a Style Z NAC (Four-Wire) ....................................................................42

CMF-300-6 Installation ............................................................................................ 43

Cabinet Installation .............................................................................................43

Setting an SLC address for an CMF-300-6 Module ........................................... 43

Setting NACs as Style Y or Style Z ....................................................................43

Disabling Unused Module Addresses .................................................................43

Short Circuit Protection ..................................................................................... ..43

Features Not Supported .......................................................................................44

Circuit Board Information .................................................................................44

Wiring a CMF-300-6 Module ..................................................................................45

Wiring a Style Y NAC (Two-Wire) ...................................................................45

Wiring a Style Z NAC (Four-Wire) ....................................................................46

Relay Modules 47

Description ................................................................................................................ 47

CRF-300 Installation & Wiring ..............................................................................47

Setting an SLC address for a CRF-300 Module ..................................................47

Wiring a CRF-300 Module (Form-C Relay) ....................................................... 47

CRF-300-6 Circuit Board Information .................................................................48

CRF-300-6 Installation & Wiring ........................................................................... 49

Cabinet Installation .............................................................................................49

Setting an SLC address for a CRF-300-6 Module .............................................. 49

Disabling Unused Module Addresses ................................................................49

Wiring a CRF-300-6 Module (Form-C Relay) ...................................................49

Intelligent Detector Bases 50

Description ................................................................................................................ 50

Installation and Wiring ............................................................................................50

Setting the Detector Address ...............................................................................50

6 The SLC Wiring Manual PN 51309:K 2/14/08

Wiring a Detector Base ....................................................................................... 50

Addressable Beam Detectors 51

Description ................................................................................................................ 51

Installation and Wiring ............................................................................................ 51

Setting an SLC Address for a Beam Detector .....................................................51

Wiring a Beam Detector ..................................................................................... 51

Addressable Manual Pull Station 52

Description ................................................................................................................ 52

Installation ................................................................................................................ 52

Setting an SLC address .......................................................................................52

Wiring a Manual Pull Station .............................................................................. 52

Appendix A: Power Considerations 53

Supplying Power to 24 VDC Detectors .................................................................. 53

Resistance and Size ............................................................................................. 53

Supervising 24 VDC Power ..................................................................................... 54

Appendix B: Surge Suppression 55

Introduction .............................................................................................................. 55

Installation ................................................................................................................ 55

Wiring Diagram for MS-9200 ............................................................................. 56

DTK-2LVLP-F Connections ...................................................................... 56

PLP-42N Connections ................................................................................ 56

SLCP-030 Connections ............................................................................... 56

Wiring Diagram for MS-9600, MS-9600LS, MS-9600LSC, MS-9600UDLS,

MS-9200UD, MS-9200UDLS and MS-9050UD ................................................ 57

DTK-2LVLP-F Connections ...................................................................... 57

PLP-42N Connections ................................................................................ 57

SLCP-030 Connections ............................................................................... 57

Appendix C: Terminal Conversion Charts for New & Legacy Devices 58

CRF-300 .................................................................................................................... 58

CMF-300 and MMF-302 .......................................................................................... 59

MMF-300 ................................................................................................................... 60

The SLC Wiring Manual PN 51309:K 2/14/08 7

Introduction Scope

Introduction

Scope

This document describes the operation, installation and wiring of various Signaling Line Circuit (SLC )
devices when used with the Fire•Lite MS-9200/MS-9200E, the Fire•Lite MS-9600/MS-9600E, the Fire­Lite MS-9600LS, the Fire-Lite MS-9600LSC, the Fire-Lite MS-9600LSE, the Fire-Lite MS-9600UDLS/
MS-9600UDLSE, the Fire•Lite MS-9200UD/MS-9200UDE, the Fire•Lite MS-9200UDLS/MS­9200UDLSE and the Fire-Lite MS-9050UD control panels. It also provides basic information that applies
to Fire•Lite SLC loops in general, such as the branch resistance measurements.

Note: Any reference in this manual to the MS-9200, MS-9200UD, MS-9200UDLS, MS-9600, MS-9600LS or MS­9600UDLS includes the MS-9200E, MS-9200UDE, MS-9200UDLSE, MS-9600E, MS-9600LSE or MS-9600UDLSE
respectively.

Additional information about the specific control panel and the modules and detectors referenced in this
document can be found in the respective installation manual as listed in Table 1, “Reference
Documentation,” on page 9.

Currently, there are two styles of Modules available, legacy version and newer version. The obvious
difference between the two styles is the orientation of the rotary dials. Refer to the diagram below for an
example of each.

CMF-300

Legacy Version Module

(Vertical Rotary Dial)

Note: Only MMF-300, MMF-302, CRF-300 and CMF-300 modules are available as newer type modules. Both

the legacy and newer versions share the same part numbers. The newer version modules will be phased in,
replacing the legacy version. This manual contains information and wiring diagrams for the newer version of the
modules. Refer to "Appendix C: Terminal Conversion Charts for New & Legacy Devices" on page 58 for
additional information.

Newer Version Module

(Horizontal Rotary Dial)

8

CMF-300

The SLC Wiring Manual PN 51309:K 2/14/08

Scope Introduction

Reference Documentation

The table below accommodates a list of document sources containing additional information regarding the
devices used on a Signaling Line Circuit:

For information on... Refer to... Part Number

MS-9200/MS-9200E Instruction Manual 51003
MS-9600/MS-9600E Instruction Manual 51335
MS-9200UD/MS-9200UDE Instruction Manual 51906
MS-9200UDLS/MS-9200UDLSE Instruction Manual 52750
MS-9600LS/MS-9600LS(C/E) & MS-9600UDLS/MS9600UDLSE Instruction Mnual 52646
MS-9050UD Instruction Manual 52413
Compatible Devices Device Compatibility Document 15384
BG-12LX Pull Station Installation Instructions 51094
MMF-300 Monitor Module Installation Instructions F300-02-00
MMF-300-10 Monitor Module Installation Instructions F300-20-00
MMF-301 Mini Monitor Module Installation Instructions F300-05-00
MMF-302 Monitor Module Installation Instructions F300-03-00
MMF-302-6 Interface Module Installation Instructions F300-22-00
MDF-300 Dual Monitor Module Installation Instructions F300-09-00
CMF-300 Control Module Installation Instructions F300-07-00
CMF-300-6 Control Module Installation Instructions F300-21-00
CRF-300 Relay Module Installation Instructions F300-04-00
CRF-300-6 Relay Module Installation Instructions F300-19-00
I300 Isolator Module Installation Instructions F300-06-00
AD350 Multicriteria Detector Installation Instructions F300-17-00
AD355 Multicriteria Detector Installation Instructions F300-24-00
SD350 & SD350T Photo Detector Installation Instru ctions F300-14-00
SD355 & SD355T Photo Detector Installation Instru ctions F300-24-00
CP350 Ionization Detector Installation Instructions F300-15-00
CP355 Ionization Detector Installation Instructions F300-23-00
H350 Heat Detector Installation Instructions F300-12-00
H350R Heat Detector w/ROR Installation Instructions F300-13-00
H355 Heat Detector (135
H355R Heat Detector w/ROR Installation Instructions F300-25-00
H355HT Heat Detector (190
D350P Duct Detector Installation Instructions F300-10-00
D350PL(A) Duct Detector - low flow Installation Instructions F300-27-00
D350RP Duct Detector w/Relay Installation Instructions F300-11-00
D350RPL(A) Duct Detector w/Relay - low flow Installation Instructions F300-28-00
BEAM355(S) Addressable Beam Detector Installation Instructions F300-29-00
B350LP Plug-in Detector Base Installation Instructions F400-21-00
B501BH Sounder Detector Base Installation Instructions D650-03-00
B224RB Relay Detector Base Installation Instructions D450-16-01
B224BI Isolator Detector Base Installation Instructions D450-15-00

°)

°)

Table 1 Reference Documentation

Installation Instructions F300-25-00

Installation Inatructions F300-25-00

The SLC Wiring Manual PN 51309:K 2/14/08 9

Introduction Overview

Overview

Communication between the control panel and intelligent addressable monitor and control devices takes
place through a Signaling Line Circuit (SLC), which can be wired to meet the requirements of NFP A Style
4, Style 6, or Style 7.

At least one secondary surge protector must be used with each SLC wiring pair whenever SLC wiring
runs outside the building. For detailed information refer to "Appendix B: Surge Suppression" on page

55.

Polling Protocols

The MS-9200UDLS/E, MS-9600LS(C/E) and MS-9600UDLS/E support LiteSpeed protocol or Classic
Loop Interface Protocol (CLIP). The MS-9200/E, MS-9600/E, MS-9200UD/E and MS-9050UD
support Classic Loop Interface Protocol (CLIP) only.

Available Protocols

LiteSpeed is a communication protocol that greatly enhances the speed of communication between analog
intelligent devices. Only the MS-9200UDLS/E, MS-9600LS(C/E) and MS-9600UDLS/E are capable of
operating in LiteSpeed mode.

CLIP (Classic Loop Interface Protocol) polls devices in sequential order. All Fire-Lite addressable fire
alarm control panels can operate in CLIP mode. This is the default mode of operation for the FACPs.

Devices

Protocol Use

Use one of the following options with LiteSpeed/CLIP mode:

1. Program all modules and detectors on an FACP as LiteSpeed.

2. Program all modules and detectors on an FACP as CLIP.

Note: FACPs with more than one SLC loop must be programmed for only LiteSpeed or CLIP mode of operation.
Communication protocols cannot be split between SLC loops.

Isolator Module

The I300 Isolator Module permits a zone of detectors and modules to be fault isolated from the remainder
of the SLC loop, allowing critical components to function in the event of a circuit fault. Isolator modules
are required to meet the requirements of an NFPA Style 7 circuit.

Monitor Modules

Addressable modules that allow the control panel to monitor entire circuits of conventional alarm initiating
devices, such as manual pull stations, smoke detectors, heat detectors, waterflow and supervisory devices.

MMF-300 - Monitors a Style B (Class B) or Style D (Class A) circuit of dry-contact input devises.
MMF-300-10 - Monitors ten (10) Style B (Class B) or five (5) Style D (Class A) normally open contact

device circuits.

10

MMF-301 - Same as the MMF-300 except offered in a smaller package for mounting with Style B wired
devices. This module does not have an LED.

MMF-302 - Monitors a single IDC of two-wire smoke detectors.
MMF-302-6 - An addressable module that provides an interface between the control panel and six (6) Style

B (Class B) or three (3) Style D (Class A) IDCs of two-wire smoke detectors.
MDF-300 - Similar to MMF-300, but provides for two independent Style B IDCs.

The SLC Wiring Manual PN 51309:K 2/14/08

Control Modules

Through the CMF-300 addressable control module, the control panel can selectively activate a Notification
Appliance Circuit (NAC).

CMF-300-6 - Similar in operation to the CMF-300, except it can activate six (6) Style Y (Class B) or three
(3) Style Z (Class A) NACs.

Relay Modules

The CRF-300 addressable relay module provides the control panel with a dry-contact output for activating
a variety of auxiliary devices.

CRF-300-6 - Similar in operation to the CRF-300, except it provides six (6) Form-C relays.

