Fiat Panda 2008, New Panda 2008 User Manual

This Supplement describes the main fea­tures of Fiat Panda 4 x 4 versions togeth­er with a few instructions for use. For all the other information not contained here­in, refer to the Owner Handbook this sup­plement is attached to.
FIAT PANDA 4 x 4 DRIVE LINE
The Fiat Panda 4 x 4 has a transmis­sion system comprising two differ­entials and an electronically con­trolled coupling.
Thanks to this system, under poor grip conditions the four-wheel drive will engage automatically (i.e.: no driver’s action required) and provide optimum torque distribution be­tween front and rear axle.
Fiat Panda 4 x 4 is therefore suited for all types of roads: in fact, it is ca­pable of coping well with snowy, icy, muddy and dirt roads, even with steep slopes.
SUMMARY
ABS SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ESP SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ELD - ELECTRONIC LOCKING DIFFERENTIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
HEADLIGHT WASHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
IF A TYRE IS PUNCTURED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
IF AN EXTERIOR LIGHT BURNS OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
WASHING THE CAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TOWING THE CAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TOWING TRAILERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SERVICE SCHEDULE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ENGINE CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
BODY VERSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
WHEELS AND TYRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
INFLATING PRESSURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SNOW CHAINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
STEERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CAPACITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
WEIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FUEL CONSUMPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CO
EMISSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2
FIAT PANDA 4 x 4
1
ABS SYSTEM
This version is provided as standard with the ABS system and includes:
EBD (Electronic Braking Force Distrib­ution), that distributes the braking ef­fect between front and rear wheels;
MSR (Motor Schleppmomenten Regelung - Engine braking torque con­trol system), that in case of sudden gear shifting cuts in (preventing wheel lock­ing at slow down when releasing the ac­celerator) providing torque to the en­gine thus preventing excessive driving wheel drive that, specially in poor grip conditions can lead to the loss of sta­bility.
FIAT PANDA 4 x 4
ESP SYSTEM (Electronic Stability Program) (where provided)
Le système ESP comprend:
Le système EBD (Electronic Braking force Distribution) qui permet de ré­partir le freinage entre les roues avant et arrière.
ABS (Antiblocking System), système an­tiblocage des roues en freinage;
ASR (Active Spin Regulation), qui per­met de contrôler le patinage des roues motrices en intervenant sur les freins et sur le couple moteur;
MSR (Motor Schleppmomenten Regelung – Régulation du couple de freinage du moteur), qui intervient en cas de changement brusque de vitesse (ce qui évite le blocage des roues en phase de décélération, lorsque l’ac­célérateur est relâché), en augmentant le couple du moteur pour éviter l’en­traînement excessif des roues motrices. En effet, ce phénomène, surtout dans des conditions de faible adhérence, peut provoquer une perte de stabilité du véhicule;
HBA (Hydraulic Brake Assist), système qui rend plus efficace un éventuel freinage d’urgence ;
HH (Hill Holder), qui, en conditions de pente ou de côte, si la pédale de frein est enfoncée, maintient le véhicule freiné le temps nécessaire au départ, permettant de passer le pied du frein à l’accélérateur sans que la voiture recule.
Pour plus de précisions sur les fonctions susmentionnées, se référer à la Notice d’entretien, section Système ESP.
Par rapport à la version deux roues motri­ces, le système ESP comprend la fonction ELD (Electronic Locking Differential), qui optimise la traction.
2
ELD - ELECTRONIC LOCKING DIFFERENTIAL (where provided)
The ELD (Electronic Locking Differential) is a further aid when driving or starting the car in poor grip conditions (snow, ice, mud, etc.) since it enables to distribute power adequately to the same axle when one or more wheels are slipping.
The ELD actually brakes the wheels that are loosing grip (or that are slipping more than others) and it transmits power to wheels having best grip.
This function can be turned on manually by pressing the ELD button in the dash­board and works below a level of 50 km/h.
When this speed is exceeded, it is auto­matically deactivated (the LED in the ELD button remains on) and it is reactivated as soon as the speed goes below the level of 50 km/h.
fig. 1
F0G0605m
ELD operation
At start-up the ELD system is off.
To turn the ELD system on, press button fig. 1; the relevant button led will turn on.
The activation of the ELD system involves the following functions being switched on:
– Permanent four wheel drive, so that the vehicle is more responsive;
– Inhibition of the ASR function, in order to fully exploit the engine torque;
– Differential lock effect on the front and rear axles, via the braking system, to im­prove drive on uneven surfaces.
If there is a problem with the ELD system, the (ESP) warning light will come on con­stantly.
fig. 2/a
fig. 2/b
F0G0743m
F0G0742m
4x4 Drive - Signals
The warning light in fig. 2a-2b provides two different types of signals:
signalling with flashing light: this indi­cates that the differential lock function (ELD) is activated, for versions with ESP only and with the ELD button pressed;
FIAT PANDA 4 x 4
3
signalling with light on constantly: this indicates that there is a problem with the 4x4 drive; go to a Fiat Dealership as soon as possible (where provided, the display will show a dedicated mes­sage). In addition, on versions with ESP, if the ELD is on, the LED in the button will go out.
