How it Works
Fiat
Loading...
500l Living 2014
Owner's Manual
420 pgs10.24 Mb0

Fiat 500l Living 2014 Owner's Manual

FIAT500L
OWNER HANDBOOK
Dear Customer,
We would like to congratulate and thank you for choosing a Fiat 500L. We have written this handbook to help you get to know all the features of your car and use it in the best possible way. You are recommended to read it right through before taking to the road for the first time. It contains important information, advice and instructions for the use of the car which will help you get the very best out
of your Fiat. The handbook also provides a description of special features and tips as well as essential information for correct care, maintenance, safe car driving and use and preservation of your Fiat over time.
Carefully read the warnings and indications marked with the following symbols:
personal safety;
car safety;
environmental protection.
The enclosed Warranty Booklet lists the services that Fiat offers to its Customers:
❒ the Warranty Certificate with terms and conditions for maintaining its validity; ❒ the range of additional services available to Fiat Customers.
We are sure that these will help you familiarise with your new car and appreciate it and the care provided by the people at Fiat.
Enjoy reading. Happy motoring!
This Owner Handbook describes all the versions of the Fiat 500L. As a consequence, you should only consider the information which is related to the trim level, engine and version that you have purchased.All data contained in this publication are purely indicative. Fiat Group Automobiles can modify the specifications of the vehicle model described in this publication at any time, for technical or commercial
reasons. For further information, contact a Fiat Dealership.
ESSENTIAL INFORMATION!
REFUELLING
Petrol engines: only refuel with unleaded petrol
with octane rating (RON) not less than 95 in compliance with the European specification EN228.
The use of petrol that does not conform to the above-mentioned specification will cause the EOBD warning light to switch on and the irregular operation of the engine.
Diesel engines: only refuel with diesel for motor vehicles in compliance with the European specification EN590. The use of other products or mixtures may damage the engine beyond repair and consequently invalidate the warranty.
STARTING THE ENGINE
Make sure that the handbrake is engaged; place the gear lever in neutral. Fully depress the clutch pedal, without pressing the accelerator, then turn the ignition key to MAR-ON and wait for the warning light to switch off (and
warning light for diesel versions); turn the ignition key to AVV and release it as soon as the engine starts.
PARKING ON FLAMMABLE MATERIAL
The catalytic converter develops high temperatures during operation. Do not park the car on grass, dry leaves, pine needles or other flammable material: fire hazard.
RESPECTING THE ENVIRONMENT
The car is fitted with a system that allows continuous diagnosis of the components related to emissions to ensure increased respect for the environment.
ELECTRICAL ACCESSORIES
If, after buying the car, you decide to add electrical accessories (with the risk of gradually draining the battery), contact a Fiat Dealership. They will calculate the overall electrical requirement and check that the car’s electrical system can support the required load.
SCHEDULED SERVICING
Correct maintenance of the car is essential for ensuring that it maintains its performance and its safety features, its environmental friendliness and low running costs for a long time to come.
THE OWNER MANUAL CONTAINS…
… important information, advice and warnings for correct use, driving safety and maintenance of your car over time. Special attention must be paid to the symbols provided
(environmental protection) (car integrity).
(personal safety)
GETTING TO KNOW YOUR CAR
DASHBOARD
The presence and position of the controls, instruments and indicators may vary according to the different versions.
fig. 1
1. Adjustable and directable air diffusers 2. Radio controls on the steering wheel (for versions/markets, where provided)
3. Exterior light control stalk 4. Instrument panel 5. Windscreen wiper/rear window wiper/trip computer control stalk
6. Adjustable and directable centre air vents 7. Fixed upper air vent 8. Passenger front airbag 9. Upper glove compartment (for versions/markets, where provided the compartment may be conditioned) 10. Storage compartment
11. Lower glove compartment 12. Control buttons 13. Heating/ventilation system or manual climate control (for versions/markets, where provided) or automatic dual zone climate control (for versions/markets, where provided)
14. USB port/AUX socket (for versions/markets, where provided) 15. vided) or radio system setup 16. Ignition switch 17. Driver front airbag 18. Cruise Control/Speed Limiter lever (for
versions/markets, where provided)
UConnect
(for versions/markets, where pro-
™
F0Y0042
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
INDEX
3
GETTING TO
KNOW YOUR CAR
CONTROL PANEL AND INSTRUMENTS
Instrument background colour and type may vary according to the version.