Intelligent Detectors

AD350 - A multicriteria smoke sensor that combines a photoelectric sensing chamber and 135°F (57.2°C)
fixed temperature heat detection. The sensor uses addressable communication to transmit smoke density
and other information to the control panel. It adjusts its detection parameters and alarm threshold depending
on the ambient conditions it samples in its environment.

AD355 - A multicriteria smoke sensor that combines a photoelectric sensing chamber and 135°F (57.2°C)
fixed temperature heat detection. The sensor uses addressable communication to transmit smoke density
and other information to the control panel. It adjusts its detection parameters and alarm threshold
depending on the ambient conditions it samples in its enviornment.

CP350 - An addressable ionization smoke detector which measures the level of combustion products in
its chamber using the ‘ionization principle.’

CP355 - An addressable ionization smoke detector which measures the level of combustion products in
its chamber using the ‘ionization principle.’

D350P - An addressable photoelectric duct detector. The D350RP includes an alarm relay. Air velocity
rating is 500 to 4,000 feet per minute.

D350PL -An addressable low flow photoelectric duct detector (D350PLA for Canada). The D350RPL
includes an alarm relay (D350RPLA for Canada). Low Flow refers to the air velocity rating of 100 to 4,000
feet per minute (0.5 to 20.32 m/sec.)

1

H350

- An addressable detector using a thermistor sensing circuit for fast response. H350R incorporates

a thermal rate of rise of 15°F (9.4°C)/minute.

1

- An addressable 135° fixed temperature heat detector using a thermistor sensing circuit for fast

H355
response. H355R incorporates a thermal rate of rise of 15° F (9.4° C)/minute.

H355HT

1

- An addressable 190° fixed temperature heat detector using a thermistor sensing circuit for fast

response.
SD350 - An addressable photoelectric smoke detector which provides smoke sensing utilizing optical sense

technology. The SD350T includes a 135° F fixed thermal sensor.
SD355 - An addressable photoelectric smoke detector which provices smoke sensing utilizing optical sense

technology. The SD355T includes a 135° F fixed thermal sensor.
BEAM355 - An addressable long range projected beam smoke detector designed to provide open area

protection. The BEAM355S has an integral sensitivity test feature that consists of a test filter attached
to a servomotor inside the detector optics.

1

Addressable Heat Detectors are not compatible with the MS-9200(E).

The SLC Wiring Manual PN 51309:K 2/14/08 11

Introduction SLC Performance

Manual Pull Station

The BG-12LX is a dual-action pull station that, when activated, provides an addressable identification and
its location to the control panel. An addressable monitor module is mounted inside the pull station to
facilitate servicing and replacement.

300 Series Addressable Devices

Fire•Lite’s 300 series of addressable devices are fully compatible with the MS-9200, MS-9200UD,
MS-9200UDLS, MS-9600, MS-9600LS(C/E), MS-9600UDLS/E and MS-9050UD FACPs. The devices
must be configured for CLIP (Classic Loop Interface Protocol) Mode operation. The address of 300 series
devices cannot be set above 99. Compatible devices include:

• SD300 Photo • M300 Monitor Module

• SD300T Photo w/Thermal • M301 Mini Monitor Module

• CP300 Ionization • M302 2-wire Monitor Module

• BG-10LX Pull Station • C304 Control/Relay Module

SLC Performance

SLC performance depends on the type of circuit (Style 4, Style 6, or Style 7) and the components on the
circuit.

Note: SLC operation meeting Style 7 requirements isolates each device on the SLC from faults that may occur within
other areas of the SLC.

Wiring style requirements are determined by national and local codes. Consult with the Authority Having
Jurisdiction before wiring the SLC. The table below (derived from NFPA 72-1999) lists the trouble
conditions that result when a fault exists on an SLC.

Ty pe of Fault Style 4 Style 6 Style 7

Single Open Trouble Alarm, Trouble Alarm, Trouble
Single Ground Alarm, Trouble

Short Trouble Trouble Alarm, Trouble
Short and open Trouble Trouble Trouble
Short and ground Trouble Trouble Alarm, Trouble
Open and ground Trouble Alarm, Trouble Alarm, Trouble
Communications

loss

• Trouble - The control panel will indicate a trouble condition for this type of fault.

• Alarm - The control panel must be able to process an alarm input signal in the presence of
this type of fault.

Surge Suppression

Alarm, Trouble

(ground)

Trouble Trouble Trouble

(ground)

Alarm, Trouble
(ground)

Table 2 SLC Performance

12

One primary surge protector must be used with each SLC wiring pair whenever SLC wiring runs outside
the building. For detailed information refer to "Appendix B: Surge Suppression" on page 55.

The SLC Wiring Manual PN 51309:K 2/14/08

Wire Sizing Wiring Requirements

Wiring Requirements

Wire Sizing

The SLC requires use of a specific wire type, depending on the mode of operation, to ensure proper circuit
functioning. Wire size should be no smaller than 18 AWG (0.75 mm

2

mm

) wire. The wire size depends on the length of the SLC circuit. It is recommended that all SLC wiring

2

) and no larger than 12 AWG (3.25

be twisted-pair to minimize the ef fects of electrical interference.

CLIP (Classic Loop Interface Protocol) Mode

All addressable F ACPs can operated in CLIP (Classic Loop Interface Protocol) mode. It is recommended
that all SLC wiring be twisted-pair and shielded when operating in CLIP mode to reduce the effects of
electrical interference. Use the table below to determine the specific wiring requirements for the SLC.

Wire Requirements Distance in Feet (meters) Wire Size Wire Type

2

Belden 9583, Genesis 4410,

)

Signal 98230, WPW D999

2

Belden 9581, Genesis 4408,

)

Signal 98430, WPW D995

2

Belden 9575, Genesis 4406,

)

& 4606, Signal 98630, WPW
D991

2

Belden 9574, Genesis 4402 &

)

4602, Signal 98300, WPW
D975

Twisted-pair, shielded

Untwisted, unshielded
wire, inside conduit or
not in conduit

10,000 feet (3,048 m)

8,000 feet (2,438 m)

4,875 feet (1,486 m)

3,225 feet (983 m)

MS-9200 = 1,000 feet (305 m)
MS-9600, MS-9600LS(C) &

MS-9600UDLS = 3,000 feet (914 m)
MS-9200UD & MS-9200UDLS =

3,000 feet (914 m)
MS-9050UD = 3,000 feet (914 m)

12 AWG (3.1 mm

14 AWG (2.0 mm

16 AWG (1.3 mm

18 AWG (0.75 mm

12 to 18 A W G

Table 3 SLC Wiring Requirements in CLIP Mode

LiteSpeed Mode

The MS-9200UDLS, MS-9600LS(C) and MS-9600UDLS SLC can be programmed to operate in
LiteSpeed mode for a quicker device response time. While shielded wire is not required, it is recommended
that all SLC wiring be twisted-pair to minimize the effects of electrical interference. Use the following
table to determine the specific wiring requirements for the SLC.

Wire Requirements Distance in Feet (meters) Wire Size Wire Type

2

Belden 5020UL & 6020UL,

)

Genesis WG-4315 & WG-4515

2

Belden 5120UL & 6120UL,

)

Genesis WG-4313 & WG-4513
Belden 5220UL & 6220UL,

Genesis WG-4311 & WG-4511

2

Belden 5320UL & 6320UL,

)

Genesis WG-4306 & WG-4506

Twisted-pair,
unshielded

10,000 feet (3,048 m)

8,000 feet (2,438 m)

4,875 feet (1,486 m)

3,225 feet (983 m)

12 AWG (3.1 mm

14 AWG (2.0 mm

16 AWG (1.3 mm2)

18 AWG (0.75 mm

Table 4 SLC Wiring Requirements in LiteSpeed Mode

The SLC Wiring Manual PN 51309:K 2/14/08 13

Wiring Requirements Measuring Resistance & Length

Measuring Resistance & Length

Two-Wire SLC - Style 4 (Class B)

Loop Resistance

T -tapping of the SLC wiring is permitted for 2-wire Style 4 configurations. The total DC resistance from
the control panel to each branch end cannot exceed 40 ohms. Measure DC resistance as detailed and shown
below:

1. With power removed, short the termination point of one branch at a time and measure the DC
resistance from the beginning of the SLC to the end of that particular branch.

2. Repeat this procedure for all remaining branches in the SLC.

Short Point

SLC Out

Branch

SLC-meas1.cdr

Figure 1 Measuring DC Resistance of a Two-Wire SLC

Total Wire Length

The total wire length of all combined branches of one SLC cannot exceed the limits set forth in each
system’s instruction manual. Determine the total length in each SLC by summing the wire lengths of all
branches of one SLC.

In the following figure, the total length of the SLC is determined by adding the lengths of Branch A plus
Branch B plus Branch C.

Branch A Branch B

SLC T erminal
Block

Branch C

SLC-meas2.cdr

Figure 2 Measuring the Total Wire Length - Two-Wire SLC

14

The SLC Wiring Manual PN 51309:K 2/14/08

Measuring Resistance & Length Wiring Requirements

Four-Wire SLC Style 6 & 7 (Class A)

Loop Resistance

The total DC resistance of the SLC pair cannot exceed 40 ohms. Measure DC resistance as detailed and
shown below.

1. Disconnect the SLC channel B (Out) and SLC channel A (Return) at the control panel.

2. Short the two leads of SLC channel A (Return).

3. Measure the resistance across the SLC channel B (Out) leads.

SLC Out

Short Point

SLC Return

SLC-meas3.cdr

Figure 3 Measuring DC Resistance of a Four-Wire SLC

Total Wire Length

The total wire length in a four-wire SLC cannot exceed the limits set forth in each system’s instruction
manual. The figure below identifies the output and return loops from SLC terminal on the control panel:

SLC channel B
(output loop)

SLC T erminal
Block

B+ B– A– A+

SLC channel A
(return loop)

SLC-meas4.cdr

Figure 4 Measuring the Wire Length – Four-Wire SLC

The SLC Wiring Manual PN 51309:K 2/14/08 15

Wiring Requirements Shield Wire Termination

Shield Wire Termination

The drawing below shows the method of proper termination of the shield.
Connect the metal conduit to the cabinet by using the proper connector. Feed the shielded wire through

the conduit, into the control box. The shield drain wire must be connected to the “shield” terminal on the
SLC terminal block.

Note: Use of good wiring practice consistent with local electrical codes is expected.

CAUTION: Do not let the shield drain wire or the shield foil touch the system cabinet or be connected
to earth ground at any point.

MS-9600
MS-9600LS
MS-9600LSC
MS-9600UDLS
MS-9200UD
MS-9200UDLS
MS-9050UD

Shield Drain Wire

Cabinet

Shield Foil

MS-9200

Conduit

SLC-shieldterm.cdr

Figure 5 Shield Termination

16

The SLC Wiring Manual PN 51309:K 2/14/08

Control Panel Terminal Blocks

The terminal blocks on the control panel circuit board that concern the SLC circuit are described below.
For more information on this subject refer to the control panel’s Instruction Manual.

MS-9200

TB4 provides three types of 24 VDC power; Unregulated, Nonresettable and Resettable.
TB6 provides connections for the SLC wiring.