FIAT PANDA 4 x 4
HEADLIGHT WASHER (where provided)
The headlight washing system consists of two nozzles for washing the external headlight lens. This function can be acti­vated using the windscreen washer stalk only if dipped beams or main beams are on. Operating the stalk to wash the wind­screen will automatically start the head­light washer.
This version features a windscreen wash­er fluid reservoir with improved capaci­ty, i.e.: 4.5 litres.
IF A TYRE IS PUNCTURED
General instructions
The car can be delivered (upon request/if provided) with space-saver spare wheel or with quick tyre repair kit (called Fix & Go).
Wheel changing and correct use of the jack and space-saver spare wheel call for some precautions as listed in the Owner Hand­book this Supplement is attached to. In the Owner Handbook you will also find how to use the Fix & Go kit (quick tyre repair kit).
To change a wheel proceed as follows:
stop the car in a position that is not dangerous for oncoming traffic where you can change the wheel safely. The ground should be flat and adequately firm;
turn the engine off and pull up the hand­brake;
engage first gear or reverse;
4
fig. 3
fig. 4
take out the tool bag fig. 3 set under the
F0G0607m
F0G0608m
driver’s seat and take it near the wheel to be changed;
loosen the clamping device B-fig. 4;
take the space-saver spare wheel A;
loosen the bolts on the wheel to be replaced with the wrench provided A- fig. 5;
fig. 5
fig. 6
turn the jack handle to open it partly;
place the jack near the wheel to be
F0G0609m
F0G0610m
changed in line with mark O on the sidemember fig. 6;
make sure the groove F on the jack fits correctly into the sidemember ridge G;
fig. 7
alert other passengers that the car is
F0G0233m
about to be raised; all persons should be kept away from the car until it has been lowered again;
fit handle H-fig. 6 to the jack device I and raise the car until the wheel is a few inches off the ground. When turning the jack handle make sure that it can be used easily and take care not to scrape your hand against the ground. The moving parts of the jack (screws and joints) may also cause injury if touched. Clean off any grease;
remove the wheel cap (if any) after un­screwing the three relevant bolts then, unscrew the fourth bolt L-fig. 7 and re­move the wheel;
FIAT PANDA 4 x 4
5
turn the jack handle to lower the car and remove the jack;
fasten the bolts completely, working in a criss-cross fashion as shown in fig. 9.
After changing the wheel
put the jack partly open and the tools used into the tool bag;
fig. 8
F0G0204m
stow the bag with tools into its place
fig. 10
F0G0615m
under the driver’s seat.
IMPORTANT Replaced wheel shall be placed in the boot under the cover mat as shown in fig. 10.
IMPORTANT Do not use inner tubes with tubeless tyres. Check tyre and space­saver spare wheel pressure regularly.
IMPORTANT Changing original wheels with others of different type (i.e.: with al­loy rim instead of steel rims and vice ver­sa) will involve to change the whole set of wheel bolts with others of suitable length. It is however recommended to keep replaced bolts in the event of future refitting of the original wheels.
FIAT PANDA 4 x 4
fig. 9
make sure the space-saver spare wheel
F0G0206m
supporting surfaces on the hub are clean and free from any impurities that could cause wheel bolts loosening;
fit the space-saver spare wheel match­ing one of the wheel holes O with pins N-fig. 8;
fasten the four fastening bolts;
6
IF AN EXTERIOR LIGHT BURNS OUT
(Fiat Panda 4 x 4 CROSS version)
IMPORTANT To change an external light on Fiat Panda 4 x 4 and Fiat Panda 4 x 4 Climbing versions, refer to the Owner Handbook this Supplement is attached to.
For the type of bulb and power rating re­fer to paragraph “When needing to change a bulb” in section “In an emergency” in the attached Owner Handbook.
FRONT LIGHT UNITS
To change the dipped beam bulb, proceed as follows:
remove the cover A-fig. 11;
disconnect the connector C-fig. 12;
release the bulb holder catch A;
remove the bulb B and fit the new bulb.
fig. 11
fig. 12
F0G0617m
F0G0618m
To change the front sidelight bulb, pro­ceed as follows:
remove the cover A-fig. 11;
remove the bulb holder A-fig. 12
remove the bulb B;
fit the new bulb.
fig. 13
fig. 14
F0G0619m
F0G0628m
remove the cover A-fig. 11;
disconnect the connector D-fig. 14;
turn slightly the bulb holder B and re­move it;
remove the bulb C and fit the new bulb.
To change the main beam bulb, proceed as follows:
FIAT PANDA 4 x 4
7
Loading...
+ 18 hidden pages