The warning lights speed (red range on the rev counter) corresponds to 5000 rpm.
SAFETY
VERSIONS WITH MULTIFUNCTION DISPLAY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
A. Speedometer (speed indicator) B. Multifunction display C. Rev counter D. Fuel level gauge with reserve warning light E. Engine coolant temperature gauge with overheating warning light
fig. 2
and are only present on Diesel versions. On diesel versions, the maximum engine
F0Y1107
INDEX
4
VERSIONS WITH RECONFIGURABLE MULTIFUNCTIONAL DISPLAY
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
fig. 3
A. Speedometer (speed indicator) B. Reconfigurable multifunction display C. Rev counter D. Fuel level gauge with reserve warning light E. Engine coolant temperature gauge with overheating warning light
F0Y1108
IN AN EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
INDEX
5
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
SPEEDOMETER (SPEED INDICATOR)
Shows the car speed (speedometer).
REV COUNTER
This indicates the engine rpm.
FUEL LEVEL GAUGE
This shows the amount of fuel left in the fuel tank. E - tank empty F - tank full The warning light A fig. 4 (on certain versions
together with the message on the display) switches on to indicate that approximately 6 to 8 litres of fuel are left in the tank; in these circumstances refuel at the earliest opportunity.
Do not travel with the fuel tank almost empty: the gaps in fuel delivery could damage the catalyst.
IMPORTANT The needle will point to E and warning light A will flash to indicate a fault in the system. If this is the case, go to a Fiat Dealership to have the system checked.
Under normal conditions, the needle assumes different positions within the scale depending on the usage conditions.
C - Low engine coolant temperature. H - High engine coolant temperature. The warning light B fig. 4 may switch on (with a
message on the display for some versions) to indicate that the coolant temperature is too high; in this case, stop the engine and contact a Fiat Dealership.
If the needle for the engine coolant temperature reaches the red area, stop the engine immediately and contact a Fiat
Dealership.
TECHNICAL
SPECIFICATIONS
INDEX
6
ENGINE COOLANT TEMPERATURE INDICATOR
The needle shows the temperature of the engine coolant and starts supplying indications when the fluid temperature exceeds approx. 50°C.
fig. 4
F0Y0118
DISPLAY
The car may be provided with a multifunction or reconfigurable multifunction display that shows useful information, according to the previous settings, when driving.
With the ignition key removed, the display activates and shows the time and total milometer reading (in km or miles) for a few seconds when a front door is opened/closed.
NOTE With a very low outside temperature (below 0°C) it may take longer than normal for information to appear on the display.
MULTIFUNCTION DISPLAY "STANDARD" SCREEN
The following information is shown on the display fig. 5:
Date
A
Activation of Dualdrive electric power steering
B
(CITY indication) or of ECO driving mode (ECO indication)
Gear Shift Indicator (for versions/markets, where
C
provided)
Headlight alignment position (only with dipped
D
headlights on)
Odometer (display of distance travelled in
E
kilometres/miles)
Time (always displayed, even with key removed and
F
doors closed)
Start&Stop function indication (for versions/
G
markets where provided) Outside temperature (for versions/markets, where
H
provided)
"Speed limiter" display (for versions/markets, where
I
provided)
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
fig. 5
TECHNICAL SPECIFICATIONS
INDEX
F0Y1101
7
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
RECONFIGURABLE MULTIFUNCTION DISPLAY "STANDARD" SCREEN
Versions without "Speed Limiter"
The following information appears on the display fig. 6:
Time
A
Date or trip distance display in kilometres
B
(or miles) Outside temperature (for versions/markets, where
C
provided)
Gear Shift Indicator (for versions/markets, where
D
provided)
Odometer (display of distance travelled in
E
kilometres/miles) Headlight alignment position (only with dipped
F
headlights on)
Car status indication (e.g. doors open, possible ice
G
on road, etc.)