Unregulated Power

Nonresettable Power

TB4

Resettable Power

Connections for wire shield

SHIELD SLC SLC

TB6

SLC Out

Figure 6 MS-9200 Terminal Blocks

SLC-9200tb.cdr

SLC
Return

MS-9600, MS-9600LS, MS-9600LSC & MS-9600UDLS

TB3 provides two types of 24 VDC power; Nonresettable and Resettable.
TB8 provides connections for the SLC wiring.

Resettable Power

TB3

Nonresettable
Power

TB8

SLC Out

Figure 7 MS-9600 Series Terminal Blocks

Connections for
wire shield

SHIELDSLC SLC SLC SLC

SLC-9600tb.cdr

SLC Return

The SLC Wiring Manual PN 51309:K 2/14/08 17

Wiring Requirements Control Panel Terminal Blocks

MS-9200UD & MS-9200UDLS

TB1 provides two types of 24 VDC power; Nonresettable and Resettable.
TB10 provides connections for the SLC wiring.

Nonresettable Power

Resettable
Power

Connections for
wire shield

SLC

TB1

SLC Out

TB10

SLC Return

SLC Out

Figure 8 MS-9200UD & MS-9200UDLS Terminal Blocks

MS-9050UD

24 VDC power may be supplied by a remote power supply such as the Fire-Lite FCPS-24FS6/8.
TB2 provides connections for the SLC wiring.

Connections for wire shield

SLC-9200udtb.cdr

18

SLC-9050udtb.cdr

SLC Return

SLC Out

Figure 9 MS-9050UD Terminal Block

The SLC Wiring Manual PN 51309:K 2/14/08

Overview

This chapter concerns itself with the two styles of circuits that do not require isolation devices:

• NFPA Style 4

• NFPA Style 6

NFPA Style 4 SLC

NFPA Style 4 requirements can be met by using the diagram below.

• T-tapping of the SLC wiring is allowed for Style 4 configuration.

Non-Isolated Circuits

Two-wire Addressable Detector

Addressable Module

B+ B–

T-tapped Circuits

Control Panel
SLC

SLC-style4.cdr

Figure 10 Basic NFPA Style 4 SLC

The SLC Wiring Manual PN 51309:K 2/14/08 19

Non-Isolated Circuits NFPA Style 6 SLC

NFPA Style 6 SLC

NFPA Style 6 requirements can be met by using the diagram below.

• T-tapping of the SLC wiring is NOT allowed for Style 6 configuration.

Two-wire Addressable Detector

SLC Out

Addressable Module

B+ B– A– A+

SLC Return

Control Panel
SLC

SLC-style6.cdr

Figure 11 Basic NFPA Style 6 SLC

20

The SLC Wiring Manual PN 51309:K 2/14/08

Fault Isolator Module - I300 SLC Circuits with Isolators

SLC Circuits with Isolators

Fault Isolator Module - I300

The I300 is used to protect critical elements of the SLC from faults on other SLC branches or segments
A Fault Isolator Module on both sides of a device is required to comply with NFPA Style 7 requirements.
A maximum of 25 addressable devices can be connected between isolator Modules.
When more than 100 Isolator Modules are connected to an SLC loop, the address capacity of the loop is

reduced by two (2) addresses for every isolator device in excess of 100.

Isolating an SLC Branch

The module continuously monitors the circuit connected to terminals 3(–) and 4(+). Upon power-up, an
integral relay is latched on. The module periodically pulses the coil of this relay. A short circuit on the SLC
resets the relay. The module detects the short and disconnects the faulted SLC branch or segment by
opening the positive side of the SLC (terminal 4). This isolates the faulty branch from the remainder of
the loop preventing a communication problem with all other addressable devices on the remaining branches
(labeled “Continuation of the SLC” in the figure below). During a fault condition, the control panel registers
a trouble condition for each addressable device which is isolated on the SLC segment or branch. Once the
fault is removed, the module automatically reapplies power to the SLC branch or segment.

Wiring an Isolator Module

The figure below shows typical wiring of an Isolator Module:

Continuation
of the SLC

IN
IN

OUT

OUT

SLC

Figure 12 Wiring an I300 Module

SLC-isowire.cdr

Isolated branch
of the SLC

The SLC Wiring Manual PN 51309:K 2/14/08 21

SLC Circuits with Isolators NFPA Style 4 SLC Using an I300 Module

NFPA Style 4 SLC Using an I300 Module

A variation of a Style 4 operation using isolator modules to protect each branch of the SLC. Refer to Figure
12 on page 21 for I300 wiring.

B– B+

1
2

I300

3
4

1
2

I300

3
4

1
2

I300

3
4

Control Panel
SLC

Two-wire Addressable
Detector

Isolated Branch

Isolated Branch

Addressable Pull Station

Isolated Branch

Figure 13 NFPA Style 4 SLC using I300 modules

SLC-style4i300.cdr

22

The SLC Wiring Manual PN 51309:K 2/14/08

NFPA Style 6 SLC Using an I300 Module

A variation of Style 6 operation using isolator modules to protect a section of the SLC. By flanking each
group of devices with an I300 fault isolator module each group is protected from faults that may occur in
the other groups. For example, a fault in Section B will not effect Sections A & C. The isolator modules
on either side of Section B will open the loop. Section A will still operate from power on the SLC Out side
and Section C will operate from the SLC Return side.

• A combination of isolator modules and isolat or bases may be used.

• T-tapping is NOT allowed within the Style 6 configuration.

• I300 modules shall be within 20 feet (6.1 meters) of device and use metal conduit.

123

I300

4

Two-wire
Addressable
Detector

Section A

SLC Out

Section B

Section C

Addressable

Pull Station

SLC Return

1

2

3

I300

4

3 4

I300

1 2

B– B+ A+ A–

Control Panel

2 1

I300

4 3

Cabinet or
Enclosure

SLC-style6i300.cdr

Figure 14 NFPA Style 6 SLC using I300 modules

The SLC Wiring Manual PN 51309:K 2/14/08 23

SLC Circuits with Isolators NFPA Style 7 SLC Using an I300 Module

NFPA Style 7 SLC Using an I300 Module

Style 7 operation requires using isolator modules before and after each device. Flanking each device with
an isolator provides fault protection to all other devices on the loop.

• T-tapping is NOT allowed within the Style 7 wiring configuration.

• When a detector base or pull station is used, install I300 modules on both sides of the device.

• Connections between isolator modules and the device they isolate must be “close nippled” conduit,

within 3 feet (91.44 cm).

1

2

3

I300

4

1

2

3

I300

4

3 4

I300

1 2

3 4

I300

1 2

Two-Wire
Addressable
Detector

SLC Out

3 4

I300

1 2

Two-wire
Addressable
Detector

2 1

4 3

2 1

I300

4 3

Addressable

Pull Station

4 3

I300

2 1

SLC Return

I300

24

B– B+ A+ A–

Control Panel

SLC-style7i300.cdr

Figure 15 NFPA Style 7 SLC

The SLC Wiring Manual PN 51309:K 2/14/08

Descriptions Monitor Modules

Monitor Modules

Descriptions

These addressable modules monitor conventional contact-type alarm initiating devices. You can configure
module circuits as an NFP A Style B (Class B) or Style D (Class A) Initiating Device Circuits (IDC). There
is no limit to the number of contact-type devices installed on a monitor module circuit.

Note: For more information on the individual module specifications refer to the Installation Instructions that are
provided with these devices.

MMF-300 Monitor Module

An addressable module that monitors either a Style B (Class B) or Style D (Class A) circuit of dry-contact
input devices.

IDC Return –
IDC Return +

Areas used to record the device

address and SLC number.

SLC–

SLC+

IDC Out +

IDC Out -

FMMtpH.wmf

Rotary
Switches

Figure 16 MMF-300 Monitor Module

MMF-302 Monitor Module

Similar to the MMF-300, except it is used to monitor a single IDC of UL listed compatible two-wire 24
volt conventional smoke detectors. Refer to the Device Compatibility Document.

24 VDC –

24 VDC +
IDC Return –
IDC Return +

IDC Out +

IDC Out -

SLC–
SLC+

Rotary
Switches

Areas used to record the device

address and SLC number.

FZMtpH.wmf

Figure 17 MMF-302 Module

The SLC Wiring Manual PN 51309:K 2/14/08 25

Monitor Modules Descriptions

MDF-300 Dual Monitor Module

Similar to the MMF-300 but provides for two independent 2-wire IDCs at two separate, consecutive
addresses.

Rotary
Switches

Address +1

Base Address {

9 H–

{

8 H+

7L+

SLC–
SLC+

6L–

Areas used to record the device

address and SLC number.

SLCDualMod-simplified.wmf

Figure 18 Dual Monitor Module

MMF-301 Monitor Module

Functionally and electrically identical to an MMF-300, but offered in a smaller package for mounting
directly in the electrical box of the Style B (Class B) device being monitored.

Rotary Switches

IDC (+)

IDC (-)

15

1

14

9

8

TENS

2

3

LOOP

4

5

6

7

13
12
11

10

9

ONES

0

7

8

ADDRESS

0

Label – Use to record

1

the device address and

2

3

SLC number.

4

5

6

FMM-101.cdr

SLC (+)

SLC (-)

Figure 19 MMF-301 Module

26

The SLC Wiring Manual PN 51309:K 2/14/08

Descriptions Monitor Modules

–

–

–

–

–

–

MMF-300-10

A monitor module intended to interface between the FACP and up to ten (10) Style B (Class B) or five
(5) Style D (Class A) IDCs containing normally open contact devices.

This type of module is contained in either a BB-2 or BB-6 cabinet. The BB-2 can accommodate up to 2
modules and the BB-6, which requires the CH-6 chassis, can accommodate up to 6 modules.

See the Installation Instructions provided with module for proper installation into cabinet.

T5

– +

– +

– +

– +

– +– +

+

+

+

+

+

+

T0

T1

A/B SELECTCLDISABLE 1

DISABLE 2

T2

T3

J1

T4

4

3

2

5

1

0

15

14

0

6

BASE ADDRESS

7

8

9

13

10

12

11

SW1

4

3

2

5

1

6

7

8

9

+9

+0 +1

+2 +3

+4 +5

+6 +7

+8

Style Y or Style Z Select

Remove shunt for Style Z circuits

Disable Address

Place shunt in:
Disable 1 position to disable highest module address

SLC Address

Set rotary switches to base
(first) address of modules

Disable 2 position to disable highest two module addresses

Figure 20 MMF-300-10 Module

The SLC Wiring Manual PN 51309:K 2/14/08 27

Monitor Modules Descriptions

–

–

–

–

–

–

MMF-302-6

A monitor module intended to interface between the FACP and a conventional alarm system with up to
six (6) Style B (Class B) or three (3) Style D (Class A) IDCs containing normally open contact devices.

This type of module is contained in either a BB-2 or BB-6 cabinet. The BB-2 can accommodate up to 2
modules and the BB-6, which requires the CH-6 chassis, can accommodate up to 6 modules.

See the Installation Instructions provided with module for proper installat ion into cabinet.