On some versions the display shows the turbine pressure fig. 7.
TECHNICAL
SPECIFICATIONS
INDEX
8
fig. 6
F0Y1102
fig. 7
F0Y0186
Versions with "Speed Limiter"
(for versions/markets, where provided)
The following information appears on the display fig. 8:
Time
A
Date or trip distance display in kilometres
B
(or miles) Gear Shift Indicator (for versions/markets, where
C
provided) or Start&Stop function indication (for versions/markets, where provided)
"Speed limiter" display (for versions/markets,
D
where provided)
Odometer (display of distance travelled in
E
kilometres/miles)
Headlight alignment position (only with dipped
F
headlights on)
Outside temperature (for versions/markets, where
G
provided) Car status indication (e.g. doors open, possible ice
H
on road, etc.)
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
fig. 8
TECHNICAL SPECIFICATIONS
INDEX
F0Y1103
9
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
GEAR SHIFT INDICATOR
The GSI (Gear Shift Indicator) system advises the driver to change gear through a specific indication on the instrument panel fig. 9.
Through the GSI, the driver is notified that changing gear will allow a reduction in fuel consumption.
When the SHIFT UP icon (
SHIFT) is shown on the display, the GSI is advising the driver to engage a higher gear, while the SHIFT DOWN (
SHIFT) icon
advises the driver to engage a lower gear. The indication on the instrument panel remains on
until the driver changes gear or the driving conditions return to a situation where changing gear is not required to reduce consumption.
CONTROL BUTTONS
NOTE Buttons the following pages. The buttons are
and fig. 10 are described in
and on
some versions.
To scroll up through the screen and the related options or to increase the displayed value.
Press briefly to access the menu and/or go to next screen or confirm the desired menu selection.
Hold down to go back to the standard screen.
To scroll down through the displayed menu and the related options or to decrease the value displayed.
Buttons
and activate different functions
according to the following situations: ❒ within the menu, they allow you to scroll up and
down;
❒ during setting operations, they increase or
decrease the displayed value.
TECHNICAL
SPECIFICATIONS
INDEX
10
fig. 9
F0Y1104
SETUP MENU
The menu comprises a series of options which can be selected using buttons
and to access the different selection and setting operations (Setup) indicated below. Some options have a submenu.
The menu can be activated by briefly pressing the
button.
The menu comprises the following options:
❒ MENU ❒ LIGHTING ❒ HEADLIGHT ALIGNMENT (for versions/markets,
where provided)
❒ SPEED BEEP ❒ HEADLIGHT SENSOR (for versions/markets
where provided)
❒ CORNERING LIGHTS (for versions/markets,
where available)
❒ RAIN SENSOR (for versions/markets, where
provided)
❒ TRIP B ACTIVATION/DATA ❒ SET TIME ❒ SET DATE ❒ AUTOCLOSE ❒ MEASUREMENT UNIT ❒ LANGUAGE ❒ WARNINGS VOLUME ❒ BELT BUZZER ❒ SERVICE ❒ AIRBAG/PASSENGER BAG (for versions/markets,
where provided)
❒ DAYTIME RUNNING LIGHTS (for versions/
markets, where provided)
❒ CITY BRAKE C./COLLISION MITIGATION
(for versions/markets, where provided)
❒ EXIT MENU
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
fig. 10
TECHNICAL SPECIFICATIONS
INDEX
F0Y0035
11
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Selecting an option from t he main menu without a submenu:
❒ briefly press the
option to be set;
❒ press buttons
select the new setting;
❒ briefly press the
and to go back to the same main menu option selected previously.
Selecting an option from t he main menu with a submenu:
❒ briefly press the
submenu option;
❒ press buttons
scroll through all the submenu options;
❒ briefly press the
submenu option and to open the relevant setup menu;
❒ press buttons
select the new setting for this submenu option;
❒ briefly press button
at the same time go back to the previously selected menu option.
button to select the main menu
or (with single presses) to
button to store the new setting
button to display the first
or (with single presses) to
button to select the displayed
or (with single presses) to
to store the new setting and
MENU ITEMS
Note With uconnect™ system (for versions/ markets where provided), some Menu items are shown and managed on the display of the latter and not on the instrument panel display (refer to the uconnect™ supplement).
Menu
This option allows you to access the Setup Menu. Press the
Menu items. Hold down the
screen.
Lighting (Interior light adjustment) (with side lights on only)
With the side lights on, this function is used to set the brightness of the instrument panel, uconnect™ system controls (for versions/markets where provided) and automatic climate control system controls (for versions/markets where provided) to 8 levels.
Proceed as follows to adjust the brightness: ❒ press button
flashes on the display;
❒ press button or to set the required
brightness level;
❒ press the
screen or hold the button down to return to the standard screen without saving.
or button to select the various
button to return to the standard
briefly. The level set previously
button briefly to return to the menu
12
Note On versions with reconfigurable multifunction display adjustment can be made both with lights off ("daytime" mode brightness level) and with lights on ("nighttime" mode brightness level).
Headlamp alignment (Headlamp alignment corrector position adjustment)
(for versions/markets, where provided)
This function allows the headlamp alignment corrector position to be adjusted (on 4 levels).
To carry out the adjustment, proceed as follows: ❒ press button
flashes on the display;
❒ press button ❒ press the
screen or hold the button down to return to the standard screen without storing.
Speed Beep (Speed limit)
This function is used to set the car speed limit (km/h or mph); the driver is immediately alerted when this limit is exceeded.
To set the desired speed limit, proceed as follows: ❒ briefly press the
the text "Speed Beep";
❒ press button
activation (On) or deactivation (Off);
❒ if the function is on, press
desired speed limit and then press
briefly. The level set previously
or to adjust the position;
button briefly to return to the menu
button: the display will show
or to select speed limit
or to select the
to confirm.
Note Setting is possible between 30 and 200 km/h, or 20 and 125 mph, according to the previously set unit. See the "Measurement unit (Measurement unit adjustment)" paragraph described below. The setting will increase/decrease by 5 units each time button
/ button to automatically increase/decrease the setting rapidly. Complete the adjustment with single presses of the button when you approach the desired value.
❒ press the
screen or hold the button down to return to the
standard screen without storing. To cancel the setting, proceed as follows: ❒ briefly press the
display;
❒ press button ❒ press the
screen or give the button a long press to return
to the standard screen without storing.
/ is pressed. Hold down the
button briefly to return to the menu
button: "On" will flash on the
: "Off" will flash on the display;
button briefly to return to the menu
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
INDEX
13
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
Headlight sensor (Automatic headlight/dusk sensor sensitivity adjustment)
(for versions/markets, where provided)
This function is used to turn the headlights on or off according to external light conditions.
The dusk sensor sensitivity can be adjusted according to 3 levels (level 1 = minimum sensitivity, level 2 = medium sensitivity, level 3 = maximum sensitivity); the greater the sensitivity set, the less the external light variation needed to turn on the lights (e.g. with a setting on level 3 at sunset the headlights switch on earlier than in levels 1 and 2).
Proceed as follows to set: ❒ press button
flashes on the display;
❒ press the
adjustment;
❒ press the
screen or hold the button down to return to the standard screen without storing.
Cornering lights (Activation/deactivation of cornering lights)
(for versions/markets, where provided)
This function activates/deactivates ("On"/"Off") the cornering lights (see the description in the “Exterior lights” paragraph).
briefly. The level set previously
or button to make the
button briefly to return to the menu
Proceed as follows to activate/deactivate the lights: ❒ press button
the display, according to what has been previously set;
❒ press ❒ press the
screen or hold the button down to return to the standard screen without storing.
Rain sensor (Rain sensor sensitivity adjustment)
(for versions/markets, where provided)
This function allows you to adjust the rain sensor sensitivity to 4 levels.