– +

– +

J1

T0

T1

T6

A/B SELECT

A/B SELECT

DISABLE 1

DISABLE 2

T2

– +– +

+

T5

+

T3

+

+

T4

+

+

4

3

2

5

1

0

15

14

1

0

6

BASE ADDRESS

7

8

9

13

10

12

11

SW1

4

3

2

5

6

7
8

9

BASE ADDRESS +0 BASE ADDRESS +1 BASE ADDRESS +2

BASE ADDRESS +3

BASE ADDRESS +4 BASE ADDRESS +5

Style Y or Style Z Select

Remove shunt for Style Z circuits

Disable Address

Place shunt in:
Disable 1 position to disable highest module address

SLC Address

Set rotary switches to base
(first) address of modules

Disable 2 position to disable highest two module addresses

Figure 21 MMF-302-6 Module

28

The SLC Wiring Manual PN 51309:K 2/14/08

Installation Monitor Modules

Installation

When installing any of these modules DO NOT mix the following services that the IDC provides:

• Fire alarm service

• Automatic and manual waterflow alarm service with normally open contact devices

• Sprinkler supervision with norm ally open contact devices

Setting an SLC address for a Single Point Module

Each module can be set to one of 159 addresses (01-159) and is factory preset with an address of “00”.

Note: The MS-9050UD can support addresses 01 - 50. The MS-9200, MS-9200UD and MS-9200UDLS can support
module addresses of 01 - 99. The MS-9600, MS-9600LS, MS-9600LSC and MS-9600UDLS can support module
addresses 01 - 159.

T o set an SLC address, use a screwdriver to adjust the rotary switches on the module to the desired address.
The module below is set at “35”. When finished, mark the address on the module face in the place provided.

Breakaway Tab - Modules come with

a raised breakaway tab on the TENS

rotary switch. This tab must be

removed when the module is on an

Legacy Version

Module Rorary

Switch

FACP that uses more than 99
addresses.

Newer Version
Module Rotary

Switch

Figure 22 Setting SLC Address on a Single Point Module

Dual monitor modules: On dual monitor modules, only even
numbers appear on the ONES rotary switch. The module takes
both the selected address and the next-higher address.

SLC-setadd.cdr,SLC-setaddtpH.wmf, SLCbrktabs.wmf

The SLC Wiring Manual PN 51309:K 2/14/08 29

Monitor Modules Installation

Setting an SLC address for a Multi-Point Module

In Class B operation, each MMF-300-10, MMF-302-6, CMF-300-6 and CRF-300-6 module is set to a base
address. The remaining module points are automatically assigned to the next higher SLC addresses. For
example, if the base address of a MMF-300-10 is set to 28, the next module points will be addressed to
29, 30, 31, 32, 33, 34, 35, 36 and 37.

In Class A operation, alternate module points are paired together, resulting in a total of five module points.
For example, if the base address of a MMF-300-10 is set to 28, then 30, 32, 34 and 36 will be automatically
assigned to the remaining module points and 29, 31, 33, 35 and 37 are available for use by other modules.

Note: The MS-9050UD can support addresses 01 - 50. The MS-9200, MS-9200UD and MS-9200UDLS can support
module addresses of 01 - 99. The MS-9600, MS-9600LS, MS-9600LSC and MS-9600UDLS can support module
addresses 01 - 159 (the plastic stop located on the Tens switch must be removed to set addresses above 99).

T o set an SLC address, use a common screwdriver to adjust the rotary switches on the module to the desired
address. The module below is set at “28”.

4

3

2

Rotary Switches

1

0
15

14

1

0

13

5

6

7

TENS

8

9

10

12

11

4

3

2

5

6

8

9

7

Plastic Stop

ONES

multroty.cdr

Figure 23 Setting SLC Address on a Multi-Point Module

30

The SLC Wiring Manual PN 51309:K 2/14/08

MMF-300 Wiring Diagrams Monitor Modules

MMF-300 Wiring Diagrams

Following are wiring diagrams that depict NFPA Style B (Class B) and D (Class A) Initiating Device
Circuits (IDCs) using MMF-300 monitor modules.

The Initiating Device Circuit (IDC) is supervised and current-limited to 210 microamperes @ 24 VDC
(nominal).

Wiring a NFPA Style B IDC with an MMF-300

Connect the SLC wiring to the module terminals 1 (–) and 2 (+).
Each module takes one address on the SLC. Use the rotary switches on the module to set it to the required

SLC address. Refer to “Setting an SLC address for a Single Point Module” on page 29.
The figure below shows typical wiring for a supervised and power-limited NFPA Style B IDC using an

MMF-300 module.

• Refer to the Device Compatibility Document for compatible smoke detectors.

• See "Appendix A: Power Considerations" on page 53 for information on supervising 24 VDC
power.

From Supply

Manual pull
station

SLC-idcB1tpH.wmf

Heat
detector

24 VDC
Four-wire
Detector Base

47K ELR
(supplied
with module)

MMF-300

IDC

24 VDC Power
Filtered, Regulated,
Resettable

To Next IDC
or
Supervision Device

SLC

Figure 24 Typical Style B IDC Wiring with MMF-300

The SLC Wiring Manual PN 51309:K 2/14/08 31

Monitor Modules MMF-300 Wiring Diagrams

Wiring a NFPA Style D IDC with an MMF-300

Connect the SLC wiring to the module terminals 1 (–) and 2 (+).
Each module takes one address on the SLC. Use the rotary switches on the module to set it to the required

SLC address. Refer to “Setting an SLC address for a Single Point Module” on page 29.
The figure below shows typical wiring for a supervised and power-limited NFP A S tyle D (Class A) IDC

using an MMF-300 module.

• Refer to the Device Compatibility Document for compatible smoke detectors.

• See "Appendix A: Power Considerations" on page 53 for information on supervising 24 VDC
power.

From
Supply

24 VDC
Four-wire
Detector Base

Manual pull
station

24 VDC Power
Filtered, Regulated,
Resettable

To Next IDC
or
Supervision Device

Heat
detector

SLC

MMF-300

IDC

SLC-idcD1tpH.wmf

Figure 25 Typical Style D IDC Wiring with MMF-300

32

The SLC Wiring Manual PN 51309:K 2/14/08

MMF-300-10 Wiring Diagrams Monitor Modules

–

–

–

–

–

–

–

–

–

–

MMF-300-10 Wiring Diagrams

Following are wiring diagrams that depict NFPA Style B (Class B) and D (Class A) Initiating Device
Circuits (IDCs) using MMF-300-10 monitor modules.

The Initiating Device Circuit (IDC) is supervised and current-limited to 1.0 milliampere @ 24 VDC
(nominal).

Wiring a NFPA Style B IDC with an MMF-300-10

Connect the SLC wiring to the module terminals T5 as shown below.
Use the rotary switches on the module to set the base SLC address. Each module takes ten addresses on

the SLC. The remaining module points are automatically assigned to the next nine higher addresses. Refer
to “Setting an SLC address for a Multi-Point Module” on page 30.

DO NOT set the lowest address above 150 (41 for the MS-9050UD, 90 for the MS-9200, MS-9200UD
and MS-9200UDLS), as the other module points will be assigned to nonexistent addresses.

The figure below shows typical wiring for a supervised and power-limited NFPA Style B IDC using an
MMF-300-10 module.

• Refer to the Device Compatibility Document for compatible smoke detectors.

• See "Appendix A: Power Considerations" on page 53 for information on supervising 24 VDC
power.

+

–

+

–

24 VDC Four-wire
Detector Base

47K ELR
(supplied
with module)

24 VDC Power
Filtered, Regulated, Resettable

+

Heat

Detector

+

T3

SLC

T5

Manual Pull

Station

MMF-300-10

– +– +

+

+

+

+

+

T1T0

T2

Figure 26 Typical Style B IDC Wiring with MMF-300-10

+

+

T4

IDC
Out

+

SLC-idcB4.cdr

The SLC Wiring Manual PN 51309:K 2/14/08 33

Monitor Modules MMF-300-10 Wiring Diagrams

–

–

–

–

–

–

–

–

–

–

Wiring a NFPA Style D IDC with an MMF-300-10

Connect the SLC wiring to the module terminals T5 as shown below.
Use the rotary switches on the module to set the base SLC address. Each module takes five alternating

addresses on the SLC. The remaining module points are automatically assigned to the next four higher
addresses. (Example: 28, 30, 32, 34 and 36). Refer to “Setting an SLC address for a Multi-Point Module”
on page 30.

DO NOT set the lowest address above 150 (41 for the MS-9050UD, 90 for the MS-9200, MS-9200UD
and MS-9200UDLS), as the other module points will be assigned to nonexistent addresses.

The figure below shows typical wiring for a supervised and power-limited NFP A S tyle D (Class A) IDC
using an MMF-300-10 module.

• Refer to the Device Compatibility Document for compatible smoke detectors.

• See "Appendix A: Power Considerations" on page 53 for information on supervising 24 VDC
power.

24 VDC Power
Filtered, Regulated, Resettable

+

–

+

–

24 VDC Four-wire
Detector Base

SLC

T5

Manual Pull

Station

MMF-300-10

– +– +

+

+

+

+

+

T1T0

T2

+

Detector

+

T3

Figure 27 Typical Style D IDC Wiring with MMF-300-10

Heat

IDC

Return

+

+

IDC
Out

+

SLC-idcD3.cdr

T4

34

The SLC Wiring Manual PN 51309:K 2/14/08

MDF-300 Wiring Diagrams

Following is a wiring diagrams that depict NFP A Style B (Class B) Initiating Device Circuits (IDCs) using
MDF-300 dual monitor module.

Wiring a NFPA Style B IDC with an MDF-300

Connect the SLC wiring to the module terminals 1 (–) and 2 (+).
Use the rotary switches on the module to set it to the SLC address. Each dual module takes two addresses

on the SLC. Circuit ‘L ’ corresponds to the address set on the rotary switches, which will be an even number.
Circuit ‘H’ will automatically respond to the next higher address, which will be an odd number. Use caution
to avoid duplicate addressing of modules on the system. Refer to “Setting an SLC address for a Single Point
Module” on page 29.

Each IDC (H & L) is power limited to 230 microamperes @ 24 VDC.
The figure below shows typical wiring for a supervised and power-limited NFPA Style B IDC using an

MDF-300 module.

• Refer to the Device Compatibility Document for compatible smoke detectors.

• See "Appendix A: Power Considerations" on page 53 for information on supervising 24 VDC
power.

SLC-idcB3fdm1.wmf

Manual
Pull
Station

Heat
Detector

Base Address
(IDC Circuit L)

Manual
Pull
Station

47K
ELR

Base +1 Address
(IDC Circuit H)

47K
ELR

MDF-300

Figure 28 Typical Style B IDC Wiring with MDF-300

SLC

The SLC Wiring Manual PN 51309:K 2/14/08 35

Monitor Modules MMF-302 Wiring Diagrams

MMF-302 Wiring Diagrams

Following are wiring diagrams that concern NFPA Style B (Class B) and D (Class A) Initiating Device
Circuits (IDCs) using MMF-302 monitor modules.

Wiring a NFPA Style B IDC with an MMF-302

Connect the SLC wiring to the module terminals 1 (–) and 2 (+).
Each module takes one address on the SLC. Use the rotary switches on the module to set it to the required

SLC address. Refer to “Setting an SLC address for a Single Point Module” on page 29.
The IDC is supervised and power limited to 230 microamperes @ 24 VDC.
The figure below shows typical wiring for a supervised and power-limited NFPA Style B IDC using an

MMF-302 module.