To set the required sensitivity level, proceed as follows:
❒ press button
previously flashes on the display;
❒ press the
adjustment;
❒ press the
screen or hold the button down to return to the standard screen without storing.
briefly. "On" or "Off" flash on
or to make your choice;
button briefly to return to the menu
briefly. The sensitivity “level” set
or button to make the
button briefly to return to the menu
14
INDEX
Activation/Trip B data (ActivatingTrip B)
With this function it is possible to activate ("On") or deactivate ("Off") the Trip B display (partial trip). For more information see the "Trip computer" paragraph.
For activation/deactivation, proceed as follows: ❒ press the
On or Off according to the previous setting;
❒ press the
adjustment;
❒ press the
screen or give the button a long press to return to the standard screen without storing.
Time adjustment (Clock adjustment)
This function enables the clock to be set through two submenus: “Time” and “Format”.
To carry out the adjustment, proceed as follows: ❒ press button
submenus "Time" and "Format";
❒ press the
the two submenus;
❒ once you have selected the submenu to be
changed, press the button
❒ if the "Time" submenu is selected and button
pressed briefly, "hours" will flash on the display. Press the adjustment;
button briefly to make the display flash
or button to make the
button briefly to return to the menu
briefly. The display shows the two
or button to switch between
briefly;
is
or button to make the
❒ pressing the
flash on the display. Press the
to make the adjustment; ❒ if the "Format" submenu is selected and button
is pressed briefly, the display mode will flash on the display. Press the select "12h" or "24h" mode. When you have carried out the required settings, briefly press the
button to go back to the submenu screen or hold the button down to go back to the main menu screen without storing the new settings.
Hold down the standard screen or to the main menu according to the menu items where you are in.
IMPORTANT The setting will increase or decrease by one unit each time the button pressed. Keeping the button pressed causes an automatic rapid speed increase/decrease. Complete the setting by briefly pressing the button when you approach the required value.
button briefly again: the "minutes"
or button
or button to
button again to return to the
or is
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
INDEX
15
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
Set date (Setting the date)
Using this function it is possible to update the date (year - month - day).
To carry out the adjustment, proceed as follows: ❒ press button
display;
❒ press the
adjustment;
❒ press button
display;
❒ press the
adjustment;
❒ press button
display;
❒ press the
adjustment;
❒ press the
screen or give the button a long press to return to the standard screen without storing.
IMPORTANT The setting will increase or decrease by one unit each time the button pressed. Keeping the button pressed causes an automatic rapid speed increase/decrease. Complete the setting by briefly pressing the button when you approach the required value.
briefly. The "year" flashes on the
or button to make the
briefly. The "month" flashes on the
or button to make the
briefly. The "day" flashes on the
or button to make the
button briefly to return to the menu
or is
Autoclose (Automatic door lock operation with car running)
If this function is On, it automatically locks the doors when a speed of 20 km/h is exceeded.
Proceed as follows to activate or deactivate this function:
❒ press button
display, according to what has been previously set;
❒ press ❒ press the
submenu screen or hold the button down to return to the main menu screen without saving;
❒ hold down the
standard screen or to the main menu according to the menu items where you are in.
briefly. "On" or "Off" flash on the
or to make your choice;
button briefly to return to the
button again to return to the
16
INDEX
Unit of measurement (Setting the unit of measurement)
With this function it is possible to set the units through three submenus: "Distances", "Consumption" and "Temperature".
To set the desired measurement unit, proceed as follows:
❒ press button
three submenus;
❒ press button
three submenus;
❒ once you have selected the submenu to be
changed, press the button
❒ if the "Distances" submenu is selected and button
is pressed briefly, the display shows "km" or
"mi" depending on the previous setting;
❒ press ❒ if the "Consumption" submenu is selected and
button "km/l", "l/100km" or "mpg" depending on the previous setting. If the measurement unit set for "Distances" is "km", the display allows the measurement unit ("km/l" or "l/100km") for Consumption to be set. If the measurement unit set for "Distances" is "mi", the display will show Consumption in "mpg";
❒ press
briefly. The display will show the
or to scroll through the
briefly;
or to make your choice;
is pressed briefly, the display shows
or to make your choice;
❒ if the "Temperature" submenu is selected and
button or "°F" depending on the previous setting;
❒ press
Once the required settings are made, briefly press button the button down to return to the main menu screen without storing.