• Refer to the Device Compatibility Document for compatible smoke detectors.

• 24 VDC power must be provided from a UL listed power supply for fire protection use. This power
is inherently supervised by the module.

• See "Appendix A: Power Considerations" on page 53 for information on 24 VDC power.

24 VDC Resettable power.

Two-wire
smoke
detectors

3.9K ELR
(supplied with module)

IDC

90 mA External 24 volt

supply required

MMF-302

Figure 29 Typical Style B IDC Wiring with MMF-302

SLC

SLC-idcB2tpH.wmf

36

The SLC Wiring Manual PN 51309:K 2/14/08

MMF-302 Wiring Diagrams Monitor Modules

Wiring a NFPA Style D IDC with an MMF-302

Connect the SLC wiring to the module terminals 1 (–) and 2 (+).
Each module takes one address on the SLC. Use the rotary switches on the module to set it to the required

SLC address. Refer to “Setting an SLC address for a Single Point Module” on page 29.
The figure below shows typical wiring for a supervised and power-limited NFPA Style D (Class A) IDC

using an MMF-302 module.

• Refer to the Device Compatibility Document for compatible smoke detectors.

• 24 VDC power must be provided from a UL listed power supply for fire protection use. This power
is inherently supervised by the module.

• See "Appendix A: Power Considerations" on page 53 for information on 24 VDC power.

Two-wire
smoke
detectors

24 VDC Resettable power.
90 mA External 24 volt supply required

MMF-302

IDC

3.9K ELR
(supplied with module)

Figure 30 Typical Style D IDC Wiring with MMF-302

SLC

SLC-idcD2tpH.wmf

The SLC Wiring Manual PN 51309:K 2/14/08 37

Monitor Modules MMF-302-6 Wiring Diagrams

–

–

–

–

–

–

–

–

MMF-302-6 Wiring Diagrams

Following are wiring diagrams that concern NFPA Style B (Class B) and D (Class A) Initiating Device
Circuits (IDCs) using MMF-302-6 monitor modules.

Wiring a NFPA Style B IDC with an MMF-302-6

Connect the SLC wiring to the module terminals T0 as shown below.
Use the rotary switches on the module to set the base SLC address. Each module takes six addresses on

the SLC. The remaining module points are automatically assigned to the next five higher addresses. Refer
to “Setting an SLC address for a Multi-Point Module” on page 30.

DO NOT set the lowest address above 154 (45 for the MS-9050UD, 94 for the MS-9200, MS-9200UD
and MS-9200UDLS), as the other module points will be assigned to nonexistent addresses.

The figure below shows typical wiring for a supervised and power-limited NFPA Style B IDC using an
MMF-302-6 module.

• Refer to the Device Compatibility Document for compatible smoke detectors.

• 24 VDC power must be provided from a UL listed power supply for fire protection use. This power
is inherently supervised by the module.

• See "Appendix A: Power Considerations" on page 53 for information on 24 VDC power.

+

–

+

–

SLC

3.9K ELR
(supplied with
module)

+

–

Figure 31 Typical Style B IDC Wiring with MMF-302-6

24 VDC resettable power

T1

T0

– +

– +

Two-wire smoke detectors

MMF-302-6

T2

+

+

+

+

IDC
Out

T3

+

+

+

T4

+

SLC-idcB5.cdr

38

The SLC Wiring Manual PN 51309:K 2/14/08

MMF-302-6 Wiring Diagrams Monitor Modules

–

–

–

–

–

–

–

–

Wiring a NFPA Style D IDC with an MMF-302-6

Connect the SLC wiring to the module terminals T0 as shown below.
Use the rotary switches on the module to set it to the SLC addresses. Each module takes three alternating

addresses on the SLC. The remaining module points are automatically assigned to the next two higher
addresses. (Example: 28, 30 and 32). Refer to “Setting an SLC address for a Multi-Point Module” on page

30.

DO NOT set the lowest address above 154 (45 for the MS-9050UD, 94 for the MS-9200, MS-9200UD
and MS-9200UDLS), as the other module points will be assigned to nonexistent addresses.

The figure below shows typical wiring for a supervised and power-limited NFPA Style D (Class A) IDC
using an MMF-302-6 module.

• Refer to the Device Compatibility Document for compatible smoke detectors.

• 24 VDC power must be provided from a UL listed power supply for fire protection use. This power
is inherently supervised by the module.

• See "Appendix A: Power Considerations" on page 53 for information on 24 VDC power.

Two-wire smoke detectors

+

–

+

–

SLC

24 VDC resettable power

+

–

MMF-302-6

– +

– +

T1

T0

+

+

T2

+

Figure 32 Typical Style D IDC Wiring with MMF-302-6

+

T3

+

Return

+

IDC

+

IDC
Out

T4

+

SLC-idcD4.cdr

The SLC Wiring Manual PN 51309:K 2/14/08 39

Control Modules Description

Control Modules

When using a Control Module as a Notification Appliance Circuit (NAC), the isolation described in the
section titled SLC Circuits with Isolators which begins on page 21, is required or Riser Conductors must
be installed in accordance with the survivability from attack by fire requirements in National Fire Alarm
Code, NFPA 72.

Description

The CMF-300 and CMF-300-6 modules are addressable modules that can be used for monitoring and
switching 24 VDC Notification Appliance Circuit (NAC) power for NFPA S tyle Y (Class B) and NFPA
Style Z (Class A) circuits.

Ratings for the relay contacts on the module are:

Load Description Application Maximum Voltage Current Rating

Resistive Non-Coded 30 VDC 3.0 A
Resistive Coded 30 VDC 2.0 A
Resistive Non-Coded 110 VDC 0.9 A
Resistive Non-Coded 125 VAC (CMF-300)

70.7 VAC (CMF-300-6)
Inductive (L/R = 5ms) Coded 30 VDC 0.5 A
Inductive (L/R = 2ms) Coded 30 VDC 1.0 A
Inductive (PF = 0.35) Non-Coded 125 VAC (CMF-300)

70.7 VAC (CMF-300-6)

0.9 A

0.5 A

Note: For more information on module specifications, refer to the Installation Instructions provided with these devices.

CMF-300 Installation

Setting an SLC address for an CMF-300 Module

Each module is factory preset with an address of “00”. To set an SLC address refer to "Setting an SLC
address for a Single Point Module" on page 29.

Wiring a Notification Appliance Circuit (NAC) with an CMF-300

The figure below shows the connections to wire a module for powering a 24 VDC NAC:

24 VDC Nonresettable Power (–)*
24 VDC Nonresettable Power (+)*

Style Z NAC (+)
Style Z NAC (–)

Style Y/Z NAC (–)
Style Y/Z NAC (+)

NOTE: Module polarities are shown in alarm condition.

SLC (–)
SLC (+)

40

SLCModule-simplified.wmf

Figure 33 CMF-300 Wiring Connections

The SLC Wiring Manual PN 51309:K 2/14/08

Wiring a CMF-300 Module Control Modules

Wiring a CMF-300 Module

This section contains instructions and diagrams for wiring a Signaling Line Circuit with a CMF-300 as
a Notification Appliance Circuit (NAC).

Wiring a Style Y NAC (Two-Wire)

A supervised and power-limited NFP A Style Y (Class B) NAC using a CMF-300 module. Polarized alarm
notification appliances are shown connected to the module in a two-wire configuration.

Note: Refer to Device Compatibility Document for compatible notification appliances and relays.

• See "Appendix A: Power Considerations" on page 53 for information on monitoring 24 VDC power.

• Each module can control 2 amps of resistive load (on electronic devices) or 1 amp of inductive load
(on mechanical bells and horns).

• 24 VDC power must be provided from a UL listed power supply for fire protecti on use.

• A power supervision relay is required only on the last module of the power run.

• Do not T-tap or branch a St yle Y circuit.

• Terminate the circuit across the last device using an End-of-Line Resistor 47K, 1/2-watt,
P/N SSD A2143-00 (ELR-47K in Canada).

• Do not loop wiring under the screw te rminals of any notification appliance. To maintain
supervision, break the wire run at each device

SLC

24 VDC Nonresettable power

ELR

47K, 1/2-watt

24 VDC Notification

Appliances

CMF-300

NOTE: A power
supervision relay is
required only on the
last module of the
power run.

NAC

Note: Module polarities are shown in alarm condition

Figure 34 NFPA Style Y Notification Appliance Circuit

SLC-nacY.wmf

The SLC Wiring Manual PN 51309:K 2/14/08 41

Control Modules Wiring a CMF-300 Module

Wiring a Style Z NAC (Four-Wire)

A supervised and power-limited NFPA S tyle Z (Class A) NAC using a CMF-300 module. Polarized alarm
notification appliances are shown connected to the module in a four-wire configuration.

Note: Refer to the Device Compatibility Document for compatible notification appliances and relays.

• See "Appendix A: Power Considerations" on page 53 for information on monitoring 24 VDC power.

• Each module can control 2 amps of resistive load (on electronic devices) or 1 amp of inductive load
(on mechanical bells and horns).

• 24 VDC power must be provided from a UL listed power supply for fire protecti on use.

• A power supervision relay is required only on the last module of the power run.

• Do not T-tap or branch a Style Z circuit.

• Do not loop wiring under the screw te rminals of any notification appliance. To maintain
supervision, break the wire run at each device.

NOTE: A power supervision relay is required only
on the last module of the power.

24 VDC Nonresettable power

24 VDC
notification
appliances

NAC Return

NAC Out

Note: Module polarities are shown in alarm condition.

Figure 35 NFPA Style Z Notification Appliance Circuit

SLC

CMF-300

SLC-nacZtpH.wmf

42

The SLC Wiring Manual PN 51309:K 2/14/08

CMF-300-6 Installation

Cabinet Installation

This type of module is contained in either a BB-2 or BB-6 cabinet. The BB-2 can accommodate up to 2
modules and the BB-6, which requires the CH-6 chassis, can accommodate up to 6 modules.

See the Installation Instructions provided with module for proper installation into cabi net.

Setting an SLC address for an CMF-300-6 Module

In “Style Y” operation each CMF-300-6 module can be set to one of 154 base addresses (01-154). The
remaining module points are automatically assigned to the next five higher SLC addresses. For example,
if the base address is set to 28, the next five module points will be addressed to 29, 30, 31, 32 and 33.

In “Style Z” operation alternate module points are paired together, resulting in a total of three module points.
For example, if the base address is set to 28, then 30 and 32 will be automatically assigned to the remaining
module points and 29, 31 and 33 are available to be used for other modules on the SLC.

DO NOT set the lowest address above 154 (45 for the MS-9050UD, 94 for MS-9200, MS-9200UD and
MS-9200UDLS), as the other module points will be assigned to nonexistent addresses.

Note: The MS-9050UD can support addresses 01 - 50. The MS-9200, MS-9200UD and MS-9200UDLS can support
module addresses of 01 - 99. The MS-9600, MS-9600LS, MS-9600LSC and MS-9600UDLS can support module
addresses 01 - 159.

T o set an SLC address, use a common screwdriver to adjust the rotary switches on the module to the desired
address. See Figure 36 on page 44.

Note: For use with MS-9600, MS-9600LS, MS-9600LSC and MS-9600UDLS, remove the stop on the upper rotary
switch.

Setting NACs as Style Y or Style Z

To use this module for Style Y (Class B) operation ascertain that a small shunt is installed on the “A/B
SELECT” set of pins. (As shipped).

T o use this module for St yle Z (Class A) operation remove the small shunt from the “A/B SELECT” set
of pins. See drawing below and Figure 36 on page 44.

Disabling Unused Module Addresses

A shunt is used, in conjunction with a pin block, to disable a maximum of three
(3) unused module addresses. If two module addresses are disabled, the lowest
four addresses will be functional, while the highest two will be disabled. For
example, if the shunt is placed on ‘DISABLE 2’ and the base address is set to
28, the module addresses will be assigned to 28, 29, 30 and 31.

In Style Z operation, placing a small shunt on ‘DISABLE 3’ will disable all
three addresses. Placing it on ‘DISABLE 2’ will disable two out of three
addresses.

To disable addresses, securely place one of the supplied small shunts onto the desired set of pins. See
drawing and Figure 36 on page 44.

DISABLE 3

DISABLE 2

A/B SELECT

DISABLE 1

J1

Short Circuit Protection

Protection is disabled for each module address when there is a large shunt installed on the corresponding
pins of the pin block (as shipped, all six addresses are disabled).

SLC-disable1.cdr

When enabled, the module will not switch power supply if a short circuit condition exists on a NAC.
T o enable “Short Circuit Protection” for an address, remove the large shunt from the corresponding pins

of the pin block. See Figure 36 on page 44. Place unused shunts on single pin to store on board for future use.

The SLC Wiring Manual PN 51309:K 2/14/08 43

Control Modules CMF-300-6 Installation

Features Not Supported

The “Synchronization” and “Power Supply Monitoring” features are not supported at this time.

Circuit Board Information

Status Indicators

Green LEDs are
controlled by FACP
to indicate status of
each module address.

Synchronization Generator

-Not Supported. DO NOT

remove shunts.

T0

+0

T10

– +

– +

– +

– +

T1

+1

T12 T13

T11

ENABLE POWER SUPPLY MONITORS

A/B SELECT

DISABLE 1

DISABLE 2

DISABLE 3

DISABLE SHORT CIRCUIT PROTECTION

#1 #2 #3 #4 #5 #6

J1

BASE ADDRESS +0 BASE ADDRESS +1 BASE ADDRESS +2

– +

– +

T2

+2

SYNC GENERATOR

BASE ADDRESS +3

– +– +

T3

+3

Power Supply Monitors -

Not Supported. DO NOT
remove shunts.

– +– +

T4 T5

+4

T14

T15

T16

4

3

2

1

0
15

14

13

12

11

4

3

2

1

0

BASE ADDRESS +4 BASE ADDRESS +5

– +– +

+5

5

6

7
8

9

10

SW1

5

6

7
8

9

BASE ADDRESS

CMF-300-6.cdr

44

Place shunt onto required pins.

Disable Address -

Select

Style Y (Class B) or

Style Z (Class A) -

Remove shunt for Style Z (Class A).

Figure 36 CMF-300-6 Control Module Settings

SLC Address

Set rotary switches to
address required.

Short Circuit Protection - Remove
shunt from the corresponding pins to
enable. Shunt #1 for first address, #2
for second address, etc.

The SLC Wiring Manual PN 51309:K 2/14/08

Wiring a CMF-300-6 Module

This section contains basic instructions and diagrams for wiring a Signaling Line Circuit with a CMF-300­6 as a Notification Appliance Circuit (NAC).

For more detailed information on wiring a CMF-300-6 Control Module refer to the Installation Instructions
provided with the module. Included in these instructions are wiring diagrams concerning a single power
supply being shared by multiple NACs and audio NAC configurations.

Wiring a Style Y NAC (Two-Wire)

A supervised and power-limited NFPA S tyle Y (Class B) NAC with a single power supply dedicated to
a single NAC using a CMF-300-6 module. Polarized alarm notification appliances are shown connected
to the module in a two-wire configuration.

Note: Refer to Device Compatibility Document for compatible notification appliances and relays.

• See "Appendix A: Power Considerations" on page 53 for information on monitoring 24 VDC power.

• Each module can control 2 amps of resistive load (on electronic devices) or 1 amp of inductive load

(on mechanical bells and horns).

• 24 VDC power must be provided from a UL listed power supply for fire protecti on use.

• A power supervision relay is required only on the last module of the power run.

• Do not T-tap or branch a St yle Y circuit.

• Terminate the circuit across the last device using an End-of-Line Resistor 47K, 1/2-watt,

P/N SSD A2143-00 (ELR-47K in Canada).

• Do not loop wiring under the screw te rminals of any notification appliance. To maintain

supervision, break the wire run at each device.

ELR 47K,
1/2-watt

Power Supervision
Relay
(EOLR-1)

SLC

24 VDC
nonresettable
power

24 VDC notification appliances

–

+

NAC Out

–

– +– +

+

T15

– +– +

T5

+5

T16

Relay Connector Assembly

CMF-300-6

T0
+0

– +

– +

T10

– +

– +

T1

+1

T11

T12

– +– +

T2

+2

T13

– +– +

T3 T4

+3 +4

T14

Figure 37 NFPA Style Y Notification Appliance Circuit

The SLC Wiring Manual PN 51309:K 2/14/08 45

SLC-nacY2.cdr

Control Modules Wiring a CMF-300-6 Module

Wiring a Style Z NAC (Four-Wire)

A supervised and power-limited NFPA Style Z (Class A) NAC with a single power supply dedicated to
a single NAC using a CMF-300-6 module. Polarized alarm notification appliances are shown connected
to the module in a four-wire configuration.

Note: Refer to the Device Compatibility Document for compatible notification appliances and relays.

• See "Appendix A: Power Considerations" on page 53 for information on monitoring 24 VDC power.

• Each module can control 2 amps of resistive load (on electronic devices) or 1 amp of inductive load
(on mechanical bells and horns).

• 24 VDC power must be provided from a UL listed power supply for fire protecti on use.

• A power supervision relay is required only on the last module of the power run.

• Do not T-tap or branch a Style Z circuit.

• Do not loop wiring under the screw te rminals of any notification appliance. To maintain
supervision, break the wire run at each device.

Power Supervision
Relay
(EOLR-1)

24 VDC
nonresettable
power

+

–

+

–

24 VDC notification appliances

T0
+0

SLC

T10

– +

– +

CMF-300-6

– +

– +

T1

+1

T12

T11

Power Supply Jumper

– +

T2

+2

– +

T13

Relay Connector Assembly

NAC

Return

+

– +– +

T3 T4

+3 +4

T14

Figure 38 NFPA Style Z Notification Appliance Circuit

–

– +– +

NAC

Out

+

T15

T16

–

–

– +– +

T5

+5

+

SLC-nacZ3.cdr

46

The SLC Wiring Manual PN 51309:K 2/14/08

Description

Relay Modules

The CRF-300 and the CRF-300-6 modules are addressable modules that provides Form-C relay contacts.
Ratings for the relay contacts on the module are:

Load Description Application

Resistive Non-Coded 30 VDC 3.0 A
Resistive Coded 30 VDC 2.0 A
Resistive Non-Coded 110 VDC 0.9 A
Resistive Non-Coded 125 VAC 0.9 A
Inductive (L/R = 5ms) Coded 30 VDC 0.5 A
Inductive (L/R = 2ms) Coded 30 VDC 1.0 A
Inductive (PF = 0.35) Non-Coded 70.7 VAC 0.7 A
Inductive (PF = 0.35) Non-Coded 125 VAC 0.5 A

Note: For more information on the module specifications refer to the Installation Instructions provided with these
devices.

CRF-300 Installation & Wiring

Setting an SLC address for a CRF-300 Module

Each module is factory preset with an address of “00.” To set an SLC address refer to "Setting an SLC
address for a Single Point Module" on page 29.

Wiring a CRF-300 Module (Form-C Relay)

The figure below shows a CRF-300 module wired to the Control Panel:

CRF-300

Maximum

Voltage

SLC

Current

Rating

C

NC

NO

C

NC

NO

SLC-frmCtpH.wmf

Figure 39 CRF-300 Wiring Connections

The SLC Wiring Manual PN 51309:K 2/14/08 47

Relay Modules CRF-300-6 Circuit Board Information

A
A

A
A

CRF-300-6 Circuit Board Information

T102

– +– +

4

3

2

5

1

14

1

6

B

7

8

SE

9

13

10

12

11

4

3

2

SW1

5

9

DDRESS

6

7
8

Disable Address

Place shunt onto
required pins.

J1

THREE

NONE

TWO

ONE

DIS

DDRESS

BLE

0

15

0

Status Indicators

Green LEDs are
controlled by FACP
to indicate status of
each module address.

SLC Address

Set rotary switches
to address required.

48

Figure 40 CRF-300-6 Control Relay Module

The SLC Wiring Manual PN 51309:K 2/14/08

CRF-300-6 Installation & Wiring

Cabinet Installation

This type of module is contained in either a BB-2 or BB-6 cabinet. The BB-2 can accommodate up to 2
modules and the BB-6, which requires the CH-6 chassis, can accommodate up to 6 modules.

See the Installation Instructions provided with module for proper installation into cabi net.

Setting an SLC address for a CRF-300-6 Module

Each CRF-300-6 module can be set to one of 154 base addresses (01-154). The remaining module points
are automatically assigned to the next five higher SLC addresses. For example, if the base address is set
to 28, the next five module points will be addressed to 29, 30, 31, 32 and 33.

DO NOT set the lowest address above 154 (45 for the MS-9050UD, 94 for MS-9200, MS-9200UD and
MS-9200UDLS), as the other module points will be assigned to nonexistent addresses.

Note: The MS-9050UD can support addresses 01 - 50. The MS-9200, MS-9200UD and MS-9200UDLS can support
module addresses of 01 - 99. The MS-9600, MS-9600LS, MS-9600LSC and MS-9600UDLS can support module
addresses 01 - 159. T o set an SLC address, use a common screwdriver to adjust the rotary switches on the module to
the desired address. See Figure 36 on page 44.

Note: For use with a MS-9600, MS-9600LS, MS-9600LSC and MS-9600UDLS, remove the stop on the upper rotary
switch.

Disabling Unused Module Addresses

A shunt is provided on the circuit board to disable a maximum of three (3)
unused module addresses. If two module addresses are disabled, the lowest four
addresses will be functional, while the highest two will be disabled. For
example, if the shunt is placed on ‘TWO’ and the base address is set to 28, the
module addresses will be assigned to 28, 29, 30 and 31.

T o disable addresses, remove the shunt from it’s storage location and securely
place it onto the desired set of pins. See illustration.

Wiring a CRF-300-6 Module (Form-C Relay)

The figure below shows a CRF-300-6 module wired to the Control Panel.