Hold down the standard screen or to the main menu according to the menu items where you are in.
Language (Language selection)
Display messages can be set to be shown in different languages: Italian, German, English, Spanish, French, Portuguese, Polish, Dutch, Turkish (the list varies according to the market).
To set the desired language, proceed as follows: ❒ press button
previously flashes on the display;
❒ press ❒ press the
screen or hold the button down to return to the standard screen without storing.
is pressed briefly, the display shows "°C"
or to make your choice;
to go back to the submenu screen or hold
button again to return to the
briefly. The “language” set
or to make your choice;
button briefly to return to the menu
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
INDEX
17
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
Warnings volume (Adjusting the alert/warning acoustic signal volume)
With this function the volume of the buzzer which accompanies the display of any failure/warning can be adjusted to 8 levels.
To set the desired volume, proceed as follows: ❒ press button
previously flashes on the display;
❒ press ❒ press the
screen or hold the button down to return to the standard screen without storing.
Seat belt buzzer (SBR buzzer reactivation)
This function can only be displayed after a Fiat Dealership has deactivated the SBR system (see paragraph “SBR system” in the “Safety” chapter).
To reactivate this function, proceed as follows: ❒ press the
display. Press the will appear;
❒ press the
submenu screen or hold the button down to return to the main menu screen without saving.
briefly. The volume “level” set
or to make your choice;
button briefly to return to the menu
button briefly; "Off" will flash on the
or button and "On"
button briefly to return to the
Service (Scheduled servicing)
With this function it is possible to view information on mileage or time intervals for servicing.
To consult this display, proceed as follows: ❒ press button
service interval in kilometres (km) or miles (mi) according to the previous setting (see the "Units of measurement" paragraph);
❒ press the
screen or hold it down to return to the standard screen.
Note The “Scheduled Servicing Plan” includes car maintenance at fixed intervals, refer to the "Maintenance and care" chapter. This message is displayed automatically - when the key is turned to MAR-ON - 2,000 km (or equivalent value in miles) before these deadlines and reappears every 200 km (or equivalent value in miles). Below 200 km servicing indications are more frequent. The display will be in km or mi depending on the measurement unit settings. When one of the next scheduled deadlines is approaching, the word “Service” will appear on the display, followed by the number of kilometres or miles lef t, when the key is turned to MAR-ON. Contact a Fiat Dealership. The operations in the “Scheduled servicing plan” will be performed and the message will be reset.
briefly. The display shows the
button briefly to return to the menu
18
INDEX
Airbag/Passenger bag (Activation/deactivation of passenger side front airbag and side bag for pelvis, chest and shoulder protection - for versions/markets, where provided)
This function allows the passenger airbag to be activated / deactivated.
Proceed as follows: ❒ press the
pass: Off" (to deactivate) or "Bag pass: On" (to activate) is displayed by pressing buttons
, press the button again;
❒ a confirmation request message will appear on the
display;
❒ by pressing the
confirm activation/deactivation) or "No" (to cancel);
❒ press the
the selection is displayed and you return to the menu screen; Hold down the button to return to the standard screen without storing.
Daytime running lights (D.R.L.)
(for versions/markets, where provided)
This function can be used to activate/deactivate the daytime running lights.
Proceed as follows to activate or deactivate this function:
❒ press button
submenu;
button and, after the message "Bag
and
or buttons select "Yes" (to
button briefly; a message confirming
briefly. The display shows a
❒ press button
display, according to what has been previously set;
❒ press ❒ press the
submenu screen or hold the button down to return to the main menu screen without saving;
❒ hold down the
standard screen or to the main menu according to the menu items where you are in.
City Brake Control - "Collision Mitigation"
(for versions/markets, where provided)
This function allows to activate ("On") or de-activate ("Off") the City Brake Control - "Collision Mitigation" system.