SLC Out

+

SLC In

–

+

Relay Connections

–

CRF-300-6

J1

SLC-disable2.cdr

Shunt Storage
Location

– +

– +

SLC-fmC1.cdr

Figure 41 CRF-300-6 Wiring Connections

The SLC Wiring Manual PN 51309:K 2/14/08 49

Description

Intelligent Detector Bases

The following bases provide connection between the SLC and these detector heads:

• AD350 and AD355 Multicriteria Photoelectric Smoke Det ector

• CP350 and CP355 Ionization Smoke Detector

• H350, H350R, H355, H355R and H355HT Thermal Detector

• SD350, SD350T, SD355 and SD355T Photoelectric Smoke Detector

The B350LP Detector Base is a standard plug-in base provided with each detector head.
The B501BH Sounder Detector Base includes a horn that will sound when the sensor’s visible LEDs are

latched on for approximately 10 seconds.

On the MS-9200 control panel, the sounder will activate when the sensor’s visible LEDs are
latched on for approximately 10 seconds (Alarm Verification does not delay sounder).

If the MS-9600, MS-9600LS, MS-9600LSC, MS-9600UDLS, MS-9200UD, MS-9200UDLS or
MS-9050UD control panel is set with Alarm Verification ON , the sounder will activate at the end
of the verification cycle, providing an alarm is verified, approximately 10 seconds after the sensor’s
LEDs are latched on. If Alarm Verification is OFF, the sounder will activate when the sensor’s
visible LEDs are latched on for approximately 10 seconds.

The B224RB Relay Detector Base includes Form-C latching relay contacts for the control of an auxiliary
function. The relay operates 12 seconds (nominally) after activation of the sensor head remote annunciator
output.

The B224RI Isolator Detector Base prevents an entire communications loop from being disabled when
a short circuit occurs.

Note: For more information refer to the Installation Instructions document provided with these devices.

Installation and Wiring

Setting the Detector Address

Each intelligent detector is factory preset with an address of “00.” To set an SLC address, use a common
screwdriver to adjust the rotary switches on the detector to the desired address (see "Setting an SLC address
for a Single Point Module" on page 29). When finished, mark the address in the place provided on the base
and the detector.

Wiring a Detector Base

T ypical wiring of a detector base (B350LP shown) connected to an SLC is shown in the figure below. An
optional RA400Z Remote LED Annunciator is shown connected to the detector.

+ –

From Control Panel SLC

2(+)

3

1(–)

–

To Next Device
on SLC

+

RA400Z

+ –

SLC-B350LPwiredr

Figure 42 Detector Terminal Block Wiring

50 The SLC Wiring Manual PN 51309:K 2/14/08

Description Addressable Beam Detectors

Addressable Beam Detectors

Description

The BEAM355 and BEAM355S are intelligent, addressable projected beam smoke detectors, designed
for protecting open areas with high and sloping ceilings and wide-open areas, where spot type smoke
detectors are difficult to install and maintain. The BEAM355S has an integral sensitivity test feature that
consists of a test filter attached to a servomotor inside the detector optics.

Note: This section provides basic wiring and addressing information. For critical information on device installation,
operation and alignment, refer to the Installation Instructions document provided with these devices.

Installation and Wiring

Setting an SLC Address for a Beam Detector

Each beam detector is factory preset with an address of “00.” To set an SLC address, use a common
screwdriver to adjust the address rotary code switches on the detector to the desired address (refer to
"Setting an SLC address for a Single Point Module" on page 29).

Wiring a Beam Detector

Typical wiring of a beam detector connected to an SLC is illustrated in the figure below.

Alignment Mirror
Alignment Gunsight
Alignment Position Indicator

Optics Lock-down Screws

ONES T ENS

ADDRESSING CODE

SWITCHE S

Style 7 Isolator Shunts

Test Option (-)

Test Option (+)

not used
not used

Digital Signal
Strength Readout

Horizontal Adjustment

Alignment Switch

Sensitivity Switch

T est Switch

Vertical Adjustment

Reset Switch

Remote Alarm Out

Reset Input

Test Input

Aux (-)

SLC (-) to next device
SLC (+) to next device
SLC (-) from panel or previous device
SLC (+) from panel or previous device

RTS451/KEY Connections

Figure 43 Beam Detector Terminal Block Wiring

The SLC Wiring Manual PN 51309:K 2/14/08 51

Addressable Manual Pull Station Description

–

Addressable Manual Pull Station

Description

The BG-12LX is an addressable manual pull station with a key-lock reset feature.

Note: For more information refer to the Installation Instructions document provided with this device.

Installation

Setting an SLC address

Each unit is factory preset with an address of “00.” To set an SLC address refer to "Setting an SLC address
for a Single Point Module" on page 29.

Wiring a Manual Pull Station

Typical wiring for a BG-12LX Manual Pull Station to an SLC:

+

SLC

To next device
on SLC

+

–

SLC-bg12lx.cdr

Figure 44 Wiring of an BG-12LX Pull Station to an SLC

52

The SLC Wiring Manual PN 51309:K 2/14/08

Supplying Power to 24 VDC Detectors Appendix A: Power Considerations

Appendix A: Power Considerations

Supplying Power to 24 VDC Detectors

Resistance and Size

T o determine the minimum resistance that can be tolerated in supplying power to 24 VDC 4-wire detectors,
use the calculation below . Use this resistance to select the proper gauge wire for the power run from the
manufacturers specifications for the desired wire.

Rmax =

Where:

Rmax = maximum resistance of the 24 VDC wires
Vom = minimum operating voltage of the detector or end-of-line relay, whichever is greater, in volts
N = total number of detectors on the 24 VDC supply circuit
Is = detector current in standby
Na = number of detectors on the 24 VDC power circuit which must function at the same time in alarm
Ia = detector current in alarm
Ir = end-of-line relay current

(18.1 - Vom)

(N)(Is) + (Na)(Ia) + (Ir)

The SLC Wiring Manual PN 51309:K 2/14/08 53

Supervising 24 VDC Power

Power used to supply 24 VDC notification appliances (using the CMF-300) can be supervised with a power
supervision relay . This relay, energized by the 24 VDC power itself, is installed at the end of each respective
power run and wired in-line with the supervised circuit of any intelligent module.

• 24 VDC power must be provided from a UL listed power supply for fire protecti on use.

When power is removed from the relay, the normally closed contacts open the supervised circuit, generating
a trouble condition. Therefore, the relay needs to be installed at the end of the supervised circuit, so as to
not disrupt the operating capability of all the devices on that circuit. The relay can be installed in-line with
any leg (+ or –) of the supervised NAC circuit, either a Style B (Class B) or a Style D (Class A) circuit.

The drawing below illustrates this concept.

24 VDC Power from
Control Panel or
Power Supply

Power Supervision

Relay

(EOLR-1)

Last device on the SLC loop

ELR
47K

Supervised NAC

ELR 47K

Power Supervision
Relay
(EOLR-1)

ELR 47K

SLC-psrtpH.cdr

Figure 45 Supervised 24 VDC Circuit

24 VDC Power from
Control Panel or Power Supply

CMF-300

Supervised NAC

MMF-300

SLC-psr-2addresstpH.wmf

Figure 46 Alternate: 2-Address Method of Supervising a 24 VDC Circuit

54 The SLC Wiring Manual PN 51309:K 2/14/08

Introduction Appendix B: Surge Suppression

Appendix B: Surge Suppression

Introduction

There are three (3) primary surge protectors that are approved for use with the MS-9200, MS-9200UD,
MS-9200UDLS, MS-9600, MS-9600LS, MS-9600LSC, MS-9600UDLS and MS-9050UD.

• DTK-2LVLP-F Diversified Technology Group, Inc. 1720 Starkey Rd. Largo, FL 33771 (727)

812-5000

• SLCP-030 EDCO 1805 N.E. 19th Ave. Ocala, FL 34470 [phone]

• PLP-42N Northern Technologies, Inc. 23123 E. Madison Ave. Liberty Lake, WA 99019 (800)

727-9119

Note: For detailed information refer to the installation documentation supplied with the unit.

One primary surge protector must be used with each SLC wiring pair whenever SLC wiring runs outside
the building.

• Install primary protection only as shown in this document .

• Refer to NEC Article 800 and local building code requirements.

Additional primary surge suppressors may be added as required by the NEC. Add these additional
suppressors in series with the SLC wiring at the building entry/exit.

Wiring connected to the surge suppressor output must remain within the building while wiring connected
to the surge suppressor input may be routed outside the building as shown below.

Building #2

Building #1

Installation

P

P = Primary
S = Secondary

PP

Surge Suppressor

Primary devices meet
NEC Requirements

P

FACP

S

S

SLC-ssbuild1.cdr

Secondary devices meet
UL1459 (UL1950)

Mounting of the surge suppressor must be inside the FACP enclosure or in a separate enclosure listed for
fire protective signaling use.

• Locate on an available stud and secure with nut.

• Unit is connected in series with the SLC Loop to protect the Control Panel.

• Provide a common ground to eliminate the possibility of a differential in ground potent ials.

The SLC Wiring Manual PN 51309:K 2/14/08 55

Appendix B: Surge Suppression Installation

Wiring Diagram for MS-9200

DTK-2LVLP-F Connections

2LVLP-F

Optional 4-wire Return Loop
Style 6 (Class A)

OUT

SLC Terminal Block

2LVLP-F

–

+

SLC Loop

ININOUT

SLC-lvlp1.cdr

PLP-42N Connections

PLP-42N

GRND

INPUT

L1 L2 L3 L4

OUTPUT

L1 L2 L3 L4

Optional 4-wire Return Loop
Style 6 (Class A)

SLC Terminal Block

PLP-42N

–

+

SLC Loop

Note: Use 12AWG (3.25mm2) to 18AWG (0.75mm2) wire with crimp-on connectors to connect the unit’s ground
terminal to equipment ground. Wire length must be minimized to provide best protection.

SLCP-030 Connections

INPUT

L1 L2 L3 L4

SLCP-30

GRND

OUTPUT

L1 L2 L3 L4

SLC-plpn1.cdr

Optional 4-wire Return Loop
Style 6 (Class A)

56

SLC Loop

–
+

OUT

SLCP-30

ININOUT

SLC Terminal Block

SLC-slcp1.cdr

The SLC Wiring Manual PN 51309:K 2/14/08

Installation Appendix B: Surge Suppression

Wiring Diagram for MS-9600, MS-9600LS, MS-9600LSC, MS-9600UDLS,
MS-9200UD, MS-9200UDLS and MS-9050UD

DTK-2LVLP-F Connections

2LVLP-F

Optional 4-wire Return Loop
Style 6 (Class A)

OUT

SLC Terminal Block

2LVLP-F

+

–

SLC Loop

ININOUT

SLC-lvlp4.cdr

PLP-42N Connections

PLP-42N

GRND

INPUT

OUTPUT

L1 L2 L3 L4

L1 L2 L3 L4

Optional 4-wire Return Loop
Style 6 (Class A)

SLC Terminal Block

PLP-42N

+

INPUT

L1 L2 L3 L4

SLCP-30

SLCP-30

GRND

OUTPUT

L1 L2 L3 L4

SLC-plpn4.cdr

Optional 4-wire Return Loop
Style 6 (Class A)

OUT

SLC Terminal Block

–

SLC Loop

Note: Use 12AWG (3.25mm2) to 18AWG (0.75mm2) wire with crimp-on connectors to connect the unit’s ground
terminal to equipment ground. Wire length must be minimized to provide best protection.