To adjust proceed as follows: ❒ press button
display, according to what has been previously set;
❒ a confirmation request message will appear on the
display;
❒ by pressing the
confirm activation/deactivation) or "No" (to cancel);
❒ press the
the selection is displayed and you return to the menu screen; Hold down the button to return to the standard screen without storing.
When the system is deactivated the dedicated warning light in the instrument panel switches on (see chapter "Warning lights and messages").
briefly. "On" or "Off" flash on the
or to make your choice;
button briefly to return to the
button again to return to the
briefly. "On" or "Off" flash on the
or buttons select "Yes" (to
button briefly; a message confirming
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
INDEX
19
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Exit menu
The last function closing the cycle of settings listed in the menu screen.
Pressing the to the standard screen without saving.
Press the option (Lighting).
button briefly will return the display
button to return to the first menu
TRIP COMPUTER
GENERAL INFORMATION
The Trip computer is used to display information on car operation when the key is turned to MAR-ON.
This function allows you to define two separate trips called “Trip A” and “Trip B” where the car's "complete journeys" are monitored in a reciprocally independent manner.
Both journeys can be reset (reset - start of a new journey).
“Trip A” is used to display the figures relating to: ❒ Outside temperature (for versions/markets, where
provided)
❒ Range ❒ Distance travelled A ❒ Average consumption A ❒ Instantaneous consumption ❒ Average speed A ❒ Trip time A (driving time).
“Trip B” may be used to display the figures relating to:
❒ Distance travelled B ❒ Average consumption B ❒ Average speed B ❒ Trip time B (driving time).
20
Note “Trip B” may be disabled (see “Activating Trip B”). “Range” and “Instantaneous fuel consumption" parameters cannot be reset.
VALUES DISPLAYED
Outside temperature (for versions/markets, where provided)
Indicates the temperature outside the passenger compartment.
Range
This indicates the approximate distance which can be travelled with the amount of fuel present in the tank.“----”will appear on the display in the following cases:
❒ range value lower than 50 km (or 30 mi) ❒ car parked with engine running for a long period.
IMPORTANT The range value variation can be affected by several factors: driving style, type of route (motorway, urban, mountain roads, etc.), conditions of use (load, tyre pressures, etc.). Trip planning must therefore take the above into account.
Average consumption
Shows the approximate average fuel consumption since the start of the new journey.
Instantaneous consumption
This value shows the fuel consumption. The value is constantly updated. The display will show “----” if the car is parked with the engine running.
Average speed
This shows the car average speed as a function of the overall time elapsed since the start of the new mission.
Trip time
Shows the time elapsed since the start of a new journey.
IMPORTANT If there is no information, the Trip computer displays "----"inplaceofthevalue. When normal operating condition is restored, calculation of different units will restart regularly. No values displayed before the failure will be reset nor will a new mission be started.
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
Distance travelled
Shows the distance covered since the start of the new journey.
TECHNICAL SPECIFICATIONS
INDEX
21
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
DISPLAYED INFORMATION
The displays shown below are reported as an example: for further information refer to the "Display" paragraph in this chapter.
Each time a value is displayed, the following information is shown fig. 11:
❒ A - animated icon in the upper part; ❒ B - name, value and unit of measure of the
selected parameter (e.g. "Range 150 km");
❒ C - the word "Trip" (or "Trip A" or "Trip B").
After a few seconds the name and value of the selected parameter are replaced by an icon fig. 12.
The icons relating to the various parameters are the following:
❒ ❒
"Range";
"Average consumption A” (if Trip A is active,
or “B” if Trip B is active);
❒
"Distance" (if Trip A is active, or “B” if
Trip B is active);
❒ ❒
"Instantaneous consumption"; "Average speed A” (if Trip A is active, or “B”
if Trip B is active);
❒
"Trip time" (if Trip A is active, or “B” if Trip B
is active);
TECHNICAL
SPECIFICATIONS
INDEX
22
fig. 11
F0Y1105
fig. 12
F0Y1106
TRIP BUTTON
This is located on the right-hand stalk fig. 13. With the ignition key turned to MAR, this button allows you to view the previously described parameters and also reset them to begin a new mission:
❒ short press: display various readings; ❒ long press: reset readings and start a new mission.
New mission
This begins after a reset: ❒ “manual” resetting by the user, by pressing the
relevant button;
❒ "automatic" resetting, when the "Trip distance"
reaches 99999.9 km or when the "Travel time" reaches 999:59 (999 hours and 59 minutes);
❒ after disconnection/reconnection of the battery.
IMPORTANT The reset operation when “Trip A” or “Trip B” details are being displayed resets the information associated with the function displayed.
Start of journey procedure
With ignition key at MAR, press and hold the TRIP button for more than 2 seconds to reset.
Exit Trip
You can automatically exit the TRIP function once all the values have been displayed or by holding the button
down for more than 1 second.
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
fig. 13
TECHNICAL SPECIFICATIONS
INDEX
F0Y0045
23
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
SYMBOLS
Special coloured labels have been attached near to or on some of the components of your car. These labels bear symbols that remind you of the precautions to be taken with regard to that particular component.
Under the bonnet there is also a label that summarises all the symbols.
THE FIAT CODE SYSTEM
To further protect your car from theft, it has been fitted with an engine immobilising system. It is automatically activated when the ignition key is removed.
There is an electronic device in each key which can identify the signal emitted, when the engine is started, from an aerial built into the ignition switch. The signal is the "password", different every time the vehicle is started, through which the control unit recognises the key and enables starting.
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
24
OPERATION
Each time the vehicle is started turning the ignition key to MAR-ON, the Fiat CODE system control unit sends an acknowledgement code to the engine control unit to deactivate the immobiliser. The code is sent only if the Fiat CODE system control unit has acknowledged the code received from the key.
Each time the ignition key is turned to STOP, the Fiat CODE system deactivates the functions of the engine management control unit.
If, during starting, the code is not correctly recognised, the instrument panel.
In this case, turn the key to STOP and then to MAR-ON; if it is still locked, try again with the other keys that come with the vehicle. Contact a Fiat Dealership if you still cannot start the engine.
warning light switches on in the
Warning light switching on while driving
If the
warning light switches on, this means that the system is running a self-diagnosis (for example for a voltage drop). Should the fault persist, contact a Fiat Dealership.
THE KEYS
KEY WITHOUT REMOTE CONTROL
The metal insert A fig. 14 enables:
❒ the ignition switch; ❒ the door lock.
To request duplicates of the key, go to a Fiat Dealership, taking an ID document and the car ownership documents.
GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY
SERVICING AND MAINTENANCE
fig. 14
TECHNICAL SPECIFICATIONS
INDEX
F0Y0117
25
GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
26
KEY WITH REMOTE CONTROL
(for versions/markets, where provided)
The metal insert A fig. 15 of the key operates:
❒ the ignition switch; ❒ the door lock.
Press button B to open/close the metal insert.
WARNING
Button B should only be pressed when
the key is away from the body, in particular from the eyes and from objects that can be spoilt (e.g. clothes). Do not leave the key unattended to avoid the button being accidentally pressed while it is being handled, e.g. by a child.
fig. 15
F0Y0019
Unlocking the doors and the tailgate
Briefly press button
: for unlocking of doors and luggage compartment, timed switching-on of internal roof lights and double flashing of direction indicators (for versions/markets, where provided).
The doors are unlocked automatically if the fuel cut-off system intervenes.
Once the doors are locked, if one or more doors or the luggage compartment are not closed correctly, the LED and direction indicators start flashing quickly.
Locking the doors and the tailgate
Briefly press button
: for locking of doors and luggage compartment, with switching-off of roof light and single flashing of direction indicators (for versions/markets, where provided).
If one or more doors are open, the doors will not be locked. This is indicated by a rapid flashing of the direction indicators (for versions/markets, where provided). The doors will be locked if the tailgate is open however.
When a speed of over 20 km/h is reached, the doors are automatically locked if this specific function has been set (only on versions with multi-function reconfigurable display).
When the doors are locked from outside the car (using the remote control), the LED above the
button will switch on for a few seconds and then
start flashing (deterrent function).
Loading...
+ 390 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use