SLCP-030 Connections

SLC Loop

+
–

ININOUT

The SLC Wiring Manual PN 51309:K 2/14/08 57

SLC-slcp4.cdr

Appendix C: Terminal Conversion Charts for New & Legacy Devices CRF-300

Appendix C: Terminal Conversion Charts for New &

Legacy Devices

CRF-300

Common 2

Closed 2

Open 2

Common 1

Closed 1

Legacy Module

Legacy Module Terminal Number Terminal Function Newer Module Terminal Number

1SLC -1
2SLC +2
3 Unused 3
4 Normally Open (1) 5
5 Normally Closed (1) 6
6 Relay Common (1) 7
7 Normally Open (2) 8
8 Normally Closed (2) 9

SLC ­SLC +

Open 1

Common 2

Closed 2

Open 2

Common 1

Closed 1

Newer Module

SLC ­SLC +

Open 1

9 Relay Common (2) 10
N/A Unused 4
N/A Unused 11

Table 5 CRF-300 Terminal Conversions

58

The SLC Wiring Manual PN 51309:K 2/14/08

CMF-300 and MMF-302 Appendix C: Terminal Conversion Charts for New & Legacy Devices

CMF-300 and MMF-302

Note: All module polarities are shown in standby condition, which reflects the labels on the new modules.

A-

A+

B/A +

B/A -

SLC ­SLC +
VDC ­VDC +

Legacy Module

VDC -

VDC +

A-

A+

B/A +

B/A -

Newer Module

SLC ­SLC +

Legacy Module Terminal Number Terminal Function Newer Module Terminal Number

1SLC -1
2SLC +2
3VDC -11
4VDC +10
5 Unused 5
6 Solenoid B/A - 6
7 Solenoid B/A + 7
8 Solenoid A + 8
9 Solenoid A - 9
N/A Unused 3
N/A Unused 4

Table 6 CMF-300 and MMF-302 Terminal Conversions

The SLC Wiring Manual PN 51309:K 2/14/08 59

MMF-300

Class A Supervision -

Class A Supervision+

Class A/B Supervision +

Class A/B Supervision -

Legacy Module

SLC ­SLC +

Class A Supervision ­Class A Supervision+

Class A/B Supervision +

Class A/B Supervision -

Newer Module

SLC ­SLC +

Legacy Module Terminal Number Terminal Function Newer Module Terminal Number

1SLC -1
2SLC +2
3Unused3
4Unused4
5Unused5
6 Class A/B Supervision - 6
7 Class A/B Supervision + 7
8 Class A Supervision + 8
9 Class A Supervision - 9
N/A Unused 10
N/A Unused 11

Table 7 MMF-300 Terminal Conversions

60 The SLC Wiring Manual PN 51309:K 2/14/08

Index

Numerics

24 VDC detectors 53
24 VDC NAC power 40
24 VDC power

MS-9200, MS-9600 17

A

AD350 Detector 11, 50
AD355 11
address capacity 21
addressable

devices 21

modules 10, 25
Alarm Verification 50
analog intelligent devices 10
Authority Having Jurisdiction 12
auxiliary devices 11

B

B224 RB Relay Detector Base 50
B224 RI Isolator Detector Base 50
B350LP Detector Base 50
B501BH Sounder Detector Base 50
Bases, detector 50
BEAM355 11, 51
BEAM355S 11, 51
BG-12LX 12, 52
building entry/exit 55

C

circuit fault 10
Classic Loop Interface Protocol 10
CLIP (Classic Loop Interface Proto­col) 10
CLIP Mode 12
close nippled conduit 24
CMF-300 Control Module 11
CMF-300 module 40, 41, 42

installation 40

wiring 41
CMF-300-6

address disabling 43
CMF-300-6 Control Module 11
CMF-300-6 module 40, 45, 46

address setting 43

circuit board 44

installation 43

short circuit protection 43

Style selection 43

wiring 45
common ground 55
communication protocol 10
conduit, close nippled 24
connectors, crimp-on 56, 57
Control Modules 11
control panel 8
CP350 Detector 11, 50

CP355 11
CRF-300 module, wiring of 47
CRF-300 Relay Module 11
CRF-300-6 module

address disabling 49
address setting 49
circuit board 48

wiring 49
CRF-300-6 module, wiring of 47
CRF-300-6 Relay Module 11

D

D350P Detector 11
D350RP Detector 11
DC resistance 14, 15
detector base, wiring of 50
Detector Bases 50
detector bases 50
detectors 50

listing 11
devices

addressable 21

auxiliary 11

supervised 54
document sources 9
drain wire 16
dry-contact 11
DTK-2LVLP-F 55

E

electrical interference 13
End-of-Line Resistor 41, 45

F

fault 12, 23
fault condition 21
Fault Isolator Module 21
Fire alarm service 29
foil 16
Form C relay 50
Form-C contacts 47
Form-C relays 11
four-wire configuration 42, 46

G

ground terminal 56, 57

H

H350 Detector 11, 50
H350R Detector 11
H355 11
H355HT 11
H355R 11
Heat Detector 50

I

I300 21

I300 Isolator Module 10
Initiating Device Circuits 25, 31, 33,
35
integral relay 21
Ionization Detector 50
Isolator Module 10

how it works 21
wiring of 21

isolator modules 23, 24

K

key-lock reset 52

L

LEDs 50
LiteSpeed 10
local building code 55
loop resistance 14, 15
loops 15

M

MDF-300 Dual module 10, 25, 35
MDF-300 module

wiring 35
metal conduit 16, 23
minimum resistance 53
MMF-300 module 10, 25, 31, 32
MMF-300-10 Module 10
MMF-300-10 module 27, 33, 34

wiring 33, 34
MMF-301 module 10, 25
MMF-302 module 10, 25, 36, 37

wiring 36
MMF-302-6 Interface Module 10
MMF-302-6 module 28, 38, 39

wiring 38
module circuits 25
modules

addressable 10

control 11

isolator 10

monitor 10

relay 11
Monitor Modules 10, 25
Multicriteria Detector 50
Multi-Point Module 30

N

NAC power 40
NAC wiring 40
NEC Article 800 55
NFPA Style 4

wiring of 19

with I300 22
NFPA Style 6

wiring of 20

with I300 23

The SLC Wiring Manual PN 51309:K 2/14/08 61

Index

NFPA Style 7 21

with isolator modules 24

NFPA Style B

IDC wiring 31, 33, 35, 36, 38

NFPA Style D

IDC wiring 32, 34, 37, 39

NFPA Style Y 40

wiring of 41, 45

NFPA Style Z 40

wiring of 42, 46
Nonresettable power 17
normally closed contacts 54
Notification Appliance Circuit 11
notification appliances 54

O

older version and newer version mod­ules 8

P

performance 12
Photoelectric Detector 50
PLP-42N 55
Polling Protocols 10
power run 53, 54
power supervision relay 41, 42, 45,
46, 54
proper gauge wire 53
Pull Station 12
pull station 24

wiring of 52

R

RA400Z 50
rate of rise 11
ratings, relay contact 40, 47
relay contact ratings 40, 47
Relay Module 11
relays

Form-C 11
Remote LED Annunciator 50
Resettable power 17
resistance 14, 15
rotary switches 29, 34, 35, 36, 37, 38,
39, 50

SLC terminal block 16
SLC wiring 31, 32, 33, 34, 35, 36, 37,
38, 39
SLCP-030 55
Smoke Detectors 50
Sprinkler supervision 29
supervised

circuit 54

devices 54
supplying power 53
suppressors, surge 55
surge protector 10, 12, 55
switching 40

T

terminal blocks 17
termination of shield 16
Thermal Detector 50
thermistor sensing circuit 11
trouble conditions 12, 21
T-tapping 14, 19, 20, 23, 24
twisted-pair shielded wiring 13
two-wire configuration 41, 45

U

Unregulated power 17

V

verification cycle 50

W

Waterflow alarm service, automatic
and manual 29
wire length 14, 15
wire size 13
wiring

NACs 40

of an isolator module 21
wiring pair 55
wiring requirements 13
wiring style requirements 12

S

SD350 Detector 11, 50
SD350T Detector 11
SD355 11
SD355T 11
sensing circuit, thermistor 11
short circuit 21
Signaling Line Circuit 10
Single Point Module 29
SLC address, setting of 29, 50
SLC connections 17

62

The SLC Wiring Manual PN 51309:K 2/14/08

Limited Warranty

Honeywell International Inc. warrants products manufactured by it

to be free from defects in materials and workmanship for eighteen
(18) months from the date of manufacture, under normal use and
service. Products are date stamped at time of manufa cture. The sole
and exclusive obligation of Honeywell International Inc. is to repair
or replace, at its option, free of charge for parts and labor, any part
that is defective in materials or workmanship under normal use and
service. All returns for credit are subject to inspection and testing at
the factory before actual determination is made to allow credit.
Honeywell International Inc. does not warrant products not
manufactured by it, but assigns to the purchaser any warranty
extended by the manufacturer of such products. This warranty is void
if the product is altered or repaired by anyone other than Honeywell

International Inc. or as expressly authorized by Honeywell
International Inc. in writing, or is serviced by anyone other than
Honeywell International Inc. or its authorized distributors. This

warranty is also void if there is a failure to maintain the products and
systems in which they operate in a proper and workable manner. In
case of defect, secure a Return Material Authorization form from our
Return Authorization Department.

This writing constitutes the only warranty made by Honeywell

International Inc., with respect to its products. Honeywell
International Inc., does not represent that its products will prevent

any loss by fire or otherwise, or that its products will in all cases
provide the protection for which they are installed or intended. Buyer
acknowledges that Honeywell International Inc., is not an insurer
and assumes no risk for loss or damages or the cost of any
inconvenience, transportation damage, misuse, abuse, accident or
similar incident.

HONEYWELL INTERNATIONAL INC. GIVES NO WARRANTY,
EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR
ANY PA RTICULAR PURPOSE, OR OTHERWISE WHICH EXTENDS
BEYOND THE DESCRIPTION ON THE F ACE HEREOF. UNDER NO
CIRCUMSTANCES SHALL HONEYWELL INTERNATIONAL INC.
BE LIABLE FOR ANY LOSS OF OR DAMAGE TO PROPERTY,
DIRECT, INCIDENTAL OR CONSEQUENTIAL, ARISING OUT OF
THE USE OF, OR INABILITY TO USE HONEYWELL

INTERNATIONAL INC.’S PRODUCTS. FURTHERMORE,
HONEYWELL INTERNATIONAL INC. SHALL NOT BE LIABLE FOR

ANY PERSONAL INJURY OR DEATH WHICH MAY ARISE IN THE
COURSE OF, OR AS A RESULT OF, PERSONAL, COMMERCIAL
OR INDUSTRIAL USE OF ITS PRODUCTS.

This warranty replaces all previous warranties and is the only
warranty made by Honeywell International Inc. No increase or
alteration, written or verbal, of the obligation of this warranty is
authorized.

Warn-HL-05-2007.fm

World Headquarters

1 Firelite Place

Northford, CT 06472-1653 USA

203-484-7161

fax [phone]

www.firelite.com